尼龙1O1O非等温结晶动力学过程的计算机模拟

根据ъорοхоъский提出的相似于Avrami方程的近似公式X=1-exp[-Z(at)n],采用加权最小二乘法,对尼龙1010非等温结晶动力学过程进行了模拟,编制了模拟非等温结晶动力学过程的软件.该软件可用于精确处理结晶动力学参数,也可用于计算机辅助教学.     

聚氧化乙烯(PEO)/聚双酚A羟基醚(PBHE)共混体系的非等温结晶动力学

本文联系Avrami方程和Ozawa方程,得出一个适合于非等温结晶动力学过程的新的基本方程,由这个方程可获得描述非等温结晶动力学过程的某些参数,并用DSC方法,对PEO/PBHE共混体系的非等温结晶动力学进行了研究,对实验结果进行了讨论.     

低密度聚乙烯/乙丙烯三元共聚(LDPE/EPO)共混体系的结晶动力学

用DSC方法研究了LDPE/EPO共混体系的等温及非等温结晶动力学,对LDPE/EPO共混体系的等温结晶动力学研究表明,共混物是三维生长的异相成核,共混物在各个结晶温度下的结晶过程都是以方式K_g(Ⅱ)进行的.采用联系Avrami方程和Ozawa方程导出的新非等温结晶动力学方程,处理了LDPE/EPO共混体系,得到了非等温结晶过程的一些基本参数,新方程很好地描述了此共混体系的非等温结晶动力学过程.     

高聚物非等温结晶动力学

由于等温ＤＳＣ法测定结晶动力学参数在实验上存在着一定的局限性，这些缺点可通过非等温ＤＳＣ法来克服。本文基于上述观点介绍了高聚物非等温结晶动力学的理论和实验方法，并对影响动力学过程的一些因素进行了讨论，对非等温结晶动力学的最新情况及发展倾向，应用情况作了介绍。     

苯乙烯-丙烯等规立构嵌段共聚物(iPS-b-iPP)的非等温结晶动力学的研究

用DSC法研究了苯乙烯-丙烯等规立构嵌段共聚物的非等温结晶动力学。结果表明:冷却速率在5～20℃/min范围内,共聚物的非等温结晶动力学参数能很好地符合Avrami动力学方程,非等温结晶速率常数与冷却速率有关,动力学结晶能力则同时受到冷却速率和共聚物组成比的影响。文中还讨论了在非等温结晶条件下共聚物的结晶成核和生长方式与共聚物组成和结构的关系。联合Avrami方程和Ozawa方程推导的非等温结晶动力学方程较好地描述了iPS-b-iPP嵌段共聚物的非等温结晶动力学过程。     

尼龙1218的等温及非等温结晶动力学研究

采用示差扫描量热计DSC考察了一种新型长烷基链偶偶尼龙 尼龙 12 18 自熔体的结晶过程 ,分别利用Avrami方程和Ozawa方程对等温及非等温结晶动力学进行了描述与研究 ,计算了相关的结晶动力学参数 ,得出相应的结晶机理 .最后计算了等温结晶活化能和非等温结晶活化能 ,依此得到烷基链段长度与尼龙结晶过程有密切关系     

己内酯和2,2-二羟甲基丁酸共聚酯的非等温结晶动力学研究

采用示差扫描量热仪(DSC) 研究了具有生物相容性及可降解性P(BHB-CL)超支化共聚酯的非等温熔融结晶过程, 分别采用Avrami 方程、Ozawa 方程和Mo方程对P(BHB-CL)共聚酯的非等温动力学数据进行比较分析, 计算了相关的非等温结晶动力学参数, 并利用Kissinger方程计算其非等温结晶活化能. 结果表明, Mo方程更适合描述P(BHB-CL)共聚酯的非等温结晶过程.     

PA6T的非等温结晶动力学

采用示差扫描量热仪(DSC)考察了PA6T的非等温熔融结晶过程,分别采用Avrami方程、Ozawa方程及Mo提出的新方程对PA6T的非等温动力学数据进行比较分析,计算了相关非等温结晶动力学参数和非等温结晶活化能。结果表明:对于PA6T,用Mo法处理得到的结果更理想。     

聚苯硫醚/纳米二氧化硅复合材料的非等温结晶动力学及动态力学性能

用DSC法研究了聚苯硫醚（PPS）及其纳米SiO2复合材料的非等温结晶动力学,分析了结晶峰值温度Tp以及结晶起始温度T0等参数,并采用莫志深方程研究了复合材料的非等温结晶动力学。结果表明,莫志深方程能够较好地描述复合材料的非等温结晶动力学,纳米SiO2在PPS基体中起异相成核作用,而使得纳米复合材料的结晶速率明显快于纯聚合物的结晶速率。动态力学分析研究结果表明,纳米SiO2的加入提高了PPS的储能模量,Tg向高温方向移动,说明纳米SiO2与PPS之间存在着较强的相互作用。     

聚合物结晶动力学

本文介绍了聚合物等温及非等温结晶动力学过程的理论和实验方法，对影响动力学过程的一些因素进行了讨论。     

Crystallization of poly(vinyl alcohol) during solvent removal: Infrared characterization and mathematical modeling

Crystallization of semicrystalline polymer films during drying has a significant effect on the rate of solvent removal. Understanding and controlling the crystallization kinetics is important in controlling residual solvent levels and drying kinetics. The degree of crystallinity of the poly(vinyl alcohol) films during multicomponent drying was investigated using Fourier transform infrared spectroscopy (FTIR). The 1141 cm^?1 band is sensitive to the degree of crystallinity of the polymer and the growth of intensity of this band was monitored as drying progressed. The results from the FTIR studies were comparable to the results obtained from differential scanning calorimetry. Studies were conducted to test the effect of initial solvent composition (water–methanol mixture), drying temperature, and polymer molecular weight on the rate of crystallization and the final crystallinity of the films. An increase in initial methanol composition increased the crystallization rate but did not affect the final degree of crystallinity. An increase in drying temperature and decrease in polymer molecular weight increased the rate of crystallization as well as the final degree of crystallinity. Based on the experimental data, rate constants for crystallization kinetics were extracted from our previously developed model based on free volume theory. The experimental data and the simulation results showed good agreement. The ability of the free volume theory to illustrate the crystallization behavior validated the model and improved its capability. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 930–935, 2007     

Computer simulation of crystallization kinetics and morphology in fiber-reinforced thermoplastic composites. I. Two-dimensional case

A body of experimental evidence suggests that reinforcing fibers influence both the crystallization kinetics and morphology of those composite materials that are based on crystallizable thermoplastics. The absence of an analytical model to predict the effect of fibers on crystallization has hindered data analysis. A new approach, using computer simulation of polymer crystallization, makes it possible to study the influence that reinforcing fibers have on the crystallization kinetics and morphology of semicrystalline polymers. Fibers depress the crystallization rate relative to an unreinforced polymer since they constrain spherulitic growth by an impingement mechanism. On the other hand, reinforcing fibers can also enhance crystallization rate by providing added surface nucleation sites. This work describes a two-dimensional simplification of the crystallization process that occurs in bulk materials. It is demonstrated that the relative bulk and fiber nucleation densities, in addition to the fiber fraction, fiber diameter, and spherulitic growth rate control the crystallization kinetics and also the spherulitic and transcrystalline morphologies that develop in reinforced thermoplastic composites. © 1993 John Wiley & Sons, Inc.     

Computer simulation of crystallization kinetics and morphology in fiber-reinforced thermoplastic composites. II. Three-dimensional case

A three-dimensional computer simulation has been used to predict crystallization kinetics and crystalline morphology in composite materials that are based on crystallizable thermoplastics. Reinforcing fibers in three-dimensional simulations show similar behavior to those in two-dimensional simulations; fibers suppress crystallization relative to an unreinforced polymer since they constrain spherulitic growth by an impingement mechanism, and also enhance crystallization by providing added surface nucleation sites. The effects of varying controlling parameters on crystallization kinetics and morphology are qualitatively the same as those observed in the two-dimensional case. The relative bulk and fiber nucleation denisities, in addition to the fiber volume fraction, fiber diameter, and spherulitic growth rate control the crystallization kinetics and crystalline morphology that develop in reinforced thermoplastic composites. It is more difficult to achieve the transcrystalline morphology in slices of three-dimensional composites than it is in two-dimensional composites because nuclei in 3-D systems are not constrained to positions in or near a 2-D plane. © 1993 John Wiley & Sons, Inc.     

动力学过程的精确模拟

采用加权最小二乘法更精确地模拟了化学动力学过程,结出了几种常见动力学模型的权重函数。用普通最小二乘法和加权最小二乘法对聚时苯二甲酸乙二酯的结晶动力学过程进行了处理。方差分析表明,两种加权最小二乘法的标准差均小于普通最小二乘法的标准差,所得斜率和截距也有明显不同,示出了模拟的相对结晶度及其导数曲线。     

半结晶聚合物注射成型中结晶动力学的数值模拟

对半结晶聚合物注射成型过程及其结晶过程进行偶合模拟,分析了二者的相互影响.具体是在注射成型数值模拟中考虑结晶动力学效应,分别在本构方程、能量方程及材料物性参数方程中引入反映结晶效应的参数;同时在结晶动力学计算中考虑流动诱导效应,从能量的角度提出并使用修正的动力学模型,用材料流动过程的耗散能表征流动对结晶的影响.通过对等规聚丙烯(iPP)和聚对苯二甲酸乙二醇酯(PET)两种半结晶聚合物注射过程模拟结果的分析比较,证实成型过程具有加速结晶的作用.同时,材料的结晶也对注射成型加工过程,尤其是保压与冷却过程的温度场分布有较大的影响.     

取向聚对苯二甲酸乙二酯纤维的非等温结晶动力学

取向聚对苯二甲酸乙二酯纤维的非等温结晶动力学张志英，赵家森（天津纺织工学院材料科学系天津３００１６０）关键词取向高聚物，聚对苯二甲酸乙二酯，非等温结晶，结晶动力学研究高聚物结晶动力学常用的等温方法有光透射法、密度法、显微镜法、Ｘ－射线衍射法、差示扫描...     

Interpretation of the nonisothermal crystallization kinetics of polypropylene using a power law nucleation rate function

A nucleation rate function is proposed for use in analyzing the overall crystallization kinetics of polymers. This function allows for the possibility that the nucleation rate varies substantially during the crystallization. This feature is particularly useful in analyzing nonisothermal crystallization, but it can be used to analyze isothermal crystallization as well. The nucleation rate function was used in the derivation of a modified transformation kinetics equation of the Avrami type. The modified Avrami equation was found to be suitable for kinetics analysis for the data obtained from nonisothermal crystallization at rapid cooling rates. Kinetics parameters used to describe nonisothermal crystallization under rapid cooling rates are presented and discussed. These include crystallization induction time, plateau (crystallization) temperature, crystallization half-time, crystallization rate constant, Avrami index, and newly defined quantities called nucleation index, geometric index, and nucleation rate constant. The procedure used to obtain the nucleation rate constant and nucleation index for the nucleation rate function is described and illustrated by application to the analysis of the crystallization kinetics of polypropylene. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 1077–1093, 1997     

Computer simulation of crystallization kinetics and morphology in fiber-reinforced thermoplastic composites. III. Thermal nucleation

A computer simulation has been used to predict crystallization kinetics and crystalline morphology in composite materials based on thermally nucleated crystallizable matrices. As demonstrated for athermally nucleated composites, the presence of reinforcing fibers increases the complexity of the system. Fibers are shown to have a dual effect on the spherulitic crystallization process. The influence that fibers have depends on the interplay between the enhancing effects that fibers have on nucleation and the depressing effects that fibers have on spherulitic growth. Fibers that do not provide additional nuclei to the system depress the rate of crystallization relative to an unreinforced polymer, while fibers that add nuclei to the system increase the rate of crystallization. The transcrystalline morphologies that develop in thermally nucleated fiber-reinforced polymers are controlled primarily by the relative numbers of bulk and fiber nuclei. The extent of transcrystalline regions can be suppressed either by increasing the rate of bulk nucleation, or by decreasing the rate of fiber nucleation. Finally, the qualitative appearance of the morphology in the transcrystalline region was found to be indicative of the mode of fiber nucleation. © 1995 John Wiley & Sons, Inc.