Ruptured conjugated polymer thin films formed during spin coating

The formation of ruptured poly[2‐methoxy‐5‐(2′‐ethyl‐hexyloxy)‐1,4‐phenyl vinylene] (MEH–PPV) thin films coated from undried tetrahydrofuran (THF) solutions was investigated. Because of the incompatibility of water and MEH–PPV, the polymer films coated from THF/water solutions showed a ruptured film structure. In the photoluminescence (PL) spectra of the polymer thin films, the ruptured polymer films showed a redshifted emission in comparison with continuous polymer thin films. According to a comparison of the PL spectra of polymer solutions and films, MEH–PPV in THF showed a coil–cylinder transition during precipitation from solution. Because of the incompatibility of water and MEH–PPV, an increase in the water content could increase the ratio of polymer chains in the cylinder conformation, resulting in a redshifted emission for the films. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 79–84, 2006     

Characterization of thin polymer‐like films formed by plasma polymerization of methylmethacrylate: A neutron reflectivity study

The microstructure of the plasma‐polymerized methylmethacrylate (ppMMA) films is characterized using neutron reflectivity (NR) as a function of the plasma reaction time or film thickness. Variation in the crosslink density normal to the substrate surface is examined by swelling the film with a solvent, d‐nitrobenzene (dNB). In the presence of dNB, uniform swelling is observed throughout the bulk as well as at the air surface, and silicon oxide interfaces. The results indicate that the MMA film prepared by plasma polymerization (ppMMA) has a uniform crosslink density from air surface to substrate surface. Additionally, the scattering length density of the plasma‐polymerized MMA film (SLD ≈ 0.750 × 10⁻⁶ Å⁻²) is much lower than that of a conventional PMMA film (SLD = 1.177 × 10⁻⁶ Å⁻²). The increase in film thickness following dNB sorption is 7.5% and at least 36% for the ppMMA and PMMA films, respectively. This suggests that the films formed by plasma polymerization are different from conventional polymers in chemical structure. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2522–2530, 2004     

Physical mechanisms responsible for the water-induced degradation of PC61BM P3HT photovoltaic thin films

We show that [6,6]-phenyl-C61-butyric acid methyl ester (PC₆₁BM) at the surface of thin film blends of poly(3-hexylthiophene) (P3HT):PC₆₁BM can be patterned by water. Using a series of heating and cooling steps, water droplets condense onto the blend film surface. This is possible due to the liquid-like, water swollen layer of poly(3,4-ethylenedioxythiophene) polystyrene sulfonate. Breath pattern water deformation and subsequent drying on the film surface results in isolated PC₆₁BM structures, showing that migration of PC₆₁BM takes place. This was confirmed by selective wavelength illumination to spatially map the photoluminescence from the P3HT and PC₆₁BM. Within a device, redistribution of the surface PC₆₁BM into aggregates would be catastrophic, as it would markedly alter device performance. We also postulate that repeated volume change of the poly(3,4-ethylenedioxythiophene) polystyrene sulfonate layer by water swelling may be, in part, responsible for the delamination failure mechanism in thin film solar cells devices. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 141–146     

Surfaces,thin films and patterning of spin crossover compounds

Spin crossover compounds are multifunctional switching materials that change their spin state and many other physical properties, such as colour, magnetic susceptibility, electric conductivity, dielectric constant and mechanical properties, upon external stimuli. Spin crossover materials have been proposed for a variety of technological applications that require the elaboration of highly controlled thin films and patterns. Here, we present a brief overview of the most diffused approaches for thin film growth and patterning, showing both conventional and unconventional approaches and the most recent advancement in their applications, highlighting the most promising cases and the most critical problems.     

Polyelectrolyte spin assembly: Influence of ionic strength on the growth of multilayered thin films

Layer-by-layer (LbL) assembly of polymer electrolyte multilayers is now a well-established method for the fabrication of thin films by sequential adsorption of alternating layers of oppositely charged polyelectrolytes. Most commonly, such adsorptions have been from quiescent solutions of varying ionic strength and pH. Here, we report results on an alternative processing route for the achievement of polymeric multilayer assemblies of poly(sodium-4-styrene sulfonate) and poly(allylamine hydrochloride) that utilizes conventional spin coating. We investigated and describe herein the dependence of multilayer film buildup on solution ionic strength for comparison with similar dependence in quiescent adsorption. Using UV-Vis spectroscopy we monitored the growth of the multilayered films, while with Atomic Force Microscopy (AFM) we examined the surface features and measured coating thicknesses at different salt concentrations. AFM and UV-Vis data reveal two regimes of behavior with increasing salt: strong salt-dependence at low salt contents, and weak salt-dependence for high salt contents. To explain this observation, we introduce the relevance of the dimensionless group De = τ, the local Deborah Number, to the problem. As ionic strength increases, τ increases so that spin-assembly flow influences adsorbed conformation, and thus LbL growth rate. Our results indicate the ability to design and control polyelectrolyte multilayered structures prepared via spin assembly by varying solution properties that influence the conformation of deposited polymer chains. Additionally, our studies reveal the need for study of the fundamental mechanisms of polyelectrolyte adsorption within complex flow fields. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3654–3666, 2004     

Charge transport properties of MDMO PPV thin films cast in different solvents

Charge transport properties in thin films of Poly(2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐1,4‐phenylenevinylene) (MDMO PPV) cast using either chloroform (CF), toluene (TOL), or chlorobenzene (CB) as solvent were investigated. Hole mobility (μ) in these thin films measured using time‐of‐flight transient photoconductivity showed an increasing trend with respect to the solvent used in the same order, that is, μ_CF (2.4 × 10^?7 cm²/Vs) < μ_TOL (6.9 × 10^?7 cm²/Vs) < μ_CB (2.3 × 10^?6 cm²/Vs). Observed variations in mobilities were attributed to different morphologies of MDMO PPV chains in thin films cast using the aforesaid solvents. Nature of the interchain interactions and aggregate formation were obtained using photoluminescence (PL), Raman spectroscopy, and AFM studies. Ratio of PL peak intensities of 0–0 and 0–1 transitions, which is a direct measure of interchain interaction, was the highest in CB and lowest in CF. Variation in the relative intensities of out‐of‐plane wagging of vinylene group (～963 cm^?1 mode) in Raman spectra suggested different extent of coiling of polymer chains in these thin films. From these observations, it was elicited that aggregate size and interchain interactions are highest in CB and least in CF. AFM‐based topographic images of thin films further supported these variations in the size of aggregates. Variation in the aggregate sizes and interchain interactions explained the corresponding variation in the mobility. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1431–1439     

Surface ordering in thin films of liquid‐crystalline polymers containing fluorinated and protonated segments: Neutron‐reflectometry study

Surface‐induced layering of fluorinated and protonated segments in thin films of a main‐chain liquid‐crystalline polymer, consisting of α‐methylstilbene, bridged by a fluorinated group was revealed by neutron reflectometry. The layering was driven by the difference in surface energy of the fluorinated and protonated segments and by the inherent ordering of the polymer. The lower‐surface‐energy fluorinated segments segregated to the air surface, and the protonated segments segregated to the SiO_x layer at the Si substrate. The ordering induced by the interface decayed into the film with a characteristic decay length of about 100 Å. The surface‐induced periodicity ranged from 15 to 20 Å, which is approximately equal to the molecular dimension of the repeating unit on the polymer backbone. The magnitude of segregation increased upon annealing in the liquid‐crystalline temperature range. The segregation was retained upon annealing above the bulk order–disorder transition temperature. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2817–2824, 2002     

极化中子衍射及在电子自旋密度研究中的应用

极化中子衍射方法常用于研究含未配对电子化合物中电子自旋密度的分布．分子中电子自旋密度分布从一个独特的角度反映化合物的磁性质．本文介绍极化中子衍射方法的背景知识和基本原理．包括中子源、中子和X射线衍射、极化中子衍射,以及一些常用的实验数据处理方法．选用几个实例总结了用极化中子衍射方法得到的电子自旋密度分布在无机和有机化学中的应用．通过单分子磁体[Fe8O2（OH）12（tacn）6]^8＋和氰基桥联化合物K2[Mn（H2O）2]3[Mo（CN）7]2·6H2O,说明如何用该方法研究金属原子间的磁相互作用;并通过Ru（acac）3这个只含一个未配对电子的化合物来说明如何获得化合物中金属和配体上小的自旋密度;最后介绍了该方法在nitronylnitroxide自由基研究中的应用．     

Scanning force microscopy study of the morphology of spin‐cast molecular‐imprinted nylon thin films

The morphology of thin, selectively imprinted films of Nylon‐6 was investigated by scanning force microscopy. Four amino acids were used as template molecules in the spin‐cast films. Film thickness ranged from 2 µm to 500 nm, depending on the nylon and template concentration in the casting solution. The thin‐film properties, including the presence of nanometer‐ to micrometer‐sized pores, are clearly associated with the imprinting process. The larger features observed by scanning force microscopy are attributed to amino acid clustering during the casting process. Copyright © 2004 John Wiley & Sons, Ltd.     

Facile deposition of high quality ferroelectric poly(vinylidene fluoride) thin films by thermally modulated spin coating

Direct deposition of high quality ferroelectric PVDF thin films using a modulated temperature spin coating method is demonstrated. The method is qualitatively guided from Flory‐Huggins theory of polymeric solutions and is general in applicability. Ferroelectric PVDF films with similar high structural and dielectric quality are deposited in environments ranging from 20 to 80% relative humidity on polar and non‐polar surfaces. The films do not show the presence of the non‐ferroelectric α‐phase. Resultant films have rms roughness values lower than 16 nm and remnant polarizations up to 6.5 µC cm^?2. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55 , 221–227     

Diffusion,evaporation, and surface enrichment of a plasticizing additive in an annealed polymer thin film

We present the first measurements of the simultaneous diffusion, surface enhancement, and evaporation of a plasticizer from a polymer, thin-film matrix using neutron reflection techniques. The reflectivity profiles as a function of the annealing time at an elevated temperature yield the time-dependent, plasticizer volume fraction profiles in a polyester–polyurethane (Estane) film. Thin, plasticizer-enriched layers form at both the polymer/substrate and polymer/air interfaces for annealed and unannealed samples. The diffusion equations for a material diffusing through a film and then evaporating into a vacuum at the free surface describe the loss of the plasticizer from the film for annealed samples. The loss of the plasticizer from the film is not limited by the movement of the plasticizer through the polymer matrix but is dominated by the plasticizer's rate of evaporation from the surface. The rate of evaporation and the volume fraction profiles for the plasticizer at the substrate interface are both consistent with surface attractions dominating over bulk attractions between the miscible plasticizer and the polymer. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3258–3266, 2004     

Interfacial profiles of miscible poly(4‐trimethylsilylstyrene)/polyisoprene bilayer films

Compositional profiles of bilayer films in the direction normal to the interfaces have been investigated by neutron reflectivity measurements and analyzed with mean field theory. The bilayer films were prepared with poly(4‐trimethylsilylstyrene) (PTMSS) and polyisoprene (PI), which constitute a miscible polymer pair and whose blends show phase separation at the lower critical solution temperature (LCST) by heating. Because we can accurately control the degree of polymerization of component polymers and can adjust the Flory–Huggins interaction parameter, χ, with the temperature, T, according to the relationship χ = 0.027–9.5/T, the phase behavior and the interfacial structure of PTMSS and PI are predictable by mean field theory. When the bilayer films of PTMSS and PI were set at 90 °C, which is a temperature below the LCST, diffusion at the interface was observed, and the original interface disappeared in several hours; this supports the idea that the polymer pair is miscible. No clear interfaces were identified below the LCST, whereas broad interfaces, compared with that of the strong segregation pairs, were observed above the LCST. The compositions of each layer are consistent with that of the coexisting phase in the polymer blends, and the interfacial widths agree well with the theoretical prediction considering the effect of capillary waves. In addition, all annealed films have a thin surface layer of PTMSS corresponding to surface segregation induced by the lower surface energy of PTMSS (with respect to that of PI). Thus, the interfacial profiles of PTMSS/PI bilayer films have been totally prospected in the framework of mean field theory. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1486–1494, 2005     

Determining the density profile of confined polymer brushes with neutron reflectivity

Polymer molecules at solid or fluid interfaces have an enormous spectrum of applications in a wide variety of technologies as lubricants, adhesion modifiers, and protective surface coatings. Because polymer brushes have great potential to be used in such applications, there is a need to determine their structure and efficiency in reduced spaces. Using neutron reflectivity, we have directly quantified the density distribution of opposing polymer brushes under confinement in good solvent conditions under confinement. Our measurements show that the density profile in the overlap region between opposing polymer brushes flattens, consistent with predictions from molecular-dynamics simulations. In addition, a significant increase in the density at the anchoring surfaces due to the collapse of the brush layers was observed. This collapse of the brushes in restricted geometries suggests that high-density brushes do not interpenetrate significantly under good solvent conditions. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3290–3301, 2004     

Spin coating process of sol-gel silicate films deposition: Effect of spin speed and processing temperature

The effect of two factors having the most important influence on spin coating process of sol-gel films: the spin speed and the temperature (of the substrate and the applied solution) during film deposition is discussed. It is shown, that film thickness and thickness uniformity are determined by centrifugal driving force dynamics, viscous polymer rheology, solvent evaporation dynamics, and film porous microstructure.     

Deuteration of molecules for neutron reflectometry on organic light-emitting diode thin films

Deuterated forms of aromatic charge transporting heterocycles 2 and 3 used in organic light-emitting diodes have been produced by hydrothermal reactions, catalyzed by Pt/C or Pd/C. Comprehensive analysis by mass spectroscopy, ¹H, ²H and ¹³C NMR enables determination of the overall quantity of D atoms present, as well as the level of deuteration at each molecular site. The roles of solubility and steric availability in deuteration are discussed in the light of these results. Neutron reflectometry indicates excellent scattering contrast between protonated and deuterated forms of these molecules, with nanoscale thin films showing the same density as in their bulk molecular forms. Although used for morphological studies of thin films typically used in OLEDs, the synthetic and analysis methods described here are generic and suitable for deuteration of other conjugated aromatic heterocycles and other optoelectronic devices.     

Atmospheric‐pressure spin plasma jets processing of polymethylmethacrylate surface using experimental design methodology

Atmospheric‐pressure spin plasma jets (APSPJs) have been developed to induce surface modifications on polymethylmethacrylate (PMMA). In this study, an experimental design methodology was used to investigate the influence of process parameters [such as radio frequency (RF) power, processing gap, and number of treatment cycles] on the characteristics of PMMA surface treated by APSPJs. It was observed from the atomic force microscope (AFM) and scanning electron microscope (SEM) results that the surface morphology of PMMA treated by direct plasma is much rougher than that treated by remote plasma. The direct plasma used in APSPJs processing created a substantial amount of nanostructure grains. Moreover, the measured XPS results showed that the O/C ratios of the PMMA surface were substantially increased and subsequently water contact angle decreased on direct plasma treatment. This decrease is due to an increase of oxygen‐containing functional groups on the PMMA surface by the APSPJs processing. From the statistical analysis, the RF power and the processing gap were found to play a major role in enhancing the hydrophilic properties of PMMA surface. In contrast, the number of treatment cycles played only a secondary role in this case. Finally, in this study the APSPJs processing was demonstrated to be an effective method for surface modification of PMMA by controlling processing parameters during the treatment process. Copyright © 2009 John Wiley & Sons, Ltd.     

Roughness correlation and interdiffusion in thin films of polymer chains

The surface morphology of thin bilayer polymer films on top of glass substrates was investigated. The bilayer consists of a blend film of protonated and deuterated polystyrene and an underlying deuterated polystyrene film. Choosing the thickness of the top film larger than 8 times and smaller than 2 times the radius of gyration of the chains enables the determination of film thickness and confinement effects. With diffuse neutron scattering at grazing incidence in the region of total external reflection, a depth sensitivity and a contrast even at the internal polymer–polymer interface was achieved. The underlying film is conformal to the substrate, and depending on the thickness of the top film two different types of roughness correlations are observed. Thin confined films nestle to the underlying polymer films, while the stiffness of thicker bulky films provides an independent morphology. In both cases, annealing above the glass-transition temperature yields an interdiffusion at the internal polymer–polymer interface, and the polymer–air surface remains essentially unchanged with respect to roughness correlations. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2862–2874, 1999     

Dynamics of thin polymer films: Recent insights from incoherent neutron scattering

Incoherent neutron scattering is presented as a powerful tool for interpreting changes in molecular dynamics as a function of film thickness for a range of polymers. Motions on approximately nanosecond and faster timescales are quantified in terms of a mean-square atomic displacement (〈u²〉) from the Debye–Waller factor. Thin-film confinement generally leads to a reduction of 〈u²〉 in comparison with the bulk material, and this effect becomes especially pronounced when the film thickness approaches the unperturbed dimensions of the macromolecule. Generally, there is a suppression (never an enhancement) of 〈u²〉 at temperatures T above the bulk calorimetric glass-transition temperature (T_g). Below T_g, the reduction in the magnitude of 〈u²〉 depends on the polymer and the length scales being probed. Polymers with extensive segmental or local mobility in the glass are particularly susceptible to reductions of 〈u²〉 with confinement, especially at the Q vectors probing these longer length scales, whereas materials lacking these sub-T_g motions are relatively insensitive. Moreover, a reduced 〈u²〉 value correlates with reduced mobility at long time and spatial scales, as measured by diffusion in these thin polymer films. Finally, this reduced thin-film mobility is not reliably predicted by thermodynamic assessments of an apparent T_g, as measured by discontinuities or kinks in the T dependence of the thermal expansion, specific volume, index of refraction, specific heat, and so forth. These measurements illustrate that 〈u²〉 is a powerful and predictive tool for understanding dynamic changes in thin polymer films. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3218–3234, 2004