Facile synthesis of highly conductive polyaniline/graphite nanocomposites

A facile process for the synthesis of exfoliated graphite and polyaniline/graphite (PANI/graphite) nanocomposite was developed. Graphite nanosheets were prepared via the microwave irradiation and sonication from synthesized expandable graphite. The nanocomposites were fabricated via in situ polymerization of aniline monomer in the presence of graphite nanosheets. The nanoscale dispersion of graphite sheets was evidenced by the SEM and TEM examinations. According to the electrical conductivity test, the conductivity of the final PANI/graphite nanocomposites were dramatically increased compared with pristine PANI. From the thermogravimetric analysis, the introduction of graphite exhibits a beneficial effect on the thermal stability of PANI.     

Preparation of highly conductive, self-assembled gold/polyaniline nanocables and polyaniline nanotubes

One-dimensional gold/polyaniline (Au/PANI-CSA) coaxial nanocables with an average diameter of 50-60 nm and lengths of more than 1 mum were successfully synthesized by reacting aniline monomer with chlorauric acid (HAuCl(4)) through a self-assembly process in the presence of D-camphor-10-sulfonic acid (CSA), which acts as both a dopant and surfactant. It was found that the formation probability and the size of the Au/PANI-CSA nanocables depends on the molar ratio of aniline to HAuCl(4) and the concentration of CSA, respectively. A synergistic growth mechanism was proposed to interpret the formation of the Au/PANI-CSA nanocables. The directly measured conductivity of a single gold/polyaniline nanocable was found to be high (approximately 77.2 S cm(-1)). Hollow PANI-CSA nanotubes, with an average diameter of 50-60 nm, were also obtained successfully by dissolving the Au nanowire core of the Au/PANI-CSA nanocables.     

Antistatic applications of conducting polyaniline

A method is described to impart flexibility and mechanical strength to conducting polyaniline by polymerizing aniline on fabrics and on cellulose papers. The study indicates that these conducting fabrics offer 16–18 dB of shielding effectiveness for the control of electromagnetic interference (EMI) up to a frequency of 10³ MHz.     

Film thickness studies for the chemically synthesized conducting polyaniline

The chemical oxidation of aniline with ammonium persulphate (APS) in aqueous acidic medium to form polyaniline (PANI) films has been studied using the quartz crystal microbalance (QCM) technique. PANI films can also grow onto glass supports immersed in the reaction mixture during the polymerization. The optical absorption for these films was measured. Multilayer deposition of polymer films onto the gold electrode of QCM and onto the glass supports from consecutive repetitive treatments by the reaction mixture containing aniline and APS, were studied. The induction period, the yield and the growth rate of the polymer films during the multilayer deposition were discussed. A relation between the thickness of the films determined, from QCM technique and the optical absorption of the films was established. The electrical conductivity of the PANI films was also measured.     

Facile preparation of highly conductive,flexible, and strong carbon nanotube/polyaniline composite films

In general, the high electrical conductivity (EC) comes into conflict with the good flexibility and high strength of carbon nanotube (CNT)/polyaniline (PANI) composites. In other words, a high CNT content will bring about a high EC but lead to a low flexibility and strength due to the CNT‐constrained matrix deformation and CNT aggregation. In this work, a highly conductive, flexible and strong CNT/PANI composite film prepared via a facile solvent‐evaporation method is readily obtained by a cold stretching. The cold stretching is conducted at room temperature for the CNT/PANI film. It is observed that the cold stretching process leads to an unexpectedly enhanced EC. The as‐obtained EC of 231 S/cm is much higher than that (2 – 50 S/cm) of the previously reported CNT/PANI composite films. Meanwhile, the strength is obviously improved over that of the pure PANI film and the good flexibility is maintained to a high degree by the introduction of a proper CNT content. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1575–1585     

导电聚苯胺/钙基膨润土复合材料的制备

采用插层聚合法制备了导电聚苯胺/钙基膨润土、聚苯胺/有机化膨润土复合材料.以电导率为考核指标,通过正交设计优化了苯胺的加入量、反应温度和反应时间等参数.结果表明,苯胺的加入量影响较显著,反应温度对聚苯胺/有机化膨润土复合材料影响较聚苯胺/钙基膨润土体系明显,反应时间的延长,有利于聚苯胺/有机化膨润土复合材料电导率的提高.聚苯胺/钙基膨润土复合材料制备的最佳工艺条件为:苯胺加入量为70%,反应温度为0℃,反应时间为6 h;聚苯胺/有机化膨润土复合材料制备的最佳工艺条件为:苯胺加入量为70%,反应温度为室温,反应时间为8 h.利用红外光谱(FT-IR)、X射线衍射(XRD)和四探针技术表征了材料的组成、结构和性能.结果表明:膨润土经有机化后,晶面间距增大较多;苯胺单体与钙基膨润土插层聚合后,膨润土晶面间距增大不多;苯胺单体与有机化膨润土复合后,破坏了膨润土的晶格结构,形成了混杂复合体系,电导率达10-3S.cm-1.     

Computer-aided selection of a polymer matrix for polyaniline conductive blends

The selection of a polymer matrix for a conductive blend with polyaniline and para-toluene sulfonic acid (PANI-pTSA) was performed using molecular simulation techniques, both a fast quantitative structure–properties relationship method as a first screening phase followed by atomistic simulation. Using the atomistic simulation method, the solubility parameters and the heat of mixing of each blend were calculated to enable the determination of compatible matrices in blends with PANI-pTSA, which was validated by experimental scanning electron microscopy fractographs. Based on such calculations, polycaprolactone (PCL)/PANI-pTSA phase diagrams were estimated, showing slight miscibility of polydispersed PANI in PCL, particularly the short chains fraction, at the elevated melt processing temperature. It was suggested that this partial miscibility at the elevated temperature might lead to a conductive network morphology of PANI in PCL at room temperature, because of phase separation and precipitation of soluble PANI molecules, upon cooling and solidification of the melt. © 1998 John Wiley & Sons, Ltd.     

Graphene oxide‐induced polymerization and crystallization to produce highly conductive polyaniline/graphene oxide composite

Graphene oxide (GO)–polyaniline (PANI) composite is synthesized by in situ polymerization of aniline in the presence of GO as oxidant, resulting in highly crystalline and conductive composite. Fourier transform infrared spectrum confirms aniline polymerization in the presence of GO without using conventional oxidants. Scanning electron microscopic images show the formation of PANI nanofibers attached to GO sheets. X‐ray diffraction (XRD) patterns indicate the presence of highly crystalline PANI. The sharp peaks in XRD pattern suggest GO sheets not only play an important role in the polymerization of aniline but also in inducing highly crystalline phase of PANI in the final composite. Electrical conductivity of doped GO–PANI composite is 582.73 S m^?1, compared with 20.3 S m^?1 for GO–PANI obtained by ammonium persulfate assisted polymerization. The higher conductivity appears to be the result of higher crystallinity and/or chemical grafting of PANI to GO, which creates common conjugated paths between GO and PANI. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1545–1554     

Facile synthesis of processable conductive water solubilized polyaniline

Conductive polyaniline, polyemeraldine green, was synthesized in a water soluble form by an in situ method, using surfactants with strong acid functionalities as protonating agents. The clear green solution of conducting polyaniline, polyemeraldine green, can be diluted to any extent and stored. Thin and thick films can be easily processed from this solution by spin coating and solvent casting methods.     

导电聚苯胺的热分析及粘弹性能研究

本文用热分忻的方法和粘弹谱仪对聚苯胺（ＰＡＮ）的热性能和粘弹性进行了研究．结果表明ＰＡＮ的耐热性较好，本征态（非掺杂）ＰＡＮ的玻璃化转变温度为 １３４℃，转变活化能为 ２７３ＫＪ／ｍｏｌ．     

About the capacitive currents in conducting polymers: the case of polyaniline

Journal of Solid State Electrochemistry - In the present work, we review the occurrence of capacitive currents in conducting polymer and, particularly, in the electrochemical response of...     

Synthesis of self-doped conducting polyaniline bearing phosphonic acid

As a self-doped conducting polyaniline bearing phosphonic acid, poly(2-methoxyaniline-5-phosphonic acid) (PMAP) was synthesized via oxidative polymerization of 2-methoxyaniline-5-phosphonic acid. The pyridinium salt of thus-obtained PMAP was water-soluble and its film exhibited conductivity.     

Temperature- and humidity-related degradation of conducting polyaniline films

The time dependence of dc conductivity of conducting polyaniline films was measured in relation to temperature and relative humidity of the environment. Optical and structural properties of the samples were checked using Fourier transform infrared (FTIR) spectroscopy.     

Ionic liquid improves the laccase-catalyzed synthesis of water-soluble conducting polyaniline

The laccase-catalyzed polymerization of aniline in sodium dodecyl benzene sulfonate (SDBS) micellar solution was studied in the absence and presence of an ionic liquid tetramethylammonium trifluoromethanesulfonate ([TMA]TfO). It was found that [TMA]TfO was able to lessen the negative effect of SDBS on the laccase activity, especially at high levels, and prevent the association of anilinium cation and SDBS anion. It was also found that low level of [TMA]TfO is beneficial to the synthesis of conducting polyaniline (PANI) probably due to the extension of the lifetime of aniline cation radicals by [TMA]TfO. In the presence of [TMA]TfO, all the polymerization systems were visually clear, and a maximum yield of water-soluble conducting PANI could be obtained at low level of [TMA]TfO and near the critical micelle concentration of SDBS.     

Enhanced electrorheology of conducting polyaniline confined in MCM-41 channels

A composite material of a silica-based mesoporous molecular sieve, MCM-41, with conducting polyaniline (PANI) inside the uniformly aligned one-dimensional channels (PANI/MCM-41) was prepared and its nanocomposite formation was confirmed through an electrical conductivity measurement. This nanocomposite particle was adopted for a dispersed phase in electrorheological (ER) fluids, and the ER property was measured using a Couette-type rotational rheometer equipped with a high voltage generator. Suspension of PANI/MCM-41 showed ER properties more enhanced than those of MCM-41 or PANI alone as a result of the anisotropic polarization of the PANI/MCM-41 nanocomposite.     

Preparation and characterization of polyaniline/MMT conductive composites

Polyaniline/montmorillonite (PAn/MMT) composite material has been prepared through chemical‐oxidative polymerization by using NH₄S₂O₈ as the oxidant, and it was found that both the composites have inorganic and organic material characteristics and many outstanding performance through the copolymerization coupling of MMT and polyaniline. Infrared spectroscopy (FT‐IR), thermogravimetric analysis (TGA), X‐ray diffraction (XRD), and transmission electron microscopy (TEM) are used to characterize the composition and structures of composite materials, as well as test the conductivity of composite materials through a four‐probe technique. The preparation conditions of PAn/MMT conducting composites are optimized. The optimal conditions have been identified for the reaction time, amount of oxidizer, concentration of HCl, and the amount of MMT. Besides, the results show that when the reaction lasts for 8 hr in the ice bath, the amount of MMT is 0.4 g/5 ml An, the mole ratio of oxidant to aniline is 1, and the concentration of hydrochloric acid is 2 M, the composite had the largest conductivity up to 11.5 S/cm. In addition, we also did an elemental analysis of the composite mechanism of PAn/MMT composites. Copyright © 2008 John Wiley & Sons, Ltd.     

Self-assembled networks of conducting polyaniline in bulk polymers: A new class of conducting polymer blends

This review of the current status of conducting polymers will focus on recent progress which demonstrates that the initial promise of the late 1970's has become reality. Conducting polymers are now available as materials with truly unique properties: They combine the important electronic and optical properties of semiconductors and metals with the attractive mechanical properties and processing advantages of polymers. Conducting polymer blends based upon polyaniline (PANI) are a new class of materials in which the threshold for the onset of electrical conductivity (σ) can be reduced to volume fractions below 1%, well below that required for classical percolation (16% by volume for globular conducting objects dispersed in an insulating matrix in three dimensions). The origin of this remarkably low threshold for the onset of electrical conductivity is the self-assembled network morphology of the PANI polyblends which forms during the course of liquid-liquid separation. Since the average density of the conducting network near threshold is small, the conductivity increases smoothly and continuously over many orders of magnitude as the concentration of conducting polymer increases above threshold. The low percolation threshold and the continuous increase of σ(f) above threshold are particularly important; as a result of this combination, conducting polyblends can be reproducibly fabricated with controlled levels of electrical conductivity while retaining the desired mechanical properties of the matrix polymer.^1-3)