Use of a microcolumn packed with modified carbon nanofibers coupled with inductively coupled plasma mass spectrometry for simultaneous on-line preconcentration and determination of trace rare earth elements in biological samples

In this work, a new method was developed for the determination of trace rare earth elements (REEs) in biological samples by inductively coupled plasma mass spectrometry (ICP-MS) after preconcentration on a microcolumn packed with modified carbon nanofibers (CNFs). CNFs oxidized with nitric acid have been proved to possess an exceptional adsorption capability for REEs due to their surface functionalization. The effects of the experimental parameters, including pH, sample flow rate and volume, elution solution and interfering ions, on the recoveries of the analytes have been investigated systematically. A 100-fold enrichment factor was obtained. The adsorption capacity of CNFs was found to be 18.1, 19.3, 23.6, 17.6, 22.3 and 19.5 mg/g for La, Ce, Sm, Eu, Dy and Y, respectively. Under the optimum conditions, the detection limits of this method ranged from 0.2 pg/mL (Dy) to 1.2 pg/mL (Ce) with an enrichment factor of 15-fold, and the relative standard deviations (RSDs) for the determination of REEs at the 1.0 ng/mL level were less than 4% (n = 9). This method was applied to the analysis of trace REEs in a real sample of human hair with recoveries of 95-115%. In order to validate the proposed method, a certified reference material of human hair (GBW 07601) was analyzed with satisfactory results.     

Nanometer-sized zirconium dioxide microcolumn separation/preconcentration of trace metals and their determination by ICP-OES in environmental and biological samples

A new method is proposed using a microcolumn (20 mm × 2.0 mm) packed with nanometer-sized zirconia as solid-phase extractor for the separation/preconcentration of Mn, Cu, Cr, Zn, Ni and Co prior to their determination by inductively coupled plasma optical emission spectrometer (ICP-OES) in environmental samples. The factors affecting the separation and preconcentration of analytes such as pH, sample flow rate and volume, eluent concentration and volume were determined, interfering ions were studied, and the optimal experimental conditions were established. The adsorption capacity of nanometer-sized ZrO₂ for Mn, Cu, Cr, Zn, Ni and Co was found to be 1.3, 1.3, 1.7, 2.0, 3.9 and 1.5 mg g⁻¹, respectively. The detection limits of the method were 12, 58, 24, 2, 7 and 36 ng L⁻¹, respectively, with a preconcentration factor of 25. The precision of this method was 1.7% (Mn), 2.9% (Cu), 5.9% (Mn), 3.8% (Mn), 6.2% (Mn) and 4.3% (Mn) with 9 determinations of 10 ng mL⁻¹ of target analytes, respectively. The method was successfully applied to the determination of trace metals in lake water, dried fish samples, certified reference materials of human hair and milk, and provided satisfactory results.     

Electrothermal atomic absorption spectrometric determination of lead in high-purity reagents with flow-injection on-line microcolumn preconcentration and separation using a macrocycle immobilized silica gel sorbent

A fully automated procedure for the determination of ng l⁻¹ amounts of lead has been developed using flow injection (FI) online column preconcentration coupled with electrothermal atomic absorption spectrometry (ETAAS). The proposed FI manifold and its operation make possible the introduction of the total eluate volume into the graphite atomizer, avoiding the necessity for optimization of subsampling the eluate. The interference of other heavy metal ions due to competition for active sites of the sorbent is overcome using a highly selective macrocycle immobilized on silica gel (Pb-02). Lead is adsorbed on a microcolumn (50 μl) packed with Pb-02, and after washing the column with dilute nitric acid, air is introduced to remove all solution from the column and connecting tubing. The sorbed analyte is then eluted quantitatively into the graphite tube atomizer, preheated to 100°C, with 36 μl of ETDA solution (0.035 mol l⁻¹, pH 10.5), propelled by air in order to minimize dispersion. The collection efficiency was 77% and with a sample loading flow rate of 3 ml min⁻¹ and a 60 s preconcentration time, the enhancement factor was 77 and the throughput was 17 samples per hour. The relative standard deviation (n = 10) at the 300 ng l⁻¹ level was 2.7%, and the detection limit (3σ) was 0.4 ng l⁻¹. No interference from heavy metals was observed, but ions of Ba²⁺, Sr²⁺ and K⁺ were found to interfere when the concentration ratios of interferent to lead exceeded values of 2000, 20 000 and 200 000, respectively. Quantitative recovery of lead was achieved from sodium, magnesium, aluminum, lanthanum and heavy metal salt solutions. The high selectivity and sensitivity, combined with extremely low blank values, make the proposed technique particularly attractive for the analysis of high-purity reagents, semiconductors and other high-purity materials. Results are presented for the determination of lead in some high-purity reagents.     

Study of the preconcentration and determination of ultratrace rare earth elements in environmental samples with an ion exchange micro-column

A study was carried out on the preconcentration of ultratrace rare earth elements (REEs) in environmental samples with a micro ion-exchange column and determination by inductively coupled plasma mass spectrometry (ICP-MS). The preconcentration parameters were optimized and the REE recovery was ca. 100% in the pH range 4 to 6 with an ionic strength (μ) less than 0.18. The ion-exchange column capacity with respect to REEs was estimated as 0.96 mmol/g. The linear response coefficients ranged from 0.995 to 0.997 at the pg mL^–1 level. The concentration in the blank could be minimized (0.09 to 3.1 pg mL^–1) if the buffer solution and the water were purified. The detection limits ranged from 0.03 to 0.40 pg mL^–1, for a preconcentration factor of 100. The precision and accuracy of the method was evaluated with a synthetic standard solution and real samples. Results indicated that the REE recovery ranged from 88.1% to 100.2%, and the RSD ranged from 2.7% to 6.7%. Satisfactory results were achieved when this method was applied for the determination of REEs in raw water, purified water and tap water, as well as in environmental aquatic samples. Meanwhile, the method is simple and flexible.     

Study of the preconcentration and determination of ultratrace rare earth elements in environmental samples with an ion exchange micro-column

A study was carried out on the preconcentration of ultratrace rare earth elements (REEs) in environmental samples with a micro ion-exchange column and determination by inductively coupled plasma mass spectrometry (ICP-MS). The preconcentration parameters were optimized and the REE recovery was ca. 100% in the pH range 4 to 6 with an ionic strength (μ) less than 0.18. The ion-exchange column capacity with respect to REEs was estimated as 0.96 mmol/g. The linear response coefficients ranged from 0.995 to 0.997 at the pg mL^–1 level. The concentration in the blank could be minimized (0.09 to 3.1 pg mL^–1) if the buffer solution and the water were purified. The detection limits ranged from 0.03 to 0.40 pg mL^–1, for a preconcentration factor of 100. The precision and accuracy of the method was evaluated with a synthetic standard solution and real samples. Results indicated that the REE recovery ranged from 88.1% to 100.2%, and the RSD ranged from 2.7% to 6.7%. Satisfactory results were achieved when this method was applied for the determination of REEs in raw water, purified water and tap water, as well as in environmental aquatic samples. Meanwhile, the method is simple and flexible. Received: 17 January 1997 / Revised: 23 April 1997 / Accepted: 29 April 1997     

Application of factorial design and Doehlert matrix for determination of trace lead in environmental samples by on-line column preconcentration FAAS using silica gel chemically modified with niobium(V) oxide.

In this study a new method for Pb determination in water using solid phase extraction coupled to a flow injection system and flame atomic absorption spectrometry was developed. The sorbent used for Pb preconcentration and extraction was silica gel chemically modified with niobium(V) oxide. Flow and chemical variables of the system were optimized through a multivariate procedure. The factors selected were buffer type, eluent concentration, and sample and eluent flow rates. It was verified that the aforementioned factors as well as their interactions were statistically significant at the 95% confidence level. The effect of foreign ions was evaluated using a fractionary factorial experimental design. The detection limit was 0.35 microg L(-1) and the precision was 1.6%. Results for recovery tests using different environmental samples were between 90 and 104%. Certified reference materials were analyzed in order to check the accuracy of the proposed method.     

Multi-wall carbon nanotubes chemically modified silica microcolumn preconcentration/separation combined with inductively coupled plasma optical emission spectrometry for the determination of trace elements in environmental waters

A novel adsorbent of multi-wall carbon nanotubes (MWCNTs) chemically modified silica (MWCNTs-silica) was synthesised and employed as the adsorbent material for solid-phase extraction (SPE) of trace Zn(II), Cu(II), Cd(II), Cr(III), V(V) and As(V) in environmental water samples followed by inductively coupled plasma optical emission spectrometry detection. This material inherits the advantages of nanomaterial MWCNTs and conventional silica with dual functional groups (–NH₂ and –COOH), and avoid the problem of nanomaterial in SPE, such as high pressure. The factors affecting the separation and preconcentration of target elements such as pH, sample flow rate and volume, eluent concentration and volume were investigated. Under the optimised conditions, the detection limits for Zn(II), Cu(II), Cd(II), Cr(III), V(V) and As(V) were 0.27, 0.11, 0.45, 0.91, 0.55 and 0.67 μg L^?1 with the relative standard deviations of 3.1, 5.9, 4.1, 4.0, 7.3 and 8.6% (c = 10 μg L^?1, n = 7), respectively. The adsorption capacity of MWCNTs-silica was 26.6, 70.0, 13.8, 58.0, 20.0 and 20.0 mg g^?1 for Zn(II), Cu(II), Cd(II), Cr(III), V(V) and As(V), respectively, and the prepared adsorbent could be reused more than 100 times. In order to validate the developed method, two certified reference materials of GSBZ50009-88 and GSBZ 50029-94 environmental waters were analysed and the determined values were in good agreement with the certified values. The developed method has been applied to the determination of trace elements in environmental water samples with satisfactory results.     

Multi-elemental analysis in biological samples by on-line preconcentration on 8-hydroxyquinoline-cellulose microcolumn coupled to simultaneous ICP-AES

Summary The analytical performance of an on-line oxine-cellulose microcolumn preconcentration system coupled to simultaneous ICP was investigated. Different factors including the pH of the sample solution, the flow rates of sample loading and eluation, the acidity of eluent and different eluents were investigated and optimized. In comparison with continuous aspiration, the signal enhancement factors of eleven elements (Zn, Cu, Ni, V, Cr, Fe, Mn, Co, Pb, Cd and Al) were in the range of 6.4 to 13.5 for peak height (0.5 s) and 3.7 to 5.8 for peak area (15 s), respectively. The influences of matrix ions, such as Ca, Mg, Fe, Cu and NaCl were studied. Performance was demonstrated by simultaneous determination of seven (Zn, Cu, Ni, V, Cr, Fe, Mn) elements in a number of CRMs. Most results were satisfactory, except for iron and chromium. The possible reasons were discussed. Co, Pb, Cd and Al were not available in the simultaneous instrument. Therefore, only the analytical performance was measured for these elements by the sequential instrument.On leave from Shanghai Institute of Metallurgy, Academia Sinica, Shanghai, China 200050     

弱酸阳离子交换纤维柱富集-电感耦合等离子体原子发射光谱法测定水样中的稀土

提出了聚丙烯基弱酸性阳离子交换纤维柱富集痕量稀土元素,1.0 mol/L HCl溶液作为洗脱剂,电感耦合等离子体原子发射光谱法测定水样中稀土元素的方法。在优化的试验条件下,弱酸性阳离子交换纤维对La、Nd、Eu、Gd、Er和Yb的吸附容量分别为86.5,98.2,98.7,99.2,84.9,91.5 mg/g;La、...     

Application of ICP-AES to the determination of rare earth elements in phosphate samples

Summary ICP-AES has been used for the determination of rare earth elements (REE) in samples of phosphorite deposits collected from the Western Desert, Egypt. Complete dissolution of the samples was achieved by using acid digestion with HF/HNO₃/HCl in a PTFE closed vessel and subsequent treatment with HClO₄, with the same procedure but with fuming HCl replacing HClO₄ and with HNO₃ and fuming HCl in a quartz vessel and subsequent treatment with HF/HClO₄/HNO₃. Analysis lines for La, Ce, Pr, Nd, Sm, Gd, Dy and Y were selected after study of the spectral interferences for the sample types concerned. Results revealed that the average total content of the REE, which could be directly determined in the present samples, varies between 1.08 and 1.53 mg/g, whereas individual element concentrations range from 40 to 300 g/g. Analysis results obtained with the different dissolution techniques were found to be in good agreement. On leave from the National Research Centre, Physics Department — Spectroscopy Laboratory, Cairo, Egypt     

Spectrophotometric determination of trace uranium in geological samples by flow injection analysis with on-line levextrel resin separation and preconcentration

A flow-injection system with on-line separation and preconcentration is described for the spectrophotometric determination of trace uranium in geological samples. Uranium is selctively adsorbed from 0.7 mol l^?1 nitric acid on a microcolumn (40 mm long, 4.4 mm i.d.) containing levextrel CL-5209 resin (120–200 mesh) and separated from the sample matrix and most of the co-existing ions; 10-fold concentration is obtained. Eluted uranium is determined spectrophotometrically with arsenazo-III. The detection limit is μg l^?1 uranium and calibration is linear up to 0.3 mg l^?1 uranium With dual columns operated alternately for adsorption and elution, 30 samples can be analyzed per hour. Masking agents are added to eliminate interferences from thorium and iron. The method is sensitive and highly selective, easy to operate and suitable for routine analysis of geological samples for uranium.     

An on-line preconcentration/separation system for the determination of bismuth in environmental samples by FAAS

An on-line preconcentration procedure for the determination of bismuth by flame atomic absorption spectrometry (FAAS) has been described. Lewatit TP-207 chelating resin, including iminodiacetate group, packed in a minicolumn was used as adsorbent material. Bi(III) was sorbed on the chelating resin, from which it could be eluted with 3 mol L⁻¹ HNO₃ and then introduced directly to the nebulizer-burner system of FAAS. Best preconcentration conditions were established by testing different resin quantities, acidity of sample, types of eluent, sample and eluent solution volumes, adsorption and elution flow rates, and effect of interfering ions. The detection limit of the method was 2.75 μg L⁻¹ while the relative standard deviation was 3.0% for 0.4 μg mL⁻¹ Bi(III) concentration. The developed method has been applied successfully to the determination of bismuth in pharmaceutical cream, standard reference materials and various natural water samples with satisfactory results.     

Simultaneous determination of rare earth elements by using substoichiometric separation of lanthanium

An analytical method for the simultaneous determination of rare earth elements by using substoichiometry with two chelating agents, a complexon and an extracting agent, is proposed. The principle of the method is that the element which has the lowest stability constant with the complexon is separated substoichiometrically, while other elements which have higher stability constants are separated quantitatively by a single extraction. This method was applied to neutron activation analysis of rare earth elements. Lanthanum, europium and terbium in orchard leaves were determined simultaneously by using substoichiometric separation with DTPA and TTA.     

Flow injection on-line preconcentration with an ion-exchange resin coupled with microwave plasma torch-atomic emission spectrometry for the determination of trace rare earth elements

A sensitive and rapid on-line method has been developed for the determination of trace amounts rare earth elements (REEs), lanthanum, cerium, neodymium and yttrium, by microwave plasma torch-atomic emission spectrometry (MPT-AES) combined with micro-column separation/preconcentration. A strong basic cinnamene anion exchange resin is used for matrix elimination and enrichment of the analytes. The adsorbed metal ions are subsequently eluted from the column and transferred into the detector with nitric acid solution for simultaneous multi-element determination. Various factors influencing the separation/preconcentration, sample flow rate, loading time, acidity and eluent flow rate, concentration, have been studied in detail. Under the optimized conditions, the detection limits for lanthanum, cerium, neodymium and yttrium based on three times of standard deviations of blank by 7 replicates are 0.89, 2.02, 1.56 and 0.78 μg·L^− 1, and the relative standard deviations are determined as 1.54, 4.29, 4.95 and 3.90%, respectively. The proposed method has been applied to the analysis of the four REEs in high purity Sm₂O₃, Eu₂O₃, Gd₂O₃, Tb₂O₃, Dy₂O₃, Yb₂O₃, and Lu₂O₃ samples with a recovery range of 95.1-104.8%.     

Preconcentration of rare earth elements on silica gel loaded with 1-phenyl-3-methyl-4-benzoylpyrazol-5-one prior to their determination by ICP-AES.

A new chelating resin, silica gel loaded with 1-phenyl-3-methyl-4-benzoylpyrazol-5-one (PMBP), was prepared and used for the preconcentration of trace amounts of rare earth elements (REEs) in water samples prior to their determination by inductively coupled plasma atomic emission spectrometry (ICP-AES). REEs (La, Eu, Yb and Y) were quantitatively retained on the column packed with modified silica gel in the pH range 5 - 8 and separated from the matrix, and then recovered by eluting with 2.0 mol L(-1) HNO3. The adsorption capacity of modified silica gel for La, Eu, Yb and Y was 0.208, 0.249, 0.239 and 0.224 mmol g(-1), respectively. The method has been successfully applied for the determination of La, Eu, Yb and Y in geological and environmental samples with satisfactory results.     

Interference-free determination of trace levels of gold and palladium in geological and metallurgical samples by flame atomic absorption spectrometry coupled with a flow injection on-line microcolumn preconcentration and separation system

A simple and highly selective method was developed for the routine determination of trace or ultratrace amounts of gold and palladium in geological and metallurgical samples. The method uses flow injection on-line preconcentration and separation with determination by flame atomic absorption spectrometry. Au and Pd in the sample are adsorbed on a 2-mercaptopyrimidine chemically modified silica gel (MPMSG) packed microcolumn in a 0.50M HCl medium and then eluted with 0.5 or 1.0% thiourea solution. The eluates are introduced into the flame atomic absorption spectrometer directly. With the use of a 0.85 mL microcolumn (about 0.14 g MPMSG packed), the present system tolerated concentrations of common base metal ions up to 25.0 mg/mL and concentrations of anions up to 100.0 mg/mL when Au(III) at 0.100 microg/mL and Pd(II) at 0.200 microg/mL were preconcentrated for 60 s with a sample flow rate of 5.0 mL/min. The limits of detection were 3.1 ng/mL for Au(III) and 6.1 ng/mL for Pd(II) with relative standard deviations of < or = 2.5%. The analytical results obtained by the proposed method for geological and metallurgical samples were in good agreement with the certified values.     

Automated on-line separation preconcentration system for palladium determination by graphite furnace atomic absorption spectrometry and its application to palladium determination in environmental and food samples

A flow injection (FI) system was used to develop an efficient on-line sorbent extraction preconcentration system for palladium by graphite furnace atomic absorption spectrometry (GFAAS). The investigated metal was preconcentrated on a microcolumn packed with 1,5-bis(di-2-pyridyl)methylene thiocarbohydrazide immobilized on silica gel (DPTH-gel). The palladium is eluted with 40 μl of HCl 4 M and directly introduced into the graphite furnace. The detection limit for palladium under the optimum conditions was 0.4 ng ml⁻¹. This procedure was employed to determine palladium in different samples.     

Determination of trace amounts of rare earth and other elements in rice samples by ICP-AES with sample introduction by tungsten-coil electrothermal vaporization

Summary A device with tungsten-coil electrothermal vaporization for sample introduction into ICP has been proposed. It was applied to the determination of trace amounts of rare earth and other elements in rice samples. Several influencing factors were investigated in detail, such as drying and vaporization parameters, carrier gas flow rate, volume of vaporization chamber and matrix effects. Under optimal experimental conditions, the detection limits for Mg, Cu, Mn, Cr, Fe, Co, Ni and eight rare earth elements are of the order of 10⁻⁹−10⁻¹¹ g. The detection limits for the rare earth elements tested by the present method are comparable to and, in most instances, exceed those for the GFAAS and conventional pneumatic nebulisation-ICP-AES. A precision with RSD<6% was obtained.     

Dithizone immobilized silica gel on-line preconcentration of trace copper with detection by flame atomic absorption spectrometry

A novel adsorbent-silica gel bound dithizone (H₂Dz-SG) was prepared and used as solid-phase extraction of copper from complex matrix. The H₂Dz-SG is investigated by means of FT-IR spectra and the SEM images, demonstrating the bonding of dithizone. The H₂Dz-SG quantitatively adsorb copper ions, and the retained copper is afterwards collected by elution of 10% (v/v) nitric acid. An on-line flow injection solid-phase extraction procedure was developed for trace copper separation and preconcentration with detection by flame atomic spectrometry. By loading 5.4 mL of sample solution, a liner range of 0.5-120 μg L⁻¹, an enrichment factor of 42.6, a detection limit of 0.2 μg L⁻¹ and a precision of 1.7% RSD at the 40 μg L⁻¹ level (n = 11) were obtained, along with a sampling frequency of 47 h⁻¹. The dynamic sorption capacity of H₂Dz-SG to Cu²⁺ was 0.76 mg g⁻¹. The accuracy of the proposed procedure was evaluated by determination of copper in reference water sample. The potential applications of the procedure for extraction of trace copper were successfully accomplished in water samples (tap, rain, snow, sea and river). The spiking recoveries within 91-107% are achieved.     

Rapid coprecipitation technique using yttrium hydroxide for the preconcentration and separation of trace elements in saline water prior to their ICP-AES determination.

Yttrium hydroxide quantitatively coprecipitated Be(II), Ti(IV), Cr(III), Mn(II), Fe(III), Co(II), Ni(II), Cu(II), Zn(II), Cd(II), and Pb(II) at pH 9.6 - 10.0 for seawater and pH 10.5 - 11.4 for a table-salt solution. The coprecipitated elements could be determined by inductively coupled plasma atomic emission spectrometry; yttrium was used as an internal standard element. The detection limits ranged from 0.001(6) microg (Mn(II)) to 0.22 microg (Zn(II)) in 100 mL of sample solutions. The operation time required to separate 11 elements was approximately 30 min.