Removal, preconcentration and determination of Mo(VI) from water and wastewater samples using maghemite nanoparticles

Removal and recovery of Mo(VI) from aqueous solutions were investigated using maghemite (γ-Fe₂O₃) nanoparticles. Combination of nanoparticle adsorption and magnetic separation was used to the removal and recovery of Mo(VI) from water and wastewater solutions. The nanoscale maghemite with mean diameter of 50 nm was synthesized by reduction coprecipitation method followed by aeration oxidation. Various factors influencing the adsorption of Mo(VI), e.g. pH, temperature, initial concentration, and coexisting common ions were studied. Adsorption reached equilibrium within <10 min and was independent of initial concentration of Mo(VI). Studies were performed at different pH values to find out the pH at which maximum adsorption occurred. The maximum adsorption occurred at pHs between 4.0 and 6.0. The Langmuir adsorption capacity (q_max) was found to be 33.4 mg Mo(VI)/g of the adsorbent. The results showed that nanoparticle (γ-Fe₂O₃) is suitable for the removal of Mo(VI), as molybdate, from water and wastewater samples. The adsorbed Mo(VI) was then desorbed and determined spectrophotometrically using bromopyrogallol red as a complexation reagent. This allows the determination of Mo(VI) in the range 1.0–86.0 ng mL⁻¹.     

介孔二氧化硅纳米球对水中Mo(VI)的吸附研究

本研究制备了介孔二氧化硅纳米球(MSN),并用之吸附脱除水中的Mo(VI)。应用扫描电镜、介孔分析仪、红外光谱等对MSN进行了表征。考察了pH、吸附时间、MSN投加量和温度对水中Mo(VI)脱除率的影响,并在单因素试验基础上通过正交试验法确定了Mo(VI)的最佳脱除条件：pH=3,MSN投加量为 8.5g/L,吸附时间为36h。在优化吸附试验条件下MSN对加标水中Mo(VI)的脱除率为93.6% ~ 97.3%。     

A Copper(II) Ion‐Selective Potentiometric Sensor Based on N,N′,N″,N′′′‐Tetrakis(2‐pyridylmethyl)‐1,4,8,11‐tetraazacyclotetradecane in PVC Matrix

The simple PVC‐based membrane containing N,N′,N″,N′′′‐tetrakis(2‐pyridylmethyl)‐1,4,8,11‐tetraazacyclotetradecane (tpmc) as an ionophore and dibutyl phthalate as a plasticizer, directly coated on a glassy carbon electrode was examined as a new sensor for Cu²⁺ ions. The potential response was linear within the concentration range of 1.0×10^?1–1.0×10^?6 M with a Nernstian slope of 28.8 mV/decade and detection limit of 7.0×10^?7 M. The electrode was used in aqueous solutions over a wide pH range (1.3–6). The sensor exhibited excellent selectivity for Cu²⁺ ion over a number of cations and was successfully used in its determination in real samples.     

N,N,N′,N′‐Tetraalkylaminoazoxybenzene Derivatives; Convenient Synthesis and Mechanistic Study

N,N,N′,N′‐tetraalkyaminoazoxybenzene derivatives were conveniently prepared by the coupling of N,N‐dialkylnitrosoaniline in the presence of acetone and KOH. The reaction mechanism was proposed and investigated, and the structure of compound 3b was also confirmed by single crystal X‐ray diffractometry.     

Direct voltammetric determination of Mo(VI) in plants: the need for a multivariate study of interferences

A multivariate modelling procedure using a second order composite design showed that the adsorptive stripping voltammetry (AdSV) technique used for molybdenum determination in a N,N-dimethylformamide (DMF)-ethanol-water homogeneous ternary solvent system (HTSS) using α-benzoinoxime (αBO) as the complexing agent and a sodium acetate-acetic acid buffer as the supporting electrolyte is much more tolerant to the presence of phosphorous (as phosphate) and iron than it could be presumed. Instead of the concentration ratios of P/Mo=100 and Fe/Mo=500, determined by univariate experiments, these values were respectively raised to 97,500 and 4200 when the phosphate and Fe(III) levels are varied simultaneously from 0.625 to 2.500 and from 0.006 to 0.150 mg l⁻¹, respectively, in the voltammetric cell, keeping the molybdenum concentration constant at 3.00 μg l⁻¹. This allowed us to propose a straightforward AdSV-HTSS procedure for the determination of Mo(VI) in plants. The AdSV results compared favourably with those obtained by using graphite furnace atomic absorption spectrometry (GFAAS) and with the results of samples from the International Plant-Analytical Exchange (IPE) programme of Wageningen University (The Netherlands).     

Kinetic Determination of Trace Amounts of Cu(II) in Water Based on its Catalytic Effect on the Reaction of Mercaptosuccinic Acid and Cr(VI)

 A kinetic method is presented for the determination of Cu(II) in water. It is based on the catalytic effect of Cu(II) on the oxidation of mercaptosuccinic acid by chromate in acidic media. The extent of the reaction is followed spectrophotometrically at 345 nm and pseudo-first order rate coefficients are determined as a function of catalyst concentration. The optimum operating conditions regarding ionic strength, temperature and concentration of reagents were established. Interference by several ionic species was studied and the effects of Fe(III) and Pb(II) were suppressed by complexation with pyrophosphate. Calibration lines were obtained for both low (30–640 μg · l⁻¹) and high (640–1500 μg · l⁻¹) catalyst concentrations. The relative standard deviation for 625 μg · l⁻¹ Cu(II) is 6.1% (n = 5). The detection limit is 22 μg · l⁻¹. The method was applied to real samples of river water of the mining region of Baia-Mare, Northern Romania. The results were compared to those obtained by an officially standardized AAS method. Good agreement was attained. The method is inexpensive, fairly rapid and sensitive. Moreover, its working range covers the exact range of concentrations usually encountered in the mentioned geographic area. Received July 28, 2000; accepted December 10, 2001; published online June 24, 2002     

Spectrophotometric Determination of Rhenium(IV) with Thiocyanate,TX-100 and N,N′-Diphenylbenzamidine

A spectrophotometric method to determine rhenium(IV) at trace level is based on the extraction of Re(IV)-SCN^? complex in sulphuric acid media with N,N′-diphenylbenzamidine(DPBA) in presence of a non-ionic surfactant triton X-100 (TX-100) in chloroform. The complex shows maximum absorbance at 435 nm with amolar absorptivity value of 4.24 × 10⁴ L mol^?1 cm^?1 at an acidity range 3.5-6.5 M H₂SO₄. The method followed Beer's Law for the system Re(IV)-SCN^?(TX-100)-DPBA upto 4.0 μg Re(IV) mL^?1. The detection limit of the method is 5 ppb. None of the tested foreign ions, except molybdenum(VI), interfere with the determination of rhenium. The interference due to molybdenum could effectively be removed by prior precipitation with oxine. The effect of various analytical parameters on the extraction of the metal are discussed.     

Highly stable electrochromic polyamides based on N,N‐bis(4‐aminophenyl)‐N′,N′‐bis(4‐tert‐butylphenyl)‐1,4‐phenylenediamine

A new triphenylamine‐containing aromatic diamine monomer, N,N‐bis(4‐aminophenyl)‐N′,N′‐bis(4‐tert‐butylphenyl)‐1,4‐phenylenediamine, was synthesized by an established synthetic procedure from readily available reagents. A novel family of electroactive polyamides with di‐tert‐butyl‐substituted N,N,N′,N′‐tetraphenyl‐1,4‐phenylenediamine units were prepared via the phosphorylation polyamidation reactions of the newly synthesized diamine monomer with various aromatic or aliphatic dicarboxylic acids. All the polymers were amorphous with good solubility in many organic solvents, such as N‐methyl‐2‐pyrrolidinone (NMP) and N,N‐dimethylacetamide, and could be solution‐cast into tough and flexible polymer films. The polyamides derived from aromatic dicarboxylic acids had useful levels of thermal stability, with glass‐transition temperatures of 269–296 °C, 10% weight‐loss temperatures in excess of 544 °C, and char yields at 800 °C in nitrogen higher than 62%. The dilute solutions of these polyamides in NMP exhibited strong absorption bands centered at 316–342 nm and photoluminescence maxima around 362–465 nm in the violet‐blue region. The polyamides derived from aliphatic dicarboxylic acids were optically transparent in the visible region and fluoresced with a higher quantum yield compared with those derived from aromatic dicarboxylic acids. The hole‐transporting and electrochromic properties were examined by electrochemical and spectro‐electrochemical methods. Cyclic voltammograms of the polyamide films cast onto an indium‐tin oxide‐coated glass substrate exhibited two reversible oxidation redox couples at 0.57–0.60 V and 0.95–0.98 V versus Ag/AgCl in acetonitrile solution. The polyamide films revealed excellent elcterochemical and electrochromic stability, with a color change from a colorless or pale yellowish neutral form to green and blue oxidized forms at applied potentials ranging from 0.0 to 1.2 V. These anodically coloring polymeric materials showed interesting electrochromic properties, such as high coloration efficiency (CE = 216 cm²/C for the green coloring) and high contrast ratio of optical transmittance change (ΔT%) up to 64% at 424 nm and 59% at 983 nm for the green coloration, and 90% at 778 nm for the blue coloration. The electroactivity of the polymer remains intact even after cycling 500 times between its neutral and fully oxidized states. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2330–2343, 2009     

Micellar effect on the sensitivity of spectrophotometric Mo(VI) determination based on the formation of gallic acid complex providing evidence for the polyoxoanion structure of molybdate ions

In this study effects of anionic (sodium dodecyl sulfate, SDS), cationic (cetyltrimethylammonium bromide, CTAB) and nonionic (Triton X-100, TX100) micelles on the sensitivity of spectrophotometric molybdenum(VI) (Mo) determination based on the formation of a binary complex with gallic acid (GA) were investigated.

Micellar CTAB was found to enhance the formation of Mo–GA complex. SDS micelles exerted an inhibitory effect while TX100 micelles had no effect on the complex formation. By the optimization of experimental conditions, the determination limit of the method suggested in the literature was lowered from 5.2 × 10⁻⁵ to 4.6 × 10⁻⁶ and to 5.7 × 10⁻⁷ M, in the absence and presence of CTAB, respectively.

The mechanism of the effect of CTAB was investigated by spectrophotometric titrations and it was concluded that CTAB did not form a ternary complex with Mo and GA. The stoichiometry of the complex, deduced from the results of spectrophotometric titrations, provided evidence for the formation of para-Mo₇O₄⁶⁻ polyanions at pH 4.5, indicating to the formation of a charge transfer complex between these ions and GA in micellar medium.     

Semiempirical INDO/S calculations on the absorption spectrum of mono‐ and trinuclear vanadium(II) complexes

This work is concerned with prospective starting materials for the synthesis of larger molecules used as functional models of the substrate binding and reducing site of the vanadium nitrogenase. It is well known that the mononuclear adduct of vanadium(II) chloride with N,N,N′,N′‐tetramethylethylenediamine, henceforth referred to as [VCl₂(tmeda)₂], is a good starting material for the synthesis of trinuclear vanadium complexes. We now report the results of semiempirical calculations on the spectroscopy of [VCl₂(tmeda)₂] using the intermediate neglect of differential overlap (INDO) method. For the mononuclear complex, the ground state was calculated to be a quartet, about 45 kcal/mol below the doublet. For the positively charged trinuclear vanadium complex, [V₃(μ‐Cl)₃(μ₃‐Cl)₂(tmeda)₃]⁺, the ground state was calculated to be a decatet, about 47 kcal/mol below the octet. For both complexes the frontier orbitals are dominated by the vanadium 3d manifold, and accordingly the electronic spectra are dominated by d‐d* excitations within this manifold. The INDO/S‐calculated spectra are in good agreement with the observed UV‐visible spectra in both cases. © 2002 Wiley Periodicals, Inc. Int J Quantum Chem 88: 245–251, 2002     

Reactions of N-(N′,N′,N″,N″-tetramethyl)guanidinyl-substituted Phosphines with Organoelement Chlorides involving Phosphorus,Sulfur, and Selenium; Formation of Stable Phosphino-, Thio-, and Selenophosphonium Salts

By reaction of N-(N′,N′,N″,N″-tetramethyl)guanidinyl-substituted phosphines with diorganochlorophosphines, organodichlorophosphines, p-tolylsulfenylchloride and phenylselenylchloride a variety of stable phosphonium chlorides with a P–E (E = P, S, Se) bond were obtained. In one case, performing this reaction in the presence of sodium tetraphenylborate led to the corresponding phosphonium tetraphenylborate. All compounds were characterised by multinuclear NMR and elemental analysis. The selenophosphonium chloride 4 a of the trihydrate was further characterised by a single crystal X-ray analysis. The P–Se bond is very long [193.0(3), 193.3(3) pm in two independent fomula units]. The water molecules and the chloride anions form hydrogen bonded layers.     

Synthese,Struktur und einige Reaktionen [N-(N′,N′,N″,N″-tetramethyl)-guanidinyl]-substituierter Phosphorylverbindungen

Synthesis, Structure, and some Reactions of N-(N′,N′,N″,N″-tetramethyl)guanidinyl-substituted Phosphoryl Compounds The tetramethylguanidinyl-substituted phosphoryl compounds 1 – 10 were prepared in the reaction of the appropriate chlorophosphoryl compounds with either N′,N′,N″,N″-tetramethylguanidine (HTMG) or N-trimethylsilyl-(N′,N′,N″,N″-tetramethyl)guanidine (TMSTMG). With methyl iodide 1 reacted with N-alkylation to give the ammonium salt 11. 1 reacted with BF₃ · Et₂O at both imino nitrogen atoms with formation of the bis-BF₃-adduct 12 . The X-ray structure determination of phenylphosphonic acid-bis(N′,N′,N″,N″-tetramethylguanidinide) 3 shows shortened PN-bonds and widened PNC-angles, consistent with the partial double bond character of the PN-bond.     

Crystal structure of (N,N,N′,N′-tetramethyl-1,2-diaminoethane)(1,1,1-trifluoro-6-methyl-2,4-heptanedionato)copper(II) perchlorate

The solvatochromic compound [Cu(tfmh)Me₄en]ClO₄ (tfmh^? denotes the anion of 1,1,1-trifluoro-6-methyl-2,4-heptanedione) was prepared and its structure has been determined from three-dimensional X-ray diffraction data. The structure consists of discrete [Cu(tfmh)Me₄en]⁺ monomeric units and perchlorate ions. The copper(II) ion is surrounded by the two nitrogen atoms of the diamine molecule and the two oxygen atoms of the β-dionato anion. The N,N,N′,N′-tetramethyl-1,2-diaminoethane, Me₄en, coordinates as bidentate ligand through the nitrogen atoms and adopts the gauche conformation and λ configuration. The CuN₂O₂ chromophore is virtually planar. The compound crystallizes in the monoclinic system (space group P2₁/c) with a = 11.9520(2), b = 14.6600(2), c = 17.2240(4) Å, β = 135.72(2)°, Z = 4 and V = 2107.01(7) ų.     

Determination of Solvatochromic Regression Coefficients for the Molybdenum(VI) Complex with Ethylenediamine‐N,N′‐diacetic Acid by Using Kamlet‐Abboud‐Taft Equation

The Solver, Microsoft Excel 2000 powerful optimization package, has been used to perform non‐linear least‐squares curve fitting on the basis of Gauss‐Newton method for the calculation of solvatochromic regression coefficients for the complexation of molybdenum(VI) with ethylenediamine‐N,N′‐diacetic acid and dissociation constants at 25°C and constant ionic strength 0.1 mol·L⁻¹ sodium perchlorate in different aqueous solutions of methanol. A combination of potentiometric and UV spectrophotometric methods have been used for experimental studies. Non specific and specific solute‐solvent interactions were interpreted by correlating the equilibrium data with solvent parameters using the Kamlet‐Abboud‐Taft solvatochromic equation. Finally the influence of the solvent on the stability of the complex was discussed on the basis of the correlation results and the contribution of α (hydrogen‐bond donor acidity), β (hydrogen‐bond acceptor basicity) and π* (dipolarity/polarizability) parameters.     

Polarographic behaviour of 2-benzilidenimino-benzohydroxamic acid (2-BIBH) and 2-BIBH-Mo(VI) system

The polarographic behaviour of 2-benzilideniminobenzohydroxamic acid (2-BIBH) solutions and of 2-BIBH solutions in the presence of Mo(VI) have been studied by using differential pulse polarography and cyclic voltammetry. The polarographic characteristics of the resulting waves have been studied and possible mechanisms of the processes involved have been proposed. A linear relationship has been observed betweenI _p and Mo(VI) concentration in the range 2×10^–6 to 1.6×10^–5 M when using 3×10^–4 M 2-BIBH. Standard deviations of 5.6×10^–8 and 1.2×10^–8 M were found for 3×10^–6 and 8 × 10^–6 M Mo(VI), respectively.     

ESR studies of photosensitized degradation of poly(L‐lactic acid) via photoionization of dopant

The photosensitized degradation of poly(L ‐lactic acid) (PLA) via an anionic reaction process was studied using spectrophotometry, electron spin resonance (ESR), and gel permeation chromatography (GPC) measurements. PLA film doped with N,N,N′,N′‐tetramethyl‐p‐phenylenediamine (TMPD) was irradiated at 77 K using UV light (λ_c = 356 nm) by which the PLA matrix itself cannot be directly excited. After photoirradiation, a new broad absorption band appeared over the original spectrum due to TMPD⁺ ·, which was produced by two‐photon ionization. The ESR spectrum of the irradiated sample indicated the presence of the TMPD⁺ · radical and main‐chain scission radical of PLA. During the thermal annealing at 0 °C, the latter radical changed to another radical species by dehydrogenation of the alpha hydrogen of the PLA main chain. TMPD⁺ · was extremely stable at room temperature for 7 d. However, by thermal annealing at 40 °C, all the radicals decayed due to the enhanced molecular motions near T_g of PLA (58.7 °C). Spectral simulation for the obtained ESR spectra revealed the relative amounts of four radicals: TMPD⁺ ·, a main‐chain scission radical, a main‐chain tertiary radical, and an unknown radical. The last one was tentatively assigned to the PLA radical anion because of its short decay time. GPC measurements clearly indicated a decrease in the molecular weight of PLA after irradiation. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 706–714, 2001     

Study on the Reaction of Proteins with 5＇-Nitrosalicylfluoronemolybdenum（VI） Complex by Spectrophotometry in PVA 124 Microemulsion

The application of 5′‐nitrosalicylfluorone (5′‐NSF)‐molybdenum(VI) complex as a spectroscopic probe was studied. In the buffer medium of HOAc‐NaOAc at 3.45 and in the presence of PVA 124 microemulsion, 5 '‐NSF‐Mo(VI) complex combines protein rapidly to form a stable compound. leading to an absorbance decrease at 525 nrn of 5′‐NSF‐Mo(VI) complex. According to this change, microdetermination of protein has been described. Bovine serum albumin (BSA) could be determined in the linear range of 0–16 pg*mL with the detection limit of 11 ng*mL^?1. Many amino acid and metal ions studied do not interfere with the assay. The method possesses high sensitivity as well as high selectivity. It can be used to determine protein in human urine and milk powder successfully. The relative standard deviations are in all instances less than 4.7%. and the recoveries are between 97.6% and 106.0%. Moreover, the binding number of BSA with the complex, which is determined by using molar ratio, Rosenthal graphic and slope ratio methods, is in good agreement with each other.     

Synthese von Magnesium-bis[N,N′-bis(trimethylsilyl)benzamidinat] als Bis(THF)- und Benzonitril-Addukt

Synthesis of Magnesium Bis[N,N′ -bis(trimethylsilyl)benzamidinate] as both Bis(THF) and Benzonitrile Adduct Magnesium bis[bis(trimethylsilyl)amide] 1 , reacts with benzonitrile in toluene at room temperature to yield magnesium bis[N,N′-bis(trimethylsilyl)benzamidinate]-benzonitrile(1/1) 2 . Addition of THF leads to a quantitative substitution of the benzonitrile ligand by two THF molecules. The performance of the addition reaction in THF yields magnesium bis[N,N′-bis(trimethylsilyl)benzamidinate] · THF(1/2) 3 . The upper benzonitrile complex 2 , crystallizes in the orthorhombic space group Pbcn with {a = 1383.2(2); b = 2589.1(4); c = 1133.7(1) pm; Z = 4}. The magnesium atom is coordinated distorted trigonal-bipyramidal, where the benzonitrile ligand lies within the equatorial plane. The axial bound nitrogen atom of the benzamidinate substitution shows with a value of 213 pm a slightly longer bond distance to the metal center than the one in the equatorial plane (210 pm). The steric strain within the benzamidinate ligand leads to an elongation of the silicon atoms out of the 1,3-diazaallylic moiety under an enlargement of the C? N? Si angle to 131°.     

N,N,N′,N′,N″‐penta(methyl acrylate)diethylenetriamine: A novel ligand for atom transfer radical polymerization of methyl methacrylate

A novel ligand, N,N,N′,N′,N″‐penta (methyl acrylate) diethylenetriamine (MA₅‐DETA), was synthesized by the reaction of diethylenetriamine with methyl acrylate in almost quantitive yield. The polymerizations of methyl methacrylate with MA₅‐DETA as the ligand and α,α‐dichlorotoluene (DCT) and ethyl 2‐bromoisobutyrate (2‐EBiB) as the initiators, respectively, under different conditions were examined. The polymerization with CuCl/MA₅‐DETA/DCT was closely controlled in bulk and gave polymers with quite narrow molecular weight distributions (M_w/M_n's) of 1.16–1.29. The polymerization with the system CuBr/MA₅‐DETA/EBiB in bulk gave high activity. However, the system was not well controlled and gave the polymers with M_w/M_n = 1.35–1.53. The solution polymerization in anisole with CuBr/MA₅‐DETA/EBiB showed a better‐controlled nature. Moreover, the addition of CuBr₂ into the aforementioned system can further improve its controllability. The M_w/M_n's of the resulting polymers ranged from 1.11 to 1.21. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1963–1969, 2004     

Strontium- und Barium-bis[N,N′ -bis(trimethylsilyl)benzamidinate] aus der Additionsreaktion der Erdalkalimetall-bis[bis(trimethylsilyl)amide] mit Benzonitril

Strontium and Barium Bis[N,N′-bis(trimethylsilyl)benzamidinates] from the Addition Reaction of the Alkaline Earth Metal Bis[bis(trimethylsilyl)amides] and Benzonitrile The reaction of strontium bis[bis trimethylsilyl)amide] with benzonitrile yields strontium bis[N,N′- bis(trimethylsilyl)benzamidinate] · 2THF, which crystallizes in the orthorhombic space group Pbcn (a = 1845.4(3); b = 131 1,3(2); c = 1838,(3) pm; Z = 4). During the similar reaction of barium bis[bis(trimethylsilyl)amide] with benzonitrile the benzonitrile adduct barium bis[N,N′-bis(trimethylsilyl)benzamidinate] · 2 THF · benzonitrile is formed. After the addition of diphenylacetylene to the strontium di(benzamidinate) in diglyme a clathrate of the composition strontium bis[N,N′-bis(trimethylsilyl)benzamidinate] · diglyme · diphenylacetylene could be isolated; the spectroscopic data as well as the X-ray structure (monoclinic, C2/c, a = 1492.2(2); b = 1539.1(2); c = 2337.8(3)pm; Z = 4) confirm the isolated appearance of the acetylene molecule without interaction to the metal center in solution and in the solid state, respectively.