Synthesis,thermal characterization,and tensile properties of alipharomatic polyesters derived from 1,3‐propanediol and terephthalic,isophthalic, and 2,6‐naphthalenedicarboxylic acid

In this work, three alipharomatic polyesters—poly(propylene terephthalate) (PPT), poly(propylene isophthalate) (PPI), and poly(propylene naphthalate) (PPN)—were prepared and studied with the aliphatic diol 1,3‐propanediol and the corresponding aromatic diacids. Their synthesis was performed by the two‐stage melt polycondensation method in a glass batch reactor. The thermal characterization of these polyesters was carried out with different thermal techniques such as simultaneous thermogravimetry/differential thermal analysis, thermomechanical analysis (TMA), and dynamic thermomechanical analysis. From the recorded values for the glass‐transition temperature (T_g) and melting temperature with all the aforementioned techniques, it could be said that they were in good agreement. According to the thermogravimetric results, PPT and PPI showed about the same thermal stability, whereas PPN seemed to be somewhere more thermostable. Remarkably, a transition existed immediately after T_g that was realized by the first derivative of TMA, and it was characterized as a midrange transition. For all polyesters, the average coefficient of linear thermal expansion was calculated with TMA. The secondary relaxations T_β and T_γ, recorded with dynamic mechanical thermal analysis, were mainly affected by the kinds of monomers. Concerning the mechanical properties, PPN had the highest tensile strength at break, whereas PPT had the highest elongation at break. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3998–4011, 2005     

Mechanism of high thermal stability of commercial polyesters and polyethers conjugated with bio‐based caffeic acid

In previous report, we discovered that a novel improvement technique to enhance the thermal properties of poly(L ‐lactide)s (PLLAs) by terminal conjugation with 3,4‐diacetoxycinnamic acid (DACA). In this study, we clarified the mechanism of the enhancement of thermal stability by using commercial polyesters and polyethers. The effect of thermal improvement by the terminal conjugation of DACA on poly(DL ‐lactide), poly(ε‐caprolactone), and poly(ethylene glycol) was almost the same as about 100 °C increase. The amount of residual tin catalyst, which enhances the thermal degradation of polyesters, was reduced at undetected level after the terminal conjugation of DACA probably due to the removal of tin during DACA conjugation process. Furthermore, the π‐π stacking interactions of DACA units and the chemical protection of terminal hydroxyl groups, which enhances intramolecular scission, were also important for the high thermal stability. We clarified that the extreme high thermal stability by DACA conjugation was induced by these above mechanisms. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Dielectric relaxations in linear aliphatic polyesters

Molecular motions in a series of linear aliphatic polyesters [poly(ethylene adipate), poly(ethylene sebacate), poly(hexamethylene sebacate), and poly(decamethylene 1,16-hexadecanedicarboxylate)] were studied by dielectric measurements. Two loss maxima were observed for each polymer in the temperature range from ?196 to about 60°C and in the frequency range from 110 to 10⁵ Hz. The loss maxima of these polyesters, lying between ?17 and ?38°C at 110 Hz (β-relaxation), are due to the micro-Brownian motions of amorphous main chains. It was found that these β-relaxations are well described by the WLF equation. The loss maxima in the range from ?88 to ?109°C at 110 Hz (γ-relaxation), are attributed both to local mode motions of main chains in the amorphous region and to motions of the polar groups involved at the chain ends. For the β-relaxation, no simple relation between the methylene sequence length and the loss peak temperature was found. Furthermore, as the methylene sequence length decreased, the effective dipole moment of the polyesters increased gradually. These facts were explained in terms of interchain dipole attraction.     

Poly(ethylene terephthalate) reinforced by N,N′‐diphenyl biphenyl‐3,3′,4,4′‐tetracarboxydiimide moieties

Starting with 3,3′,4,4′‐biphenyltetracarboxylic dianhydride and methyl aminobenzoate, we synthesized a novel rodlike imide‐containing monomer, N,N′‐bis[p‐(methoxy carbonyl) phenyl]‐biphenyl‐3,3′,4,4′‐tetracarboxydiimide (BMBI). The polycondensation of BMBI with dimethyl terephthalate and ethylene glycol yielded a series of copoly(ester imide)s based on the BMBI‐modified poly(ethylene terephthalate) (PET) backbone. Compared with PET, these BMBI‐modified polyesters had higher glass‐transition temperatures and higher stiffness and strength. In particular, the poly(ethylene terephthalate imide) PETI‐5, which contained 5 mol % of the imide moieties, had a glass‐transition temperature of 89.9 °C (11 °C higher than the glass‐transition temperature of PET), a tensile modulus of 869.4 MPa (20.2 % higher than that of PET), and a tensile strength of 80.8 MPa (38.8 % higher than that of PET). Therefore, a significant reinforcing effect was observed in these imide‐modified polyesters, and a new approach to higher property polyesters was suggested. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 852–863, 2002; DOI 10.1002/pola.10169     

Degradable polymer blends. I. Screening of miscible polymers

Blends of biodegradable polymers having properties distinct from the individual polymer components, and that are suitable for use as carriers of pharmaceutically active agents, were prepared from two or more polyanhydrides, polyesters, and mixtures of polyanhydrides and low molecular weight polyesters. The blends have different properties than the original polymers, providing a mean for altering the characteristics of the polymeric matrix without altering the chemical structure of the component polymers. Aliphatic, aromatic, and copolymers of polyanhydrides were miscible in each other and formed less crystalline compositions with a single melting point which was lower than the melting point of the starting polymers. The polyesters: poly(lactide-glycolide), poly(caprolactone), and poly(hydroxybutyric acid) presented some miscibility in each other. However, the polyanhydrides were immiscible with the polyesters resulting in a complete phase separation both in solution or in melt mixing. Only low molecular weight polyesters (in the range of 2000) of lactide and glycolide, mandelic acid, propylenefumarate, and caprolactone presented some miscibility with polyanhydrides. Similarly, poly(orthoester) and hydroxybutyric acid polymers formed a uniform mixture with the anhydride polymers which had the two melting points of the original polymers. Drug release from polymer blends composed of poly(hydroxybutyric acid) or low molecular weight poly(lactic acid) with poly(sebacic anhydride) (PSA) showed a constant release of drug for periods from 2 weeks to several months as a function of the PSA content in the blend. Increasing the content of PSA, a fast degrading polymer, increases the release rate from the blend. © 1993 John Wiley & Sons, Inc.     

Isothermal melt-crystallization and melting behavior for three linear aromatic polyesters

Isothermal crystallization and subsequent melting behavior for three different types of linear aromatic polyester, namely poly(ethylene terephthalate) (PET), poly(trimethylene terephthalate) (PTT), and poly(butylene terephthalate) (PBT), were investigated (with an emphasis on PTT in comparison with PET and PBT). These polyesters were different in the number of methylene groups (i.e. 2, 3, and 4 for PET, PTT, and PBT, respectively). Isothermal crystallization studies were carried out in a differential scanning calorimeter (DSC) over the crystallization temperature range of 182-208 °C. The wide-angle X-ray diffraction (WAXD) technique was used to obtain information about crystal modification and apparent degree of crystallinity. The kinetics of the crystallization process was assessed by a direct fitting of the experimental data to the Avrami, Tobin, and Malkin macrokinetic models. It was found that the crystallization rates of these polyesters were in the following order: PBT>PTT>PET, and the melting of these polyesters exhibited multiple-melting phenomenon. Lastly, the equilibrium melting temperature for these polyesters was estimated based on the linear and non-linear Hoffman-Weeks (LHW and NLHW) extrapolative methods.     

Internal motion in some aromatic polyesters and linear aromatic chains

Low-temperature internal motions of the following polyesters have been investigated by broad line nuclear magnetic resonance: poly(methylene terephthalates) (2–6 methylene groups), poly[1,4-(dimethylene)cyclohexylene terephthalate], poly(diethyleneglycol terephthalate), poly(1,2-propylene terephthalate), poly(1,4-phenylene terephthalate), poly(2,2,3,3,4,4-hexafluoropentamethylene terephthalate), poly[1,4-phenylenebis(dimethyl) siloxane], and poly(2,6-dimethylphenylene oxide). No complex line structure was found for any of the samples. Molecular motions in the polyesters appear to be restricted by polar forces arising from the ester groups. Above—196°C. the line width decreases smoothly with increasing temperatures for all polymers except poly[1,4-(dimethylene)cyclohexylene terephthalate] and poly[1,4-phenylenebis(dimethyl)siloxane]. These two show a definite transition in line width at ?20°C. and +12°C., respectively, caused by the onset of considerable internal motion. At ?196°C. the lattices are rigid except for polymers containing methyl groups: poly(1,2-propylene terephthalate), poly[1,4-phenylenebis(dimethyl) siloxane], and poly(2,6-dimethylphenylene oxide). Internal motion that can be ascribed to be a reorientation of the methyl groups is present at ?196°C. for these three polymers, as is demonstrated by comparison of experimental second moments and those calculated on the basis of various models.     

Les melanges polyester/poly(bromure de vinyle)

DSC measurements indicate that poly(vinyl bromide) (PVB) is miscible with several polyesters [poly(caprolactone), poly(valerolactone), poly(butylene adipate) and poly(hexamethylene sebacate)] but immiscible with others [poly(α-methyl-α-n-propyl-β-propiolactone), poly(α-methyl-α-ethyl-β-propiolactone) and poly(ethylene adipate (PEA)]. However, it is known that poly(vinylchloride) (PVC) is miscible with all these polyesters but PEA. The more limited degree of miscibility of PVB with polyesters, as compared with the case of PVC, is surprising in view of the similar properties of the bromine and chlorine atoms.     

Thermal degradation of environmentally degradable poly(hydroxyalkanoic acid)s

Aliphatic polyesters have attracted industrial attention as environmentally degradable thermoplastics to be used for a wide range of applications. Besides intensive studies on the biodegradability of aliphatic polyesters, understanding of the thermal stability has importance for processing, application, and recycling. The details of thermal degradation processes of five types of aliphatic polyesters; namely, poly(L-lactide), poly(3-hydroxybutyric acid), poly(4-hydroxybutyric acid), poly(delta-valerolactone), and poly(epsilon-caprolactone), were investigated by means of several thermoanalytical techniques under both isothermal and non-isothermal conditions. In this feature article, the thermal degradation behaviors of aliphatic polyesters with different numbers of carbon atoms in the main chain of the monomeric unit are reviewed. In addition, the effects of chain-end structure and residual metal compounds on the thermal degradation processes of aliphatic polyesters consisting of hydroxyalkanoic acid monomeric units are presented. Schemes of thermal degradation reaction of poly(hydroxyalkanoic acid)s.     

Thermal and mechanical behaviour of flexible poly(vinyl chloride) mixed with some saturated polyesters

Four saturated polyesters poly(hexamethylene adipate), poly(ethylene adipate), poly(hexamethylene terephthalate) and poly(ethylene terephthalate) were prepared. The resulting materials were characterized by IR and ¹H NMR, end group analysis and gel permeation chromatography. The effect of blending these polyesters (5 and 10%) with poly(vinyl chloride) (PVC) in the melt was investigated in terms of changes in the thermal behaviour of PVC by studying the weight loss after 50 min at 180 °C, colour changes of the blend before and after aging for one week at 90 °C, the variation in glass transition temperature and the initial decomposition temperature. The results gave proof for the stabilizing role played by the investigated polyesters against the thermal degradation of PVC. The best results are obtained when PVC is mixed with 5% aliphatic polyesters rather than with aromatic ones. This is well illustrated not only from the increase in the initial decomposition temperature (IDT), but also from the decrease of % weight loss and from the lower extent of discolouration of PVC, which is a demand for the application of the polymer. It was also found that blending PVC with 5% of the four investigated polyesters before and after aging for one week at 90 °C gave better mechanical properties even than that of the unaged PVC blank.     

Synthesis and hydrolytic degradation of poly (glycerol succinate) based polyesters

The limited availability of petroleum resources motivates the research towards value-added products production from bio-resources. This study reports the synthesis of glycerol and succinic acid-based polyesters and their detailed characterization. The modification of poly (glycerol succinate) was done by using other diacids like glutaric acid, adipic acid, azelaic acid, sebacic acid, and dodecanedioic acid. The sysnthesized polyesters were characterized using various techniques such as thermogravimetric analysis (TGA), Fourier-transform infrared spectroscopy (FTIR), Nuclear magnetic resonance (NMR), differential scanning calorimetry (DSC), and scanning electron microscopy (SEM). The addition of different dicarboxylic acids to poly (glycerol succinate) based co-polyesters increased the thermal stability of poly (Glycerol succinate). Glass transition temperatures were obtained in the range of ?17.2 to ?22.5 °C and it increased with chain length. The progress of reaction was monitored by determining acid number, ester number, and degree of esterification. The hydrolytic degradation of polyesters was carried out in acidic and basic medium. The polyesters was found to degrade under basic conditions whereas no weight loss of poly (glycerol succinate) was found under acidic conditions. Particularly, about 40% of poly (glycerol succinate) was degraded within 24 h under basic conditions (pH = 12). The analysis of morphology of polyesters during degradation showed that the increase in hydrolysis time increased the heterogeneity in polyester matrix.     

Complete miscibility of ternary aryl polyesters demonstrating a new criterion and horizon for miscibility characterization

A ternary miscible blend system comprising only crystallizable aryl polyesters [poly(ethylene terephthalate), poly(trimethylene terephthalate), and poly(butylene terephthalate)] was characterized with the criteria of thermal analyses, microscopy, and X‐ray characterizations. The reported ternary miscibility (in the quenched amorphous state of blends of the three aryl polyesters) was truly physical and under the condition of no chemical transesterifications; this justified that transesterification was not a necessary condition for miscibility in polyester blends in this case. This study further proposed and tested a novel concept of a new criterion for miscibility characterization for polymer blends of only crystallizable polymers. A single composition‐dependent cold‐crystallization‐temperature (T_cc) peak in blends of only semicrystalline polymers was taken as an indication of an intimate mixing state of miscibility. The theoretical background for establishing the single composition‐dependent T_cc peak as a valid miscibility criterion for crystallizable polymer blends was examined. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2394–2404, 2003     

Synthesis, characterization and thermal degradation mechanism of three poly(alkylene adipate)s: Comparative study

Three high molecular weight aliphatic polyesters derived from adipic acid and the appropriate diol - poly(ethylene adipate) (PEAd), poly(propylene adipate) (PPAd) and poly(butylene adipate) (PBAd) - were prepared by two-stage melt polycondensation method (esterification and polycondensation) in a glass batch reactor. Intrinsic viscosities, GPC, DSC, NMR and carboxylic end-group measurements were used for their characterization. Mechanical properties of the prepared polyesters showed that PPAd has similar tensile strength to low-density polyethylene while PEAd and PBAd are much higher. From TGA analysis it was found that PEAd and PPAd have lower thermal stability than poly(butylene adipate) (PBAd). The decomposition kinetic parameters of all polyesters were calculated while the activation energies were estimated using the Ozawa, Flynn and Wall (OFW) and Friedman methods. Thermal degradation of PEAd was found to be satisfactorily described by one mechanism, with activation energy 153 kJ/mol, while that of PPAd and PBAd by two mechanisms having different activation energies: the first corresponding to a small mass loss with activation energies 121 and 185 kJ/mol for PPAd and PBAd, respectively, while the second is attributed to the main decomposition mechanism, where substantial mass loss takes place, with activation energies 157 and 217 kJ/mol, respectively.     

Structural Effects on the Biodegradation of Aliphatic Polyesters

In advance of a discussion on structural effects on biodegradation, aliphatic polyesters as biodegradable structural materials were classified into four types regarding chemical structure, that is poly(ω-hydroxy acid), poly(β-hydroxyalkanoate), poly(ω-hydroxyalkanoate) and poly(alkylene dicarboxylate), and reviewed on synthesis route, thermal and physical properties, and biodegradability. The biodegradation mechanism of these aliphatic polyesters were discussed on the major mode of hydrolysis reaction in regard whether it was enzyme-catalyzed or not, and the substrate specificities of enzymes, such as lipases or PHA depolymerases, were discussed on the hydrolysis of the aliphatic polyesters in respect of primary structure. Moreover, the biodegradation behaviors were exceedingly influenced by solid-state morphology in addition to primary structure. The rate of enzymatic degradation of polycaprolactone fibers drawn with various draw ratios was dependent on draw ratios, suggesting that crystallinity and orientation of them affected biodegradability by lipase. In the study of enzymatic degradation of films made from butylene succinate – ethylene succinate copolymer, the dependence of degradation rate on polymeric compositions was ascribed to the degree of crystallinity rather than the primary structure. These studies revealed that the degree of crystallinity was the major rate-determining factor of biodegradation of solid polymers. © 1997 John Wiley & Sons, Ltd.     

Photolysis of polyesters: Poly(propylene-1,2-maleate) and poly(propylene-1,2-ortho-phthalate)

A spectroscopic study of the photo-oxidation of poly(propylene-1,2-maleate), poly(propylene-1,2-o-phthalate) and poly(propylene-1,2-maleate-o-phthalate) under 280–480 nm radiation was investigated in detail. Results obtained indicate that, during photolysis of these polyesters, the primary photoreactions involve excitation of conjugated structures: carbonyl groups (in ester groups)—double bonds or carbonyl groups-phenylene rings. The secondary reactions occur by complicated mechanisms resulting in oxidation, scission, radical termination and cross-linking of structures present in the photolysed polyesters. Light of wavelength 280–480 nm causes deterioration in the polyesters in the early stages of irradiation. Singlet oxygen does not react with these polyesters even during long periods of exposure. Photo-oxidation mechanism occurs by free radical mechanism.     

Permeability of N2, Ar,He, O2, and CO2 through as‐extruded amorphous and biaxially oriented polyester films: Dependence on chain mobility

For as‐extruded amorphous and biaxially orientated polyester films based on poly(ethylene terephthalate), poly(ethylene naphthalate), and copolymers containing poly(ethylene terephthalate) and poly(ethylene naphthalate) moieties, permeability, diffusion, and solubility coefficients are interpreted in terms of chain mobility. The influence of polymer morphology is determined by comparison of the data for as‐extruded amorphous sheets and materials produced with different biaxial draw ratios. The crystallinities of the samples were assessed using differential scanning calorimetry and density measurements. Changes in mobility at a molecular level were investigated using dielectric spectroscopy and dynamic mechanical thermal analysis. The study, in conjunction with our earlier work, leads to the conclusion that the key to understanding differences in gas transport is the difference in local chain motions rather than in free volume. This was illustrated by the permeability results for He, Ar, N₂, and O₂ in the range of polyesters. However, the permeability of CO₂ was found to require alternative explanations because of polymer–penetrant interactions. For biaxially oriented samples, the differences in diffusivity are not only due to differences in local chain motions, but also additional constraints resulting from the increased crystallinity and chain rigidity—which also act to hinder segmental mobility. The effectiveness of the reduction in permeability in the biaxially oriented films is consequently determined by the ability of the polymer chains to effectively align and form crystalline structures. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2916–2929, 2004     

Spontaneous thinning/thickening deformation observed for plastic blend films and some factors affecting film deformation

The fully amorphous films of highly syndiotactic poly[(R,S)‐3‐hydroxybutyrate] (s‐PHB)/atactic poly(4‐vinylphenol) (PVPh) blends show reversible thinning/thickening phenomena at 37 °C in aqueous medium. On the other hand, isotactic poly[(R)‐3‐hydroxybutyrate] (i‐PHB)/PVPh blend film, in which i‐PHB blend component was partially crystalline, did not show any thinning/thickening phenomena under the same conditions. To elucidate the factors influencing these phenomena, the structure and molecular interaction in these blends were characterized by Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry, and wide‐angle X‐ray diffraction. The FTIR spectra indicated that the ester carbonyl of PHB and the phenolic hydroxyl of PVPh formed hydrogen bonds in both the thinned and thickened s‐PHB/PVPh blend films. The blend composition, intermolecular hydrogen‐bonding interaction, crystallization behavior, miscibility, and the glass‐transition temperature of the blends affected the thinning/thickening phenomena. Some other polyesters such as poly(?‐caprolactone), poly (L‐lactic acid), atactic poly(D,L‐lactic acid), and poly(ethylene terephthalate) had no ability to exhibit thinning/thickening phenomena in water at 37 °C when they were blended with PVPh. This result implies that s‐PHB/PVPh is the rare example with the ability to show reversible thinning/thickening phenomena. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2736–2743, 2002     

Synthesis and comparative study of biodegradable poly(alkylene sebacate)s

Novel biodegradable polyesters, such as poly(ethylene sebacate) (PESeb), poly(propylene sebacate) (PPSeb), and poly(butylene sebacate) (PBSeb), were synthesized and studied with respect to melting behavior, crystallization kinetics, and enzymatic hydrolysis. PESeb and PPSeb showed multiple melting behavior. Wide angle X‐ray diffractometry measurements at various temperatures, standard, step‐scan, and high‐rate differential scanning calorimetry methods were applied to elucidate the appearance of multiple endotherms in heating scans, which was interpreted in the context of partial melting‐recrystallization and final melting. PBSeb did not show any multiple melting behavior but only a weak tendency for recrystallization on heating. The melting temperatures of PESeb, PPSeb, and PBSeb were measured equal to 78, 57, and 71 °C, respectively. The equilibrium melting points were estimated to be T_m° = 90.2, 69.9, and 77.4 °C for PESeb, PPSeb, and PBSeb, while the corresponding enthalpy of fusion values were found to be ΔH_f = 170 ± 10, 140 ± 10, and 155 ± 10 J/g, respectively. The polyesters showed fast crystallization rates under both isothermal and nonisothermal conditions. Crystallization kinetics was thoroughly investigated using macrokinetic models and isoconversional analysis. Enzymatic hydrolysis rate in the presence of lipases Rhizopus delemar and Pseudomonas cepacia was found to be fast for PPSeb, whereas PESeb and PBSeb showed slow rates and comparable with those of PCL. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 672–686, 2010     

Synthesis,characterization, metal sorption,and biological activities of organosoluble and thermally stable azoxanthone‐based polyester

The aim of this work was to develop functionalized polyxanthones, poly(azoxanthone‐ester)s (PAXEs), with biological activities and heavy metal sorption abilities. For this purpose, at first, new xanthone‐based diol moiety was synthesized and then used for polymerization with commercial dicarboxylic acids via polycondensation reaction by Vilsmeier adducts. The monomer and all polymers were characterized by Fourier transform infrared (FTIR) and Nuclear magnetic resonance (NMR) spectroscopies, and the physical properties of these PAXEs including solution viscosity, solubility properties, thermal stability, and thermal behavior were studied. The prepared polyesters showed excellent thermal stability and good solubility in polar aprotic solvents. In addition, evaluation of antioxidant activity of the PAXEs by 2,2‐diphenyl‐1‐picrylhydrazyl assay revealed that synthesized polymers have higher antioxidant activity than xanthone nucleus. Also, evaluation of the antibacterial activities of the diol monomer and polymer showed good antibacterial activity against some bacterial strains (Staphylococcus aureus, Bacillus subtilis, Escherichia coli, and Pseudomonas aeruginosa). The results showed that these PAXEs can be used in pharmaceutical and food industry (food packaging). Furthermore, these functionalized polyesters were utilized for extraction of environmentally harmful metal cations such as Cr (VI), Co (II), Ni (II), Cu (II), Pb (II), and Cd (II) from aqueous solutions. Copyright © 2015 John Wiley & Sons, Ltd.     

Some Comments on a Recent Article Dealing with Three Aliphatic-Aromatic Polyesters and Their Spectral Identification

This work discusses the results appearing in Wu et al.’s (2014) article dealing with three aliphatic-aromatic polyesters based on terephthalic acid and their spectral identification. Using an instrument equipped with a switch that allows ions with masses below 5 kDa to be discarded (ion deflector), the authors report the MALDI spectrum of a commercial poly(ethylene terephthalate) with signals up to 80 kDa. I plot the spectral intensities and fit them with a Gaussian curve. The result is carefully examined. Thereafter, attention is moved to the MALDI spectra obtained when the ion deflector is turned off. A computation that gives the number-average and the weight-average molar mass (Mn and Mw) was performed, but the result was Mn = 1362 g/mol and Mw = 1416 g/mol. These values are much too low and they cannot be used. In order to explain this failure, I modified a model developed for poly(pentylene adipate). This hypothesis is discarded and the correct explanation is found. I also discuss other types of instrumentation, for instance, Py-GC/MS combined with library-search and also NMR spectroscopy, with specific reference to the chemical shifts of the -CH2- protons in aliphatic-aromatic polyesters.