化学气相输运法制备ZnO晶体

采用化学气相输运法在常压开放系统中,以ZnO粉体为原料,HCl和NH3为输运气体,O2和H2O为反应气体,适度过量的HCl作为刻蚀性气体,在(0001)方向的蓝宝石籽晶片上制备了(0002)方向定向生长的ZnO晶体,且a、b轴生长速度明显高于c轴方向.以(0002)方向的ZnO籽晶片作基片,制备了ZnO单晶厚膜,晶体呈螺旋状外延生长,正极面的单晶摇摆曲线半高宽为543.6弧秒.     

常压化学气相输运法合成Zn1-xCoxO晶体

本文采用高温化学气相输运法,温度970℃,在蓝宝石和石英基片上制备Zn1-xCoxO晶体.电子扫描显微镜(SEM)观察发现,蓝宝石晶片上的晶体形貌较SiO2 晶片上的规整,晶体呈现六棱柱或六棱锥体,一般显露柱面m{101-0}、正锥面p{101-1}、负极面c{0001-}和正极面c{0001},晶体表面光滑.在石英基片上得到的Zn1-xCoxO晶体生长的棱面较模糊,基片的部分晶体非定向密集生长,连续形成薄膜结构.X衍射证实晶体为ZnO纤锌矿结构.X光能谱﹙EDS﹚测量表明 ZnO 晶体有钴离子的存在,且浓度随原料中的Co2O3:ZnO的比值增大而增加 .     

In和过渡金属离子共掺杂对ZnO晶体形貌的影响

采用水热法,KOH作矿化剂,在ZnO前驱物中添加适量的CoCl2·6H2O,FeCl2·4 H2O,NiCl2·6H2O,In2O3,其中Co:In:Zn,Fe:In:Zn,Ni:In:Zn 分别为5:1:100,5:1:100,3:1:100.3 mol/L KOH作矿化剂,温度430 ℃,填充度35;,反应24 h,制备了In和过渡族金属离子共掺的ZnO晶体.结果表明,掺杂In2O3时,所合成的过渡族金属离子掺杂的ZnO晶体均呈现六角片状晶体,晶体形貌规则,表面光滑,直径为5～10 μm.和未掺杂In的晶体相比,掺杂In后,晶体c轴极性生长速度得到明显的控制,a、b轴方向生长速度提高,大面积显露+c{0001}、负极面-c{0001}面,另外还显露正锥面+p{1011}、负锥面-p{101-1-}.     

Sn掺杂对ZnO晶体形貌和磁性的影响

采用水热法,在ZnO中添加SnCl2.2H2O作前驱物,3M KOH作矿化剂,温度430℃,填充度35%,反应24h,合成了掺杂Sn的ZnO晶体。当前驱物中添加SnCl2.2H2O可以明显影响部分晶体形态,使正极面c轴方向的生长速度受到抑制,较大面积显露正极面c{0001},同时也显露负极面-c{000 1}、正锥面p{10 10}、负锥面-p{101 1}和柱面m{10 10}。磁性测量结果显示Sn可微量掺入ZnO晶格中,且呈现顺磁性特征。X射线衍射和X光荧光能谱分析表明,SnCl2.2H2O的添加量较大时,还伴随生成金红相SnO2棒状晶体。     

碱土金属离子对ZnO极性生长的影响

本文采用水热法,以3mol/L KOH为矿化剂,填充度35%,温度430℃,通过添加适量比例的MgCl2.7H2O和CaO,合成了非极性生长的ZnO晶体。当Mg2 :Zn2 =2%和Ca2 :Zn2 =2~3%时,晶体c轴方向生长速度明显减弱,{0001}方向的极性生长得到控制,所合成的晶体大面积显露正极面 c{0001},同时显露负极面-c{1001-}、正锥面 p{101-1}、负锥面-p{101-1-}和柱面m{101-0}。X光能谱(EDS)没有检测到晶体中含有碱土金属离子。     

MOCVD法制备一维定向ZnO晶须阵列及掺杂研究

采用大气开放式MOCVD技术,以Zn(C5H7O2)2为前驱物,在玻璃和单晶硅基片上生长了沿c轴高度定向、规则排布的氧化锌晶须阵列.在此基础上,采用多气路输送不同金属有机源的方法,进行了ZnO晶须的掺杂,制备了掺铝元素的一维定向晶须阵列.XRD结果表明未掺杂ZnO晶须为六方纤锌矿结构,沿c轴高度取向;掺铝ZnO晶须晶体结构仍为六方纤锌矿结构,沿c轴择优取向.SEM结果显示,未掺杂的ZnO晶须阵列排布规则,长径比达到20;掺杂ZnO晶须随着铝掺杂浓度的增加,晶须的形貌及排布规则性变差.     

水热法合成Zn1-xMnxO：Sn和Zn1-x-yMnxCoyO：Cu晶体的磁性

本文采用水热法,以ZnO为前驱物,添加适量的MnCl2·4H2O、SnCl2·2H2O和MnCl2·4H2O、CoCl2·6H2O、CuCl2·2H2O,3 mol/L KOH作矿化剂,430℃反应24 h,分别合成了Zn1-xMnxO:Sn晶体和Zn1-x-yMnxCoyO:Cu晶体.用扫描电镜(SEM)对合成物形貌进行分析,结果表明,Zn1-MnxO:Sn晶体为六棱柱状晶体,直径约为10 μm,较大面积显露正极面c{0001},同时也显露负极面-c{0001}、正锥面p{1011}、负锥面-p{1011}和柱面m{1010}.Zn1-x-yMnxCoyO:Cu晶体也显露负极面-c{0001}、正锥面p{1011}、负锥面-p{1011}和柱面m{1010},{0001}显露面小于{0001}.X射线能谱(EDS)分析表明晶体主要成分为ZnO,Mn2 、Co2 离子掺杂量超过2%;SQUID磁性测量显示所合成晶体在25 K具有反铁磁特征,高温为顺磁性.     

常压化学水解反应生长氧化锌晶体

采用ZnCl2·2H2O在常压下高温水解反应生长ZnO晶体,反应温度为500℃.当以SiC为衬底时,可以获得六棱柱形氧化锌晶体,直径约为10μm,长为30～100 μm.当衬底为蓝宝石时,氧化锌沿[0001]呈定向柱状生长,柱的直径为5～10 μm,柱之间具有较多的内部缺陷.当以ZnO为衬底时,在{0001}面,形成连续膜,表面扫描电镜分析表明,晶体具有明显的极性生长特征,[0001]方向呈螺旋柱状生长.在{0001}面,晶体的平整性较好,呈现台阶性生长.     

晶体(NH4)2C4H4O6:VO2+的EPR参量及局域结构的研究

采用叠加模型和双旋-轨耦合参量模型,建立了结构参数与EPR参量之间的定量关系;较好地解释了[VO(H2O)5]2+络离子的局域结构和EPR参量;研究结果发现,(NH4)2C4H4O6:VO2+晶体中络离子[VO(H2O)5]2+的键长为R//≈0.130nm,R⊥≈0.195nm;在(NH4)2C4H4O6:VO2+晶体中,局域结构沿C4轴方向呈压缩的八面体结构;所得EPR参量的理论计算与实验测量数据符合很好.     

晶体(NH_4)_2C_4H_4O_6∶VO~(2 )的EPR参量及局域结构的研究

采用叠加模型和双旋-轨耦合参量模型,建立了结构参数与EPR参量之间的定量关系;较好地解释了[VO(H2O)5]2 络离子的局域结构和EPR参量;研究结果发现,(NH4)2C4H4O6:VO2 晶体中络离子[VO(H2O)5]2 的键长为R//≈0.130nm,R⊥≈0.195nm;在(NH4)2C4H4O6:VO2 晶体中,局域结构沿C4轴方向呈压缩的八面体结构;所得EPR参量的理论计算与实验测量数据符合很好。     

First-principles coexistence simulations of supercooled liquid silicon

We perform first-principles coexistence simulations of the low-density and the high-density phases of supercooled liquid silicon and find a negative slope for the coexisting line in the temperature-pressure plane. Electron density maps and electron-localization function plots of the two phases of silicon show marked differences. The calculated differences suggest more localized electrons in the low-density liquid compared to the high-density liquid, coming from an increased population of covalent bonds, which further explain the calculated negative slope in the two phase coexistence regime. This is consistent with the presence of a pseudo-gap in low-density liquid silicon, absent in the high-density liquid which shows a metallic behavior.     

Triethyl ammonium salt of O,O′-bis(p-tolyl)dithiophosphate, [Et3NH]+[(4-MeC6H4O)2PS2]−

Triethyl ammonium Salt of O,O′-bis(p-tolyl)dithiophosphate and O,O′-bis(m-tolyl)dithiophosphate have been obtained by reaction of p- and m-cresol, respectively with P₂S₅ in toluene and have been characterized by elemental analysis, IR, ¹H and ³¹P NMR spectroscopy. The molecular structure of O,O′-bis(p-tolyl)dithiophosphate has been determined. Crystal data: [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻: Monoclinic, P2₁/c, a=15.2441(9) ?, b=10.415(2) ?, c=3.9726(9) ?, β=91.709(7)°, V=2217.5(1) ?⁻³, Z=4.Supplementary materials Additional material available from the Cambridge Crystallographic Data Centre (CCDC no. 600927 for [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻ comprises the final atomic coordinates for all atoms, thermal parameters, and a complete listing of bond distances and angles. Copies of this information may be obtained free of charge on application to The Director, 12 Union Road, Cambridge CB2 2EZ, UK (fax: +44-1223-336033; email: deposit@ccdc.cam.ac.uk or www:http://www.ccdc.cam.ac.uk).     

Crystal structures of thecis andtrans isomers of dithiahexahydro[3.3]metacyclophane

Structures of both thecis andtrans isomers of dithiahexahydro[3.3]metacyclophane, ?C₆H₄?CH₂SCH₂?C₆H₁₀?CH₂SCH₂?, have been determined, wherecis andtrans refer to the attachments to the cyclohexane ring. Thecis form crystallizes in the monoclinic space groupP2₁/c witha=8.4299(11)Å,b=21.772(2)Å,c=8.9724(13)Å, β=116.574(11)^o, andZ=4. Thetrans isomer packs into the monoclinic space groupP2₁ witha=8.159(16)Å,b=10.185(5)Å,c=9.558(2)Å, β=112.435(18)^o, andZ=2. The cyclohexane ring of thecis isomer is in the chair conformation, while the cyclohexane of thetrans isomer is found in a twisted boat conformation.     

CTAB与SDBS对碳酸锶粒子生长形态调控及机理研究

以表面活性剂CTAB和SDBS为化学添加剂,采用化学共沉淀法对碳酸锶晶体的生长形态进行调控,成功地制备出了实心的树枝状和花瓣为空心的花状碳酸锶粉体,并用X射线衍射(XRD)、扫描电子显微镜(SEM)和傅里叶变换红外光谱(FT-IR)等分析手段对样品进行了表征;最后重点对化学添加剂可能产生的影响机理进行了初步的探讨.结果表明,CTAB和SDBS在晶体生长的过程中能起到显著的影响作用,两者对粒子分散性能的作用效果相反,而且后者对晶体(013)和(213)晶面表面能降低的贡献明显大于前者.     

Crystal structures of the cis and trans isomers of a tetrathia[3.3.3.3]cyclophane

Both the cis and trans isomers of 3,11,18,26-tetrathiatricyclo[26.2.2.1^5,9.2^13,16.1^20,24] hexatriaconta-5,7,9,20,22,24-hexene have been prepared and structurally characterized. Each of these centrosymmetric tetrathia dimers includes two cyclohexane rings in chair conformations with either 1,4-cis or 1,4-trans bonding and two meta-substituted benzene rings. The cis isomer packs into the monoclinic space group P2₁/a with a = 10.485(3)Å, b = 10.3956(18)Å, c = 14.1343(10)Å, = 105.200(13)°, Z = 2 and refined to an R factor of 0.046. The trans isomer crystallizes in the monoclinic space group P2₁/c with a = 10.7217(12)Å, b = 5.6797(7)Å, c = 25.415(5)Å, = 96.001(12)°, Z = 2 and refined to an R factor of 0.043. In the cis structure each benzene ring faces a cyclohexane ring while in the trans structure the cyclohexane rings face one another.     

Crystal structure of Zn4Na(OH)6SO4Cl·6H2O

The structure of Zn₄Na(OH)₆SO₄Cl·6H₂O, a secondary mineral from Hettstedt, Germany, was determined by single-crystal X-ray diffraction. The crystals are hexagonal,a=8.413(8),c=13.095(24) Å, space group $P\bar 3$ , Z=2. The structure was refined to R=0.0554 and R_w=0.0903 for 970 reflections with I≥3σ(I). The structure can be described as zinc hydroxide layers perpendicular toc, from which sulfates and chlorides extend. The layers are held together by a system of hydrogen bonds involving hexaaquo Na⁺ ions which occupy the interlayer space.     

Synthesis and Crystal Structure of 5-[2-(6-bromonaphthalenyloxymethyl)]-3-(4-morpholinomethyl)-1,3,4-oxadiazole-2(3<Emphasis Type="Italic">H</Emphasis>)-thione

Abstract  The title compound, C₁₈H₁₈BrN₃O₃S, a derivative of 1,3,4-oxadiazole, crystallizes in the triclinic space group P-1 with unit cell parameters a = 6.8731(3), b = 8.9994(4), c = 15.7099(6) ?, α = 92.779(3)°, β = 130.575(3)°, γ = 107.868(4)°, Z = 2. The dihedral angle between the mean planes of the planar naphthyl and morpholine (chair) rings with the planar oxadiazol ring is 50.1(8) and 76.8(6)°, respectively. The planar naphthyl ring is twisted 52.2(5)° with the mean plane of the morpholine ring. A group of four intermolecular close contacts are observed between a bromine atom and hydrogen atoms from the closely packed naphthyl, morpholine and oxy–methyl groups in the unit cell. These molecular interactions in concert with an additional series of π–π stacking interactions that occur between the center of gravity of the two 6-membered rings of the naphthalene group influence the twist angles of each of these three groups. A MOPAC AM1 calculation of the conformation energy of the crystal structure [226.0128(9) kcal] compared to that of the minimum energy structure after geometry optimization [29.9744(1) kcal] reveals a significantly reduced value. The twist angles of the three groups above also change after the AM1 calculation giving support to the influence of both intermolecular C–H···Br short-range interactions and Cg π–π stacking interactions on these angles which therefore play a role in stabilizing crystal packing. Graphical Abstract  Crystal structure of 5-{[(6-bromonaphthalen-2-yl)oxy]methyl}-3-(morpholin-4-ylmethyl)-1,3,4-oxadiazole-2(3H)-thione, C₁₈H₁₈BrN₃O₃S, is reported and its geometric and packing parameters described and compared to a MOPAC computational calculation. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

电沉积法制备ZnO纳米棒阵列及其发光特性

本文以掺F的SnO2导电玻璃为基板,以硝酸锌水溶液为电解液,采用三电极恒电位体系电沉积制备ZnO纳米棒阵列,系统考察了硝酸锌浓度和沉积电位等工艺参数对ZnO纳米棒阵列的微观形貌及其发光性能的影响规律.结果表明,硝酸锌浓度和沉积电位对纳米棒阵列的形貌有显著影响,控制适宜的工艺条件可以制备出直径分布均匀、结晶性好且纯度高的六方纤锌矿ZnO纳米棒阵列.荧光光谱分析表明,电沉积制备出的ZnO纳米棒阵列在385 nm附近有一个强荧光发射峰,且发光性能稳定、对纳米棒阵列微观形貌的细微变化不敏感,使其在发光二极管和激光器等领域具有广阔的应用前景.     

Crystal structure of irisolidone from the flowers of Pueraia lobata

Irisolidone (5,7-dihydroxy-6,4′-dimethoxyisoflavone) was isolated from the flowers of Pueraia lobata and its crystal structure was examined by X-ray single crystal diffraction. The crystal structure of irisolidone is monoclinic, space group P2₁/c with a = 15.491(9) ?, b = 7.895(4) ?, c = 13.321(7) ?, β = 110.546(9)° and Z = 4. Hydrogen bonding and aromatic π–π stacking assemble the title compound into a three-dimensional networking structure.