Melting and internal motion in highly alternating copolymers of ethylene and carbon monoxide

The melting point of the 1:1 copolymer of ethylene and CO is 244°C. It falls rapidly as the percent CO is reduced indicating that the heat and entropy of fusion are 0.60 kcal and 1.15 e.u./mol of chain atoms, respectively. These are lower than the values for polyethylene. Dynamic mechanical measurements showed loss peaks at ?100° and 25°C. The low temperature γ-relaxation which is also seen in dielectric data appears to be a local mode relaxation with an activation energy of about 12 kcal/mol. The room temperature relaxation is associated with a large decrease in the modulus and a large increase in the dielectric constant. It is probable that the low entropy of fusion is due in part to extensive motion in the crystal.     

Thermostimulated depolarization currents in thermorheologically simple materials

A theory is presented which makes possible the calculation of the dielectric parameters for a distributed dipole relaxation from thermostimulated depolarization current (TDC) data. The theory is applicable to dielectrics which obey the time–temperature superposition principle, i.e., for thermorheologically simple materials. The shift factor, the activation energy, the dielectric relaxation strength, the density of the isothermal displacement current, and the distribution function of relaxation times of the β relaxation in poly(methyl methacrylate) are calculated. The TDC investigations were carried out over the temperature range of ?136 to 90°C. The values for the activation energy U = 26.4 kcal/mole and the dielectric relaxation strength Δ_?β = 2 are in good agreement with values obtained from dynamic measurements. A criterion for checking the validity of the time–temperature superposition principle by TDC is suggested.     

Thermal decomposition of sodium azide

The thermal decomposition of sodium azide has been investigated in the temperature range 240–365°C. Three values for the activation energy, 37.0, 59.0 and 14 kcal mol^?1 have been obtained depending on the temperature range of study. The mechanism of decomposition seems to involve excited azide ions (through internal conversion) and excitations. The activation energy of 14 kcal mol^?1 appears to be associated with the promotion of electron in the presence of sodium metal.     

Internal motions in an alternating copolymer of ethylene and tetrafluoroethylene

Internal motions in an alternating copolymer of ethylene and tetrafluoroethylene were investigated by dynamic mechanical and dielectric measurements and by nuclear magnetic resonance. At 1 Hz the α, β, and γ relaxations were observed at 110, ?25, and ?120°C in a quenched sample. The activation energy was 76 kcal/mole for the α relaxation and 10.6 kcal/mole for the γ relaxation. These relaxations are attributed to the motion of long and short segments in the amorphous regions, respectively. The β relaxation, which was observed only in the dynamic mechanical experiments, appears to occur in the crystalline regions. The copolymer is isomeric with poly(vinylidene fluoride), but it has a higher melting point and a much lower dielectric loss.     

Synthesis and Structures of Polyphenylphenanthrenes

1,2,3,4,5,6,7,8-Octaphenylphenanthrene ( 4 ) and decaphenylphenanthrene ( 5 ) were prepared by very short syntheses (two or three steps) from tetraphenylfuran and polybrominated benzene derivatives. The X-ray structures of compounds 4 and 5 show them to be quite crowded, with the phenanthrene cores twisted by about 40° due to the clash of the C4 and C5 phenyl groups. Compound 4 was resolved by chromatography on a chiral support, and its free energy of activation for racemization was determined to be 24.6 kcal mol⁻¹ at 40 °C. Computational studies indicate that compound 5 has a racemization barrier approximately 6 kcal mol⁻¹ lower than 4 , and thus 5 would not be configurationally stable at room temperature.     

Influence of oxycycloaliphatic groups in the relaxation behavior of acrylic polymers

A comparative study on the mechanical and dielectric relaxation behavior of poly(5‐acryloxymethyl‐5‐methyl‐1,3‐dioxacyclohexane) (PAMMD), poly(5‐acryloxymethyl‐5‐ethyl‐1,3‐dioxacyclohexane) (PAMED), and poly(5‐methacryloxymethyl‐5‐ethyl‐1,3‐dioxacyclohexane) (PMAMED) is reported. The isochrones representing the mechanical and dielectric losses present prominent mechanical and dielectric β relaxations located at nearly the same temperature, approximately −80°C at 1 Hz, followed by ostensible glass–rubber or α relaxations centered in the neighborhood of 27, 30, and 125°C for PAMMD, PAMED, and PMAMED, respectively, at the same frequency. The values of the activation energy of the β dielectric relaxations of these polymers lie in the vicinity of 10 kcal mol⁻¹, ∼ 2 kcal mol⁻¹ lower than those corresponding to the mechanical relaxations. As usual, the temperature dependence of the mean‐relaxation times associated with both the dielectric and mechanical α relaxations is described by the Vogel–Fulcher–Tammann–Hesse (VFTH) equation. The dielectric relaxation spectra of PAMED and PAMMD present in the frequency domain, at temperatures slightly higher than T_g, the α and β relaxations at low and high frequencies, respectively. The high conductive contributions to the α relaxation of PMAMED preclude the possibility of isolating the dipolar component of this relaxation in this polymer. Attempts are made to estimate the temperature at which the α and β absorptions merge together to form the αβ relaxation in PAMMD and PAMED. Molecular Dynamics (MD) results, together with a comparative analysis of the spectra of several polymers, lead to the conclusion that flipping motions of the 1,3‐dioxacyclohexane ring may not be exclusively responsible for the β‐prominent relaxations that polymers containing dioxane and cyclohexane pendant groups in their structure present, as it is often assumed. The diffusion coefficient of ionic species, responsible for the high conductivity exhibited by these polymers in the α relaxation, is semiquantitatively calculated using a theory that assumes that this process arises from MWS effects, taking place in the bulk, combined with Nernst–Planckian electrodynamic effects, due to interfacial polarization in the films. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2486–2498, 1999     

Dielectric relaxation in styrene-related polymers at low temperatures

The complex dielectric constants ?^* = ?′ ? j?″ of each of several members of a system of copolymers of 4-chlorostyrene and 4-methylstyrene have been measured from 1.6°K to 300°K and from 0.1 kHz to 20 kHz. The principal experimental findings are: the strength of the relaxation process which occurs near 50°K at 1 kHz varies linearly with changing copolymer composition; both the apparent activation energy (H = 2.7 ± 0.7 kcal/mole) and the shape of the relaxation curve are independent of the composition variable and of the temperature (or frequency) within the ranges studied; and the ratio of the relaxation strength of poly-4-methylstyrene to that of poly-4-chlorostyrene in the 50°K process is about 25 times the corresponding ratio for the primary relaxation process that occurs in the neighborhood of the glass-transition temperature. These findings suggest that in the 50°K process the phenyl groups relax independently of one another; that the apparent activation energy and the shape of the relaxation spectrum are determined primarily by the nature of the intrachain forces; and that the strength of the relaxation process depends primarily on effects of intermolecular forces that are governed by the molar “free volume” of the copolymers.     

Degradation studies of some polyesters and polycarbonates—2. Polylactide: Degradation under isothermal conditions,thermal degradation mechanism and photolysis of the polymer

The thermal degradation of polylactide has been studied at several temperatures in the range 230–440°C and the variation of product distribution with temperature has been examined. From experiments at 240–270°C, an energy of activation of 28·5 kcal mol^?1 (119 kJ mol^?1) has been calculated. Mass spectra have been obtained for polylactide and for the cold ring fraction of degradation products in TV A experiments. Both lactide and polylactide have also been heated under closed system conditions and the products have been identified.A mechanism is presented for the thermal degradation, based upon a hydroxyl end-initiated ester interchange process giving cyclic oligomers, lactide, acetaldehyde and carbon monoxide, together with a series of reactions at somewhat higher temperatures dependent upon chain homolysis, giving the same products and also carbon dioxide and methylketene.The photolysis of polylactide at 30°C, using the medium pressure mercury lamp, has been briefly examined.     

Structure and side-chain interactions in poly(δ-N-carbobenzoxy L-ornithine)

Two crystal modifications are found in α-helical poly(δ-N-carbobenzoxy L -ornithine). In films as cast, the two-dimensional unit cell is pseudohexagonal and contains two chains. This form transforms irreversibly into a pseudotetragonal form at about 140°C. A second-order transition associated with the onset of the side-chain motion is observed at about 30°C for the bulk sample (by dilatometry) and for the crystalline phase (by x-ray diffraction). The dielectric behavior of the side-chain dispersion suggests that the side chains interact with one another. The temperature dependence of the infrared absorbance due to the NH stretching vibration reveals that about half the side chains are associated via hydrogen bonds at room temperature and become dissociated at higher temperature. The enthalpy and the entropy of the hydrogen bond formation is estimated to be ΔH = ?5.0 ± 0.5 kcal mol^?1 and ΔS = ?15 ± 1 e.u. mol^?1.     

C-H bond activation of methane in aqueous solution: a hybrid quantum mechanical/effective fragment potential study

In this study, we investigated the C? H bond activation of methane catalyzed by the complex [PtCl₄]^2?, using the hybrid quantum mechanical/effective fragment potential (EFP) approach. We analyzed the structures, energetic properties, and reaction mechanism involved in the elementary steps that compose the catalytic cycle of the Shilov reaction. Our B3LYP/SBKJC/cc‐pVDZ/EFP results show that the methane activation may proceed through two pathways: (i) electrophilic addition or (ii) direct oxidative addition of the C? H bond of the alkane. The electrophilic addition pathway proceeds in two steps with formation of a σ‐methane complex, with a Gibbs free energy barrier of 24.6 kcal mol^?1, followed by the cleavage of the C? H bond, with an energy barrier of 4.3 kcal mol^?1. The activation Gibbs free energy, calculated for the methane uptake step was 24.6 kcal mol^?1, which is in good agreement with experimental value of 23.1 kcal mol^?1 obtained for a related system. The results shows that the activation of the C? H bond promoted by the [PtCl₄]^2? catalyst in aqueous solution occurs through a direct oxidative addition of the C? H bond, in a single step, with an activation free energy of 25.2 kcal mol^?1, as the electrophilic addition pathway leads to the formation of a σ‐methane intermediate that rapidly undergoes decomposition. The inclusion of long‐range solvent effects with polarizable continuum model does not change the activation energies computed at the B3LYP/SBKJC/cc‐pVDZ/EFP level of theory significantly, indicating that the large EFP water cluster used, obtained from Monte Carlo simulations and analysis of the center‐of‐mass radial pair distribution function, captures the most important solvent effects. © 2011 Wiley Periodicals, Inc. J Comput Chem, 2011     

Relaxation behavior of acrylate and methacrylate polymers containing dioxacyclopentane rings in the side chains

The synthesis of poly[(2,2‐dimethyl‐1,3‐dioxolan‐4‐yl) methyl acrylate)] (PACGA) and poly[(2,2‐dimethyl‐1,3‐dioxolan‐4‐yl) methyl methacrylate] (PMCGA) is reported. Both polymers present dielectric and mechanical β subglass absorptions at −128 and −115 °C, respectively, at 1 Hz, followed by ostensible glass–rubber or α relaxations centered in the vicinity of 0 and 67 °C, respectively, at the same frequency. The values of the activation energy of both the mechanical and dielectric β absorptions lie in the vicinity of 10 kcal mol⁻¹. The critical interpretation of the relaxation behavior of PMCGA suggests that dipolar intramolecular correlations play a dominant role in the response of the polymer to an electric field. The subglass relaxations of PACGA and PMCGA are further compared with the relaxation behavior of poly(1,3‐dioxane acrylate), poly(1,3‐dioxane methacrylate), and other polymers in the glassy state. The strong conductive processes observed in PMCGA at low frequencies and high temperatures were studied under the assumption that that these processes arise from Maxwell–Wagner–Sillars effects occurring in the bulk combined with Nernst–Planckian electrodynamic effects caused by interfacial polarization in the films. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 286–299, 2001     

Quantumchemical investigation of borabenzene adduct with pyridine

Atomic charges and structural parameters of borabenzene, pyridine and their adduct in free state, in liquid argon and in tetrahydrofuran are calculated by the quantum-chemical method B3LYP/6-311G(3d5f7,p) &; PCM. Mutual polarization of the adduct and medium results in small increase in boron-nitrogen interatomic distance and dihedral angle between the aromatic heterocycles. Calculated dipole moment of the adduct (7.17 D) is by 4.55 D over than the sum of dipole moments of the free components. Internal rotation barriers are not high: 1 kcal mol^?1 (0° and 180°) and 4 kcal mol^?1 (90°). The borabenzene-pyridine bonding energy (46 kcal mol^?1) is higher than that with dinitrogen (19 kcal mol^?1) and xenon atom (6 kcal mol^?1). The B-N bond length in the little stable adduct with dinitrogen is by 0.08 Å shorter than in the stable adduct with pyridine. The Lewis acid properties inherent in borabenzene are transferred on the π-electron system of pyridine fragment in the adduct. The electron transfer wavelength from borabenzene to pyridine fragment in argon matrix is by 109 nm higher than in tetrahydrofuran, as calculated by CIS CNDO/S method.     

Non-isothermal kinetics of CoOOH decomposition

The non-isothermal 'kinetics of the decomposition of CoOOH powder has been studied derivatographically in a temperature range of 20–450 °C in air. The reaction proceeds in two stages: up to about 280°C with an activation energy E₁ = 38–50 kcal mol^?1 and above that temperature with E₂ = 20–25 kcal mol^?1, depending on the kinetic equations which are employed. The results have been critically discussed on the basis of certain current concepts.     

Influence of chemical exchange on the temperature dependence of Eu(fod)3-induced shifts

Temperature dependences of the paramagnetic shifts induced by Eu(fod)₃ in ¹H NMR spectra of ethylene oxide in carbon disulphide solution are obtained in the temperature range from +40 to ? 100°C at 100 MHz and from +30 to ?60°C at 60 MHz. The influence of chemical exchange leads to a decrease of the observed paramagnetic shifts with decreasing temperature. It is shown that a modified Swift and Connick equation can be used to describe the observed dependences. Upper limits of the mean lifetimes of the Eu(fod)₃-ethylene oxide adduct are τ_p < 1·7 × 10^?8 s at 14 °C and τ_p < 1 × 10^?8 s at 20 °C, respectively. The corresponding activation energy is equal to V_a = 13·7 kcal/mol.     

Effect of lignin content on thermal degradation of wood pulp

A series of pulps containing between 3.6 and 23% of lignin was prepared by a careful delignification of a high-yield bisulfite pulp. The pulps were subjected to isothermal pyrolysis in a Perkin-Elmer TGS-1 thermobalance. The measurements were carried out at 8 different temperatures from 325 to 360°C under nitrogen atmosphere. The results obtained indicate that the effect of lignin on degradation depends strongly on temperature. Below 330°C, the rate of degradation varied only little with lignin. This variation becomes more important at temperatures above 330°C in that the rate of degradation increases with decreasing lignin content. The apparent activation energy of degradation ranges from 41.4 kcal mol^?1 at 23% of lignin to 67.0 kcal mol^?1 at 3.7% of lignin.     

Thermal analysis studies of oil shale residual carbon

Thermal analysis has been used to determine the impact of heating on the decomposition reaction of two Moroccan oil shales between ambient temperature and 500°C. During pyrolysis of raw oil shale, the residual organic matter (residual carbon) obtained for both shales depends on the heating rate (5 to 40°C min^-1). Three stages characterize the overall process: the concentration of carbonaceous residue decreases with increase of heating rate, become stable around 12°C min^-1 and continue to decrease at higher heating rates. Activation energies were determined using the Coats-Redfern method. Results show a change in the reaction mechanism at around 350°C. Below this temperature, the activation energy was 41.3 kJ mol^-1 for the decomposition of Timahdit, and 40.5 kJ mol^-1 for Tarfaya shale. Above this temperature the respective values are 64.3 and 61.3 kJ mol^-1. The reactivity of Timahdit and Tarfaya oil shale residual carbon prepared at 12°C min^-1 was subject to a dynamic air atmosphere to determine their thermal behaviour. Residual carbon obtained from Tarfaya oil shale is shown to be more reactive than that obtained from Timahdit oil shale. This revised version was published online in July 2006 with corrections to the Cover Date.     

Dynamic proton magnetic resonance studies on complex spin systems. Non-mutual three-spin exchange in N-(trideuteriomethyl)-2-cyanoaziridine

At room temperature and below, the proton NMR spectrum of N-(trideuteriomethyl)-2-cyanoaziridine consists of two superimposed ABC patterns assignable to two N-invertomers; a single time-averaged ABC pattern is observed at 158.9°C. The static parameters extracted from the spectra in the temperature range from –40.3 to 23.2°C and from the high-temperature spectrum permit the calculation of the thermodynamic quantities ΔH⁰ = ?475±20 cal mol^?1 (?1.987 ± 0.084 kJ mol^?1) and ΔS⁰ = 0.43±0.08 cal mol^?1 K^?1 (1.80±0.33 J mol^?1 K^?1) for the cis ? trans equilibrium. Bandshape analysis of the spectra broadened by non-mutual three-spin exchange in the temperature range from 39.4–137.8°C yields the activation parameters ΔH_tc^≠ = 17.52±0.18 kcal mol^?1 (73.30±0.75 kJ mol^?1), ΔS_tc^≠ = ?2.08±0.50 cal mol^?1 K^?1 (?8.70±2.09 J mol^?1 K^?1) and ΔG_tc^≠ (300 K) = 18.14±0.03 kcal mol^?1 (75.90±0.13 kJ mol^?1) for the trans → cis isomerization. An attempt is made to rationalize the observed entropy data in terms of the principles of statistical thermodynamics.     

Slow molecular mobility in the amorphous thermoplastic polysulfone

The thermally stimulated depolarization current (TSDC) technique has been used to study the slow molecular mobility of polysulfone in the glassy state and in the glass transformation region, i.e., in the temperature ranging from ?155 to 183 °C. Since the polysulfone is a rigid polymer without polar side-groups, a broad and low-intensity secondary relaxation was detected in the temperature region from ?120 °C up to the glass transition; the activation energy of the motional modes of this secondary relaxation is in the range between 35 and 100 kJ mol^?1. The glass transition temperature of polysulfone provided by the TSDC technique is T _M = T _g = 176 °C (at 4 °C min^?1). The relaxation time at this temperature is τ(T _g) = 33 s and the fragility index was found to be m = 91. Our results are compared with literature values obtained by dynamic mechanical analysis and by dielectric relaxation spectroscopy. The amorphous polysulfone was also characterized by DSC; a glass transition signal with an onset at T _on = 185.5 ± 0.3 °C (heating rate 10 °C min^?1) was detected, with ΔC _p = 0.21 ± 0.01 J g^?1 °C^?1.     

Measurements of electrical conductivity in solid bromine and iodine

Measurements of the electrical conductivity were performed with bromine and iodine in the liquid and the solid states, both containing low concentrations of the corresponding halide ions. In bromine the specific conductivity increases dramatically upon solidification and in iodine it changes only slightly. In both systems the conductivity in the solid is rather high, with remarkably low temperature coefficients, pointing to an unusual mechanism of conduction (of the Grotthuss type) requiring very little movement of the heavy nuclei while the charge is transferred. In mixtures of bromine with a small amount of nitrobenzene (NB) an equivalent conductivity as high as 12 cm² mol^?1 Ω^?1 was observed at ?25°C. In iodine the specific conductivity reached a value of about 0.01 Ω^?1 cm^?1 at 100°C. The energy of activation for conduction in bromine down to ?40°C was found to be about 23 kJ mol^?1, increasing sharply below this temperature. In iodine, values of about 21–27 kJ mol^?1 were observed over the whole temperature range measured.