Structure and molecular conformation of tussah silk fibroin films: Effect of methanol

Structural changes of tussah (Antheraea pernyi) silk fibroin films treated with different water-methanol solutions at 20°C were studied as a function of methanol concentration and immersion time. X-ray diffraction measurements showed that the α-helix structure, typical of untreated tussah films, did not change for short immersion times (2 min), regardless of methanol concentration. However, crystallization to β-sheet structure was observed following immersion of tussah films for 30 min in methanol solutions ranging from 20 to 60% (v/v). IR spectra of tussah films untreated and methanol treated for 2 min exhibited strong absorption bands at 1265, 892, and 622 cm^?1, typical of the α-helix conformation. The intensity of the bands assigned to the β-sheet conformation (1245, 965, and 698 cm^?1) increased for the sample treated with 40% methanol for 30 min. Raman spectra of tussah films with α-helix molecular conformation exhibited strong bands at 1657 (amide I), 1263 (amide III), 1106, 908, 530, and 376 cm^?1. Following α → β conformational transition, amide I and III bands shifted to 1668, and to 1241, 1230 cm^?1, respectively. The band at 1106 cm^?1 disappeared and new bands appeared at 1095 and 1073 cm^?1, whereas the intensity of the bands at 530 and 376 cm^?1 decreased significantly. ©1995 John Wiley & Sons, Inc.     

Structure and molecular conformation of tussah silk fibroin films: Effect of heat treatment

Structural changes of tussah (Antheraea pernyi) silk fibroin films induced by heat treatment were studied as a function of the treatment temperature in the range 200–250°C. The DSC curve of tussah films with α-helix molecular conformation displayed characteristic endo and exo peaks at 216 and 226°C, respectively. These peaks first weakened and then completely disappeared after heating at 230°C. Accordingly, the TMA thermal shrinkage at 206°C disappeared when the films were heated at 230°C. The onset of weight loss was monitored at 210°C by means of TG measurements. X-ray diffraction profiles gradually changed from α-helix to β-sheet crystalline structure as the treatment temperature increased from 200 to 250°C. On raising the heating temperature above 200°C, the intensity of IR and Raman bands characteristic of β-sheet conformation increased in the whole ranges of amide and skeletal modes. The sample treated at 200°C showed a spectral pattern intermediate between α-helix and β-sheet molecular conformation. The IR marker band for random coil structure, still detectable at 200°C, disappeared at higher treatment temperatures. Spectral changes attributable to the onset of thermal degradation appeared at 230°C. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 841–847, 1997     

Physical properties and phase separation structure of Antheraea pernyi/Bombyx mori silk fibroin blend films

The physical structure and compatibility of solution-cast Antheraea pernyi/Bombyx mori silk fibroin blend films were stuided by differential scanning calorimetry (DSC), thermomechanical (TMA) and thermogravimetric (TGA) analysis, dynamic viscoelastic measurement, infrared spectroscopy, and x-ray diffractometry. The DSC curves of the blend films showed independent endotherms at 280 and 358°C, corresponding to the thermal decomposition of B. mori and A. pernyi silk fibroins with random coil conformation. The intensity was roughly proportionate to the amount of each component in the blend. The thermal behavior corresponding to the conformational transitions induced by heating on A. pernyi and B. mori silk fibroins overlapped in the temperature range 190–230°C. Thermal expansion and contraction properties, as well as weight retention behavior of the blend films were intermediate between the pure components, as shown by the TMA and TGA curves. The onset temperature of the storage modulus curve decreased markedly, approaching that of B. mori silk fibroin film when the amount of this component in the blend increased. The loss modulus curve of the blend films showed two peaks at ca. 190 and 210°C, the former corresponding to B. mori, and the latter to A. pernyi silk fibroin. Infrared spectra of the blends exhibited absorption bands characteristic of the pure components overlapping in the spectral region 2000–400 cm^?1. The x-ray diffraction peaks at 23 and 21.5°, attributed to the crystalline spacings of A. pernyi and B. mori fibroins, respectively, overlapped in the diffraction curves of the blends, while the peak at 11.4°, of A. pernyi, increased as the content of this fibroin in the blend increased. The degree of crystallinity, calculated from the x-ray diffraction curves, diminished as the amount of B. mori silk fibroin decreased. A low degree of compatibility exists between the two fibroins when they are cast from aqueous solution in the experimental conditions adopted in this work. © 1994 John Wiley & Sons, Inc.     

Structure and molecular conformation of tussah silk fibroin films treated with water–methanol solutions: Dynamic mechanical and thermomechanical behavior

The thermal response of tussah (Antheraea pernyi) silk fibroin films treated with different water–methanol solutions at 20°C was studied by means of dynamic mechanical (DMA) and thermomechanical (TMA) analyses as a function of methanol concentration and treatment time. The DMA curves of α-helix films (treated with ≥80% v/v methanol for 2 min and 100% methanol for 30 min) showed the sharp fall of storage modulus at about 190°C, and the loss peak in the range 207–213°C. The TMA curves were characterized by a thermal shrinkage at 209–211°C, immediately followed by an abrupt extension leading to film failure. Both storage and loss modulus curves significantly shifted upwards for β-sheet films, obtained by treatment with ≤60% methanol for 30 min. The loss peak exhibited a maximum at 236°C. Accordingly, the TMA shrinkage at above 200°C disappeared. The films broke beyond 330°C, failure being preceded by a broad contraction step. Intermediate DMA and TMA patterns were observed for the other solvent-treated films. The loss peak shifted to higher temperature (219–220°C), and a minor loss modulus component appeared at about 230°C. This coincided with the onset of a plateau region in the storage modulus curve. The TMA extension–contraction events in the range 200–300°C weakened, and the samples displayed a final broad contraction (peak temperature 326–338°C) before breaking. The DMA and TMA response of these films was attributed to partial annealing by solvent treatment, which resulted in the formation of nuclei of β-sheet crystallization within the film matrix. The increased thermal stability was probably due to the small β-sheet crystals formed, which acted as high-strength junctions between adjacent random coil and α-helix domains. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2717–2724, 1998     

Physical characteristics and properties of waterborne polyurethane materials reinforced with silk fibroin powder

Degummed silk filament was pulverized with a home‐made machine to obtain silk fibroin (SF) powder, and the structure, morphology, and particle size of the SF powder were investigated. The individual spherical particles and aggregates with different morphology of silk fibroin coexisted in water. A waterborne polyurethane (WPU) aqueous dispersion was blended with the SF powder to prepare novel blended materials with improved physical properties. The average particle size and zeta potential of the WPU/SF aqueous dispersions were characterized. The result showed that the WPU/SF dispersion with higher SF content exhibited a less negative zeta potential and a larger average particle size. Furthermore, the effect of SF content on the morphology, miscibility, and mechanical properties of the resulting blended films was studied by scanning electron microscopy, wide‐angle X‐ray diffraction, dynamic mechanical thermal analysis, and tensile testing. The films showed an improved Young's modulus and tensile strength from 0.3 to 33.8 MPa, and 0.6 to 5.2 MPa, respectively, with the increasing of SF up to a content of 26 wt %. The negative charges in the periphery and the small particle size made a good effort on dispersing SF powder into the WPU matrix as small aggregates, and the SF powder led to the efficient strengthening of WPU materials. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 940–950, 2010     

Surface properties of silk fibroin films and their interaction with fibroblasts

There is a growing interest in the use of silk as a biomaterial for tissue engineering. Silk threads from Bombyx mori have a fibrous core of fibroin, the protein responsible for biocompatibility and bioactivity, which is surrounded by a family of "gummy" proteins, called sericins, which are almost completely removed during silk degumming. Three different methanol treatments on regenerated fibroin films were used to convert viscous solutions of Silk I to an insoluble crystalline form (Silk II), in an attempt to devise new processing protocols for the creation of a cell guiding fibroin surface. Human fibroblasts (MRC5 line) were used as probes of the cell-biomaterial interaction in the early stages of the process (1 h, 3 h, 6 h and 4 d after seeding). The effect of each treatment on cell adhesion, spreading and distribution was monitored by scanning electron microscopy (SEM) and was correlated to superficial properties (like roughness and crystallinity) and fibroin conformation by means of atomic force microscopy (AFM), used in both topographical and acoustic mode, and attenuated total internal reflection infrared spectroscopy (FTIR-ATR). It was found that traditional methanol treatments where fibroin films were soaked in methanol solution produced roughness patterns that affected only the very early stages of fibroblast adhesion (until 3 h from seeding), while the new treatment proposed could really dialogue with the cells. Its non-homogeneous surface can explain the existence of cells spreading in specific directions and the presence of cell repellent areas even 4 d after seeding.     

Conformation transition of silk fibroin induced by blending chitosan

The conformation of silk fibroin in silk fibroin/chitosan (SF/CS) blend membrane was analyzed by infrared spectrum, X-ray diffractometry, and Raman spectrum. The results demonstrated that the SF could show β-sheet conformation when the SF content in blend membranes was 10% (w/w) and 60–80% (w/w), while the pure SF membrane showed random coil conformation. A mechanism of the conformation transition was suggested in that the SF chain could use the rigid CS chain as a mold plate to stretch itself to form a β-sheet structure according to the strong hydrogen bond between CS and SF. Therefore, a new concept, named “Polymer-Induced Conformation Transition,” was proposed. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 2293–2296, 1997     

Structural changes of silk fibroin membranes induced by immersion in methanol aqueous solutions

Structural changes of native and regenerated silk fibroin membranes were induced by immersion in water-methanol solutions and examined as a function of immersion time and methanol concentration. X-ray diffractometry and infrared spectroscopy data showed that transition from random coil to β-sheet structure occurred favorably when both native and regenerated silk fibroin membranes were immersed in water-methanol solutions, regardless of the different immersion time. Only native silk membrane, treated for 2 min with pure methanol, maintained its original amorphous structure, as demonstrated by differential scanning calorimetric (DSC) curves. The degree of displacement, measured by thermomechanical analysis (TMA), was much greater for regenerated than for native silk fibroin membranes. SDS-PAGE pattern showed that native silk fibroin has a molecular weight of 350, while the regenerated sample is formed by a large number of polypeptides in the range of 200-50 KD. The amount of acidic and basic amino acids decreased slightly in regenerated silk fibroin. Physical properties of silk membranes treated with water-methanol solutions are discussed in terms of membrane structure, treatment conditions, and chemical structure of starting material. © 1994 John Wiley & Sons, Inc.     

Influence of an iodine treatment on the structure and physical properties of Bombyx mori silk fibroin fiber

Silk fibroin (SF) fiber from the Bombyx mori silkworm was treated with a 1.23 N iodine/potassium iodide (I₂–KI) aqueous solution, and the structure and physical properties were investigated to elucidate the effects of the iodine treatment. The SF fiber absorbed polyiodide ions such as I and I by immersion in the I₂–KI solution, and the weight gain of the SF fiber increased with the treatment time; it became saturated at about 20 wt % after 40 h. The results of the weight gain, Fourier transform infrared spectroscopy, and X‐ray diffraction measurements suggested that polyiodide ions mainly entered the amorphous region. Moreover, a new sharp reflection in the meridional direction, corresponding to a period of 7.0 Å, was observed and indicated the possibility of the formation of a mesophase structure of β‐conformation chains. Dynamic viscoelastic measurements showed that the molecular motion of the crystalline regions at about 220 °C was enhanced and shifted to lower temperature by the introduction of polyiodide ions. This indicated that the iodine component weakened the hydrogen bonding between the SF molecules forming the β‐sheet structure and caused molecular motion of the crystal to occur more easily with heating. With heating above 270 °C, the iodine component introduced intermolecular crosslinking to SF, and the melt flow of the sample was inhibited. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3418–3426, 2006     

Miscibility and biodegradability of silk fibroin/carboxymethyl chitin blend films

Blend films of silk fibroin and carboxymethyl chitin were prepared by solution casting using water as a cosolvent. The blend films were subjected to post-treatment with an aqueous methanol solution to induce beta-sheet formation of silk fibroin. The miscibility of the blend films both before and after methanol treatments was investigated in terms of chemical interactions, morphologies, thermal properties, and crystal structures by using FTIR spectroscopy, SEM, DSC, and XRD. The results indicate that the blend between silk fibroin and CM-chitin was semi-miscible because only the amorphous parts of the polymers were compatible with each other. The enzymatic degradation showed that the incorporation of CM-chitin enhanced biodegradability and swelling ability of silk fibroin.     

Atomic force microscopy: Bombyx mori silk fibroin molecules and their higher order structure

We performed atomic force microscopy measurements on fibroin molecules from the domestic silkworm, Bombyx mori. At low concentrations, we could observe single protein molecules. The shape of the observed molecules is a rod with long smaller chains extending from the ends. The size of the rod is 60 nm in length and 15 nm in width. At high concentrations, we observed long threadlike aggregates of fibroin molecules, their chains entangled with one another. These results provide insight into the microscopic mechanism of silk‐fiber formation. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1436–1439, 2000     

Thermal properties and phase transitions in blends of Nylon-6 with silk fibroin

The thermal and structural properties of binary blends of Nylon-6 (N6) and a chemically related biopolymer, Bombyx mori silk fibroin (SF), are reported in this work. Homopolymers and blends, in composition ratios of N6/SF ranging from 95/05 to 70/30, were investigated by thermogravimetric (TG) analysis, differential scanning calorimetry (DSC), Fourier transform infrared (FTIR) spectroscopy and wide angle X-ray scattering (WAXS). Silk fibroin typically degrades at temperatures just above 210°C, which occurs within the melting endotherm of N6. In TG studies, the measured mass remaining was slightly greater than expected, indicating the blends had improved thermal stability. No beta sheet crystals of SF were detected by FTIR analysis of the Amide I region. Strong interaction between N6 and SF chains was observed, possibly as a result of formation of hydrogen bonds between N6 and SF chains. DSC analysis showed that the addition of SF to N6 caused a decrease in the crystallization temperature, the melting temperature of the lowest melting crystals and the crystallinity of N6. Furthermore, the α-crystallographic phase dominates and the γ-crystallographic phase was not observed in N6/SF blends, in contrast to the homopolymer N6, which contains both phases. We suggest that the addition of SF might result in changes of the chain extension of N6, which lead to the appearance of α-rather than γ-phase crystals.     

Gelation behavior of Antheraea pernyi silk fibroin

The sol-gel transition behavior of Antherae pernyi silk fibroin(Ap-SF) has not been systematically investigated.In this work,the influence of environmental temperature,pH,the concentration of Ap-SF,K+ and Ca2+ on the gelation time,and the structural changes of Ap-SF in sol-gel transformation were studied.The results indicated that the gelation time of the Ap-SF aqueous solution decreased with the increase of the Ap-SF concentration and environmental temperature.The sol-gel transformation of Ap-SF was much m...     

Characterization of silk fibroin/hyaluronic acid polyelectrolyte complex (PEC) films

This study aimed the characterization of the films casted from the aqueous mixtures of the pH induced complexes between silk fibroin (SF) and hyaluronic acid (HA). The insoluble and transparent films were subjected to scanning electron microscopy (SEM) analyses to show the morphological changes. Thermal analysis of complex films was determined by a differential scanning calorimeter (DSC). The changes in the crystalline state were monitored by X-ray diffractometer (XRD) and Fourier transform infrared spectroscopy (FTIR). It was shown that the complexation between HA and SF was dominantly induced by pH. It was shown that the complex films comprised mixtures of crystalline and non-crystalline regions.     

1H pulsed NMR study of bombyx mori silk fibroin: Dynamics of fibroin and of absorbed water

The dynamical behavior of the Bombyx mori silk fibroin chain and of absorbed water in silk fiber, film, and powder has been studied by ¹H pulsed nuclear magnetic resonance (NMR). Segmental motions do not occur and only the rapid rotation of the methyl groups of alanine residues is observed from ?120 to 130°C. This is independent of the conformation or form of the silk fibroin samples. Magnetization of dry silk fibroin by the solid-echo method shows a single Gaussian decay, while two components are observed in the solid-echo signals of films containing 6–10 w/w% water. An immobile component with a T₂ value of 11 μs is attributed to silk fibroin, and the mobile component to bound water. The T₂ of the latter varies from 50 to 200 μs, depending on the sample. The dynamical behavior of water trapped in the film is discussed on the basis of these T₂ values.     

Structure and properties of composites compression‐molded from silk fibroin powder and waterborne polyurethane

The degummed silk filament was pulverized with a home‐made machine to obtain the silk fibroin (SF) powder with the diameter of around 3 µm. The resulting SF powder was blended with waterborne polyurethane (WPU) aqueous dispersion, and then was dried and compression‐molded to prepare novel blended materials with improved miscibility and mechanical properties. WPU acted as a plasticizer and one of the components for the blends during the compression‐molded process. The structure, morphology, and properties of the blended films were investigated. The results indicated that β‐sheet of SF existed in the blended films. The SEM images showed that the cross‐section of the blended films exhibited an overall homogeneous morphology. Furthermore, the transmission electron microscope observation exhibited that some sphere‐like SF particles were well dispersed in the WPU matrix. The hydrogen bond interaction between SF and WPU in the blended films led to an increase of the glass transition temperature for the soft segment of WPU in the blended films. The blended films showed an improved Young's modulus and tensile strength from 1.2 to 288.9 MPa and 0.3 to 16.5 MPa, respectively, with the increasing of SF up to a content of 70 wt%. The hydrogen‐bonding interactions existing in SF and WPU and compression molding method played the important role in improving the miscibility and mechanical properties of the blended films. Copyright © 2011 John Wiley & Sons, Ltd.     

Study on porous silk fibroin materials: 3. Influence of repeated freeze–thawing on the structure and properties of porous silk fibroin materials

The influence of repeated freeze–thawing on pore structural characteristics and physical properties of porous silk fibroin materials prepared by freeze drying were studied. It showed that when quick‐frozen silk fibroin solution was repeatedly thawed and frozen before being vacuum dried, thus pore size of prepared porous silk fibroin materials increased from 67 µm to about 120 µm, and pore density decreased from 80 per square millimeter to about 28 per square millimeter; at the same time compression ratio and moisture permeability increased from 22.7% and 230 g/m² hr to about 33.7% and 308 g/m² hr, respectively, tensile strength and dissolvability in hot water decreased from 20.2 N/cm² and 42.7% to about 12.5 N/cm² and 26.1%, respectively. Both the times of repeated thawing and the thawing temperature had a certain influence on the above‐mentioned pore characteristic parameters and physical properties. Copyright © 2001 John Wiley & Sons, Ltd.     

Fabrication of silk fibroin film with properties of thermal insulation and temperature monitoring

Silk fibroin exhibits excellent mechanical properties, good biocompatibility, and biodegradability combined with benign processing conditions, attracting considerable research interest for the application as biomedical materials. Among the diverse forms of sponges, hydrogels, films, and mats manufactured from silk fibroin, films are especially appealing due to the high water and oxygen permeability, good cell attachment, and low immunogenicity. Fabrication of silk fibroin films with novel properties has been successfully developed simply by incorporating various functional components into it. In the present study, the properties of thermal insulation and temperature monitoring for the silk fibroin film are demonstrated for the first time through the incorporation of thermochromic microcapsules within it. Moreover, the silk fibroin film is also endowed with improved mechanical properties in terms of tension strength and elongation at break because of the reinforcing effect of thermochromic microcapsules. The silk fibroin film fabricated with novel features in this study can be a good candidate for the application of wound dressings, tissue engineering scaffolds, and bio‐related devices in the future. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1846–1852     

Regenerated silk fibroin nanofibers: water vapor-induced structural changes and their effects on the behavior of normal human cells

Nanofibrous non-woven matrices were prepared by electrospinning a regenerated silk fibroin (SF) solution, and the structural changes of SF nanofibers treated with water vapor were investigated using time-resolved IR and (13)C CP/MAS NMR spectroscopy. Conformational transitions of SF from random coil to beta-sheet structures were induced by water vapor treatment and were strongly dependent on the treatment time and temperature. Water vapor treatment provided a useful means of stabilizing the SF nanofiber matrices, resulting in the formation of matrices with a decreased solubility in water and increased mechanical strength. The adhesion and spreading of both normal human keratinocytes and fibroblasts onto the SF nanofiber matrices were also investigated, and the water vapor-treated SF nanofiber matrices showed good cellular compatibility, in comparison with traditional methanol-treated ones. This approach to controlling the conformational changes of SF nanofibers by water vapor treatment may be useful in the design and tailoring of novel materials for biomedical applications, including wound dressings and scaffolds for tissue engineering.     

Non-bioengineered silk fibroin protein 3D scaffolds for potential biotechnological and tissue engineering applications

This paper describes a new source for fabricating high-strength, non-bioengineered silk gland fibroin 3D scaffolds from Indian tropical tasar silkworm, Antheraea mylitta using SDS for dissolution. The scaffolds were fabricated by freeze drying at different prefreezing temperatures for pore size and porosity optimization. Superior mechanical properties with compressive strength in the range of 972 kPa were observed. The matrices were degraded by proteases within 28 d of incubation. Biocompatibility was assessed by feline fibroblast culture in vitro and confocal microscopy further confirmed adherence, spreading, and proliferation of primary dermal fibroblasts. Results indicate nonmulberry 3D silk gland fibroin protein as an inexpensive, high-strength, slow biodegradable, biocompatible, and alternative natural biomaterial. [Figure: see text].