Simulation of impacts in geartrains using different approaches

Gear hammering in diesel engines is a well-known phenomenon in geared drives, exhibiting not only noise but also influencing the performance and durability of diesel engines. Gear hammering is characterised by flanks in contact that lift off and cause impacts when the contact reestablishes, which induces high, sharp dynamic loads. The knowledge of these contact forces is very important for the design of gears. Since contact forces in meshing gears are extremely difficult and expensive to measure, the simulation of these forces plays an important role. Nowadays, these contact simulations are usually carried out within overall models of entire engines using commercial multibody programs that provide submodels for gear contacts, usually based on rigid-body models. However, to reduce inertia effects, gears in geartrains are often designed with very thin bodies, whose elastic compliance influences the contact behaviour to a large extent. For a closer insight into the dynamic behaviour, and especially the influence of thin gear bodies during impact, a typical gear pairing is selected and impacts between one tooth pair are investigated for different boundary and initial conditions with three different models. Besides a multibody model, similar to those used in commercial multibody programs, a fully nonlinear finite-element model and a modally reduced model in combination with a local force law is used. The results of the different approaches are benchmarked in terms of accuracy and numerical effort.     

Errata: Analytical Treatment of Some Extended Problems in Structural Optimization

ABSTRACT

The recursive Newton-Euler dynamic formulation is used to derive the equations of motion of a manipulator with harmonic drives. The derivation is general, in that the harmonic drive is viewed as a separate body that forms a kinematically closed chain with two contiguous links, leading to a comprehensive dynamic model. The harmonic drive is modeled as a flexible and rigid gear with a high gear reduction ratio. Under different modeling assumptions, the effects of gear flexibility and dynamic coupling are examined using a seven-degree-of-freedom manipulator.     

Dynamic characteristic analysis of spur gear system considering tooth contact state caused by shaft misalignment

The effect of gear contact state change due to shaft misalignment on meshing stiffness is usually neglected in the traditional stiffness calculation model with misalignment error, the further influence mechanism of shaft misalignment on gear dynamic characteristics is also unclear. To address these shortcomings, a new mesh stiffness calculation model with misaligned gear considering the effects of tooth contact state is proposed by combining the improved loaded tooth contact analysis (LTCA) model. Then the effects of tooth contact state changes aroused by shaft misalignment on the meshing stiffness excitation are investigated. Moreover, a dynamic model of the misaligned gear system with 8 degrees of freedom (DOF) is established, and based on which the dynamic characteristics of the gear system are investigated and verified by experiment. The study results indicate that the proposed model can be used to evaluate the stiffness excitation and dynamic characteristics of the misaligned gear system with the tooth contact state taken into consideration. This study can provide a theoretical method for evaluating and identifying shaft misalignment errors.

     

斜齿轮弹流润滑下的接触疲劳寿命计算

经典齿轮接触疲劳强度理论是基于光滑表面赫兹干接触理论,而实际齿面具有粗糙度,且啮合轮齿多数处于混合润滑状态.本文基于齿轮润滑接触分析建立了渐开线斜齿轮的接触疲劳寿命计算模型.模型由齿轮润滑接触分析模型和基于次表面应力分布的疲劳寿命模型组成.首先将斜齿圆柱齿轮一对齿的瞬时啮合等效为两反向圆锥的接触问题,建立了齿轮的有限长弹流润滑计算模型,考虑了齿轮啮合周期内瞬时载荷、接触线长、卷吸速度等因素的影响,基于统一雷诺方程方法求得啮合齿对间的润滑压力和油膜厚度分布;在此基础上,计算轮齿接触区次表面的米歇斯应力分布,根据Zaretsky接触疲劳寿命计算模型,对齿轮组的接触疲劳寿命进行模拟预测.针对不同工况参数下接触疲劳寿命计算表明:润滑油黏度、轮齿表面粗糙度等因素对齿面接触疲劳寿命均有显著的影响.     

Local contact characteristics of threaded surfaces in a planetary roller screw mechanism

Abstract

This study investigates the local contact characteristics of the threaded surface meshing of a planetary roller screw mechanism (PRSM). First, according to the threaded surface structure and threaded surface meshing characteristics, expressions for the principal curvature and principal direction of the contact ellipse at a contact point are derived based on the differential geometry theory. Next, based on a force analysis and threaded surface equations, an analytical model is established to calculate the dimensions and principal vector direction of contact ellipses on threaded surfaces. The elastic deformation and maximum contact stress are determined using Hertz elastic contact theory. Then, finite element (FE) numerical models for a single pair of threads at the screw–roller interface and the roller–nut interface are developed to calculate the contact area and maximum contact stress. The results are compared with those of the analytical model to demonstrate the validity of the analytical model. Finally, based on the analytical model proposed in this article, the local contact characteristics of threaded surfaces with various thread pitches, flank angles, and profile radii of roller threads are analyzed in detail.     

Prediction of Gear Dynamics Using Fast Fourier Transform of Static Transmission Error*

ABSTRACT

An analytical computer simulation procedure for dynamic modeling of low-contact-ratio spur gear systems is presented. The procedure computes the gear static transmission error and uses a Fast Fourier Transform (FFT) to generate its frequency spectrum at various tooth profile modifications. The dynamic loading response of an unmodified (perfect involut) gear pair is compared with that of gears with profile modifications. Correlations are found between several profile modifications and the resulting dynamic loads. An effective error, obtained from frequency domain anal     

Projectile Impact on a Thin. Flexible Structure: A Singular Dynamic Contact Phenomenon

ABSTRACT

In this paper we demonstrate an unexpected type of dynamic contact phenomenon which arises when a large object impacts a thin flexible structure. It is shown that the contact pressure distribution is singular at the edges of the contact region when the region is expanding with a speed which is higher than the wave speed in the structure. This type of phenomenon will occur in a number of structural collision problems in which one of the objects such as a cable or a thin plate is much more flexible than the other. Head injury problems represent a typical example

The solution for a very simple model of such a system, namely that of a rigid cylindrical impaclor striking an infinitely long string, is given in detail to illustrate the phenomenon.     

Formulating Three-Dimensional Contact Dynamics Problems

ABSTRACT

Complementarity formulations are a promising approach for solving dynamic multi-rigid-body contact problems. Two aspects of simulating contact in a complementarity setting are addressed here. First, an explicit formulation of the differential equations governing contact points for bodies of general surface geometry is developed. These equations may be used to integrate the contact position and to set up the basic dynamics equations. Second, an efficient method for handling frictionless planar contacts of arbitrary boundary shape is presented. Throughout, the problem is set up as explicitly as possible, with special attention being given to the way that the contact geometry is related to the dynamics.     

A Robust Finite Element-based Filter for Digital Image and Volume Correlation Displacement Data

Background

Digital Image and Volume Correlation (DIC and DVC) are non-contact measurement techniques that are used during mechanical testing for quantitative mapping of full-field displacements. The relatively high noise floor of DIC and DVC, which is exasperated when differentiated to obtain strain fields, often requires some form of filtering. Techniques such as median filters or least-squares fitting perform poorly over high displacement gradients, such as the strain localisation near a crack tip, discontinuities across crack flanks or large pores. As such, filtering does not always effectively remove outliers in the displacement field.

Objective

This work proposes a robust finite element-based filter that detects and replaces outliers in the displacement data using a finite element method-based approximation.

Methods

A method is formulated for surface (2D and Stereo DIC) and volumetric (DVC) measurements. Its validity is demonstrated using analytical and experimental displacement data around cracks, obtained from surface and full volume measurements.

Results

It is shown that the displacement data can be filtered in such a way that outliers are identified and replaced. Moreover, data can be smoothed whilst maintaining the nature of the underlying displacement field such as steep displacement gradients or discontinuities.

Conclusions

The method can be used as a post-processing tool for DIC and DVC data and will support the use of the finite element method as an experimental–numerical technique.

     

Buckling and postbuckling of concentric cylindrical tubes under external pressure

The problem considered involves a structure composed of two concentric and bonded tubes subjected to external and uniform pressure. Compression tests are conducted using structures formed by a thin-walled internal rubber tube and a thick-walled external foam tube. Experimental results are plotted under the form of a bifurcation diagram representing the inner cross-sectional area of the thin tube as a function of pressure. The buckling pressure P_b and the contact pressure P_co are determined from this non linear diagram. A numerical computation by the Finite Element Method (FEM) is used in order to calculate the Euler buckling pressure P_b and the results are compared with experimental data. It is shown that the buckling pressure and the associated buckling mode n, strongly depend upon the elastic and geometrical parameters of both the tubes. The experimental and numerical investigations are also extended to postbuckling behaviour. The contact between the opposite sides of the inner wall is occured with a buckling mode index n = 2, 3. This contact phenomenon is given rise to the discontinuity of a previous diagram and was characterized by the contact pressure P_co.     

Modeling and analyzing of torsional dynamics for helical gear pair considered double and three teeth drive-side meshing

Helical gears are generally considered to be more stable than spur gears. But rattling of the helical gear transmission is found in the engineering practice. The torsional dynamics equations of helical gear pair in high-speed railway gearbox are established in order to reveal the rattling mechanism of helical gear transmission. Double and three teeth pair drive-side meshing are considered. The multi-state meshing zone, load distribution rate and time-varying stiffness determined by contact ratio are analyzed and calculated. The dynamic characteristic transition process of the system is analyzed according to the bifurcation diagrams and the corresponding top Lyapunov exponent (TLE) diagrams, phase portraits, Poincaré maps and time history spectrums of dynamic meshing force based on the calculation of these parameters. The tooth disengagement, tooth back-side contact and their parameter range are found. This study can provide theoretical basis for rattling suppression and transmission stability improvement of helical gear pair.

     

基于分形理论的双渐开线齿轮接触应力研究

综合考虑接触面粗糙度、材料特性等因素对齿轮接触应力的影响,基于分形理论和经典Hertz接触理论建立双渐开线齿轮分形接触模型. 该模型中,影响载荷和实际接触面积的主要因素包括分形维数、粗糙度幅值和材料特性参数. 理论分析表明:分形维数一定时,真实接触面积随着载荷的增大而增大;载荷一定时,接触面积随着粗糙度幅值的增大而减小;随着材料特性参数值的增加,在一定程度上加强了软材料轮齿承载能力,同时会使得微凸体由弹性变形到塑性变形的临界面积减小. 对比分形接触模型和有限元模型两种计算双渐开线齿轮轮齿接触应力方法,结果证明了分形接触模型计算双渐开线齿轮接触应力的有效性.      

表面粗糙度特征对齿轮接触区润滑特性的影响

大部分工程实际粗糙表面符合非高斯分布,并对齿轮接触副润滑特性有重要影响.将渐开线齿轮啮合过程中齿面接触等效为三维无限长线接触,建立了一个可分析直齿轮和斜齿轮的混合弹流润滑计算模型;采用基于快速傅里叶变换的数值仿真方法生成给定参数的非高斯粗糙表面;运用该模型对直齿轮和斜齿轮啮合过程进行分析,求得不同表面粗糙度特征齿轮在各个啮合点的油膜厚度、接触区载荷以及接触区比例的情况.结果表明:对于标准差相等的非高斯粗糙表面,偏度值对齿轮润滑状况的影响与工况紧密相关,在润滑良好的条件下,偏度值越小润滑状况越优;润滑恶劣的条件下,偏度值越大润滑状况越优;而在各种工况下,峰度值对齿轮润滑状况的影响都表现出峰度值越大润滑状况越优的特点.     

A Balanced Maximum Fillet Stresses on Normal Contact Ratio Spur Gears to Improve the Load Carrying Capacity Through Nonstandard Gears

This article presents an idea to remove the inequality in maximum fillet stresses developed between pinion and gear of a step up gear drive. This uniform fillet strength of the gear drive can be achieved by using nonstandard pinion and gear with appropriate addendum modifications generated by nonstandard basic racks of respective tooth thickness not equal to 0.5πm at the pitch circle. The influence of gear parameters such as gear ratio, pressure angle, addendum factor, pinion teeth number, and addendum modifications on the maximum fillet stress on the nonstandard pinion and gears of different tooth thickness has been analyzed through finite element method and finally the optimum value of rack tooth thickness coefficients (k _pc and k _gc ) are suggested for the given gear drive (defined by i) that improves the fillet capacity in bending. This study has been extended for various drives like S _std , S _o , S ₊, and S _? drives.     

齿向修形对滤波减速器润滑性能的影响分析

综合考虑了滤波减速器齿向修形参数、真实齿面粗糙度和瞬态效应等因素,建立了轮齿混合润滑数学模型,数值计算了不同修形参数值对应不同啮合点的最大压力和中心膜厚,分析了齿面粗糙度和转速对润滑性能的影响.结果表明:修形参数r和Ry均存在一个优化范围,使得轮齿表面最大油膜压力显著降低,边缘效应弱化,而中心膜厚则随着r和Ry的增大而逐渐增大;未修形轮齿边缘油膜压力受粗糙度的影响而急剧增大,边缘效应更加显著,修形后轮齿的边缘效应得到了明显改善,因此,轮齿修形也因粗糙表面的存在而显得更加重要;随着转速逐渐降低,轮齿表面的平均油膜厚度逐渐变小,接触比逐渐增大,轮齿表面由弹流润滑逐渐转为混合润滑,最后演变为边界润滑.     

Hammering in diesel-engine driveline systems

The gears of driveline systems in diesel engines must be designed with large backlashes within the gear meshes due to the large temperature operating range of such systems. This leads to hammering processes with extremely high overloads where hammering is an impulsive separation process of the tooth flanks caused by the large torques as generated by the injection pumps. This paper presents a theoretical model for such processes and gives a comparison with measurements.     

The effect of concrete slab–rockfill interface behavior on the earthquake performance of a CFR dam

Earthquake response of the concrete slab is mostly depended upon its conjunction with rockfill. This study aims to reveal the effect of concrete slab–rockfill interface behavior on the earthquake performance of a concrete-faced rockfill dam considering friction contact and welded contact. Friction contact is provided by using interface elements with five numbers of shear stiffness values. 2D finite element model of Torul concrete-faced rockfill dam is used for this purpose. Linear and materially non-linear time-history analyses considering dam–reservoir interaction are performed using ANSYS. Reservoir water is modeled using fluid finite elements by the Lagrangian approach. The Drucker–Prager model is preferred for concrete slab and rockfill in non-linear analyses. Horizontal component of 1992 Erzincan earthquake with peak ground acceleration of 0.515g is used in analyses. The maximum and minimum displacements and principal stresses are shown by the height of the concrete slab and earthquake performance of the dam is investigated considering different joint conditions for empty and full reservoir cases. In addition, potential damage situations of concrete slab are evaluated.     

齿轮接触有限元分析

通过接触仿真分析研究了通用接触单元在轮齿变形和接触应力计算中的应用。建立了一对齿轮接触仿真分析的模型，并使用新的接触单元法计算了轮齿变形和接触应力，与赫兹理论比较，同时也计算了摩擦力对接触应力的影响。计算分析了单元离散、几何、边界范围与加载或约束处理方式的误差，建立了一个计算轮齿变形和接触应力的标准，说明了新的接触单元法的精确法、有效性和可靠性。     

基于载荷分担理论的渐开线斜齿轮热混合弹流润滑分析

沿接触线把斜齿轮分成许多小薄片,每一薄片看成具有当量角速度的直齿轮,根据欧拉方程得到任一接触点处的曲率半径和表面速度.然后基于载荷分担、弹流润滑和粗糙线接触理论,建立了考虑表面粗糙度的斜齿轮传动混合热弹流润滑模型.研究了斜齿轮传动稳态载荷分布下牛顿流体和Carreau流体时的润滑特性.结果表明:牛顿流体和Carreau非牛顿流体模型下,中心油膜厚度、油膜承载比例、油膜温升随时间和接触线的变化规律相同.牛顿流体下的摩擦系数较工程实际偏大.Carreau非牛顿流体模型下摩擦系数和工程实际相符,其随接触线啮合位置的变化规律与油膜厚度正好相反.