Pressure relaxation of polystyrene and its comparison to the shear response

Isothermal pressure relaxation as a function of temperature in two pressure ranges has been measured for polystyrene using a self-built pressurizable dilatometer. A master curve for pressure relaxation in each pressure regime is obtained based on the time–temperature superposition principle, and time–pressure superposition of the two master curves is found to be applicable when the master curves are referenced to their pressure-dependent T_g. The pressure relaxation master curves, the shift factors, and retardation spectra obtained from these curves are compared with those obtained from shear creep compliance measurements for the same material. The shift factors for the bulk and shear responses have the same temperature dependence, and the retardation spectra overlap at short times. Our results suggest that the bulk and shear response have similar molecular origin, but that long-time chain mechanisms available to shear are lost in the bulk response. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3375–3385, 2007     

Interpretation of the TSDC fractional polarization experiments on the α‐relaxation of polymers

We report on the interpretation of the thermally stimulated depolarization current (TSDC) experiments, with partial polarization methods, on the dielectric α‐relaxation. The results obtained on polyvinyl acetate are rationalized on the basis of the Boltzmann superposition principle in combination with a Kohlrausch–Williams–Watts (KWW) time decay of the polarization (with the β exponent essentially temperature independent and equal to the value determined by conventional dielectric methods at T_g). From this analysis of the global TSDC spectrum we found a complex temperature dependence of the KWW relaxation time, which is Arrhenius‐like at the lowest temperatures but crosses over to the Vogel–Fulcher behavior observed above T_g in the temperature range of the TSDC peak. On the basis of these results, we found the way of predicting the TSDC spectra measured after partial polarization procedures. We found that, the distribution of activation energies and compensation behavior deduced by following the standard way of analysis are associated to the assumption of an Arrhenius‐like temperature dependence of the α‐relaxation time in the temperature range explored by TSDC. Therefore we conclude that both the distribution of activation energies and compensation behavior obtained by following the standard way of analysis do not give a proper physical picture of the α‐relaxation of glassy polymers around the glass‐transition temperature. Our results also show that the partial polarization TSDC methods are not able to give insight about the actual existence or not of a distribution of relaxation times at the origin of the nonexponentiality of the α‐relaxation of polymers. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2105–2113, 2000     

The pressure dependence of the dielectric constant and density of acetonitrile at three temperatures

The static dielectric constant of liquid acetonitrile is reported at 10, 25, and 40°C and at pressures up to 3 kbar. Densities of pure acetonitrile were measured where needed in order to analyze the dielectric measurements using the Kirkwood-Fröhlich equation. The Kirkwood correlation factorg _K was found to be less than unity with a positive temperature but negative pressure coefficient, suggesting an increasing anticorrelation of dipoles with decreased temperature and increased pressure. Theg _K factors are analyzed by a dipole pair-bonding model as outlined by Dannhauser and Flueckinger in which the lowg _K values are attributed to the presence of dimers consisting of completely anticorrelated dipoles. The implication of this model on other measurements, especially MNR relaxation studies, is examined.     

Dielectric relaxation study of N -methyl formamide with glycols using time domain reflectometry technique

The dielectric relaxation study that is static dielectric permittivity (∈₀) and relaxation time (τ) of amide of N-methyl formamide (NMF) with increasing volume percent propylene glycol (PLG) and BLG has been carried out at different temperatures. The time domain reflectometry (TDR) technique has been used to measure reflection coefficient in frequency range of 10 MHz to 20 GHz. The dielectric parameters have been obtained by fitting experimental data with the Havriliak–Negami equation. The experimental observation shows that the static dielectric permittivity and relaxation time decreases with increasing temperature. The experimental observation also shows that the static dielectric permittivity decreases and relaxation time increases with increasing percentage volume of Propylene glycol (PLG) and Butylene glycol (BLG) in NMF. The nature of (?₀) and (τ) is same for the temperature ranges (20, 30, and 40°C). The thermodynamic parameters enthalpy (ΔH) and entropy (ΔS) of the binary mixture are also reported in this work.     

Studies of molecular relaxation of poly(propylene oxide) solutions by dielectric relaxation and brillouin scattering

Dielectric relaxation and Brillouin scattering are jointly used in studying molecular relaxation in poly(propylene oxide) (PPO) and its solutions in methylcyclohexane. The dielectric method was applied to the more concentrated (100%, 80%, 60%, by volume) solutions over a wide temperature and frequency range (30 Hz to 8 GHz) in order that the variation in activation energy characteristic of a glass-forming substance could be delineated. The present work extends previous work on the undiluted polymer to higher frequencies so that range of 12 decades in the dielectric loss maximum f_max as a function of temperature is now available. The “Antoine” equation is found to represent the behavior of log f_max, of the bulk concentrated solutions very well. The more dilute (40%, 20%) solutions were studied only in the high-frequency (GHz) region since phase separation occurred at low temperatures. Both the temperature and dilution effects were interpreted in terms of free-volume theory. Brillouin scattering spectra were obtained at several scattering angles and a wide range of temperatures. A maximum in the curve of hypersonic attenuation versus temperature was observed in each polymer solution. The attenuation maximum shifts toward lower temperature upon dilution, in agreement with the dielectric relaxation result. The Brillouin scattering follows different activation parameters and evidences a more rapid process than does the dielectric relaxation. It is speculated that it monitors a secondary or subglass relaxation, due perhaps, to damped torsional oscillations.     

An isotopic effect in the dielectric spectra of Ark. 9/water systems

Dielectric spectra of H₂O and D₂O molecules in the L_α liquid crystalline phase of nonylphenoxy-poly(ethylenoxy)ethanol(Ark. 9)/water lyotropic systems have been investigated by dielectric time domain spectroscopy in the frequency range from 10 MHz to 10 GHz. By fitting the Cole-Cole formula to the dielectric spectra, obtained at different temperatures the dielectric increments, the relaxation times and the distribution parameters have been calculated. A strong retardation of water molecules has been found for the lamellar phase with low water content, i.e. 10 water molecules (H₂O or D₂O) per one Ark. 9 molecule. The relaxation times obtained at room temperature for the light and heavy water are 63 and 93 ps, respectively. It means that the retardation factor for D₂O molecules in the L_α phase is close to 1.5 and higher than that found for pure heavy water (1.25). Any decomposition of the dielectric spectra obtained seems to be unsubstantiated. The temperature dependences of the relaxation times acquired for both kinds of water obey the Arrhenius behaviour.     

Conductance and relaxations in the glassy and rubber states of aqueous poly( vinyl pyrrolidone): A cryofixation medium

The dielectric permittivity and loss of poly(vinyl pyrrolidone), molecular weight 40,000, containing 40% (by weight) water have been measured over the temperature range 77–325 K and frequency range 12 Hz to 0.1 MHz. A prominent relaxation due to rotational diffusion of water molecules in a hydrogen-bonded structure occurs at T < T_g (237 K). The half-width of the dipolar relaxation spectra is 2.27 decades and is temperature independent, which is strikingly different from the corresponding features of pure polymers. It is concluded that H-bonded amorphous solid water persists in the glassy polymer matrix and that the H-bonded structure contains the pyrrolidone side groups of the randomly oriented chain. The relaxation peak at T near T_g is masked by a large dc conductivity which, when expressed in terms of electric modulus, has a spectrum of half-width 1.37 instead of 1.14 decades expected for dc conductivity alone. The contribution from dipolar reorientation in the glass-rubber range of the PVP-H₂O solution is smaller than that in its sub-T_g relaxation.     

Transitions and relaxations in aromatic polymers

Transition and relaxation phenomena in 26 structurally related polyquinoxalines and other aromatic polymers were studied over a temperature range from 70 to 770°K by means of calorimetric, dilatometric, dynamic mechanical, and dielectric techniques. Differential thermal analysis and x-ray data showed these polymers to be essentially amorphous. The lack of crystallinity is attributed to geometric isomerism, resulting in conformational as well as configurational disorder. Calorimetric measurements gave discontinuities in heat capacities ranging from 12 to 54 cal/°C per mole of repeat-unit structures and provided unambiguous assignments of glass transition temperatures of these polymers. Depending upon structure, T_g varied from 489 to 668°K. Thermal expansion curves of annealed bulk polymer samples between 70 and 770°K exhibited only one discontinuity over the entire temperature range, namely at T_g, thus indicating the absence of any motion leading to transitions in the solid state of these polymers. Viscoelastic properties were obtained by means of torsional braid analysis and a longitudinal vibrational apparatus. In a typical case, the dynamic mechanical relaxation spectrum contained three loss maxima. A peak of low amplitude occurring at 483°K was attributed to impurity effects, resulting from endgroups and species of low molecular weight. The second and only major relaxation process occurred at 579°K, in the glass transition interval. A third, weak loss peak of unknown origin was found in the liquid state at 683°K. On the other hand, the dielectric loss curves of various polymers exhibited only one broad and strong absorption maximum at temperatures 30 to 100°K higher (depending upon a particular polymer) than equivalent major mechanical loss peaks. These differences are interpreted from a mechanistic point of view. Major mechanical relaxations occurring in the glass transition interval of these polymers are proposed to result from translational motions.     

Click chemistry‐based synthesis of azo polymers for second‐order nonlinear optics

Four linear polymers containing pendant azo moiety were synthesized through click chemistry for second‐order nonlinear optical study. The polymers were found soluble in most of the polar organic solvents such as tetrahydrofuran (THF), chloroform, and dimethyl formamide (DMF). The polymers showed thermal stability up to 300 °C and glass transition temperatures (T_g) in the range of 120–140 °C. The molecular weights (M_w) of these polymers (measured by gel permeation chromatography) were in the range 37,900–55,000 g/mol. The polymers were found to form optically transparent films by solution casting from THF solution. Order parameters were calculated from UV–vis absorption spectra. The morphology changes in the films after poling were characterized by atomic force microscopy. The angular dependence, temperature dependence, and time dependence of second harmonic generation (SHG) intensity were obtained by using 1064 nm Nd:YAG laser. The SHG intensity remained unchanged up to 95 °C. At room temperature, it remained stable up to 8 days after initial drop of about 14%. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Molecular dynamics of amorphous/crystalline polymer blends studied by broadband dielectric spectroscopy

The molecular dynamics of poly(vinyl acetate), PVAc, and poly(hydroxy butyrate), PHB, as an amorphous/crystalline polymer blend has been investigated using broadband dielectric spectroscopy over wide ranges of frequency (10⁻² to 10⁵ Hz), temperature, and blend composition. Two dielectric relaxation processes were detected for pure PHB at high and low frequency ranges at a given constant temperature above the T_g. These two relaxation peaks are related to the α and α′ of the amorphous and rigid amorphous regions in the sample, respectively. The α′-relaxation process was found to be temperature and composition dependent and related to the constrained amorphous region located between adjacent lamellae inside the lamellar stacks. In addition, the α′-relaxation process behaves as a typical glass relaxation process, i.e., originated from the micro-Brownian cooperative reorientation of highly constraints polymeric segments. The α-relaxation process is related to the amorphous regions located between the lamellar crystals stacks. In the PHB/PVAc blends, only one α-relaxation process has been observed for all measured blends located in the temperature ranges between the T_g’s of the pure components. This last finding suggested that the relaxation processes of the two components are coupled together due to the small difference in the T_g’s (ΔT_g = 35 °C) and the favorable thermodynamics interaction between the two polymer components and consequently less dynamic heterogeneity in the blends. The T_g’s of the blends measured by DSC were followed a linear behavior with composition indicating that the two components are miscible over the entire range of composition. The α′-relaxation process was also observed in the blends of rich PHB content up to 30 wt% PHB. The molecular dynamics of α and α′-relaxation processes were found to be greatly influenced by blending, i.e., the dielectric strength, the peak broadness, and the dielectric loss peak maximum were found to be composition dependent. The dielectric measurements also confirmed the slowing down of the crystallization process of PHB in the blends.     

Pressure dependence of the β molecular relaxation process and dielectric properties of polyvinylidene fluoride

The effects of hydrostatic pressure to 20 kbar on the β molecular relaxation process of polyvinylidene fluoride (PVDF) and on the dielectric properties in the neighborhood of this relaxation have been investigated. This relaxation has a strong influence on the electrical and mechanical properties of PVDF. Pressure causes a large shift to higher temperatures (～ 10K/kbar) of the dielectric relaxation peak and a decrease in the width of the distribution of relaxation times. This slowing down of the relaxation process is discussed in terms of the Vogel–Fulcher equation and related models, and it results from an increase in both the energy barrier to dipolar motion and the reference temperature (T₀) for the kinetic relaxation process which represents the “static” dipolar freezing temperature for the process. The general applicability of the Vogel–Fulcher equation to relaxional processes in polymers and other systems is briefly discussed. The pressure dependence of the dielectric constant both above and below the relaxation peak temperature (T_max) is found to be dominated by the change in polarizability. The effect is larger above T_max because of the relatively large decrease in the dipolar orientational polarizability with pressure.     

Effect of pressure and temperature on chromophore reorientation in a side-chain nonlinear optical polymer

Second harmonic generation (SHG) was used to measure the temperature dependence of the reorientation activation volume of the side-chain copolymer poly(disperse red 1 methacrylate-co-methyl methacrylate) (DR1-MMA). The decay of the SHG signal from poled films of DR1-MMA was recorded at hydrostatic pressures up to 3060 atm and at different temperatures between 25°C below the glass transition temperature (T_g) to 35°C above it. The activation volume, ΔV^*, decreased with increasing temperature. The data suggests that the coupling between chromophore reorientation and the long-range motion of the polymer is stronger for the DR1-MMA side-chain system than in previously measured guest–host systems. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2793–2803, 1998     

Influence of oxycycloaliphatic groups in the relaxation behavior of acrylic polymers

A comparative study on the mechanical and dielectric relaxation behavior of poly(5‐acryloxymethyl‐5‐methyl‐1,3‐dioxacyclohexane) (PAMMD), poly(5‐acryloxymethyl‐5‐ethyl‐1,3‐dioxacyclohexane) (PAMED), and poly(5‐methacryloxymethyl‐5‐ethyl‐1,3‐dioxacyclohexane) (PMAMED) is reported. The isochrones representing the mechanical and dielectric losses present prominent mechanical and dielectric β relaxations located at nearly the same temperature, approximately −80°C at 1 Hz, followed by ostensible glass–rubber or α relaxations centered in the neighborhood of 27, 30, and 125°C for PAMMD, PAMED, and PMAMED, respectively, at the same frequency. The values of the activation energy of the β dielectric relaxations of these polymers lie in the vicinity of 10 kcal mol⁻¹, ∼ 2 kcal mol⁻¹ lower than those corresponding to the mechanical relaxations. As usual, the temperature dependence of the mean‐relaxation times associated with both the dielectric and mechanical α relaxations is described by the Vogel–Fulcher–Tammann–Hesse (VFTH) equation. The dielectric relaxation spectra of PAMED and PAMMD present in the frequency domain, at temperatures slightly higher than T_g, the α and β relaxations at low and high frequencies, respectively. The high conductive contributions to the α relaxation of PMAMED preclude the possibility of isolating the dipolar component of this relaxation in this polymer. Attempts are made to estimate the temperature at which the α and β absorptions merge together to form the αβ relaxation in PAMMD and PAMED. Molecular Dynamics (MD) results, together with a comparative analysis of the spectra of several polymers, lead to the conclusion that flipping motions of the 1,3‐dioxacyclohexane ring may not be exclusively responsible for the β‐prominent relaxations that polymers containing dioxane and cyclohexane pendant groups in their structure present, as it is often assumed. The diffusion coefficient of ionic species, responsible for the high conductivity exhibited by these polymers in the α relaxation, is semiquantitatively calculated using a theory that assumes that this process arises from MWS effects, taking place in the bulk, combined with Nernst–Planckian electrodynamic effects, due to interfacial polarization in the films. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2486–2498, 1999     

On the dielectric glass relaxation process of polymers: Ball-like labels in polystyrene

Ball-like molecules with strong dipoles (labels) were mixed with technical polystyrene (PS168N) in low concentrations (<0.5% wt) and measured dielectrically in the frequency range 10^–2–10⁷ Hz, and the temperature range 100°–135°C (glass relaxation region). The measurements showed that these ball-like molecules relax cooperatively with the polymeric segments with relaxation times lying at the high-frequency tail of the glass process. The activation energy of the main label process is found to be very similar to that of the glass process of the polystyrene segments and also has the same temperature dependence. This finding implies the existence of an additional mode of relaxation in the dielectric spectrum of the glass process of polystyrene (compared to polyisoprene). Considering the different behavior of the ball-like molecules in polystyrene and polyisoprene and the temperature dependence of the half-width of dielectric loss peak in different polymers, we suggest that the polymers could be classified into three classes according to the available dielectric relaxation modes in the glass process. In addition, the label molecules showed a high-frequency local relaxation process. The relaxation strength ratio of the local process (X _local) to the total relaxation strength of the label was found to be dependent on the volume of the label. This phenomenon could supply a new method for the determination of the mean size of the holes (voids) representing the free volume of the host matrix.     

Pulsed NMR study of molecular motion in the diglycidyl ether of bisphenol-A cured with 4,4′-methylenedianiline

The monomeric diglycidyl ether of bisphenol-A cured with methylenedianiline has been studied by pulsed NMR. Values of the proton relaxation times T₁, T_1p, and T₂ have been measured over the temperature range ?160 to 200°C. The system was studied after being fully postcured at 180°C and after being cured at 100°C and at 54°C. The relaxation times are interpreted in terms of molecular motion in the cured resins, i.e., methyl group reorientation, segmental motions, and general molecular motion. The results are compared with those obtained previously by us for the uncured resin. Correlation frequencies for the segmental motions are compared with those obtained from dielectric relaxation and mechanical loss studies. There are at least two principal segmental motions present in the cured system, and the nature of these motions is found to depend on the cure temperature. These effects are discussed in terms of crosslinking and annealing of the system.     

A dielectric study of molecular relaxation in oxidized and chlorinated polyethylenes

A study was made of the dielectric relaxation in polyethylenes rendered dielectrically active through oxidation (0.5–1.7 carbonyls/1000 CH₂) and chlorination (14–22 Cl/1000 CH₂). Both linear and branched polymers were studied. All of the relaxations between the melt and ?196° were studied in the frequency range 10 Hz to 10kHz (100 kHz in the chlorinated samples). In the linear samples a wide range of crystallinities was studied (55% in quenched specimens to 95% in extended-chain specimens obtained by crystallization at 5 kbar). As is consistent with its being a crystalline process, the α peak was found to discontinously disappear on melting of the samples and reappear on recrystallizing on cooling. The disappearance of the smaller crystals before the larger ones appeared to be evident in the isothermal loss versus frequency curves. The relaxation strength of the α process increases with crystallinity. The measured relaxation strength is less than that expected on the basis of direct proportionality to the crystalline fraction with full contribution of all dipoles in the crystalline material. However, the intensity is not sufficiently low for the process to be interpreted in terms of reorientation of localized conformational defects in the crystal. The variation of intensity with crystallinity is best interpreted in terms of full participation of crystalline dipoles but with selective partitioning of both carbonyls and chlorines favoring the amorphous domains. A strong correlation of the α loss peak location (T_max at constant frequency or log f_max at constant T) with crystallinity for both carbonyl and chlorine containing polymers was found. This variation is interpreted in terms of chain rotations in the crystal where the activation free energy depends on crystal thickness. The dependence of log f_max and T_max on lamellar thickness as well as a comparison with the loss peaks of ketones dissolved in parafins indicates that the chain rotation is not rigid and is accompanied by twisting as the rotation propagates through the crystal. In agreement with previous studies the β process is found to be strong only in the branched polymers but can be detected in the chlorinated linear polymer. The β process was resolved from the α in the branched samples by curve fitting and its activation parameters determined. The γ relaxation peak in oxidized polymers including its high asymmetry (low-temperature tail) and increasing ε_max with increasing frequency and temperature when plotted isochronally can be interpreted in terms of a simple nearly symmetrical relaxation time spectrum that narrows with increasing temperature. No increase in relaxation strength with temperature was found. The chlorinated polymers behave similarly but appear to have some Boltzmann enhancement (450–750 cal/mole) of relaxation strength with temperature. The dependence of relaxation strength on crystallinity indicates that the process is an amorphous one. Further, no evidence of relaxation peak shape changes with crystallinity that could be interpreted in terms of a crystalline component in addition to the amorphous one was found. The comparison of the γ relaxation strength with that expected on the basis of full participation of amorphous dipoles indicates that only a small fraction (～10% in oxidized linear polymers) of them are involved in the relaxation. Thus it would seem that a glass–rubber transition interpretation is not indicated but rather a localized chain motion. It is suggested that the γ process, including its intensity, width, and activation parameters, can be interpreted in terms of an (unspecified) localized conformational (bond rotation) motion that is perturbed by differing local packing environments. The thermal expansion lessens the effects of variations in packing and leads to narrowing with increasing temperature. The conformational motion itself leads to increase in thermal expansion and hence a transition in the latter property. Some previously proposed localized amorphous phase conformational motions appear to be suitable candidates for the bond rotation motion. A weak relaxation peak found at temperatures below the γ and at 10 kHz may possibly be the dielectric analog of the δ cryogenic peak found previously mechanically at lower frequencies.     

Systematic Dielectric and NMR Study of the Ionic Liquid 1‐Alkyl‐3‐Methyl Imidazolium

The dynamic behaviors of ionic liquid samples consisting of a series of 1‐alkyl‐3‐methylimidazolium cations and various counteranionic species are investigated systematically over a wide frequency range from 1 MHz to 20 GHz at room temperature using dielectric relaxation (DR) and nuclear magnetic resonance (NMR) spectroscopies. DR spectra for the ionic liquids are reasonably deconvoluted into two or three relaxation modes. The slowest relaxation times are strongly dependent upon sample viscosity and cation size, whereas the relaxation times of other modes are almost independent of these factors. We attribute the two slower relaxation modes to the rotational relaxation modes of the dipolar cations because the correlation times of the cations evaluated using longitudinal relaxation time (T₁ ¹³C NMR) measurements corresponded to the dielectric relaxation times. On the other hand, the fastest relaxation mode is presumably related to the inter‐ion motions of ion‐pairs formed between cationic and anionic species. In the case of the ionic liquid bis(trifluoromethanesulfonyl)imide, the system shows marked dielectric relaxation behavior due to rotational motion of dipolar anionic species in addition to the relaxation modes attributed to the dipolar cations.     

General properties of secondary relaxations in polymers as determined by the thermally stimulated current method

The method of thermally stimulated current (TSC) has been used to study the low-temperature dielectric β relaxations of several polymers including especially poly(vinyl chloride), poly(vinyl acetate), polyamide 6, 6,6,poly(t-butyl acrylate), poly(methyl methacrylate), poly(ethyl methacrylate), poly(phenyl methacrylate), and poly(t-butyl methacrylate). The distribution characteristics of the relaxation processes have been determined from the corresponding TSC peaks by a fractional polarization technique which consists of applying the electric field in several discrete steps during a slow cooling. Several common features have been found in all the polymers investigated: the β peaks are characterized by a distribution of relaxation times resulting from a distribution in activation energy and this distribution is quasisymmetrical and continuous. These facts are in agreement with the hypothesis of a relaxation involving local motions of small polar groups undergoing various interactions with the environment. Some discrepancy remains, however, between our calculated values of the mean activation energy and those obtained from the dielectric loss.     

Positron annihilation studies of chromophore-doped polymers

Doppler-broadening energy spectra and positron annihilation lifetime have been measured as a function of positron implantation energy in pure and chromophore Disperse Red 1 (DR1)-doped poly(methyl methacrylate) (PMMA) polymers. In pure PMMA, the S parameter increases at very short range (<0.02 μm) from the surface to the bulk, while the S parameter of doped PMMA varies with a decrease from a depth of >0.02 μm to about 0.5 μm after an increase, a short distance from the surface. The o-Ps lifetime of the polymers is found to increase from the bulk to the surface, which indicates that the hole size expands near the surface. The o-Ps lifetime distribution becomes broader near the surface. The change of the o-Ps intensity shows the same trend as the change of the S parameter. These results are interpreted as a gradient of DR1 concentration in PMMA, as a function of the depth from the surface to the bulk in the chromophore-doped polymers.     

Experimental characterization of hexatic smectic phases through electro-optic studies and dielectric relaxation spectroscopy

The electro-optic and complex dielectric behaviour of an antiferroelectric liquid crystal 4-(1-methylheptyloxycarbonyl)phenyl 4′-(n-butanoyloxyprop-1-oxy)biphenyl-4-carboxylate, having chiral SmC_A* and hexatic smectic phases, have been investigated. Complex dielectric permittivities were measured as a function of frequency, d.c. bias field and temperature. Spontaneous polarization was measured by the current reversal technique; tilt angle was measured under a polarizing microscope using a low frequency electric field. The electro-optic properties and dielectric behaviour of the material are compared with results obtained by DSC and polarizing optical microscopy. Dielectric relaxation processes in SmC_A* and hexatic smectic phases were determined. The dielectric strength at the SmC_A* to hexatic smectic phase transition is discussed in terms of coupling between the long range bond orientational order and smectic C director. It seems from the results of spontaneous polarization and dielectric relaxation spectroscopy that the material might possess an additional phase between the SmC_A* and hexatic smectic I* phases.