煤和生物质共气化制备富氢气体的实验研究

在煤处理量为8kg/h的小型流化床反应器上,以富氧空气和水蒸气为气化介质,对煤和生物质共气化制取富氢燃气进行了实验研究。在850℃～1 050℃主要考察了空气当量比、水碳比、生物质比例和生物质种类对燃气组成和气体产率的影响。结果表明,对煤和稻草混合体系,稻草质量比为33%时,空气当量比增加,CO2含量显著增加,H2、CO和CH4含量减少,气体产率增加;水碳比增加,CO2和CH4含量增加,CO和H2含量减小,气体产率先增加后减小;生物质比例增加,CO2、H2和CH4含量增加,CO含量降低,气体产率先增加后减小,当生物质比例小于50%时,可以实现体系的稳定运行。对于三种不同的煤与生物质混合体系,煤与高粱秆共气化所得煤气中H2含量最高,气体产率的顺序为:煤/木屑煤/高粱秆煤/稻草煤。实验中H2在煤气中的体积分数最高可达37.25%,最大产率为0.54m3/kg。     

应用TG-FTIR联用研究催化剂对煤热解的影响

用TG-FTIR联用技术研究了碱金属、碱土金属和过渡金属对宝日希勒褐煤和包头烟煤热解的催化作用和挥发分析出的影响。结果表明，各种催化剂对褐煤和烟煤热解的催化效果分别为Ni>Fe~Ca>K和Ca~Fe>Ni>K，K2CO3对煤的热解没有明显的催化作用。催化剂使褐煤和烟煤热解转化率增加的最大值分别为10.1％和6.4％。烟煤热解生成的CH4比褐煤的多，不同的催化剂使煤热解挥发产物CO2、H2O、CH4和CO增加的幅度不一样，催化效果与温度和煤的变质程度有关。     

CH_4,CO_2和H_2O在非金属原子修饰石墨烯表面的吸附

煤层气(矿井瓦斯)是一种有望替代传统化石燃料,如煤、石油和天然气的非常规气体.作为可得的清洁能源,它的利用被认为是节能和经济的选择.在本工作中,非金属原子X(X=H,O,N,S,P,Si,F,Cl)修饰的石墨烯(Gr)被用来代表具有结构异性的煤表面模型.通过密度泛函理论系统地研究了煤层气组分Y(Y=CH4,CO2,H2O)在非金属原子修饰石墨烯上的吸附作用.结果表明Y在非金属原子修饰石墨烯上的吸附均为物理吸附.态密度和差分电荷密度共同表明了这种弱的相互作用.其中,H和Cl对CH4的作用较大;N、O、F、Cl对CO2的作用较强;N,Cl对H2O的影响不容忽视.总的来说,吸附能大小依次为:H2OCO2CH4.因此,在CH4富集的煤层里注入H2O或CO2可以与CH4形成竞争吸附,进而提高煤层气采收率.本工作提供了在分子水平下煤层气与非金属原子修饰石墨烯之间的相互作用的详情,并为煤层瓦斯的开采与分离提供了有用的信息.     

Quantitative behavior of vibrational excitation in AC plasma assisted dry reforming of methane

Quantitative behavior of non-equilibrium excitation by direct electron impact in low-temperature dry reforming of methane was investigated by integrated studies of experimental validation and kinetic modeling.A plasma chemistry kinetic mechanism incorporating the reactions involving vibrational excitation of CH4,CO2,H2 and CO molecules as well as the low temperature He/CH4/CO2 conversion pathways was developed and validated.The calculation results showed that at lower E/N values(<150 Td)large population of energized electrons generated in a He/CH4/CO2 discharge resulted in an intensification of vibrational excitation.Despite the large generation of vibration,the vibrationally excited molecules in a 0.5/0.25/0.25 of He/CH4/CO2 discharge mixture were easy to relax,due to the strong coupling of the vibration of different molecules in a gas mixture.The results showed that the moderate levels of the vibrational excitation,such as CO2(v10,11,...,18)and CO(v9,10),presented most efficient in the stimulation of species generation including CO,CH2 O,CH3 OH,C2 H4 and C2 H6.Specifically,under conditions of E/N of 108 Td,14.9%of CO formation was estimated from the recombination of CO2(v)with CH3 and H,CO2(v)+CH3→CH3 O+CO,CO2(v)+H→CO+OH.Also,4.8%of C2 H4 formation was from the recombination reaction CH4(v)+CH→C2 H4+H.These results highlight the strong roles of vibrational states in a complex plasma chemistry system.     

CO气氛下褐煤加压快速热解过程中CH_4的逸出规律

在管式反应器上进行了霍林河褐煤加压快速热解实验,研究了CO气氛下CH4逸出规律。在加压快速热解条件下,由于CO解离态吸附的O(a)吸附在煤上,提供了活性中心,电负性强的O(a)诱发其周围其他原子的电子云向O(a)偏移,减弱了原来化学键的强度,导致芳香环的开裂,侧链、醚键和脂肪链的断裂提供更多的自由基,稳定煤热解生成的碎片,促进了CH4的生成和逸出。因此,CO气氛下CH4产率较N2气氛下的高,在900℃、1.0 MPa时,50%CO气氛下的CH4产率较N2气氛下的提高了12.5%,并且CH4产率随着温度升高、压力的增大而增大。     

煤层气在含Al,Si,P和S煤结构模型上吸附的密度泛函理论研究

Al,Si,P和S掺杂石墨烯(X-Graphene,X-Gr,X=Al,Si,P和S)可用来代表具有结构异性的煤结构模型.通过自旋极化的密度泛函理论(DFT)方法,研究了煤层气(Coalbed methane,CBM,主要成分为CH4,CO2和H2O)在煤结构模型X-Gr上的吸附,并讨论了相应的吸附能、吸附平衡距离、Mulliken电荷转移、电荷密度差分图和态密度.结果表明,含Al和Si的煤结构模型对CBM的吸附较强,而CBM在P和S煤结构模型的吸附为弱的物理吸附.CBM在X-Gr煤结构模型上的吸附作用随着掺杂元素非金属性的增强而减弱,即Al-GrSi-GrP-GrS-Gr.煤层气中CO2和H2O吸附在煤炭表面的能力强于CH4,可以通过注入CO2和H2O到煤层中促进CH4的开采.此外,含Al和Si煤结构与煤层气之间较强的相互作用表明其可以作为CH4,CO2和H2O的气体传感器.     

BaCo0.7Fe0.2Nb0.1O3-δ膜反应器还原侧表面反应机理

研究了BaCo0.7Fe0.2Nb0.1O3-δ(BCFN)透氧膜反应器还原侧表面反应机理, 分析了表面催化微粒及催化床对膜反应器的作用. 提出了“催化解离机制”是构成甲烷重整BCFN膜反应器透氧量上升的主要原因; CH4, H2及CO在BCFN膜表面的反应活性依次为H2>CO>CH4; 当CH4气氛中加入H2或CO时, BCFN膜表面的主要发生由CH4直接氧化转变H2或CO的氧化反应, 同时极大提升了BCFN膜反应器的透氧量; BCFN膜表面氧化反应为“晶格氧”氧化反应模式主导.     

不同粒径的Ni/SiO2催化剂上CH4和CO2吸附活化的漫反射傅里叶变换红外光谱研究

 采用原位漫反射傅里叶变换红外光谱研究了CH4和CO2在不同粒径的Ni/SiO2催化剂上的吸附及活化. 结果表明,在不同粒径的催化剂上,检测到有CH4解离生成的CHx(x=1～3)物种,以及催化剂表面吸附的CHx物种与表面-OH 作用生成的CHx-O物种. CH4的裂解强烈依赖于催化剂表面Ni颗粒的大小,在粒径8 nm左右的Ni颗粒上, CH4较易解离; CO2难以直接在Ni/SiO2催化剂表面发生解离吸附,但CH4解离生成的吸附H对CO2的解离吸附具有明显的促进作用; CH4与CO2共吸附时,较小粒径的Ni可以促进CO2与表面氧物种发生反应,生成单齿表面碳酸盐物种.     

Rh/SiO_2催化剂上甲烷部分氧化制合成气的反应机理

采用原位Raman光谱技术,在原料气中的O2未完全耗尽的条件下,对CH4部分氧化制合成气反应的Rh/SiO2催化剂床层前部贵金属物种的化学态以及由CH4解离所生成的碳物种进行了表征.在此基础上采用脉冲反应和同位素示踪技术,比较了CH4的部分氧化及其与H2O和CO2的重整等反应对催化剂床层氧化区内CO和H2生成的相对贡献,并将实验结果与Ra-man光谱表征结果进行了关联.结果表明,在600°C下将还原后的4%Rh/SiO2催化剂切入CH4:O2:Ar=2:1:45原料气,催化剂床层前部未检测到铑氧化物的Raman谱峰,但可清晰检测到源于CH4解离的碳物种;在700°C和接触时间小于1ms的条件下,催化剂床层的氧化区内已有大量CO和H2生成,在相同的实验条件下,CH4与H2O或CO2重整反应对氧化区内合成气生成的贡献则很小;以CH4:16O2:H218O:He=2:1:2:95为原料气的同位素示踪实验结果表明,在原料气中16O2未完全耗尽的情况下,反应产物中C16O的含量占CO生成总量的92.3%,表明CO主要来自CH4的部分氧化反应.上述结果均表明,在O2存在下Rh/SiO2催化剂上CO和H2可以通过CH4直接解离和部分氧化机理生成.     

La2NiO4／Al2O3催化剂上CH4／CO2的重整

 通过溶胶－凝胶方法制备了尖晶石结构的La2NiO4／Al2O3催化剂，采用BET，XRD和TG表征了催化剂的孔分布、比表面积、体相组成以及凝胶样品的热失重和热分解过程．将催化剂应用于CH4／CO2重整反应制合成气，考察了惰性气体和反应温度对转化率、选择性以及积碳的影响．结果表明，在高空速（GHSV＝4．8×104ml／（g·h））下，CH4和CO2转化率分别为51％和60％，CO和H2的选择性约为98％和92％，惰性气体He的引入明显地提高了CH4和CO2的转化率．     

Gas permeability in rubbery polyphosphazene membranes

The synthesis, characterization, and gas permeability of 10 new polyphosphazenes has been studied. Additionally, the first gas permeation data has been collected on hydrolytically unstable poly[bis-(chloro)phosphazene]. Gases used in this study include CO₂, CH₄, O₂, N₂, H₂, and Ar. CO₂ was the most permeable gas through any of the phosphazenes and a direct correlation between the T_g of the polymer and CO₂ transport was noted with permeability increasing with decreasing polymer T_g. To a lesser degree, permeability of all the other gases studied also yielded increases with decreasing polymer T_g. The trend observed for these new polymers was further supported by published data for other phosphazenes. Furthermore, permeability data for all gases were found to correlate to the gas condensability and the gas critical pressures, except for hydrogen, suggesting that the nature of the gas is also a significant factor for permeation through rubbery phosphazene membranes. Ideal separation factors () for the CO₂/H₂ and CO₂/CH₄ gas pairs were calculated. For CO₂/CH₄, no increase in was observed with decreasing T_g, however increases in were noted for the CO₂/H₂ pair.     

Systematic investigation of the effects of temperature and pressure on gas transport through polyurethane/poly(methylmethacrylate) phase-separated blends

Polyurethane (PU) and polyurethane–poly(methylmethacrylate) (PMMA) blend membranes were used in gas separation studies. The effects of blend composition, temperature, and pressure on the permeability, diffusivity, and solubility of CO₂, H₂, O₂, CH₄, and N₂ were investigated. The separation factors of some gas pairs were also evaluated. Positron annihilation lifetime spectroscopy was applied to assess free volume changes as a function of blend composition and temperature. Free volume size increases by approximately 30% with increasing temperature from 10 to 40 °C for all blends studied. The permeability of all gases decreases by approximately 55% with the addition of 30 wt% of PMMA. The permeation process is governed by diffusion, except that of CO₂. In relation to the behavior of gas transport as a function of temperature, some important observations are (i) CO₂ presents the lowest permeation activation energy value (28 kJ/mol), and (ii) gas pair selectivity increases at low temperatures and is high for gas pairs that present differences in permeation activation energies as high as 15 kJ/mol for the CO₂/CH₄ gas pair. Furthermore, the study with pressure variations shows that: (i) at elevated pressure, the PU and the blend membrane permeability to CO₂ and H₂ increases by approximately 35%, and (ii) oxygen-to-nitrogen selectivity increases with pressure as a consequence of the decrease in the permeability to nitrogen in the case of the 30%-PMMA blend.     

含叔丁基聚酰亚胺均质膜的气体分离性能

采用高温“一步法”缩聚合成了一系列含叔丁基的可溶性芳香聚酰亚胺树脂, 然后通过溶液浇注法制得相应均质薄膜, 并对其气体分离性能进行了测试, 同时研究了二酐结构和温度对聚酰亚胺均质膜气体分离性能的影响. 结果表明, 对于H₂, N₂, O₂, CO₂和CH₄ 等5种气体, 含叔丁基聚酰亚胺均质膜不仅表现出良好的透气性, 而且具有较高的气体透过选择性, 4,4'-(六氟异丙烯)二酞酸酐(6FDA)和均苯四甲酸二酐(PMDA)两类聚酰亚胺均质膜的气体分离性能最佳. 除CO₂外, 这两类聚酰亚胺均质膜的气体渗透系数随温度升高而升高, 而所有测试气体在这两种均质膜中的扩散系数和溶解度系数均随温度升高而增大.     

Novel CO2 selectively permeating membranes containing PETEDA dendrimer

Pentaerythrityl tetraethylenediamine (PETEDA) dendrimer was synthesized from pentaerythrityl tetrabromide and ethylenediamine. Its molecular structure was characterized by elemental analysis, Fourier transform infrared resonance (FT-IR) and hydrogen nuclear magnetic resonance (¹H NMR) spectroscopy. The composite membranes for selectively permeating CO₂ were prepared by using PETEDA-PVA blend polymer as the active layer and polyethersulfone (PES) ultrafiltration membrane as the support layer and their permselectivity was tested by pure CO₂ and CH₄ gases and the gas mixture containing 10 vol.% CO₂ and 90 vol.% CH₄, respectively. For pure gases, the membrane containing 78.6 wt% PETEDA and 21.4 wt% PVA in the blend has a CO₂ permeance of 8.14 × 10⁻⁵ cm³ (STP) cm⁻² s⁻¹ cmHg⁻¹ and CO₂/CH₄ selectivity of 52 at 143.5 cmHg feed gas pressure. While feed gas pressure is 991.2 cmHg, CO₂ permeance reaches 3.56 × 10⁻⁵ cm³ (STP) cm⁻² s⁻¹ cmHg⁻¹ and CO₂/CH₄ selectivity is 19. For the gas mixture, the membrane has a CO₂ permeance of 6.94 × 10⁻⁵ cm³ (STP) cm⁻² s⁻¹ cmHg⁻¹ with a CO₂/CH₄ selectivity of 33 at 188.5 cmHg feed gas pressure, and a CO₂ permeance of 3.29 × 10⁻⁵ cm³ (STP) cm⁻² s⁻¹ cmHg⁻¹ with a CO₂/CH₄ selectivity of 7.5 at a higher feed gas pressure of 1164 cmHg. A possible gas transport mechanism in the composite membranes is proposed by investigating the permeating behavior of pure gases and the gas mixture and analyzing possible reactions between CO₂/CH₄ gases and the PETEDA-PVA blend polymer. The effect of PETEDA content in the blend polymer on permselectivity of the composite membranes was investigated, presenting that CO₂ permeance and CO₂/CH₄ selectivity increase and CH₄ permeance decreases, respectively with PETEDA content. This is explained by that with increasing PETEDA content, the carrier content increases, and the crystallinity and free volume of the PETEDA-PVA blend decrease that were confirmed by the experimental results of X-ray diffraction spectra (XRD) and positron annihilation lifetime spectroscopy (PALS).     

富氮多级孔炭材料的制备及其吸附分离CO2的性能

使用新型含氮聚合物席夫碱为炭源, SBA-15为模板,通过纳米铸型法原位合成微孔-中孔-大孔串联的多级孔富氮炭材料.材料的比表面积为752 m²·g^-1,孔容0.79 cm³·g^-1; X光电子能谱分析表明炭材料中的氮含量高达7.85%(w).将所制备的多孔炭材料应用于CO₂的吸附分离,发现炭材料的微孔发挥主导作用,表面氮掺杂发挥辅助作用.在两者的协同作用下, CO₂吸附量在常压、273 K下可达97 cm³·g^-1, CO₂/N₂和CO₂/CH₄的分离比(摩尔比)分别为7.0和3.2,低压亨利吸附选择性分别为23.3和4.2.采用Toth模型对单组分平衡吸附进行拟合,并根据理想溶液吸附理论(IAST)预测双组分CO₂/N₂和CO₂/CH₄混合气体的分离选择性分别为40和18.     

Gas transport property of polyallylamine–poly(vinyl alcohol)/polysulfone composite membranes

Polyallylamine (PAAm) was synthesized by free radical polymerization and characterized by Fourier transform infrared resonance (FT-IR) spectroscopy, hydrogen nuclear magnetic resonance (¹H NMR) spectroscopy and differential scanning calorimetry (DSC). The composite membranes were prepared by using PAAm–poly(vinyl alcohol) (PVA) blend polymer as the separation layer and polysulfone (PSF) ultrafiltration membranes as the support layer. The surface and cross-section morphology of the membrane was inspected by environmental scanning electron microscopy (ESEM). The gas transport property of the membranes, including gas permeance, flux and selectivity, were investigated by using pure CO₂, N₂, CH₄ gases and CO₂/N₂ gas mixture (20 vol% CO₂ and 80 vol% N₂) and CO₂/CH₄ gas mixture (10 vol% CO₂ and 90 vol% CH₄). The plots of gas permeance or flux versus feed gas pressure imply that CO₂ permeation through the membranes follows facilitated transport mechanism whereas N₂ and CH₄ permeation follows solution–diffusion mechanism. Effect of PAAm content in the separation layer on gas transport property was investigated by measuring the membranes with 0–50 wt% PAAm content. With increasing PAAm content, gas permeance increases initially, reaches a maximum, and then decreases gradually. For CO₂/N₂ gas mixture, the membranes with 10 wt% PAAm content show the highest CO₂ permeance of about 1.80 × 10⁻⁵ cm³ (STP) cm⁻² s⁻¹ KPa⁻¹ and CO₂/N₂ selectivity of 80 at 0.1 MPa feed gas pressure. For CO₂/CH₄ gas mixture, the membranes with 20 wt% PAAm content display the highest CO₂ permeance of about 1.95 × 10⁻⁵ cm³ (STP) cm⁻² s⁻¹ KPa⁻¹ and CO₂/CH₄ selectivity of 58 at 0.1 MPa feed gas pressure. In order to explore the possible reason of gas permeance varying with PAAm content, the crystallinity of PVA and PAAm–PVA blend polymers was measured by X-ray diffraction (XRD) spectra. The experimental results show an inverse relationship between crystallinity and gas permeance, e.g., a minimum crystallinity and a maximum CO₂ permeance are obtained at 20 wt% PAAm content, indicating that the possibility of increasing CO₂ permeance with PAAm content due to the increase of carrier concentration could be weakened by the increase of crystallinity.     

Poly(N,N-dimethylaminoethyl methacrylate)–poly(ethylene oxide) copolymer membranes for selective separation of CO2

A series of copolymers containing ether oxygen groups and amino groups were prepared based on N,N-dimethylaminoethyl methacrylate (DMEMA) and polyethylene glycol methyl ether methyl acrylate (PEGMEMA). The effect of PEGMEMA content in the copolymer on density, free volume, mechanical performance, and H₂, CO₂, N₂ and CH₄ gas transport properties of the copolymer was determined. Free volume was characterized using the polymer density and group contribution theory. The permeability of the copolymer to CO₂ is high, and both the CO₂/N₂ and CO₂/H₂ selectivities are high. For example, the permeability coefficient of PDMAEMA–PEGMEMA-90 (“90” represents the weight percent of PEGMEMA) to CO₂ is 112 Barrer and the CO₂/N₂ and CO₂/H₂ selectivity coefficients are 31 and 7, respectively. The effect of the temperature on gas transport properties was also determined. Finally, the potential application of the copolymer membranes for CO₂/light gases separation was explored.     

Dimeric Calix[4]resorcinarene-based Porous Organic Cages for CO2/CH4 Separation

Investigating gas separation by emerging porous organic cage(POC) solids is still on its initial stage. In this work, two novel [2+4] organic cages with distinguished structures have been prepared based on the Schiff-based condensation reaction between tetraformyl-functionalized calix[4]resorcinarene building blocks and xylylenediamine(XDA) isomers. Specifically, the use of para-position XDA affords lantern-shaped cage(CPOC-105) with a medium cavity of ca. 0.526 nm³, while the meta-position produces peanut-shaped structure(CPOC-106) with two small cavities of ca. 0.181 nm³. Both CPOC-105 and CPOC-106 exhibit high selectivity capture of CO₂ over CH₄ with calculated selectivity coefficients of 4.5 and 3.1, respectively, under ambient conditions, and are capable of separating CO₂/CH₄ mixtures by fixed-bed column breakthrough experiments.     

Characteristics of a zirconia composite membrane fabricated by a laser firing method

By a method of laser firing, a high zirconia containing (70%) composite membrane on porous ceramic tubing was successfully fabricated. The laser sintered composite membrane was characterized by gas separation/permeation experiments. In the separation experiment of a CO₂---CH₄ gaseous mixture, it was found that the separation factor of CH₄ over CO₂ was 1.15. In the pure gases permeation experiment, it was found that Knudsen diffusion is considered to be predominant in the permeation mechanism for pure gases H₂, He, CH₄, N₂, O₂, and CO₂, and the permeation mechanism of H₂O at lower temperature depends mainly on surface diffusion and on Knudsen diffusion at higher temperature.     

大气压等离子体射流重整CH4-CO2制合成气

采用大气压等离子体射流,以CH₄和CO^₂直接作为放电气体进行常压下重整制合成气的实验研究,考察了等离子体射流的放电特征及放电距离、放电功率、原料气配比和流量对反应的影响。结果表明,该等离子体具有放电稳定、均匀的特征。重整反应的主要产物为合成气,只有少量的H₂O和积炭生成。优化的反应条件为放电距离为9mm,CH₄和CO₂的摩尔比为4/6。当原料气流量为1000mL/min,放电功率为88.4W时,CH4和CO₂的最高转化率为分别为94.99%和87.23%。甲烷和二氧化碳的转化率随放电功率的增加而增加,随流量的增加而减少。