Analytical application of 2f-wavelength modulation for isotope selective diode laser graphite furnace atomic absorption spectroscopy

Experiences in the analytical application of the 2f-wavelength modulation technique for isotope selective atomic absorption spectroscopy in a graphite furnace are reported. Experimental as well as calculated results are presented, mainly for the natural lithium isotopes. Sensitivity, linearity, and (isotope) selectivity are studied by intensity modulation and wavelength modulation. High selectivities can be attained, however, on the cost of detection power. It is shown that the method enables the measurement of lithium isotope ratios larger than 2000 by absorption in a low-pressure graphite tube atomizer.     

Isotope selective element analysis by diode laser atomic absorption spectrometry

The analytical figures of merit of isotope selective diode laser atomic absorption spectrometry (DLAAS) in low-pressure graphite furnaces are given for lithium and rubidium. While⁶Li and⁷Li were measured by Doppler-limited as well as by Doppler-free absorption spectroscopy of the 670.79 nm resonance line, Doppler-free saturation spectroscopy was applied for analysis of the⁸⁵Rb and⁸⁷Rb D2 resonance line at 780.03 nm. Three different modulation techniques were applied and compared: (i) intensity modulation, (ii) wavelength modulation, and (iii) a combination of intensity and wavelength modulation.     

Application of the 2f-wavelength modulation technique for the measurement of large lithium isotope ratios by diode laser graphite furnace atomic absorption spectroscopy

The measurement of large lithium isotope ratios by diode laser graphite furnace atomic absorption spectroscopy was investigated using a low pressure atomizer and 2f-wavelength modulation (WM) detection. The measurements were supported by computer simulations. Compared with a direct absorption measurement, the relative absorption sensitivity for ⁶Li is considerably reduced when 2f-WM is performed in the center of the ⁶Li D1 fine structure component, but it will be enhanced, when the center of modulation is tuned to the maximum in the red wing of the 2f-WM line profile. The results of calculated 2f-WM line strengths were used to deconvolute overlapping lines and enabled the measurement of ⁷Li/⁶Li isotope ratios as large as approximately 2000. The Li content of a sample with a strong sodium chloride matrix was determined by isotope dilution.     

Effect of mild oxidation of natural graphite (NG7) on anode-electrolyte thermal reactions

The effect of mild oxidation of natural graphite (NG7) and some other parameters on the reaction between a fully lithiated graphite anode (Li _x C₆, x=1.0–1.1) and 1 M lithium hexafluoroarsenate in ethylene carbonate and diethyl carbonate electrolyte (1:2, v/v) were studied by differential scanning calorimetry (DSC). It was found that mild oxidation of the graphite suppressed the exothermic reaction of the fully lithiated anode with the electrolyte, most probably as a result of the formation of a more stable and chemically bonded solid electrolyte interphase. Separation and removal of the small graphite particles from the anode mixture suppressed this reaction further. It was also found that the copper current collector, the amount of electrolyte and binder as well as other parameters have a significant influence on the heat evolution as measured by DSC. Received: 11 October 1999 / Accepted: 1 March 2000     

Separation and preconcentration of Se(IV)/Se(VI) speciation on algae and determination by graphite furnace atomic absorption spectrometry in sediment and water

A novel method for the separation and preconcentration of Se(IV)/ Se(VI) with algae and determination by graphite furnace atomic absorption spectrometry (GFAAS) has been developed. The Se(VI) is extracted with algae from the solution containing Se(IV)/Se(VI) at pH 5.0, and the remaining Se(IV) is then preconcentrated pH 1.0. The detection limits (3σ, n = 11) of 0.16 μg L^–1 for Se(IV) and 0.14 μg L^–1 for Se(VI) are obtained using 40 mL of solution. At the 2.0 μg L^–1 level the relative standard deviation is 2.6% for Se(IV) and 2.3% for Se(VI). The method has been applied to the determination of Se(IV)/Se(VI) in sediment and water samples. Analytical recoveries of Se(IV) and Se(VI) added to samples are ?97 ± 5% and 102 ± 6% (95% confidence), respectively. Received: 10 February 1999 / Revised: 21 June 1999 / /Accepted: 22 June 1999     

Direct determination of selenoproteins in polyvinylidene difluoride membranes by electrothermal atomic absorption spectrometry

A method for the direct determination of selenoproteins in plastic membranes after protein separation by gel electrophoresis was developed. Quantification was based on the determination of the selenium content of the proteins by electrothermal atomic absorption spectrometry (ET-AAS) after manual introduction of membrane pieces into the graphite furnace. The proteins were separated by sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE) and subsequently transferred to a polyvinylidene difluoride (PVDF) membrane by semi-dry electroblotting. After staining the membrane, the protein bands were excised and chemical modifier was added on top of the excised membrane prior to atomic absorption measurement. Acceptable linearity was achieved in the range 2– 10 ng Se, corresponding to selenium concentrations close to 1 mg/L, when aqueous solutions of selenomethionine standard as well as selenoprotein standard were applied to the membrane. A characteristic mass of 54 ± 4 pg/0.0044 s was obtained for the selenoprotein standard. Protein transfer from polyacrylamide gel to the membrane was quantitative and no interferences were introduced. The method was used for identification of selenoprotein P after enrichment of the protein from human plasma. Received: 28 June 1999 / Revised: 14 September 1999 / Accepted: 16 September 1999     

Direct analysis of solid samples by GFAAS – determination of trace heavy metals in barytes

Solid sampling graphite furnace atomic absorption spectroscopy (SS-GFAAS) has been used for the determination of traces of heavy metals (Cd, Pb, Cu, Cr, Ni, V and As) in barytes over a wide concentration range, e.g. Cd from 0.023 to 27.0 μg/g and Pb from 1.54 to 3509 μg/g.The necessity of determining heavy metals in commercial barytes (naturally occurring barium sulfate), a mineral important to the oil industry because of its use in drilling muds, is discussed. The problems presented by the analysis of this difficult matrix are elegantly solved by using SS-GFAAS for the direct determination of heavy metals. A high-performance graphite furnace AAS with D₂-background correction system and a transversely heated graphite atomizer was used for the investigations. The spectrometer was combined with a mechanical sampling module and an ultramicrobalance. The transfer of solid samples (sample weights 0.031–0.686 mg) into the atomizer was carried out by using an optimized graphite platform as the sample carrier. Calibration curve techniques and standard addition methods were employed using external standards (CRMs). Problems associated with signal deformations like multiple peaks, tailing or shoulders are also discussed and possibilities to solve the problems are given. The influence of the homogeneity of solid samples on the precision and accuracy are shown in a real example. The results obtained by SS-GFAAS were compared with results by other methods like X-ray fluorescence spectroscopy (XRF) and flame AAS after aqua regia microwave extraction. This study has demonstrated that SS-GFAAS is a very powerful and easy-to-use method for quick and accurate analysis of barytes. Received: 9 November 1998 / Revised: 29 January 1999 / Accepted: 2 February 1999     

Direct analysis of solid samples by GFAAS – determination of trace heavy metals in barytes

Solid sampling graphite furnace atomic absorption spectroscopy (SS-GFAAS) has been used for the determination of traces of heavy metals (Cd, Pb, Cu, Cr, Ni, V and As) in barytes over a wide concentration range, e.g. Cd from 0.023 to 27.0 μg/g and Pb from 1.54 to 3509 μg/g.The necessity of determining heavy metals in commercial barytes (naturally occurring barium sulfate), a mineral important to the oil industry because of its use in drilling muds, is discussed. The problems presented by the analysis of this difficult matrix are elegantly solved by using SS-GFAAS for the direct determination of heavy metals. A high-performance graphite furnace AAS with D₂-background correction system and a transversely heated graphite atomizer was used for the investigations. The spectrometer was combined with a mechanical sampling module and an ultramicrobalance. The transfer of solid samples (sample weights 0.031–0.686 mg) into the atomizer was carried out by using an optimized graphite platform as the sample carrier. Calibration curve techniques and standard addition methods were employed using external standards (CRMs). Problems associated with signal deformations like multiple peaks, tailing or shoulders are also discussed and possibilities to solve the problems are given. The influence of the homogeneity of solid samples on the precision and accuracy are shown in a real example. The results obtained by SS-GFAAS were compared with results by other methods like X-ray fluorescence spectroscopy (XRF) and flame AAS after aqua regia microwave extraction. This study has demonstrated that SS-GFAAS is a very powerful and easy-to-use method for quick and accurate analysis of barytes. Received: 9 November 1998 / Revised: 29 January 1999 / Accepted: 2 February 1999     

Anode materials for lithium ion batteries obtained by mild and uniformly controlled oxidation of natural graphite

Modification of natural graphite for anode materials has been a recent focus of research and development. Here we report that a common natural graphite, whose electrochemical performance is very poor, can be modified by solutions of (NH₄)₂S₂O₈, concentrated nitric acid solution, or green chemical solutions such as aqueous solutions of hydrogen peroxide and ceric sulfate. All treatments result in marked improvement of the electrochemical performance, including reversible capacity, coulombic efficiency in the first cycle, and cycling behavior. The main reason is the effective removal of active defects in natural graphite, formation of a new dense surface film consisting of oxides, improvement of the graphite stability, and introduction of more nanochannels/micropores. As a result, these changes inhibit the decomposition of electrolytes, prevent the movement of graphene planes along the a-axis direction, and provide more passages and storage sites for lithium. They are mild and the uniformity of the product can be well controlled. Pilot experiments show economic promise for their application in industry to manufacture anode materials for lithium ion batteries.Presented at the 3rd International Meeting on Advanced Batteries and Accumulators, 16–20 June 2002, Brno, Czech Republic     

Study of chemical modifiers for the determination of chromium in biological materials by tungsten coil electrothermal atomic absorption spectrometry

The determination of Cr in digest solutions of mussels and non-fat milk powder by tungsten coil electrothermal atomic absorption spectrophotometry (TC-ETAAS) is affected by interferences. This study reports a critical evaluation of chemical modifiers that could be employed to correct these interferences. The chemical modifiers tested were: Mg [as Mg(NO₃)₂], Pd [as Pd(NO₃)₂], NH₄NO₃, ascorbic acid, and mixtures of these compounds. The less effective modifier was NH₄NO₃. The best effects, considering thermal stabilization and sensitivity, were obtained in mixtures of ascorbic acid plus Mg. Chromium was determined by TC-ETAAS in certified reference materials of mussels and non-fat milk powder, and results were comparable with those obtained by graphite furnace atomic absorption spectrophotometry (GFAAS). Received: 19 June 1998 / Revised: 11 January 1999 / Accepted: 16 January 1999     

The lithium intercalation into graphite from electrolyte and from solid lithium

The values of diffusion coefficient (D) of lithium in thermoexpanded graphite during cathodic intercalation from aprotic electrolyte, and upon direct contact with lithium metal, are measured. In the first case galvanostatic switch-on curves were registered, in the second case the method of x-ray diffraction was used. In the both cases D was close to 10^-10 cm²/s.Presented at the 3rd International Meeting "Advanced Batteries and Accumulators," June 16th–20th 2002, Brno, Czech Republic     

X-ray spectroscopy study of lithiated graphite obtained by thermal deposition of lithium

X-ray photoelectron spectroscopy (XPS), X-ray emission spectroscopy (XES), and near edge X-ray absorption fine structure (NEXAFS) spectroscopy are used for in situ studies of the electronic structure of lithiated natural graphite produced by thermal deposition of lithium upon graphite in a vacuum. By XPS and NEXAFS spectroscopy it is found that lithium vapor thermal deposition results in the formation of a lithiated graphite surface layer and a change in its electronic structure. Based on the quantum chemical simulation of the experimental СK_α XES spectrum of lithiated graphite, it is found that lithium atoms are located mostly on the edges of graphite crystallites. Atomic force microscopy reveals that the size of natural graphite flakes varies from 50 nm to 200 nm.     

The use of S,S-dialkyl dithiocarbonates in Li ion battery electrolytes

S,S-dialkyl dithiocarbonates such as S,S-dimethyl dithiocarbonate and S,S-diethyl dithiocarbonate were tested as solvents for rechargeable lithium ion batteries. Graphite electrodes can be successfully cycled at high reversible capacities in an S,S-dimethyl dithiocarbonate solution containing 1 M LiAsF₆, while lithium ions cannot intercalate into graphite in S,S-diethyl dithiocarbonate solutions. Fourier transform infrared spectroscopy, cyclic voltammetry and chronopotentiometric methods were used in order to monitor the reaction mechanism. Received: 23 April 1997 / Accepted: 5 June 1997     

Suppression of lithium deposition at sub-zero temperatures on graphite by surface modification

Lithium deposition on graphite anodes is considered as a main reason for failures and safety for lithium ion batteries (LIB). Different amounts of carbon coating on the surface of natural graphite are used in this work to suppress the amount of lithium deposited at − 10 °C. Pulse polarization experiments reveal relative polarization of graphite anodes at various temperatures and show that lithium deposition is accelerated at lowered temperatures. Electrochemical experiments, along with photographs, scanning electron microscopy (SEM) images and ex-situ X-ray diffraction (XRD) data suggest that carbon coating not only suppresses the lithium deposition but also enhances the formation of LiC₆ at − 10 °C. The homogeneous potential profile on the graphite surface attained by the carbon coating explains such an improved low temperature performance, as it allows efficient Solid Electrolyte Interface (SEI) film formation, which is a prerequisite for safety LIB.     

Irreversible capacity elimination via immediate contact of carbon with lithium metal

A new method for elimination of irreversible capacity during lithium intercalation into graphite is described. The method consists of bringing the graphite electrode into tight contact with lithium metal in an electrolyte. As a result of such shorting, a passive film is formed at the graphite surface. The dynamics of the film formation and its properties depend on the correlation between the masses of lithium and graphite. The method does not result in a decrease of the reversible capacity.Presented at the 3rd International Conference on Advanced Batteries and Accumulators, 16–20 June 2002, Brno, Czech Republic     

Isotope effect of hydrogen and lithium hydride molecules. Application of the dynamic extended molecular orbital method and energy component analysis

In order to explore the isotope effect including the nuclear–electronic coupling and nuclear quantum effects under the one-particle approximation, we apply the dynamic extended molecular orbital (DEMO) method and energy component analysis to the hydrogen and lithium hydride isotope molecules. Since the DEMO method determines both electronic and nuclear wave functions simultaneously by variationally optimizing all parameters embedded in the basis sets, the virial theorem is completely satisfied and guarantees the relation of the kinetic and potential energies. We confirm the isotope effect on internuclear distances, nuclear and electronic wave functions, dipole moment, the polarizability, and each energy component. In the case of isotopic species of the hydrogen molecule, the total energy decreases from the H₂ to the T₂ molecule due to the stabilization of the nuclear–electronic potential component, as well as the nuclear kinetic one. In the case of the lithium hydride molecule, the energy lowering by replacing ⁶Li with ⁷Li is calculated to be greater than that by replacing H with D. This is mainly caused by the small destabilization of electron–electron and nuclear–nuclear repulsion in ⁷LiH compared to ⁶LiH, while the change in the repulsive components from ⁶LiH to ⁶LiD increases. Received: 24 March 1999 / Accepted: 5 August 1999 / Published online: 15 December 1999     

Study of interference in the flame atomic absorption spectrometric determination of lithium by using factorial design

The severe interference of a number of metallic ions found in brines, marine sediments and sea water in the determination of lithium is demonstrated. Calcium, iron and sodium significantly depressed the absorption signal on lithium in an air/acetylene flame. Aluminium, magnesium and strontium up to 1500, 1000 and 200 μg/mL, respectively, showed no interference in the determination of lithium under the same conditions. Potassium produced some suppression of the lithium signal at levels in excess of 1500 μg/mL. Experimental data were examined using the factorial design method. Interference was demonstrated in two synthetic samples (models of “brine” and “marine sediments” ) and natural marine sediment. It was possible to eliminate all interferences using a higher temperature (nitrous oxide/acetylene flame). In addition, by using the standard addition method the interference disappeared, which confirmed the interference as a proportional systematic error. Received: 4 December 1998 / Revised: 3 March 1999 / Accepted: 6 March 1999     

Direct analysis of solid samples by graphite furnace atomic absorption spectrometry with a transversely heated graphite atomizer and D2-background correction system (SS GF-AAS)

An instrumental design for the analysis of heavy metals in solid samples (certified reference materials, river sediments, cements) by direct graphite furnace atomic absorption spectroscopy (SSGF-AAS) is presented and outlined. A high performance atomic absorption spectrometer with a D₂-background corrector and a transversely heated graphite atomizer was modified. Solid sampling was achieved by a mechanical module combined with an ultra microbalance. Cadmium, lead and chromium in different samples (sample weights between 20–400 μg) have been determined in the μg/g- to ng/g-range with the graphite-platform technique. Different ways of calibration and inhomogeneity problems are discussed. The precision of SSGF-AAS is equal to the precision of the conventional AAS-technique with chemical digestion (microwave digestion system, Zeeman-AAS). It is shown that SSGF-AAS is a reasonable alternative to the conventional technique for selected analytical problems. Received: 19 February 1997 / Revised: 30 May 1997 / Accepted: 4 June 1997     

Superfine Expanded Graphite with Large Capacity for Lithium Storage

A superfine expanded graphite (s‐EG) fiber material was investigated as an anode material for lithium‐based batteries. The fibers were prepared by decomposition of dicarbon monofluoride‐intercalated graphite. The high resolution transmission electron microscopy (HRTEM) images showed the fiber thickness in range of 2–3 nm with several microns in length. Lithium storage capacity in this material was measured in lithium half cells. High lithium storage capacity of about 1000 mAh · g^–1 at a rate of C/10, corresponding to Li₃C₆ composition was obtained. The material showed fairly good rate capability exhibiting lithium storage capabilities even at 60C. As a effect of ball milling, the s‐EG showed crystallographic ordering in the sample with reduced the lithium storage capacity corresponding to composition of LiC₆. A simple mathematical relation to account for the excess lithium storage capacity in this material is put forward.     

Li15Al3Si6 (Li14.6Al3.4Si6), a compound displaying a heterographite‐like anionic framework

The title compound, lithium aluminium silicide (15/3/6), crystallizes in the hexagonal centrosymmetric space group P6₃/m. The three‐dimensional structure of this ternary compound may be depicted as two interpenetrating lattices, namely a graphite‐like Li₃Al₃Si₆ layer and a distorted diamond‐like lithium lattice. As is commonly found for LiAl alloys, the Li and Al atoms are found to share some crystallographic sites. The diamond‐like lattice is built up of Li cations, and the graphite‐like anionic layer is composed of Si, Al and Li atoms in which Si and Al are covalently bonded [Si—Al = 2.4672 (4) Å].