活性炭的改性研究及对四环素的吸附

研究了改性对活性炭的物理化学性质及其对四环素吸附性能的影响。结果发现,硝酸氧化改性可增加活性炭表面的酸性基团,提高比表面亲水性,降低pHPZC值,同时也改变了活性炭的表面微观形貌。低温、低浓度硝酸氧化改性,增加了活性炭的比表面积,对四环素的吸附以物理吸附为主。高温氧化改性使得比表面积降低,酸性基团增加,且吸附容量与活性炭比表面积、表面总酸度呈一定的线性关系。     

改性活性炭对噻吩的吸附性能研究

用过硫酸铵、臭氧对椰壳活性炭和煤基活性炭进行氧化改性,研究了改性活性炭对噻吩的吸附性能,材料结构袁征结果表明,经两种方法氧化处理后,椰壳炭的孔结构基本保持不变,而煤基炭的比表面积和孔容有所增加.Boehm滴定发现氧化后活性炭表面含氧官能团数量增加并由FT-TR图谱得到证实.氧化处理提高了噻吩在活性炭表面的吸附容量与Langmuir和Freundlich两种吸附等温线方程的相关性.采用拟一级、拟二级和粒子内扩散模型速率方程来考察吸附动力学,并计算了这些动力学模型的速率常数,拟二级模型和实验数据之间有较好的相关性.同时对影响吸附性能的因素进行了分析.     

活性炭的表面处理对二苯并噻吩催化氧化脱除的影响

将一种木质活性炭经过三种表面处理,即高锰酸钾稀硫酸溶液液相氧化、浓硝酸液相氧化和350℃低温气相氧化处理。实验所选活性炭及相应的表面改性炭使用氮气吸附和Boehm滴定分别进行了结构性质和表面化学表征。研究了所选活性炭和相应的表面改性炭催化过氧化氢氧化脱除二苯并噻吩（DBT）。实验结果表明,活性炭表面化学对二苯并噻吩的氧化脱除影响很大;炭表面化学对DBT吸附脱除的影响不同于对DBT氧化脱除的影响,表面酸性越强越有利于DBT的吸附;表面羰基能加速过氧化氢产生自由基,表面羰基量的增加明显有利于DBT的氧化脱除。活性炭经过热处理后,在二苯并噻吩的氧化脱除中催化活性明显增加,正辛烷溶液中硫的体积质量从0.556g·L-1降到0.009g·L-1。     

活性炭电极材料的表面改性和性能

以硝酸、双氧水、氨水三种化学试剂分别对活性炭进行表面改性, 用N2吸附法和FTIR表征炭材料改性前后孔结构和表面官能团的变化. 制备了以改性活性炭为电极材料, KOH溶液为电解质的模拟双电层电容器. 用恒流充放电、循环伏安、交流阻抗等方法考察了双电层电容器的电化学性能. 结果表明, 改性活性炭比表面积和平均孔径有所降低, 并且在炭材料表面引入了含氧或含氮官能团, 如—OH、>CO、—NH2等, 使炭材料的润湿性增强、电阻减小、电化学性能显著提高. 用65%硝酸改性后炭材料的比容量最高达到250 F·g-1, 比原样炭提高了72.4%; 实验电容器的漏电流急剧下降, 只有3-18 μA, 为原来电容器的漏电流(371 μA)的0.8%-4.9%.     

硝酸改性活性炭上氧/氮官能团对脱汞性能的促进作用

采用硝酸氧化手段对活性炭进行了表面处理, 并在固定床反应器上测试了其脱除单质汞的性能. 研究表明, 在模拟烟气中硝酸改性活性炭能有效脱除单质汞. 采用元素分析、Brunauer-Emmett-Teller (BET)比表面积、扫描电子显微镜(SEM)、拉曼(Raman)光谱、Boehm滴定、程序升温脱附(TPD)和X射线光电子能谱(XPS)等手段研究了活性炭表面官能团对其脱汞性能的影响. 结果表明: 硝酸氧化处理能同时增加活性炭表面含氧官能团和含氮官能团的含量. 与改性活性炭的物理性质相比, 其化学性质对脱汞性能的影响更大, 单质汞主要被改性活性炭氧化为HgO而去除. 在脱汞反应中, 羰基、酯基和酸酐等含氧官能团可能是活性吸附位点, 反应后这些官能团被还原为羟基或者醚基; 而吡咯等含氮官能团可能是活性催化位点. 此外, 基于上述表征结果提出了硝酸改性活性炭表面官能团的脱汞机制.     

活性炭纤维对铂离子的还原吸附特征

利用不同的活化工艺,制备了水蒸汽活化和磷酸或氯化锌活化活性炭纤维,并借助扫描电镜(SEM)、X-射线衍射(XRD)和光电子能谱(XPS)等技术,研究了这些活性炭纤维对铂的还原吸附特征。结果表明,各活性炭纤维均能还原吸附铂离子,吸附容量为30mgPt/gC至90mgPt/gC之间。依据活性炭纤维种类的不同,还原吸附的铂呈粒状或放射性簇状存在于活性炭纤维表面,铂颗粒的粒径为几十nm至1μm之间。对纤维表面铂的XRD分析表明,还原吸附的铂呈无定型结构,但经过400℃高温处理后,颗粒转化为金属铂结晶形态。还原吸附铂后,活性炭纤维表面的含氧基团相应增加,显示其表面被氧化为羟基和羰基。     

石油焦系活性炭的吸附脱硫

选取独山子石油焦为原料，以物理活化法制得比表面积达500m2/g～900m2/g的活性炭，进行吸附脱硫研究。采用酸氧化法对活性炭孔结构和微观孔径分布进行改性。酸氧化使活性炭表面酸性官能团含量明显增加，增加量约为原来的5倍。活性炭吸附脱硫性能随表面酸性官能团含量的增加而增大。理想的酸化条件是浓硝酸120℃氧化40min。通过静态吸附实验，活性炭吸附脱硫的最佳条件是，温度25℃，压力1.0MPa，静态吸附6h。最佳条件下吸附脱硫可使模型化合物硫的质量分数从137.9×10－6降至3.1×10－6。从活性炭孔径匹配考察可知，平均孔直径在0.8nm～2.1nm的活性炭对模型化合物硫的质量分数降低具有明显效果。     

硝基苯在纳米炭黑上的吸附特征

利用炭黑作吸附剂,考察吸附质流速和硝酸处理浓度对炭黑吸附有机废水中硝基苯的影响,确定了最佳吸附处理条件,比较了不同炭素材料的吸附性能。实验结果表明:与炭管、椰壳活性炭和颗粒活性炭3种炭素材料相比,炭黑对硝基苯具有更佳的吸附性能。XRD、BET表征结果表明炭黑表面存在大约40nm介孔结构,毛细凝聚在吸附中起到了重要作用。     

不同活性炭上Pt催化剂的分散性及其在甲基环己烷脱氢反应中的催化性能

在不同方法处理的活性炭上采用传统浸渍方法制备了负载Pt催化剂,并考察了其在甲基环己烷脱氢反应中的催化性能.对炭载体的氮吸附和程序升温脱附的表征结果表明,活性炭经过硝酸氧化处理和氢气高温处理后,活性炭的孔结构基本不变,但表面含氧官能团的数量和种类发生了变化.这些不同的表面基团直接影响了Pt粒子在载体上的分散度,进而使催化剂在反应中表现出不同的活性.     

硝酸氧化对三种活性炭结构及化学性能的影响

对煤质活性炭、椰壳活性炭和沥青基活性炭进行了硝酸氧化处理。通过酸碱滴定、红外光谱、比表面积和孔径分布测定研究了硝酸氧化对3种活性炭的表面官能团、比表面积和孔结构的影响,以及硝酸氧化对活性炭进一步进行乙二胺胺化的影响。结果表明,在所选的3种活性炭中,氧化对于椰壳活性炭的物理结构破坏最严重,比表面积下降了16%,而煤质活性炭与沥青基活性炭均很好地保持了原有的结构性质。硝酸氧化在不同的活性炭表面均引入了一定量的酸性基团,其中沥青基活性炭氧化后表面酸性基团含量最高,达到2.36mmol/g。氧化后的3种活性炭接枝乙二胺后,沥青基活性炭的表面碱性基团含量最高,达到1.39mmol/g。     

PREPARATION OF ACTIVATED CARBON FIBER AND THEIR XENON ADSORPTION PROPERTIES（Ⅲ）-ADSORPTION ON MODIFIED ACTIVATED CARBON FIBER

Structures of a series of activated carbon fibers were modified by impregnating them withorganic and inorganic materials such as Methylene blue(Mb)、 p-nitrophenol (PNP)、 NaCl or byoxidizing with KMnO4 or HNO3. The influence of pore filling or chemical treatment on their xenonadsorption properties was studied. The experimental results show that Mb and PNP filling ofactivated carbon fibers result in the decrease of xenon adsorption capacities of these treated ACFs,which is due to the decrease of their surface area and micro-pore volume. However, the adsorptioncapacity increases greatly with oxidizing treatment of activated carbon fibers by 7mol/L HNO3.     

PREPARATION OF ACTIVATED CARBON FIBER AND THEIR XENON ADSORPTION PROPERTIES (II)-XENON ADSORPTION PROPERTIES

1. INTRODUCTION The adsorption and concentration of xenon has practical application interest in the purification of radioactive waste gas released from nuclear plant operation. Moreover, the monitor of xenon isotopic, derived from nuclear explosion or nu…     

PREPARATION OF ACTIVATED CARBON FIBER AND THEIR XENON ADSORPTION PROPERTIES（Ⅱ）-XENON ADSORPTION PROPERTIES

The adsorption of xenon from air has an interest in the monitoring of nuclear explosion oraccident, or in the treatment of nuclear waste gas. In this paper, the pore structure of several series ofactivated carbon fibers has been characterized. The adsorption properties of xenon on theseactivated carbon fibers under different temperatures have been studied in details. The results showthat the xenon adsorption amount on activated carbon fibers do not increase with specific surfacearea of adsorbents, but are closely related to their pore size distribution. Pores whose radius equal toor narrow than 0.4nm would be more advantageous to the adsorption of xenon.     

正交实验研究硝酸改性对活性焦表面性质及脱硫性能的影响

用硝酸对活性焦进行改性,采用正交实验法,考察了硝酸浓度、活化温度、活化时间以及煅烧温度对活性焦脱硫性质的影响,并在固定床反应装置上进行了活性焦评价实验。利用酸碱滴定、碘值测定、N₂吸附法、傅里叶红外光谱分析等对改性活性焦的表面酸碱性、比表面积、孔容等进行了分析和表征。实验结果表明,硝酸改性增加了活性焦的比表面积,提高了活性焦表面碱性;煅烧有助于提高表面碱性;硝酸改性明显提高了活性焦的脱硫性能。     

几种植物基活性炭材料的表面结构与吸附性能比较——(II)表面化学结构与吸附性能研究

用X-射线光电子能谱对3种植物基活性炭材料:椰壳活性炭 (CAC4)、剑麻茎基活性炭(SSAC)和剑麻基活性碳纤维 (SACF) 的表面化学结构进行了表征,并研究和对比了它们的吸附性能,包括对碘、苯酚和亚甲基蓝的液相吸附性能,对有机蒸汽的吸附性能以及对Au3+的还原吸附性能等。结果表明,3个样品表面均含有多种含氧官能团,吸附能力SACF>SSAC> CAC4。样品的吸附性能主要取决于自身孔结构,与其表面化学结构也有密切的关系。     

Structural Characterization and Property Study on the Activated Alumina-activated Carbon Composite Material

AlCl3,NH3·H2O,HNO3 and activated carbon were used as raw materials to prepare one new type of activated alumina-activated carbon composite material.The influence of heat treatment conditions on the structure and property of this material was discussed;The microstructures of the composite material were characterized by XRD,SEM,BET techniques;and its formaldehyde adsorption characteristic was also tested.The results showed that the optimal heat treatment temperature of the activated alumina-activated carbon composite material was 450 ℃,iodine adsorption value was 441.40 mg/g,compressive strength was 44 N,specific surface area was 360.07 m2/g,average pore size was 2.91 nm,and pore volume was 0.26 m3/g.According to the BET pore size distribution diagram,the composite material has dual-pore size distribution structure,the micro-pore distributes in the range of 0.6-1.7 nm,and the meso-pore in the range of 3.0-8.0 nm.The formaldehyde adsorption effect of the activated alumina-activated carbon composite material was excellent,much better than that of the pure activated carbon or activated alumina,and its saturated adsorption capacity was 284.19 mg/g.     

Carbon molecular sieves for air separation from Nomex aramid fibers

Activated carbon fibers prepared from aramid fibers have proved to possess outstanding homogeneity in pore size, most of all when Nomex aramid fiber is used as precursor. Taking advantage of this feature, microporous carbon molecular sieves for air separation have been prepared through carbon vapor deposition of benzene on Nomex-derived carbon fibers activated to two different burnoff degrees. Carbon molecular sieves with good selectivity for this separation and showing acceptable adsorption capacities were obtained from ACFs activated to the two burnoff degrees chosen.     

苯基键合高比表面积活性炭的制备及其对挥发性有机化合物的吸附性能研究

以核桃壳为原料,经过碳化、KOH活化, 制备了高比表面积活性炭,通过三甲基氧基苯基硅烷对活性炭表面进行改性,制得苯基键合高比表面积活性炭吸附材料.通过氮气吸附法测定了苯基键合活性炭的比表面积及孔径分布;采用红外光谱、X射线光电子能谱、X射线粉末衍射技术对苯基键合活性炭的有机官能团、表面元素的化学环境及晶体结构进行了表征.将该吸附材料制成采样管,吸附空气中的挥发性有机物,二硫化碳解吸后使用气相色谱进行分析.考察了苯基键合活性炭对乙醇、丙酮、正己烷、乙酸乙酯、四氢呋喃、1,2-二氯乙烷和苯共7种挥发性有机化合物(VOCs)的吸附性能,饱和吸附量在129~216 mg/g之间;在0.05~ 2.50 mg/mL范围内,7种组分的峰高与浓度呈良好的线性关系,检出限在0.92~3.60 mg/m3之间.     

活性炭纤维吸附脱除NO过程中NO氧化路径分析

在小型固定床吸附实验台上开展了黏胶基活性炭纤维吸附脱除NO的实验研究。采用H₂O₂溶液浸渍以及热处理方法对活性炭纤维表面进行修饰,以获得表面孔隙结构接近而含氧官能团含量不同的样品;考察样品在惰性氮气气氛、含氧气氛下吸附脱除NO的效果,以及表面含氧含氮官能团的变化规律。探讨了含氧官能团在NO催化氧化过程中的作用及含氧气氛下O₂对于NO转化为NO₂的影响,分析了活性炭纤维表面吸附的NO向NO₂的主要转化途径。结果表明,在氮气气氛下活性炭纤维表面C-O官能团对吸附态的NO起到氧化作用,吸附态NO被C-O官能团氧化生成-NO₂官能团;在含氧气氛下活性炭纤维吸附NO后表面出现-NO₂、-NO₃官能团,通过长时间实验测定三种样品在含氧气氛下对NO吸附的效果,发现三种样品稳定时催化氧化效果一致,表明含氧官能团对初始NO的物理吸附影响较大,而对整个吸附过程影响较小。吸附在活性炭纤维表面上的NO与环境气氛中的游离态O₂发生氧化反应是NO转变为NO₂的主要途径。     

Liquid-phase adsorption: Characterization and use of activated carbon prepared from diosgenin production residue

The adsorption behavior of activated carbon (AC) prepared from the residue of diosgenin by-product was characterized. The adsorption capacities of AC such as iodine, phenol and methylene blue (MB) are 933.28, 145.38 and 165 mg/g, respectively. The results of MP analysis and BJH method show AC has developed micropore and mesopore volumes, which are 0.1621 and 0.2623 cm³/g respectively, with the mean pore diameter of 1.49 nm. Comparison of the liquid phase adsorption capacities of AC to the standard activated carbon (SAC) and the commercial activated carbon (CAC) for wastewater treatment showed AC was superior to SAC and CAC. Experiments on phenol and MB adsorption and COD and chroma removal from diosgenin wastewater were carried out under different conditions of contact time, temperature, concentration, adsorbent dose and pH. The removal of COD and chroma of 10-multiple wastewater is 92.46 mg/g and 88 %, respectively. Adsorption parameters for the Langmuir and Freundlich isotherm models were determined. At lower temperatures, the data for phenol and COD fitted Freundlich model better than Langmuir model and vise versa for MB and chroma. Adsorption followed second-order kinetics. The study proves that AC prepared from the residue of diosgenin by-product can be used as adsorbent for the treatment of diosogenin wastewater as a cost-effective approach of resource recycle of Discorea zingiberensis C.H. Wright.