Structure-property relationship of polyurethane ionomer

Polyurethane (PU) ionomers were prepared using various types of polyol (PTAd, PCL, PTMG, and PPG) and isocyanate (MDI, HDI, and IPDI), together with different extender (DMPA) contents, degree of neutralization, and number average molecular weight (M _n) of polyol. Modulus (E), strength (_b), and glass transition temperature (T _g) significantly increased with the increased amount of extender and extender neutralization. Among three of the iocyanate used, PU from MDI gave the highest modulus, strength, andT _g. With regard to theM _n of PTAd (600, 1000, 2000), PU from PTAd 600M _n gave the highest modulus, strength, andT _g, due probably to the highest hard segment content and phase mixing. On the other hand, PU from PTAd 2000M _n gave significantly improved strength over PTAd 1000M _n, and the highest elongation. The results were interpreted in terms of soft-segment crystallization, and soft-hard phase separation, which was concluded from the lowered softT _g.     

Studies on thermotropic liquid crystalline polyurethanes. III. Synthesis and properties of polyurethane elastomers by using various mesogenic units as chain extender

Four series of thermotropic polyurethane elastomers (TPUEs) were synthesized in this study. The hard segments were formed by using 4,4′-methylenedicyclohexyl diisocyanate (H₁₂MDI) reacted with various mesogenic units, such as benzene-1,4-di(4-iminophenoxy-n-hexanol), benzene-1,4-di(4-iminophenol), and 3,3′-(4,4′-biphenylene)dipropanol, which also acted as the chain extender. Poly(oxytetramethylene)glycols (PTMEGs), PTMEG-2000 (M_n 2,000) and PTMEG-1000 (M_n 1,000) were used as a soft segment. The structures of all synthesized thermotropic liquid crystalline polyurethanes (TLCPUs) were characterized by FTIR spectroscopy. The effects of mesogenic units on the LC properties and elastic behaviors of LCPUs were studied. It was difficult to show LC behaviors for the PU elastomers derived from the mesogenic units with a lower aspect ratio, such as 3,3′-(4,4′-biphenylene)dipropanol, or the long soft segments, PTMEG-2000. In addition, these PU elastomers show better elastic properties by using a higher aspect ratio mesogenic unit as the chain extender, such as benzene-1,4-di(4-iminophenoxy-n-hexanol and benzene-1,4-di(4-imino-phenol)). The thermal properties were investigated by DSC measurements, thermal optical polarized microscopy, wide angle X-ray diffraction, dynamic mechanical analysis, and thermogravimetric analysis. The mechanical properties were measured by a tensilemeter. © 1996 John Wiley & Sons, Inc.     

Polyurethane Ionomers from Cycloaliphatic Diisocyanate and Polytetramethylene Glycol

Abstract

Segmented polyurethane (PU) ionomers were prepared from cycloaliphatic diisocyanate [methylene bis(4-cyclohexyl isocyanate) (H₁₂MDI) and isophoron diisocyanate (IPDI)] and polytetramethylene glycol (PTMG) by using an anionic-type chain extender, viz., dimethylol propionic acid (DMPA). The effect of ionic content and butanediol (BD) on the state of dispersion and physical properties of emulsion-cast film was determined using Autosizer, transmission electron microscopy (TEM), Instron, and Rheovibron. With increased incorporations of DMPA in PU, particle size of emulsion decreased asymptotically, tensile modulus and strength increased, and the glass transition temperature (T _g) moved toward the higher temperature. On the other hand, with increased incorporation of BD in PU, particle size of emulsion, tensile modulus, and strength of the emulsion cast film increased, and the major transition of soft segment moved toward higher temperature. With regard to the structural effect of the isocyanate, H₁₂MDI gave finer dispersion and better mechanical properties over IPDI.     

Structure analysis of polyether-based thermoplastic polyurethane elastomers by FTIR, 1H NMR and 13C NMR

One kind of unknown structure sequence and composition ratio of thermoplastic polyurethane elastomers were characterized by nuclear magnetic resonance spectroscopy, Fourier transformed infrared spectroscopy, and gel permeation chromatography (GPC). The results showed that the polyurethane (PU) was obtained from poly(tetramethylene glycol) (PTMG) as soft segment, 1,4-butanediol (BDO) as chain extender, and 4,4′-methylenediphenyl diisocyanate (MDI) as hard segment. Furthermore, the composition ratio of MDI:PTMG:BDO was 2.07:1.22:1.00. At last, the molecular weight of PU was determined by GPC, and the number average molecular weight (M_n) and weight average molecular weight (M_w) are 63,300 and 133,800?g?mol^?1, respectively.     

Preparation of poly(n‐butyl acrylate)‐b‐polystyrene particles by emulsifier‐free,organotellurium‐mediated living radical emulsion polymerization (emulsion TERP)

We have successfully demonstrated the preparation of poly(n‐butyl acrylate)‐b‐polystyrene particles without any coagulation by two‐step emulsifier‐free, organotellurium‐mediated living radical emulsion polymerization (emulsion TERP) using poly(methacrylic acid) (PMAA)–methyltellanyl (TeMe) (PMAA₃₀‐TeMe) (degree of polymerization of PMAA, 30) and 4,4′‐azobis(4‐cyanovaleric acid) (V‐501). The final particle size was ～30 nm and second particle nucleation was not observed throughout the polymerization. M_n increased linearly in both steps with conversion and blocking efficiency was ～75%. PDI was improved by increasing radical entry frequency into each polymer particle due to an increase of the polymerization temperature. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Polymer grafting onto polyurethane backbone via Diels–Alder reaction

The aliphatic polyurethane with pendant anthracene moieties (PU‐anthracene) was prepared from polycondensation of anthracen‐9‐yl methyl 3‐hydroxy‐2‐(hydroxymethyl)‐2‐methylpropanoate (anthracene diol), 1 with hexamethylenediisocyanate in the presence of dibutyltindilaurate in CH₂Cl₂ at room temperature for 10 days. Thereafter, the PU‐anthracene (M_n,GPC = 12,900 g/mol, M_w/M_n = 1.87, relative to PS standards) was clicked with a linear α‐furan protected‐maleimide terminated‐poly(methyl methacrylate) (PMMA‐MI) (M_n,GPC = 2500 g/mol, M_w/M_n = 1.33), or ‐poly(ethylene glycol) (PEG‐MI) (M_n,GPC = 550 g/mol, M_w/M_n = 1.09), to result in well‐defined PU‐graft copolymers, PU‐g‐PMMA (M_n,GPC = 23800 g/mol, M_w/M_n = 1.65, relative to PS standards) or PU‐g‐PEG (M_n,GPC = 11,600 g/mol, M_w/M_n = 1.45, relative to PS standards) using Diels–Alder reaction in dioxane/toluene at 105 °C. The Diels–Alder grafting efficiencies were found to be over 93–99% using UV spectroscopy. Moreover, the structural analyses and the thermal transitions of all copolymers were determined via ¹H NMR and DSC, respectively. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 521–527     

Power law of nucleation rate of folded-chain single crystals of polyethylene

The number-average molecular weight (M _n) dependence of the primary nucleation rate (I) of polyethylene (PE) folded-chain single crystals was studied in the ordered phase. We observed that the M _n dependence of I is mainly controlled by the diffusion process of polymer chains within the interface between a nucleus and the melt and/or within the nucleus. The results show that I decreases with increasing M _n and follows a power law I∝M _n ^−2.3 for the ordered phase. It is named the power law of the nucleation rate. In a previous article we showed that for the disordered phase I∝M _n ⁻¹. In this article, we concluded that I decreases with increasing M _n and follows a universal power law, I∝M _n ^−H for both ordered and disordered phases. The power H depends on the degree of order of the crystalline phase, which is related to the morphology. Received: 13 September 2000 Accepted: 15 November 2000     

The synthesis and morphology of grafted semiinterpenetrating polymer networks on the basis of functional prepolymers

Semi-IPNs on the basis of PU prepolymers with carboxylic groups and methacrylic copolymers with tertiary amine groups were synthesized. The influence of the functional group content and of the M_n of polymer components, as well as their ratio, on the morphology and mechanical properties were investigated. The miscibility in the systems was estimated by differential scanning calorimetry (DSC) and by scanning electron microscopy (SEM). The miscibility of components was increased by augmenting the content of the functional groups. By varying the ratio of components, the highest miscibility was found at the isoelectric ratio of functional groups. However, all the investigated IPNs were two-phase systems, due to the segmented structure of PU prepolymers. The lowering of M_n values of the starting components did not improve their compatibility. The mechanical properties of semi-IPNs changed with the increased concentration of functional groups in a way that is typical for ionomers. By physical interactions between functional groups, Young's modulus was most influenced, while the M_n of the polymethacrylic component influenced the tensile strength of IPNs. The compatibility between PU hard segments and the polymethacrylic component found in our experiments led us to the conclusion that the preparation of IPNs of finer morphology would be possible by using PU prepolymers with shorter soft segments. © 1996 John Wiley & Sons, Inc.     

Emulsion polymerization of vinyl acetate using iodine‐transfer and RAFT radical polymerizations

This study deals with control of the molecular weight and molecular weight distribution of poly(vinyl acetate) by iodine‐transfer radical polymerization and reversible addition‐fragmentation transfer (RAFT) emulsion polymerizations as the first example. Emulsion polymerization using ethyl iodoacetate as the chain transfer agent more closely approximated the theoretical molecular weights than did the free radical polymerization. Although ¹H NMR spectra indicated that the peaks of α‐ and ω‐terminal groups were observed, the molecular weight distributions show a relatively broad range (M_w/M_n = 2.2–4.0). On the other hand, RAFT polymerizations revealed that the dithiocarbamate 7 is an excellent candidate to control the polymer molecular weight (M_n = 9.1 × 10³, M_w/M_n = 1.48), more so than xanthate 1 (M_n = 10.0 × 10³, M_w/M_n = 1.89) under same condition, with accompanied stable emulsions produced. In the M_n versus conversion plot, M_n increased linearly as a function of conversion. We also performed seed‐emulsion polymerization using poly(nonamethylene L ‐tartrate) as the chiral polyester seed to fabricate emulsions with core‐shell structures. The control of polymer molecular weight and emulsion stability, as well as stereoregularity, is also discussed. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Morphology of polyurethanes with triol monomer crosslinked on hard segments

Polyester‐based polyurethanes containing ≈60 wt % of polyester were synthesized from low molecular weight polyester (M_n ≈2000) and 4,4′‐methylene bis(phenyl isocyanate) (MDI), with butanediol as a chain extender and glycerol as a crosslinker. The triol crosslinker was used in substitution for the 1,4‐butanediol chain extender; thus, the crosslinker was chemical bonded to the hard segments of polyurethane. The morphologies of these polyurethanes were studied by differential scanning calorimetry (DSC), small‐angle X‐ray scattering (SAXS), TMA (thermal mechanical analysis), and FTIR (Fourier transform infrared spectroscopy). Owing to the highly steric hindrance, the presence of triol crosslinker in the hard segments resulted in a decrease in the aggregation of hard segments through hydrogen bonding. The experimental results revealed that the degree of phase segregation of soft and hard segments decreased with increasing the triol crosslinker content in the hard segments. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2673–2681, 1999     

Semibatch emulsion polymerization of methyl methacrylate using different polyurethane particles

Aqueous acrylic‐polyurethane (AC–PU) hybrid emulsions were prepared by semibatch emulsion polymerization of methyl methacrylate (MMA) in the presence of four polyurethane (PU) dispersions. The PU dispersions were synthesized with isophorone diisocyanate (IPDI), 1000 and 2000 molecular weight (MW) poly(neopentyl) adipate, 1000 MW polytetramethyleneetherglycol, butanediol (BD), and dimethylol propionic acid (DMPA). MMA was added in the monomer emulsion feed. We studied the effect of the use of different PU seed particles on the rate of polymerization, the particle size and distribution, the number of particles, and the average number of radicals per particle. The PU rigidity was controlled by varying the polyol chemical structure, the polyol MW (M_n), and by adding BD. The monomer feed rate was varied to study its influence on the process. It was observed that the PU particles that had been prepared with a higher MW polyol swelled better with MMA before the monomer‐starved conditions occurred. There seemed to be no significant discrepancies between the series with different PU seeds in the monomer‐starved conditions. The overall conversion depended on the monomer addition rate, and the polymerization rate acquired a constant value that was comparable to the value of the monomer addition rate. The instantaneous conversion increased slightly. The average particle size increased, and the total particle number in the reactor was constant and similar to the number of PU particles in the initial charge. The average number of radicals per particle increased. The differences between the system with a constant particle number and average number of radicals per particle and the system with a fixed radical concentration are discussed. The semibatch emulsion polymerization of MMA in the presence of PU particles studied was better compared to the system with a fixed radical concentration. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 844–858, 2005     

Thermal properties of solvolysis lignin-derived polyurethanes

Thermal properties of polyurethane (PU) films prepared from solvolysis lignin (SL), polyethylene glycol (PEG) and diphenylmethane diisocyanate (MDI) were examined by differential scanning calorimetry and thermogravimetry. In the SL—PEG—MDI system, the SL content, the molecular weight (M_n) of PEG and the NCO/OH ratio were changed in order to control the thermal properties. Glass transition temperatures (T_g's) of the prepared PU's were dependent on the SL content, the M_n of PEG and the NCO/OH ratio. However, the T_g of PU was significantly influenced by the SL content: the increment of T_g was ca. 150 K when the SL content in PEG increased from 0 to ca. 50%. The decomposition of the PU's was markedly dependent on the content of SL. Other factors, such as the NCO/OH ratio and the M_n of PEG, are less dominant compared with the SL content. This fact suggests that the dissociation between the isocyanate groups and the phenolic OH groups in SL may be the major factor in the whole process of the thermal decomposition of the PU containing SL     

Pyrene fluorescence measurements of metastable oil droplets in surfactant-free oil-in-water emulsions

 The fluorescence behavior of pyrene in oil droplets of a surfactant-free oil-in-water emulsion was studied for benzene, fluorobenzene, n-hexane and cyclohexane droplets in water. The excimer–monomer fluorescence ratio immediately after sonication, I _E/I _M(0), of the benzene/water emulsion was 8–10 times larger than for the benzene solution. The ratio I _E/I _M(t) increased in the first 10–20 min before it decreased to zero. Similar behavior was observed for the fluorobenzene/water emulsion, while I _E/I _M(0) for emulsions with n-hexane and cyclohexane was smaller than for benzene and fluorobenzene/water emulsions. I _E/I _M(t) hardly changed with time for the n-hexane and cyclohexane/water emulsions. This different behavior was attributed to the increased solubility of nanometer-size droplets with benzene and fluorobenzene. Received: 20 June 2001 Accepted: 19 April 2001     

Controlling grafting density and side chain length in poly(n‐butyl acrylate) by ATRP copolymerization of macromonomers

Atom transfer radical polymerization (ATRP) was used for the preparation and subsequent copolymerization of two acryloyl‐terminated poly(n‐butyl acrylate) macromonomers with different degrees of polymerization (DP_nBA = 25 and 42). Homopolymerization of the higher molecular weight macromonomer ( MM1 ; PnBA₄₂‐A, M_n = 5600, DP_MM = 42, M_w/M_n = 1.18) resulted in preparation of a densely grafted polymer with a narrow molecular weight distribution (M_w/M_n = 1.14), but with the limited degree of polymerization DP = 12. The ultimate degree of homopolymerization for the lower molecular weight macromonomer ( MM2 ; PnBA₂₅‐A, M_n = 3400, DP_MM = 25, M_w/M_n = 1.20) was higher, and DP increased from 12 to 22. The limited DP could be because of progressively increasing steric congestion for macromonomers in approaching the growing chain ends of densely grafted polymers. When MMs were copolymerized with nBA, the reactivity of MM was nearly the same as that of nBA monomer irrespective of the differences in the degree of polymerization of the MMs and the initial molar ratio of nBA to MM. Well‐defined graft polymers with different lengths of backbone and side chains, and different graft density were successfully prepared by “grafting through” ATRP. Tadpole‐shaped and dumbbell‐shaped graft polymers were also synthesized by ATRP. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5454–5467, 2006     

Aqueous Dispersion of Polyurethane Anionomer from Aliphatic Diisocyanates and Poly(Hexamethylene Carbonate) Diol

Abstract

Water dispersible polyurethanes (PUs) were prepared from poly(hexamethylene carbonate) (PHC) diol, isophorone diisocyanates (IPDI), hexamethylene diisocyanate (HDI), and dimethylolpropionic acid (DMPA) as latent anionic sites. After neutralization of the carboxyl group from the DMPA unit with triethylamine (TEA), the PU anionomers were dispersed by adding water, following by crosslinking using triethylenetetramine (TETA). The particle size of the dispersion decreased with the content of DMPA and increased with HDI in the HDI-IPDI system, and it exhibited a minimum when the number-average molecular weight (M _n) of the prepolymer was 3000 and 4500, respectively. PUs with a higher content of hard segments from DMPA or TETA, or with a higher content of IPDI rather than HDI, had higher tensile moduli and storage moduli at room temperature. Ultimate tensile properties increased with an increase of the prepolymer molecular weight and the DMPA and HDI content.     

Effects of altered reaction conditions on the synthesis of polyurethane-poly(2,2,2-trifluoroethyl methacrylate) triblock copolymer aqueous dispersion

Polyurethane-poly(2,2,2-trifluoroethyl methacrylate) (PU-PTFEMA) triblock copolymer aqueous dispersions were synthesized by three-step polymerization. In the first step, polyurethane prepolymers (PU) based on 2,4-toluene diisocyanate (TDI), polyether binary alcohol (N₂₂₀), α,α-dimethylol propionic acid (DMPA), hydroxypropyl acrylic acid (HPA), and butanediol (BDO) were prepared with butanediol as the chain extender and methylethylketon as solvent. The next step involved neutralization and dispersion in water, where prepolymers were neutralised by the addition of triethylamine (TEA). The last step was the seeded emulsion polymerization, where PU emulsion was used as seed, kalium persulfate (KPS) as initiator and 2,2,2-trifluoroethyl methacrylate (TFEMA) as comonomer. Factors influencing the synthesis of PU-PTFEMA copolymer aqueous dispersion were studied. Experimental data indicate that factors influencing the synthesis of PU-PTFEMA copolymer aqueous dispersion mainly involve reaction temperature, reaction time, the concentration of initiator, DMPA content, TFEMA content. Rotational viscometer and dynamic light scattering (DLS) were used to characterize the properties of copolymer aqueous dispersion.     

Polymer degradation during radiation-induced emulsion polymerization of styrene

Styrene was polymerized in emulsion with initiation by γ-rays at a dose rate of 0.6 Mrad/hr. Polymerization rates were as expected from previous reports by others. No branching or crosslinking was detectable, and the M _w/M _n ratio of the polystyrene did not change significantly during the course of the polymerization reaction. The molecular weight of the product polymer decreased with increasing conversion, in contrast to the behavior of chemically initiated emulsion polymerizations. Monomer-free polystyrene does not degrade under the same radiation conditions, and the progressive decrease of polymer molecular weight with conversion is shown to result from the presence of monomer.     

Study of Phase Separation of Poly(N-isopropylacrylamide-co-styrene) Aqueous Solutions with Rayleigh Scattering Technique

A thermally sensitive copolymer, poly(N‐isopropylacrylamide‐co‐styrene) [P(NIPAM‐co‐St)] (M_n?9.5×10⁵ g/mol and M_w/M_n?1.51) was synthesized by soap‐free emulsion polymerization. The phase separation of the copolymer in water was investigated by Rayleigh scattering (RS) technique. The RS spectra revealed the transition of molecular conformation and the aggregation of molecular chains in the course of phase separation. The coil‐to‐globule and globule‐to‐coil transitions of P(NIPAM‐co‐St) chains were found in one heating‐and‐cooling cycle. By means of Avrami formula, apparent activation energy of phase separation of P(NIPAM‐co‐St) aqueous solutions was estimated. Moreover, a model was proposed to describe the phase separation process.     

Effects of molecular weight of nitrocellulose on structure and properties of polyurethane/nitrocellulose IPNs

Semi‐interpenetrating polymer network (semi‐IPN) coatings were prepared by using castor oil‐based polyurethane (PU) and nitrocellulose (NC) with various viscosity‐average molecular weights (M_η) from 6 × 10⁴ to 42 × 10⁴, and coated on a regenerated cellulose (RC) film to obtain water‐resistant film. The PU/NC coatings and coated films, which were cured at 80°C for 5 min and 2 min, respectively, were investigated by infrared (IR) and ultraviolet (UV) spectroscopy, X‐ray diffraction, swelling test, strength test, dynamic mechanical thermal analysis (DMTA), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The results show that the crosslink densities of the PU/NC semi‐IPNs were smaller than that of pure PU, and decreased with the decrease of M_η of nitrocellulose (NC M_η), indicating NC molecules cohered intimately with PU, and hindered the PU network formation. The physical and mechanical properties of the films coated with PU/NC coatings were significantly improved. With the increase of NC M_η, the strength and thermal stability of the coated films increased, but the pliability, water resistivity, and optical transmission decreased slowly. The PU/NC coating with low NC M_η more readily penetrated into the RC film, and reacted with cellulose, resulting in a strong interfacial bonding and dense surface caused by intimate blend of PU/NC in the coated films. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1623–1631, 1999     

Influence of molecular weight on the phase behaviors of comb‐like polymers with long n‐alkyl side chains based on mesogen‐jacketed liquid crystalline polymers

A series of comb‐like polymers, poly{2,5‐bis[(4‐octadecyloxyphenyl)oxycarbonyl]‐styrenes{ (P‐OC18s) with different molecular weights (M_n) and low molecular weight distributions have been successfully synthesized via atom transfer radical polymerization. The phase behaviors have been investigated by a combination of techniques including differential scanning calorimetry, polarized optical microscopy, wide‐angle X‐ray diffraction, and temperature‐variable FTIR spectroscopy. One hand, phase behaviors of the alkyl tails were strongly influenced by the mesogens of polymers, leading to the poor packing of the alkyl tails and the low melting. The other hand, the liquid crystalline phase structures of polymers were found to be strongly M_n dependent. The samples with M_n ≤ 4.6 × 10⁴ formed a smectic phase in low temperature and an isotropic phase in high temperature. The samples with M_n ≥ 5.2 × 10⁴ displayed a reentrant isotropic phase, which was separating the smectic phase and columnar nematic phase. Meantime, the experiment results showed that the glass temperature and the transition temperature from smectic phase to isotropic phase both slightly increased with the increase of M_nS; however, the transition temperature from isotropic phase to columnar phase sharply decreased with the M_nS improved. The reappearance of isotropic phase is due to the competing between the driving force of the enthalpy and the driving force of the entropy. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013