The removal efficiency of chestnut shells for selected pesticides from aqueous solutions

The removal of selected pesticides such as carbofuran (CF) and methyl parathion (MP) using low-cost abundant sorbent chestnut shells from aqueous solutions has been investigated in the present study. The sorption parameters, i.e., contact time, pH, initial pesticide solution concentration and temperature have been studied. Maximum percent sorption (99+/-1%) was achieved for (0.38-3.80) x10(-4) and (0.45-4.5) x10(-4) mol dm(-3) of MP and CF pesticide solutions respectively, using 0.4 g of sorbent in 100 ml of solution for 30 min agitation time at pH 6. The Freundlich, Langmuir and Dubinin-Radushkevich (D-R) models have been applied, and their constants for methyl parathion and carbofuran, sorption intensity 1/n (0.55+/-0.02 and 0.54+/-0.04), multilayer sorption capacity C(m) (28.3+/-0.5 and 16.4+/-0.7) x10(-3) mol l(1-1/n)dm(3/n)g(-1), monolayer sorption capacity Q (22.5+/-0.5 and 10.8+/-0.3) x10(-6) mo lg(-1), binding energy, b (2.9+/-0.2 and 5.2+/-0.5) x10(4) dm(3)mol(-1), and sorption energy E (11.2+/-0.1 and 11.5+/-0.2 kJ mol(-1)) have been evaluated respectively. Lagergren, Morris-Weber and Reichenberg equations were employed to study kinetics of sorption process. Thermodynamic parameters DeltaH (-5.09+/-0.1 and 22.8+/-0.4 kJ mol(-1)), DeltaS (-4.33+/-0.0003 and 0.09+/-0.001 kJ mol(-1)K(-1)) and DeltaG((303K)) (-2.9 and -3.8 kJ mol(-1)) have been calculated for methyl parathion and carbofuran, respectively. The developed sorption procedure has been employed to environmental samples.     

Chitosan/UiO-66 composites as high-performance adsorbents for the removal of methyl orange in aqueous solution

UiO-66 and chitosan/UiO-66 composites were successfully synthesized by varying the mass addition of chitosan which were 0%, 2.5%, 5%, 10%, and 20% of the mass of UiO-66, denoted as UiO-66, Cs(2.5)/UiO-66, Cs(5)/UiO-66, Cs(10)/UiO-66, and Cs(20)/UiO-66, respectively. UiO-66 was modified with chitosan using the impregnation process. The X-ray diffraction patterns of the synthesized materials showed characteristic peaks at 2θ of 7.25° and 8.39°, which matched to that of the reported UiO-66. In addition, the Fourier transform infrared spectroscopy spectra of the materials showed absorption bands at the same wavenumber as UiO-66 and chitosan previously reported. The surface morphology of UiO-66 observed from scanning electron microscopy images was in the form of agglomerated small cube particles, where the smaller particles were observed for Cs(10)/UiO-66. From the N₂ adsorption isotherms, it was found that the Brunauer-Emmett-Teller surface areas of UiO-66, Cs(5)/UiO-66, and Cs(10)/UiO-66 materials were 825.7 m²/g, 835.4 m²/g, and 882.2 m²/g, respectively. The results of the study on adsorption of methyl orange in aqueous solutions showed that Cs(5)/UiO-66 had the highest adsorption capacity of 370.37 mg/g and followed the pseudo–second-order adsorption kinetic with a Langmuir isotherm model.     

Conducting polymer/alumina composites as viable adsorbents for the removal of fluoride ions from aqueous solution

The polyaniline/alumina (PANi-AlO) and polypyrrole/alumina (PPy-AlO) composites were prepared and characterized by FT-IR, SEM and X-ray diffraction studies and were employed as adsorbents for the removal of fluoride ions from aqueous solution by the batch sorption method. The amount of fluoride ions adsorbed per unit mass of the adsorbents was observed to be higher than that by the individual constituents. The maximal amount of adsorption is 6.6 mg/g for PANi-AlO and for PPy-AlO it is 8 mg/g. The Langmuir and Freundlich isotherms were used to describe adsorption equilibrium. The kinetics of the adsorption process was investigated using Natarajan-Khalaf equation and intraparticle diffusion model. FT-IR and XRD pattern of the adsorbent, before and after the adsorption is recorded to get better insight into the mechanism of the adsorption process. The results of equilibrium and spectral investigations revealed that the mechanism of fluoride ion removal by these composites involve both the formation of aluminium-fluoro complexes on the alumina surface and doping/dopant-exchange of fluoride ions in the polymer.     

Raw and treated marble wastes reuse as low cost materials for phosphorus removal from aqueous solutions: Efficiencies and mechanisms

Phosphorus removal from synthetic solutions by raw and calcined powdered marble wastes (RPMW and CPMW) has been investigated in batch mode under different experimental conditions. The results showed that RPMW and CPMW have high removal efficiencies, especially in acidic media. The maximum phosphorus removal capacities were evaluated to 103.9 and 181.2 mg·g⁻¹ at an initial pH and an aqueous concentration of 5 and 350 mg·L⁻¹, respectively. Phosphorus removal by RPMW occurred mainly through adsorption. However, for CPMW, phosphorus was removed not only by adsorption, but also by precipitation as calcium phosphate complexes. Specific analyses using scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction and Fourier transform infrared spectroscopy confirmed that this precipitate is most probably hydroxyapatite. On the other hand, CPMW have demonstrated an important ability in removing phosphorus from highly concentrated dairy wastewater (C_0,P = 1000 mg·L⁻¹) since only one dosage of 10 g·L⁻¹ was enough to ensure more than 97% of phosphorus removal.     

AloeVera as an effective biosorbent for the removal of thorium and barium from aqueous solutions

Journal of Radioanalytical and Nuclear Chemistry - The use of three biosorbents based on AloeVera wastes for the removal of thorium and barium from aqueous solutions (Cinit:...     

Collective small-amplitude proton motions in the hydration shells of aqueous alcohol solutions

Hydrophobic hydration in aqueous solutions of ethanol, isopropanol and t-butanol is analyzed from the collective character of the OH stretching Raman spectrum. The data suggest that the network structure of water in the hydration shells is not significantly perturbed by either ethanol or isopropanol, in contrast to t-butanol, which exhibits an enhancement of the structure similar to that previously observed in aqueous solutions of the semiclathrate, tetra-n-butylammonium hydroxide.     

Stability of metallic materials in aqueous and aqueous-glycol solutions

The corrosion behavior of aluminum, steel, and pig iron in fresh water, ethylene glycol, and waterglycol mixtures containing 5–95 vol % fresh water in the temperature range 20–100°C was studied. The influence of temperature on the corrosion rate of the metals was examined in relation to the composition of aqueous ethylene glycol solutions.     

Carboxyl-functionalized nanoparticles with magnetic core and mesopore carbon shell as adsorbents for the removal of heavy metal ions from aqueous solution

This communication demonstrates superparamagnetic nanosized particles with a magnetic core and a porous carbon shell (thickness of 11 nm), which can remove 97% of Pb(2+) ions from an acidic aqueous solution at a Pb(2+) ion concentration of 100 mg L(-1). It is suggested that a weak electrostatic force of attraction between the heavy metal ions and the nanoparticles and the heavy metal ions adsorption on the mesopore carbon shell contribute most to the superior removal property.     

Preliminary selection of clay minerals for the removal of pharmaceuticals,bisphenol A and triclosan in acidic and neutral aqueous solutions

Pharmaceuticals, personal care products and endocrine disruptors demonstrate huge potential to cause adverse ecological health effects at very low concentration in aquatic environment. There is a need to improve current purification technologies used in sewage and drinking-water treatment plants. This article aims at providing new insights into the recent development of natural and modified clay-based sorbents for the removal of aqueous contaminants such as pharmaceuticals and personal care products. The removal of six widely used pharmaceuticals: ibuprofen, diclofenac, ketoprofen, carbamazepine, as well as endocrine disrupting chemicals – bisphenol A and a bactericidal agent, triclosan – was examined by sorption onto eight adsorbents. Sorption was performed using natural and modified clay minerals – montmorillonite (Mt), vermiculite (VER), bentonite (B), kaolinite (K), commercial acid activated montmorillonites K10 and K30, and two carbonaceous-mineral nanocomposites, MtG5%T, BAlG3%C. This study showed that among the tested natural clays, vermiculite is the most promising sorbent for the removal of pharmaceuticals in purification processes. Among the modified clay minerals, the best results were achieved for carbonaceous bentonite and two acid activated montmorillonites K10 and K30. However, the removal of acidic pharmaceuticals on montomorillonite K10 and carbonaceous bentonite was strongly dependent on the pH value. In the case of vermiculite and acid-modified montmorillonite K30, the sorption of the selected compounds was not significantly affected by pH, which is crucial in wastewater treatment. The sorption constant divided by the specific surface area (K_d/A) is proposed to assess whether the surface area or chemical properties of the materials control the sorption process. K_d/A values were relatively high in the case of vermiculite, so it should be noticed that individual and specific surface properties of vermiculite were of crucial importance for sorption.     

Cellulose nanocrystals as promising adsorbents for the removal of cationic dyes

Cellulose nanocrystals (CNCs) prepared from cellulose fibre via sulfuric acid hydrolysis was used as an adsorbent for the removal of methylene blue (MB) from aqueous solution. The effects of pH, adsorbent dosage, temperature, ionic strength, initial dye concentration were studied to optimize the conditions for the maximum adsorption of dye. Adsorption equilibrium data was fitted to both Langmuir and Freundlich isotherm models, where the Langmuir model better described the adsorption process. The maximum adsorption capacity was 118 mg dye/g CNC at 25 °C and pH 9. Calculated thermodynamic parameters, such as free energy change (ΔG = ?20.8 kJ/mol), enthalpy change (ΔH = ?3.45 kJ/mol), and entropy change (ΔS = 0.58 kJ/mol K) indicates that MB adsorption on CNCs is a spontaneous exothermic process. Tunability of the adsorption capacity by surface modification of CNCs was shown by oxidizing the primary hydroxyl groups on the CNC surface with TEMPO reagent and the adsorption capacity was increased from 118 to 769 mg dye/g CNC.     

Chitin and chitosan as chromatographic supports and adsorbents for collection of metal ions from organic and aqueous solutions and sea-water

The rates of adsorption of several metal ions on chitin and chitosan in water and sea-water have been measured; chitin and chitosan are proposed as Chromatographic chelating supports. These natural polymers are also suitable for recovery of trace metals from sea-water.     

Polanyi-based models for the adsorption of naphthalene from aqueous solutions onto nonpolar polymeric adsorbents

In this research, naphthalene was adopted as the representative model compound of PAHs, and static adsorption of naphthalene from aqueous solution onto three commercial polymeric adsorbents with different pore structure was investigated. Nonlinear isotherms models, i.e., Freundlich, Langmuir, and Polanyi-Dubinin-Manes (PDM) models were tested to fit experimental data, and the experimental data were found to fit well by the PDM model. Through both isotherm modeling and constructing "characteristic curve," Polanyi theory was useful to describe the adsorption process of naphthalene by polymeric adsorbents, providing evidence that a micropore filling phenomenon was involved during the adsorption process. In addition, a good linear correlation was obtained between the naphthalene adsorption capacities and the micropore volume of adsorbents (Vmicro), whereas no linear relationship was found between the naphthalene adsorption capacities and the specific surface area of adsorbents. Based on the PDM model, the micropore volumes of adsorbents was introduced to normalize the equilibrium adsorbed volume (qv), plots of qv/V(micro) vs adsorption potential density for naphthalene on three different polymeric adsorbents were collapsed to a single correlation curve, which would be of great benefit to predict the adsorption capacity of adsorbent for the purpose of adsorption engineering design.     

Laterite clay-based geopolymer as a potential adsorbent for the heavy metals removal from aqueous solutions

This study is focused on the investigation of low iron lateritic clay-based geopolymer as a potential adsorbent for the higher uptake of Ni(II) and Co(II) ions from aqueous solutions. BET analysis revealed that the sieved geopolymer sample (SGS) was characterized by 17.441 m²/g of surface area, 0.005 cm³/g of pore volume, and 13.549 Å of pore diameter. SEM investigation confirmed the presence of pores and cavities onto the surface of SGS. XRD analysis showed that the geopolymer is semi-crystalline in nature. It was found that the adsorption ability of SGS remained 520 mg/g for Ni(II) ions and 500 mg/g for Co(II) ions when 0.5 M solutions were stirred with SGS for 60 min. The temperature and pH of the solution were maintained at 60 °C and 7.0, respectively. The adsorption data of both heavy metal (HM) ions fitted best in the pseudo-second-order kinetic model. The low activation energy value i.e. 2.507 kJ/mol for Ni(II) ions and 2.286 kJ/mol for Co(II) ions confirmed adsorption is physisorption. Adsorption data were tested with Langmuir and Freundlich models, the data showed comparatively better fitting in the Freundlich model. The greater value of monolayer adsorption capacity (Xm) for Ni(II) ions was found 1.77 × 10⁻² mol/g while for Co(II) ions it remained 1.69 × 10⁻² mol/g confirming the better interaction of metal ions with the adsorbent surface. Negative values of ΔG° confirmed the spontaneity of the process while the positive value of ΔS° showed the randomness of adsorbate particles. The positive value of ΔH° showed that the adsorption process remained endothermic for both HM ions. The experimental results confirmed the ability of laterite clay-based geopolymer for better removal of HM ions and hence can be employed for the wastewater treatment processes at low-cost adsorbent.     

Comparison of adsorbents for the preconcentration of sulfanilamides from aqueous solutions prior to HPLC determination

We studied the adsorption of sulfanilamide, sulfamethazine, sulfamethoxazole, sulfamethoxypyridazine, and sulfachloropyridazine on hypercrosslinked polystyrene, polymer adsorbents Strata-X and Strata SDB-L, carbon nanomaterial Taunit, and Diasorb-100-C₁₆T depending on the acidity of the solution and the concentration of adsorbates. Conditions were optimized for the preconcentration of sulfanilamides on a microcolumn packed with hypercrosslinked polystyrene. The compounds were desorbed with 1 mL of acetonitrile and determined in the eluate by reversed-phase HPLC with spectrophotometric detection at 255 nm. The preconcentration step decreases the detection limits for sulfanilamides by more than 60 times (to 3 ng/mL). The procedure was used for the analysis of a model mixture in river water.     

Formation and removal of alkylthiolate self-assembled monolayers on gold in aqueous solutions

We report the development of novel reagents and approaches for generating recyclable biosensors. The use of aqueous media for the formation of protein binding alkylthiolate monolayers on Au surfaces results in accelerated alkylthiolate monolayer formation and improvement in monolayer integrity as visualized by fluorescence microscopy and CV techniques. We have also developed an electrocleaning protocol that is compatible with microfluidics devices, and this technique serves as an on-chip method for cleaning Au substrates both before and after monolayer formation. The techniques for the formation and dissociation of biotinylated SAMs from aqueous solvents reported here may be applied towards the development of Au-based sensor devices and microfluidics chips in the future. A potential use of these devices includes the specific capture and triggered release of target cells, proteins, or small molecules from liquid samples.     

Polyelectrolyte shells of copolymer micelles in aqueous solutions: a Monte Carlo study

Multimolecular micelles, formed by polystyrene-block-poly(methacrylic acid) in water, are studied by lattice Monte Carlo method. Electrostatic interactions are calculated in the mean-field approximation by solving the Poisson-Boltzmann equation. The model is parametrized according to available experimental data. The dependence of micellar size on pH and ionic strength is calculated and compared with experimental data. A special attention is devoted to the behavior in solutions with a low ionic strength.     

Electrochemical oxidative modification of nanocarbon materials in aqueous electrolyte solutions

The effect exerted by electrochemical oxidative modification of carbon nanofibers and nanotubes by anodic and successive cathodic and anodic polarization in aqueous solutions of electrolytes H₂SO₄, CH₃COONH₄, HNO₃, (NH₄)₂SO₄, [H₂SO₄ + (NH₄)₂SO₄] on the structure and morphology of the fibers constituting the nanomaterials, on the composition of surface groups, on the stationary electrode potential of carbon nanofibers, and on properties of epoxy–carbon composites was studied. The results of the electrochemical modification were compared to the results of chemical modification of carbon nanofibers in a 6.0 M HNO₃ solution and of carbon nanotubes in a mixture of concentrated acids H₂SO₄ + HNO₃.