Experimental Investigation of the Nonlinear Response of a Hanging Cable. Part I: Local Analysis

An experimental model of an elastic cable carrying eight concentrated masses and hanging at in-phase or out-of-phase vertically moving supports is considered. The system parameters are adjusted to approximately realize multiple 1:1 and 2:1 internal resonance conditions involving planar and nonplanar, symmetric and antisymmetric modes. Response measurements are made in various frequency ranges including meaningful external resonance conditions. A local analysis of the system response is made on the basis of numerous amplitude-frequency and amplitude-forcing plots obtained in different ranges of the control parameter space. Attention is mainly devoted to the detection of the main features of the regular motions exhibited by the system, and to the analysis of the relevant phenomena of nonlinear modal interaction, competition, and local bifurcation between planar and nonplanar regular responses. The resulting picture appears very rich and varied.     

Nonlinear Dynamics of a Beam on Elastic Foundation

The nonlinear dynamics of a simply supported beam resting on a nonlinear spring bed with cubic stiffness is analyzed. The continuous differential operator describing the mathematical model of the system is discretized through the classical Galerkin procedure and its nonlinear dynamic behavior is investigated using the method of Normal Forms. This model can be regarded as a simple system describing the oscillations of flexural structures vibrating on nonlinear supports and then it can be considered as a simple investigation for the analysis of more complex systems of the same type. Indeed, the possibility of the model to exhibit actually interesting nonlinear phenomena (primary, superharmonic, subharmonic and internal resonances) has been shown in a range of feasibility of the physical parameters. The singular perturbation approach is used to study both the free and the forced oscillations; specifically two parameter families of stationary solutions are obtained for the forced oscillations.     

Whirling of a forced cantilevered beam with static deflection. II: Superharmonic and subharmonic resonances

Secondary resonances of a slender, elastic, cantilevered beam subjected to a transverse harmonic load are investigated. The effects of nonlinear curvature, nonlinear inertia, viscous damping and static load are included. Cubic terms in the governing equations lead to subharmonic and superharmonic resonances of order three. The static displacement produced by the weight of the beam introduces quadratic terms in the governing equations, which cause subharmonic and superharmonic resonances of order two. Out-of-plane motion is possible in all of these secondary resonances when the principal moments of inertia of the beam cross section are approximately equal.     

Nonlinear Dynamics of a Rigid Unbalanced Rotor in Journal Bearings. Part II: Experimental Analysis

In the first part of the present investigation [9], the dynamic behaviour of a rigid rotor supported on plain journal bearings was studied, focusing particular attention on its nonlinear aspects. In the present paper an experimental confirmation of the theoretical results is sought. The steel rotor of the experimental rig was given a constant circular cross section in order to fix in an easy way the two distances between supports corresponding, respectively, to the values of the parameter assigned in [9]. Two steel rings, each one with a series of holes and a clamping screw, were mounted onto the rotor with a small clearance. This arrangement made it possible to fix the positions of the rings and their holes respect to the rotor, so as to realize a pre-estabilished unbalance. The two bronze journal bearings were characterised by a relatively low length/diameter ratio, and a relatively high value of the radial clearance and were lubricated with oil delivered from a thermostatic tank. In this way, despite the relative lightness of the rotor, the dimensionless static eccentricity _s was given the high values that were apt to realize the operating conditions assumed in the theoretical analysis. The rotor was driven by means of a d.c. motor connected to a toothed belt-drive. Varying the rotor speed in the range 1000 ÷ 10000 r.p.m., made it possible to assign the values of the modified Sommerfeld number assumed in the theoretical analysis. Three pairs of eddy-current probes were mounted in order to detect the trajectories of three points (C₁, C and C₂) suitably fixed along the rotor axis. These orbits were finally put in comparison with the corresponding ones previously obtained through numerical analysis. The comparison pointed out that the experimental data were in good agreement with the theoretical predictions, despite the approximations that characterise the theoretical model and the unavoidable errors affecting measures in the course of the experimental test.     

钢筋混凝土剪力墙单元非线性分析模型及其应用

本文简要评述了几种常见的钢筋混凝土剪力墙非线性宏观单元模型后，着重对多垂直杆剪力墙非线性单元模型的几个重要问题如剪力变形的考虑方法，单元刚度矩阵的形式，垂直拉压杆及剪切弹簧的恢复力模型等进行了探讨与改进，最后给出了一个算例，并与试验结果比较，表明非线性宏观墙单元模型具有较好的计算精度。     

Dynamics of a Rigid Unbalanced Rotor with Nonlinear Elastic Restoring Forces. Part II: Experimental Analysis

In Part I, theoretical analysis of the dynamic behaviour of a rigid rotor with nonlinear elastic restoring forces was carried out. In this part (Part II), an experimental confirmation of the theoretical data from that analysis was sought. With this aim, an experimental model was set up consisting mainly of a practically rigid rotor clamped onto a small diameter piano wire symmetrical to the wire supports. These supports were rigid and equipped with roller bearings and a device that made it possible to adjust the initial tension in the wire so as to make the elastic restoring forces less or more linear. The rotor was dynamically unbalanced and was driven by an asynchronous motor regulated by means of an inverter in order to adjust the rotor speed. A series of tests was performed on this rig with different values of the initial tension in the wire, and the trajectories of two points on the rotor axis were recorded in the course of the tests. These trajectories were obtained, under the hypothesis of similarity, from the orbits covered by two given sections of the wire and detected with two pairs of capacitive transducers. The collected data was compared with the theoretical results from Part I of the present investigation. Comparison of the collected data with the corresponding theoretical results made it possible to infer that system nonlinearity in the presence of small damping can give rise to motions that are periodic, whether synchronous or not, or quasi-periodic, but never chaotic.     

Global Bifurcations and Chaotic Dynamics in Nonlinear Nonplanar Oscillations of a Parametrically Excited Cantilever Beam

This paper presents the analysis of the global bifurcations and chaotic dynamics for the nonlinear nonplanar oscillations of a cantilever beam subjected to a harmonic axial excitation and transverse excitations at the free end. The governing nonlinear equations of nonplanar motion with parametric and external excitations are obtained. The Galerkin procedure is applied to the partial differential governing equation to obtain a two-degree-of-freedom nonlinear system with parametric and forcing excitations. The resonant case considered here is 2:1 internal resonance, principal parametric resonance-1/2 subharmonic resonance for the in-plane mode and fundamental parametric resonance–primary resonance for the out-of-plane mode. The parametrically and externally excited system is transformed to the averaged equations by using the method of multiple scales. From the averaged equation obtained here, the theory of normal form is applied to find the explicit formulas of normal forms associated with a double zero and a pair of pure imaginary eigenvalues. Based on the normal form obtained above, a global perturbation method is utilized to analyze the global bifurcations and chaotic dynamics in the nonlinear nonplanar oscillations of the cantilever beam. The global bifurcation analysis indicates that there exist the heteroclinic bifurcations and the Silnikov type single-pulse homoclinic orbit in the averaged equation for the nonlinear nonplanar oscillations of the cantilever beam. These results show that the chaotic motions can occur in the nonlinear nonplanar oscillations of the cantilever beam. Numerical simulations verify the analytical predictions.     

Spontaneous radial capillary impregnation across a bank of aligned micro-cylinders. Part II: Experimental investigations

This paper presents an experimental approach to study the capillary impregnation of a liquid across an array of parallel micro-cylinders. The technique presented successfully validates the theoretical findings of part I, and provides a methodology to calculate the fill time and the overall capillary impregnation dynamics for any arbitrary cylindrical sample made of aligned micro-cylinders, by taking into account the role of the trapped gas, which opposes and slows down the inward capillary flow.     

Whirling of a forced cantilevered beam with static deflection. I: Primary resonance

The response of a slender, clastic, cantilevered beam to a transverse, vertical, harmonic excitation is investigated. The effects of nonlinear curvature, nonlinear inertia, viscous damping and static load are included. Previous work often has neglected the static deflection caused by the weight of the beam, which adds quadratic terms in the governing equations of motion. Galerkin's method is used with three modes and approximate solutions of the temporal equations are obtained by the method of multiple scales. Primary resonance is treated here, and out-of-plane motion is possible in the first and second modes when the principal moments of inertia of the beam cross-section are approximately equal. In Parts II and III, secondary resonances and nonstationary passages through various resonances are considered.     

STUDY FOR THE BIFURCATION TOPOLOGICAL STRUCTURE AND THE GLOBAL COMPLICATED CHARACTER OF A KIND OF NONLINEAR FINANCE SYSTEM(Ⅱ)

Based on the work discussed on the former study, this article first starts from the mathematical model of a kind of complicated financial system, and analyses all possible things that the model shows in the operation of our country’s macro-financial system: balance, stable periodic, fractal, Hopf-bifurcation, the relationship between parameters and Hopf-bifurcation, and chaotic motion etc. By the changes of parameters of all economic meanings, the conditions on which the complicated behaviors occur in such a financial system, and the influence of the adjustment of the macro-economic policies and adjustment of some parameter on the whole financial system behavior have been analyzed. This study will deepen people’s understanding of the lever function of all kinds of financial policies.     

Nonlinear flexural-flexural-torsional interactions in beams including the effect of torsional dynamics. I: Primary resonance

Nonlinear coupling between torsional and both in-plane and out-of-plane flexural motion is examined for inextensional beams (or beam-like structures) whose torsional and flexural eigenfrequencies are of the same order. The analysis presented here is based on a consistent set of nonlinear differential equations which contain both curvature and inertia nonlinearities, and account for torsional dynamics. Response characteristics, including stability, are determined for cantilever beams subjected to a lateral periodic excitation. The beam's response in the presence of a one-to-one internal resonance involving a torsional frequency and an in-plane bending frequency is investigated in detail.     

Nonlinear flexural-flexural-torsional interactions in beams including the effect of torsional dynamics. II: Combination resonance

In Part I of this work nonlinear coupling between torsional motion and both in-plane and out-of-plane flexural motion was examined for inextensional beams in the presence of a one-to-one internal resonance. Here the nonlinear response of the system considered in Part I is investigated for the case of an internal combination resonance involving modes associated with bending in two directions and torsion. The analysis presented is based on a consistent set of nonlinear differential equations which contain both curvature and inertia nonlinearities and account for torsional dynamics.     

Stability and Bifurcation Analysis of a Modified Geometrically Nonlinear Orthotropic Jeffcott Model with Internal Damping

In this paper, a modified Jeffcott model is proposed and studied in order to shed light into the dynamics of a complex system, the Short Electrodynamic Tether (SET), which is similar to an unbalanced rotor. Due to the internal damping, a geometrically linear SET model appears to be unstable as predicted by the linear rotordynamics theory. Some studies in the field of rotordynamics suggest that this instability caused by internal damping do not appear if geometric nonlinearities are taken into account in the system equations of motion. Stability and bifurcation analysis have been carried out on the modified Jeffcott model, which accounts for geometric nonlinearities, orthotropy in the shaft's cross section, and a viscous damping-based internal damping model. The stability results analytically obtained have been compared with a nonlinear multibody model by means of time simulations and good agreement has been found.     

Mathematical Modeling and Parameter Identification of a Planar Servo-Pneumatic Test Facility. Part II: Experimental Identification

The main objective of this paper is the identification of the inertia parameters of a rigid body under planar motion using a planar servo-pneumatic test facility designed for vibration tests. The hardware realization of the test facility used is discussed. The pneumatic components as well as the mechanical components of the test facility are described by linear and by nonlinear mathematical models, derived in Part I [1] of this paper. These model equations are used as identification hypotheses in the identification process. A comparison of time histories obtained by computer simulations of the nonlinear test facility model and by laboratory experiments shows that this nonlinear test facility model provides a realistic identification hypothesis for the estimation experiments. Based on different model hypotheses the inertia parameters of the test table and of the payload have been successfully identified from laboratory experiments. The relative estimation errors of the identified parameters are less than 10%.     

Nonlinear Dynamics of a Rigid Unbalanced Rotor in Journal Bearings. Part I: Theoretical Analysis

The dynamic behaviour of a rigid rotor supported on plain journal bearings was studied, focusing particular attention on its nonlinear aspects. Under the hypothesis that the motion of the rotor mass center is plane, the rotor has five Lagrangian co-ordinates which are represented by the co-ordinates of the mass center and the three angular co-ordinates needed to express the rotor's rotation with respect to its center of mass. In such conditions, the system is characterised not only by the nonlinearity of the bearings but also by the nonlinearity due to the trigonometric functions of the three assigned angular co-ordinates. However, if two angular co-ordinates have values that are generally quite small because of the small radial clearances in the bearings, the system is de facto linear in these angular co-ordinates. Moreover, if the third angular co-ordinate is assumed to be cyclic [18], the number of degrees of freedom in the system is reduced to four and nonlinearity depends solely on the presence of the journal bearings, whose reactions were predicted with the -film, short bearing model. After writing the equations of motion in this way and determining a numerical routine for a Runge–Kutta integration the most significant aspects of the dynamics of a symmetrical rotor were studied, in the presence of either pure static or pure couple unbalance and also when both types of unbalance were present. Two categories of rotors, whose motion is prevailingly a cylindrical whirl or a conical whirl, were put under investigation.     

Effect of dentin tubules to the mechanical properties of dentin. Part II: Experimental study

To verify the theoretical models of varying transversely isotropic stress-strain relations of dentin established in the preceding work (Part I), we perform a set of experiments. Because of the very fine tooth size, it usually seems to be difficult to directly measure the inhomogeneous and anisotropic parameters of dentin. In this paper, by the digital speckle correlation method, tensile experiments are made on the small dentin samples either parallel or perpendicular to the dentin tubules. With the theoretically predicted elastic stress-strain relations, an optimization method is proposed to fit the strain curve adapted to the experimental data. The results show that the theoretical elastic stress-strain relations coincides very well with the experimental observations. The determined Young's modulus and Poisson's ratio of dentin matrix are 29.5 GPa and 0.44, respectively, in the optimization sense. The project supported by the National Natural Science Foundation of China (19525207)     

Dynamics of a Rigid Unbalanced Rotor with Nonlinear Elastic Restoring Forces. Part I: Theoretical Analysis

In a previous paper, the dynamic behaviour of a Jeffcott rotor was studied in the presence of pure static unbalance and nonlinear elastic restoring forces. The present paper extends the analysis to a rigid rotor with an axial length such as to make the transverse moment of inertia greater than the axial one. As in the previous investigation, the elastic restoring forces are assumed to be nonlinear and the effects of couple unbalance are also included but, unlike the Jeffcott rotor, the system exhibits six degrees-of-freedom. The Lagrangian coordinates were fixed so as to coincide with the three coordinates of the centre of mass of the rotor and the three angular coordinates needed in order to express the rotor's rotations with respect to a reference frame having its origin in the centre of mass. The precession motions of such a rotor turn out to be cylindrical at low angular speeds and exhibit a conical aspect when operating at higher speeds. The motion equations of the rotor were written with reference to a system that was subsequently adopted for the experimental analysis. The particular feature of this system was the use of a steel wire (piano wire) for the rotor shaft, suitably constrained and with the possibility of regulating the tension of the wire itself, in order to increase or reduce the nonlinear character of the system. The numerical analysis performed with integration of the motion equations made it possible to point out that chaotic solutions were manifested only when the tension in the wire was given the lowest values – i.e. when the system was strongly nonlinear – in the presence of considerable damping and rotor unbalance values that were so high as to lose any practical significance. Under conditions commonly shared by analogous real systems characterised by poor damping, where the contribution to nonlinearity is almost entirely due to elastic restoring forces, the analysis pointed out that precession motions may be manifested with a periodic character, whether synchronous or not, or a quasi-periodic character, but in no case is the solution chaotic.     

Analysis of Wet Pressing of Paper: The Three-Phase Model. Part II: Compressible Air Case

In this study we consider a model of wet pressing of paper. We use the techniques and results from the first part of this paper, where a simplified model is studied in details. The model is, using suitable transformation, rewritten in the standard parabolic-hyperbolic form. Numerical solution for typical example is given and the effects of plastic deformations of paper are investigated. Finally, the model is employed to adres the problem of choosing an optimal pressing regime.     

Analysis of wet pressing of paper: the three-phase model. Part I: constant air density

In this study, we consider a one-dimensional three-phase model describing wet pressing of paper. Part I is devoted to the simplified case in which air is assumed incompressible. In Part II we drop this assumption. The model is formulated in terms of water saturation and void ratio and it uses a material coordinate to describe spatial dependence. It also involves cross or matching conditions between the wet paper and the felt. In mathematical terms, we end up with a coupled system of equations: a nonlinear diffusion equation and a first order hyperbolic equation. We present some analytical observations to explain the essential behaviour of the model and we carry out numerical experiments using an upwind and a front tracking method.     

Slip-line modeling of machining with a rounded-edge tool—Part II: analysis of the size effect and the shear strain-rate

Part II of the present study quantitatively analyzes orthogonal metal cutting processes based on the new slip-line model proposed in Part I. The applicable range of the model is illustrated, followed by an explanation of the non-unique nature of the model. It is suggested that the tool edge roundness be comprehensively defined by four variables. Namely: tool edge radius, position of the stagnation point on the tool edge, tool-chip frictional shear stress above the stagnation point on the tool edge, and tool-chip frictional shear stress below the stagnation point on the tool edge. The effects of these four variables on eight groups of machining parameters are investigated. These include (1) cutting force, thrust force, resultant force, and the ratio of cutting force to thrust force; (2) ploughing force; (3) chip up-curl radius; (4) chip thickness; (5) tool-chip contact length; (6) thickness of the primary shear zone; (7) average shear strain in the primary shear zone; and (8) average shear strain-rate in the primary shear zone. The importance of tool edge roundness is further reinforced by a series of new research findings made in this paper. It is revealed that the size effect highly depends on the material constitutive behavior in machining. The dependence of the thickness of the primary shear zone and the dependence of the magnitude of shear strain-rate in the primary shear zone on the tool edge radius are well demonstrated. A surprisingly good agreement between theory and experiments is reached.