Derivatization and determination of arsenic in marine samples by gas chromatography with electron capture detection

Summary Arsenic in marine samples was determined by gas chromatography with electron capture detection after derivatization with 2,3-dimercaptopropanol. Biological tissues and sediments were analyzed after acid decomposition. For sea water, arsenic was preconcentrated by coprecipitation with hydrous iron (III) oxide. The results obtained by this approach compare favourably with the certified values of the reference materials analyzed. Presented at the 15th International Symposium on Chromatography, Nürnberg, October 1984     

Static headspace and purge-and-trap gas chromatography for epichlorohydrin determination in drinking water

Epichlorohydrin (ECH) can enter drinking-water supplies due to leaching from epoxy resins in contact with water and/or through the use of flocculating water treatment agents. Potential human exposure from drinking waters poses a particular concern on account of toxicological studies showing severe acute and long-term toxic effects of ECH. Recently a parametric value of 0.1 μg/L for ECH in drinking water has been established by European Union.A few methods for ECH determination in water are available. However, they usually adopt cumbersome procedures for sample preparation and provide sensitivity not matching the EU criteria for water monitoring purposes.In this study we investigated the analytical performance of gas extraction techniques, such as static headspace (HS) and purge and trap (P&T), coupled to gas chromatography (GC) with an electron capture detector (GC-ECD) for the determination of ECH in drinking water. The influence of different parameters affecting the analytical response was studied in details in order to enhance the method sensitivity, thus fulfilling the regulatory requirements.The P&T GC-ECD method was proved capable of determining ECH in water for human consumption at a detection limit of 0.01 μg/L fully complying the regulatory levels. On the contrary, the HS GC-ECD method is far less sensitive (LOD≅40 μg/L) than the previous cited method. The P&T GC-ECD method is simple, rapid, automated, safe for operators and does not require large sample volumes. Therefore, it is useful for routine laboratory activities both for control and research actions.     

Multivariate optimization and validation of an analytical methodology by RP-HPLC for the determination of losartan potassium in capsules

This paper describes the optimization and validation of an analytical methodology for the determination of losartan potassium in capsules by HPLC using 2^5-1 fractional factorial and Doehlert designs. This multivariate approach allows a considerable improvement in chromatographic performance using fewer experiments, without additional cost for columns or other equipment. The HPLC method utilized potassium phosphate buffer (pH 6.2; 58 mmol L⁻¹)-acetonitrile (65:35, v/v) as the mobile phase, pumped at a flow rate of 1.0 mL min⁻¹. An octylsilane column (100 mm × 4.6 mm i.d., 5 μm) maintained at 35 °C was used as the stationary phase. UV detection was performed at 254 nm. The method was validated according to the ICH guidelines, showing accuracy, precision (intra-day relative standard deviation (R.S.D.) and inter-day R.S.D values <2.0%), selectivity, robustness and linearity (r = 0.9998) over a concentration range from 30 to 70 mg L⁻¹ of losartan potassium. The limits of detection and quantification were 0.114 and 0.420 mg L⁻¹, respectively. The validated method may be used to quantify losartan potassium in capsules and to determine the stability of this drug.     

Development of an analytical method based on microwave-assisted extraction and solid phase extraction cleanup for the determination of organochlorine pesticides in animal feed

A method to determine 21 organochlorine pesticides in animal feed samples using microwave assisted extraction and solid phase extraction cleanup was optimised regarding its main parameters. After extraction with hexane-acetone (50:50), three different sorbents (alumina/ENVI-Florisil, ENVI-Carb and ENVI-Carb II/PSA) were assayed for the cleanup step. Analytes were eluted with hexane-ethyl acetate (80:20) and determined by gas chromatography and electron capture detection followed by gas chromatography-mass spectrometry. ENVI-Carb and ENVI-Carb II/PSA provided colourless eluates but fewer interferent compounds were found in ENVI-Carb II/PSA chromatograms, so this system was selected to carry out the purification of the extracts. The analytical recoveries obtained with this method were close to 100% in most cases with relative standard deviations lower than 10%. These percentages were similar to those obtained with the Soxhlet extraction procedure, which shows the method suitable for the determination of organochlorine pesticides in animal feed material. The method was also validated with the analysis of a certified reference material (CRM-115 BCR), and the results obtained were in good accordance with the certified values.     

Quantitative determination of airbone C1- and C2-halocarbons by GC/ECD

The atmospheric levels of C₁- and C₂-halocarbons are determined by trapping on an adsorbent, thermodesorption, cryofocussing, gas chromatographic separation on a thick-film capillary, and electron-capture detection. The various aspects relevant to reliability and accuracy are discussed, such as type of adsorbent, range of detector response, and levels of contaminants present in blanks. These in turn have implications for optimum sample size and amount of adsorbent. The adopted method is suitable for routine analysis of airborne halocarbons at variable locations. The air concentrations of C₁- and C₂-halocarbons on the ground of mountain forests are similar to those in cities, a fact which supports the hypothesis that chlorocarbons are involved in the initiation of a phytotoxicological phenomenon commonly referred to as “forest decline”.     

Development and validation of an analytical method for multiresidue determination of pesticides in lettuce using QuEChERS–UHPLC–MS/MS

A new analytical method for multiresidue determination of 16 multiclass pesticides in lettuce was developed using ultra‐high performance liquid chromatography with tandem mass spectrometry with a triple quadrupole mass analyzer and positive mode electrospray ionization, using a previously optimized quick, easy, cheap, effective, rugged, and safe method for sample preparation. Validation studies, according to document SANTE/11945/2015, demonstrated that the developed method is selective, accurate, and precise, providing recoveries of 70–120%, relative standard deviations ≤20% and quantification limits from 3 μg/kg. The method was compared with one based on high‐performance liquid chromatography with tandem mass spectrometry, in terms of chromatographic performance, detectability and matrix effect for five varieties of lettuce. The new method provided a reduction in the time for the chromatographic analysis of 50%, from 30 to 15 min, using a lower mobile phase flow rate (0.147 mL/min), which reduced the consumption of mobile phase by 25%, and injection of smaller amounts of sample (1.7 μL). Lower limits of quantification were obtained for almost all pesticides studied for green‐leaf lettuce. However, in relation to the matrix effect, four of the five types of lettuce studied presented higher matrix effects.     

Extraction and determination of trace amounts of energetic compounds in blood by gas chromatography with electron capture detection (GC/ECD)

This paper describes an efficient and sensitive method for determining five energetic compounds at trace levels (ng/mL) in blood by gas chromatography with electron capture detection (GC/ECD). For seven test concentrations (1-1250 ng/mL), the average recoveries (%) were 104 ± 16, 108 ± 22, 105 ± 14, 100 ± 22 and 108 ± 16 for hexahydro-1,3,5-trinitroso-1,3,5-triazine (TNX), hexahydro-1,3-dinitroso-5-nitro-1,3,5-triazine (DNX), hexahydro-1-nitroso-3,5-dinitro-1,3,5-triazine (MNX), hexahydro-1,3,5-trinitro-1,3,5-triazacyclohexane (RDX) and 2,4,6-trinitrotoluene (TNT) (n = 84), respectively. Analysis of DNX and RDX produced lower precision than other energetic compounds. Acetonitrile extracts of blood samples should be analyzed immediately as the test compounds can transform into unknown compounds, which lowered the recovery by 0-45% within 10 days at room temperature (∼20 °C). Maintaining sample extracts at 4 °C decreased loss of test compounds. The method described herein was validated by different analysis teams on different days. Two-way ANOVA indicated that there was no significant difference between analysis teams or days of analysis. The method was successfully employed in the analysis of blood samples from a mouse dosing study involving TNX and RDX.     

Comparison of GC-ECD,GC-MS and GC-AED for the determination of polychlorinated biphenyls in highly contaminated marine sediments

Summary Electron capture detection (ECD), low- and highresolution mass spectrometry (LR- and HRMS), and atomic emission detection (AED) were compared for the gas chromatographic (GC) detection of polychlorinated biphenyls (PCBs) present in highly contaminated marine sediments. With ECD, LRMS, and even HRMS, detection was seriously disturbed by the complex matrix of the sediments, whereas AED in the chlorine-selective mode provided excellent PCB profiles without interferences. In addition, GC-AED provided congener independent responses, which enabled accurate quantitation of all PCBs based on a single calibration curve. However, because GC-AED was less sensitive than the other techniques studied, preparation of relatively large amounts of sample (10–20 g dry sediment) was required for most analyses.     

Development of a methodology based on headspace-gas chromatography-ion mobility spectrometry for the rapid detection and determination of patin fish oil adulterated with palm oil

The present research intends to develop a new method based on headspace-gas chromatography-ion mobility spectrometry (HS-GC-IMS) for the detection and determination of patin fish oil adulterated with different percentages of palm oil, because it is a cheaper vegetable oil. Five variables that affect headspace generation (incubation time and temperature, amount of sample, injection volume, and pre-heating time) have been optimized by means of a Box Behnken design in combination with Response Surface Methodology. Then, repeatability and intermediate precision have been studied where coefficients of variation lower than 10% were obtained. This new method has been applied to several samples of patin fish oil adulterated with palm oil at 20 different levels (5–50% palm oil content). The results have confirmed the suitability of the HS-GC-IMS for a rapid, easy, and reliable detection and discrimination of adulterated oil samples since a characteristic fingerprint that allows 100% successful discrimination between adulterated and unadulterated patin oil samples was achieved. Finally, a regression model has been developed to determine each sample’s adulteration level with an error lower than 10% and a coefficient of determination greater than 0.95.     

Development of an improved analytical method for the determination of carcinogenic polycyclic aromatic hydrocarbons in transformer oil

Polynuclear aromatic hydrocarbons (PAHs) are natural constituents of transformer oils and are essential in prolonging transformer in-service lifetime. Issues concerning PAH carcinogenicity demand methods that provide qualitative and quantitative information on the PAH composition of new and in-service oils to allow informed operational decisions to be made. However, current analytical methods focus on PAH fingerprinting, as opposed to quantitative analysis and are also cumbersome, relying on the use of large (>100 ml) volumes of organic solvents, some of which are hazardous. This paper reports a method for the improved quantification of carcinogenic PAHs in transformer oils that is both simple and repeatable. The method uses commercially available solid-phase extraction columns and millilitre volumes of relatively non-hazardous solvents. Extraction efficiencies of > or =74% were obtained for the Environmental Protection Agency priority PAHs. The method has potential for automation and high-throughput analysis and thus is of interest to industries that use transformer oils.     

Toxaphene analysis in Great Lakes fish: a comparison of GC-EI/MS/MS and GC-ECNI-MS, individual congener standard and technical mixture for quantification of toxaphene

Toxaphene is considered to be a problematic organochlorine pollutant because of its bioaccumulation potential and persistence in aquatic environments. In this study, whole lake trout and walleye composites were used to evaluate two analytical techniques for total toxaphene and selected congener analysis. The efficacy of using gas chromatography electron ionization tandem mass spectrometry (GC-EI/MS/MS) and electron capture negative ionization mass spectrometry (GC-ECNI-MS) were compared. Although the sensitivity using GC-ECNI-MS was approximately five times greater than GC-EI/MS/MS, the latter provided more consistent inter-Parlar relative response factors (RRF). When using technical calibration mixtures, these results suggest a more accurate total toxaphene measurement was obtained using the GC-EI/MS/MS method. Total toxaphene concentrations in lake trout composites from both methods were highly correlated (R ² = 0.985) with the MS/MS concentrations approximately half of those determined by ECNI, suggesting systematic high bias in toxaphene concentrations when measured using GC-ECNI.     

Determination of chlorobenzenes in pure,tap, and sea water by static headspace gas chromatography‐electron capture detection

A simple, efficient, solvent‐free, and commercial readily available approach for determination of 11 chlorobenzenes (CBs) in water samples using the static headspace (HS) sampling and gas chromatography‐electron capture detector has been described. The proposed static HS sampling method was initially optimized and the optimum experimental conditions found were 10 mL water sample containing 20% (w/v) sodium chloride placed in a 20 mL vial and stirred at 70°C for 30 min. The linearity of the method ranged from 0.16 to 8.0 μg/L for dichlorobenzene isomers, 0.0176～0.88 μg/L for trichlorobenzene isomers, 0.004～0.2 μg/L for tetrachlorobenzene isomers, and from 0.001 to 0.05 μg/L for pentachlorobenzene and hexachlorobenzene, with correlation coefficients ranging between 0.9992 and 0.9999. The limits of detection were in the low μg/L level, ranging between 0.0002 and 0.04 μg/L. The relative recoveries of spiked CBs with external calibration or standard addition method at different concentration levels in pure, tap, and sea water samples were 83～116%, 89～108%, and 93～112%, respectively, and with relative standard deviations of 1.9～6.3%, 1.6～5.4%, and 2.5～5.7% (n = 5), respectively. It is concluded that this method can be successfully applied for the determination of CBs in pure, tap, and sea water samples.     

Sensitive determination of perfluorocarbon tracers in air by intermediate trapping and GC-ECD analysis

This paper reports on the development of a simple method for the determination of two perfluorinated hydrocarbons (C₇F₁₄ and C₈F₁₆) in air down to 0.2 ng/m³, for long range atmospheric tracer experiments. The organic vapors are adsorbed on graphitized carbon black, desorbed thermally and determined by capillary GC-ECD at subambient temperature. Optimization of the experimental conditions is described. The tracers were tested in a field experiment where SF₆ was also released and the agreement was satisfactory.     

Multiresidue determination of organochlorines in fish oil by GC-MS: A new strategy in the sample preparation

A rapid, economic and environmentally friendly analytical methodology has been implemented for the determination of α-, β-, γ- and δ-HCH, p,p′-DDT, p,p′-DDD and p,p′-DDE, PCBs congeners #28, #52, #101, #153, #138 and #180 and Hexachlorobenzene in fish oil. 1,2,3,4-Tetrachloronaphtalene was used as internal standard. The sample preparation, consisting of a single step of clean-up and fractionation, took place in a column filled with different layers of neutral and sulphuric acid modified silica. The analytes were eluted by vacuum with of hexane. Significant reduction in terms of solvents, sorbents, and analysis time was achieved in comparison with literature.Gas chromatography coupled to mass spectrometry was used for the separation and determination of the analytes. The instrumental limits of detection were from 0.1 to 1.3 ng mL⁻¹ and the response of the detector was linear up to 200 ng mL⁻¹. The separation proved to be precise (RSD < 3.7% in peak area) and robust in terms of peak area, peak efficacy and resolution. The methodology was validated with two certified reference materials of cod liver oil, BCR 598 and BCR 349, obtaining no statistically significant differences between the concentrations found and certified. For the analytes that were not certified, aliquots of the reference materials were spiked and the recoveries obtained were satisfactory. These results were consistent with those found previously for DDTs by gas chromatography with an electron-capture detector.The methodology was applied to the analysis of three fish oil pills sold in Spain as a dietary supplement of vitamins and omega-3 fatty acids. The sum of the analytes studied was from 64 to 80 ng g⁻¹. The most abundant compounds are PCBs, followed by DDTs in all samples.     

毛细管气相色谱法测定牛奶中有机氯和有机磷农药残留量

采用一个较快速、简单的方法测定牛血中有机氯和有机磷农药残留物。牛奶中农残经氯仿萃取和固相提取净化后，分别用气相色谱－电子捕获检测器和气相色谱－火焰光度检测器直接测定，色谱柱为ＨＰ－１接ＨＰ－５、ＤＢ１７大口径石英毛细管柱。本法对１７种有机氯农残的回收效率范围为７１．２％￣９９．７％，检测限为０．５￣９μｇ／ｋｇ。而１１种有机磷农残的回收率范围为７０．１％￣９６．１％，检测限则为０．０１￣０．０４ｍ     

Environmentally friendly solid‐phase microextraction coupled with gas chromatography and mass spectrometry for the determination of biogenic amines in fish samples

In this work, a facile and environmentally friendly solid‐phase microextraction assay based on on‐fiber derivatization coupled with gas chromatography and mass spectrometry was developed for determining four nonvolatile index biogenic amines (putrescine, cadaverine, histamine, and tyramine) in fish samples. In the assay, the fiber was firstly dipped into a solution with isobutyl chloroformate as derivatization reagent and isooctane as extraction solvent. Thus, a thin organic liquid membrane coating was developed. Then the modified fiber was immersed into sample solution to extract four important bioamines. Afterwards, the fiber was directly inserted into gas chromatography injection port for thermal desorption. 1,7‐Diaminoheptane was employed as internal standard reagent for quantification of the targets. The limits of detection of the method were 2.98–45.3 μg/kg. The proposed method was successfully applied to the detection of bioamines in several fish samples with recoveries ranging 78.9–110%. The organic reagent used for extraction was as few as microliter that can greatly reduce the harm to manipulator and environment. Moreover, the extraction procedures were very simple without concentration and elution procedures, which can greatly simplify the pretreatment process. The assay can be extended to the in situ screening of other pollutant in food safety by changing the derivatization reagent.     

Method validation for the determination of propellant components by Soxhlet extraction and gas chromatography/mass spectrometry

A fast, sensitive, and accurate GC/MS method for the quantification of aliphatic nitroesters (ethylene glycol dinitrate, nitroglycerin, and triethylene glycol dinitrate) and aromatic amines (diphenylamine, 2-nitrodiphenylamine, and triphenylamine) in propellants was developed and validated. This method comprises a Soxhlet extraction step with dichloromethane, followed by separation on a capillary column MDN-5. Ionization of the analytes is carried out using electron ionization. The limit of quantification of the method was 1% w/w for aliphatic nitroesters and 0.1% w/w for aromatic amines (diphenylamine and triphenylamine). Values of repeatability and reproducibility for analyzed compounds were smaller than values of the maximum allowed tolerances of the Horwitz-equation RSD(max) and 2/3 RSD(max). Values of accuracy for selected compounds were below the acceptable threshold of 15% for all tested levels in the range of calibration curve excepting the lowest concentration of calibration curve for nitroglycerin and aromatic amines. During the validation of method, temperature instability in injection port of gas chromatograph and column was observed for 2-nitrodiphenylamine. Hence, it follows worse results of accuracy and linearity and 2-nitrodiphenylamine was not validated successfully.     

Development and validation of a gas chromatography-mass spectrometric method for the determination of sildenafil and desmethyl-sildenafil in whole blood

Sildenafil (SDL) is a phosphodiesterase type 5 inhibitor and it is approved for the treatment of erectile dysfunction and pulmonary hypertension. SDL is extensively metabolized to its pharmacologically active metabolite, desmethyl‐sildenafil (DSDL). A sensitive and specific GC/MS method for the determination of SDL and DSDL in whole blood was developed and validated to support therapeutic drug monitoring of SDL patients. The combination of solid‐phase extraction with derivatization using BSTFA with 1% TMCS in acetonitrile efficiently reduced matrix effect and improved sensitivity of the method. In this assay, protriptyline was used as internal standard for both analytes. The LODs were 1.50 and 5.00 ng/mL for SDL and DSDL, respectively, whereas the respective LOQs were 5.00 and 15.0 ng/mL. The calibration curves were linear up to 500.0 ng/mL (SDL: R² 0.992, DSDL: R² 0.990). Absolute recovery values for both analytes ranged from 83.1 to 93.2%. Within‐ and between‐batch accuracy was less than 11.8 and 10.2%, respectively, whereas within‐ and between‐batch precision was less than 8.1 and 10.8%, correspondingly. The developed method is suitable for the determination of SDL and DSDL concentrations in blood samples obtained from patients under Viagra^® treatment, for pharmacokinetic studies or for the investigation of related forensic cases.     

Gas-chromatographic fatty-acid fingerprints and partial least squares modeling as a basis for the simultaneous determination of edible oil mixtures

Partial least squares modeling and gas-chromatographic fatty-acid fingerprints are reported as a method for the simultaneous determination of cottonseed, olive, soybean and sunflower edible oil mixtures. In this work, two sets of three- and four-component combinations of oils were prepared, hydrolyzed and the obtained free fatty acids analyzed by gas chromatography (GC) without any further derivatization. The normalized percentages of the myristic (14:0), palmitic (16:0), palmitoleic (16:1), stearic (18:0), oleic (18:1), linoleic (18:2) and linolenic (18:3) acids were chromatographically measured in samples and used for constructing calibration matrix. The cross-validation method was used to select the number of factors and the proposed methods were validated by using two sets of synthetic oil mixture samples. The relative standard error for each oil in mixture samples was less than 10%. This approach allows determining possible adulteration in each of the four edible oils.