Preparation, structure, and properties of styrene-ethylene-butylene-styrene block copolymer/clay nanocomposites: Part II fracture behaviors

Styrene-ethylene-butylene-styrene block copolymer (SEBS)/clay nanocomposites were prepared via a melt mixing technique. Various amounts of two types of maleated compatibilizers, styrene-ethylene-butylene-styrene block copolymer grafted maleic anhydride (SEBS-g-MA) and polypropylene grafted maleic anhydride (PP-g-MA), were incorporated to improve the dispersion of commercial organoclay (denoted as 20A), respectively. PP-g-MA compatibilized system conferred higher tensile strength and tear strength (initiation condition) than SEBS-g-MA compatibilized system. At a fixed content of compatibilizers, the above mechanical properties were improved with increasing clay content as well. By relating tensile strength to tear strength (arrest condition), the average depth of flaw was in the range of 33.8 ± 3.4 μm, which successfully confirmed the extension of Rivlin and Thomas’s theory for conventional elastomers to thermoplastic elastomer/clay nanocomposites for the first time. Cutting strength of SEBS/clay nanocomposites gave an intermediate value when compared with crystalline plastics and conventional amorphous elastomers, which further signified the importance of micro-yielding of styrene domains, crystalline yielding of compatibilizer, and filler reinforcement even in the nano-fracture zone of deformation.     

Reactively and physically compatibilized immiscible polymer blends: stability of the copolymer at the interface

This paper reports on the interfacial behaviour of block and graft copolymers used as compatibilizers in immiscible polymer blends. A limited residence time of the copolymer at the interface has been shown in both reactive blending and blend compatibilization by preformed copolymers. Polystyrene (PS)/polyamide6 (PA6), polyphenylene oxide (PPO)/PA6 and polymethylmethacrylate (PMMA)/PA6 blends have been reactively compatibilized by a styrene-maleic anhydride copolymer SMA. The extent of miscibility of SMA with PS, PPO and PMMA is a key criterion for the stability of the graft copolymer at the interface. For the first 10 to 15 minutes of mixing, the in situ formed copolymer is able to decrease the particle size of the dispersed phase and to prevent it from coalescencing. However, upon increasing mixing time, the copolymer leaves the interface which results in phase coalescence. In PS/LDPE blends compatibilized by preformed PS/hydrogenated polybutadiene (hPB) block copolymers, a tapered diblock stabilizes efficiently a co-continuous two-phase morphology, in contrast to a triblock copolymer that was unable to prevent phase coarsening during annealing at 180°C for 150 minutes.     

Influence of SEBS-g-MA on morphology, mechanical, and thermal properties of PA6/PP/organoclay nanocomposites

Polyamide 6/polypropylene (PA6/PP = 70/30 parts) blends containing 4 phr (parts per hundred resin) of organically modified clay (organoclay) toughened with maleated styrene-ethylene-butylene-styrene (SEBS-g-MA) were prepared by melt compounding using co-rotating twin-screw extruder followed by injection molding. X-ray diffraction (XRD) and transmission electron microscope (TEM) were used to characterize the structure of the nanocomposites. The mechanical properties of the nanocomposites were determined by tensile, flexural, and notched Izod impact tests. The single edge notch three point bending test was used to evaluate the fracture toughness of SEBS-g-MA toughened PA6/PP nanocomposites. Thermal properties were studied by using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). XRD and TEM results indicated the formation of the exfoliated structure for the PA6/PP/organoclay nanocomposites with and without SEBS-g-MA. With the exception of stiffness and strength, the addition of SEBS-g-MA into the PA6/PP/organoclay nanocomposites increased ductility, impact strength and fracture toughness. The elongation at break and fracture toughness of PA6/PP blends and nanocomposites were increased with increasing the testing speed, whereas tensile strength was decreased. The increase in ductility and fracture toughness at high testing speed could be attributed to the thermal blunting mechanism in front of crack tip. DSC results revealed that the presence of SEBS-g-MA had negligible effect on the melting and crystallization behavior of the PA6/PP/organoclay nanocomposites. TGA results showed that the incorporation of SEBS-g-MA increased the thermal stability of the nanocomposite.     

Highly toughened poly(lactic acid) (PLA) prepared through melt blending with ethylene-co-vinyl acetate (EVA) copolymer and simultaneous addition of hydrophilic silica nanoparticles and block copolymer compatibilizer

In this study, a highly toughened PLA was prepared through physical melt-blending with EVA at the presence of hydrophilic nanosilica and SEBS-g-MA block copolymer compatibilizer. The effect of nanosilica and compatibilizer on the morphology, mechanical properties, and linear rheology of the PLA/EVA blends was also investigated. According to TEM images, nanosilica was selectively located in the PLA matrix while some were placed on the interface between the two polymers as was also predicted by thermodynamic and kinetic analysis. Upon the addition of nanoparticles, the interfacial adhesion between the phases was enhanced and the average droplet size decreased. Interestingly, incorporation of SEBS-g-MA induced morphological changes as the spherical EVA droplets turned into a cylindrical shape. DSC results indicated that blending with EVA copolymer resulted in the reduction of crystallization of PLA matrix; however, the crystallinity increased at the presence of nanoparticles up to 5 wt%. The addition of compatibilizer considerably hindered the crystallization of the PLA phase. PLA/EVA blend containing optimum levels of nanosilica exhibited considerably enhanced tensile toughness, elongation at break, and impact strength. On the other hand, the simultaneous addition of nanoparticles and SEBS-g-MA led to synergistic toughening effects and the compatibilized blend containing nanosilica exhibited excellent impact toughness. For instance, the elongation at break of the compatibilized PLA/EVA blend containing the optimal content of nanosilica was increased from 7% to 121% (compared to neat sample). The notched Izod impact strength was also increased from 5.1 to 65 kJ/m². Finally, the microstructure of the blends was assessed by rheological measurements.     

Crystallization of polyamide confined in sub‐micrometer droplets dispersed in a molten polyethylene matrix

The crystallization of submicrometer PA6 droplets dispersed in an ethylene‐1‐octene copolymer matrix, using PE‐g‐MA as a compatibilizer agent, is investigated. This system shows a nonconventional mechanical behavior at high temperatures. Up to ～100 °C above the final melting temperature of the ethylene‐1‐octene copolymer matrix, the system shows good thermal and mechanical properties including dimensional stability. Because of the dispersed phase morphology of the system, so‐called fractionated/homogeneous crystallization takes place leading to an extra supercooling of PA6: ～50 °C compared to the bulk PA6 crystallization temperature. Thus—though this is most probably just of interest for small‐scale research—the system can be processed at lowered temperatures while still providing exceptional high‐temperature properties. While the matrix is in the melt state when crystallization of the dispersed PA6 phase occurs, the possibility of matrix induced crystallization is absent, contrary to almost all of the ‘dispersed droplets in a matrix’ systems reported so far. The kinetics of this phenomenon is investigated in detail by DSC: the existence of fractionated/homogeneous crystallization is shown to be related to the lack of active nuclei in the dispersed droplets by means of self‐seeding experiments. The occurrence of extensive cold crystallization of PA6 in the confined environment is studied as is the crystallization kinetics, including the characterization of its time dependences showing its sporadic nature. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 815–825, 2006     

Preparation, structure, and properties of styrene-ethylene-butylene-styrene block copolymer/clay nanocomposites: Part III. Effectiveness of compatibilizers

Styrene-ethylene-butylene-styrene block copolymer (SEBS)/clay nanocomposites were prepared via a melt mixing technique. Various amounts of two types of compatibilizers, maleated styrene-ethylene-butylene-styrene block copolymer (SEBS-g-MA) and maleated polypropylene (PP-g-MA), were incorporated to improve the dispersion of 5 wt% commercial organoclay (denoted as 20A), respectively. The X-ray diffraction (XRD) and transmission electron microscope (TEM) experimental results revealed that nanocomposites were achieved in all cases. The Fourier Transform infrared spectra and dynamic properties indicated a higher interaction for styrene blocks with clay moiety. The transmittance for the nanocomposites slightly decreased with increasing SEBS-g-MA dosage, which presented an opposing trend compared with the PP-g-MA case. The PP-g-MA compatibilized system conferred higher mechanical properties than the SEBS-g-MA compatibilized system, even though a higher dosage of SEBS-g-MA was beneficial in further expanding the interlayer spacing of the clay. The unexpected results suggested matrix properties and interfacial phase were the major factors in attaining the best performance in terms of mechanical properties for the investigated system.     

Structure and properties of compatibilized recycled poly(ethylene terephthalate)/linear low density polyethylene blends

Blends of recycled poly(ethylene terephthalate) (R-PET) and linear low density polyethylene (LLDPE) were compatibilized with poly(styrene-ethylene/butyldiene-styrene) (SEBS) and maleic anhydride-grafted poly(styrene-ethylene/butyldiene-styrene) (SEBS-g-MA). Effects of compatilizer were evaluated systematically by study of mechanical, thermal and morphology properties together with crystallization behavior of PET. Tensile properties of the blends were improved effectively by the addition of 10 wt% SEBS-g-MA, elongation at break and charpy impact strength were increased with the increasing content of compatilizer. SEBS-g-MA is more effectual on mechanical properties of R-PET/LLDPE blends than SEBS. DSC analysis illustrates crystallinities of PET and LLDPE were increased by compatilizer at annealing condition. WAXD and FT-IR spectra show that annealing influences crystallization behavior of PET. Different compatilizer content results in different morphology structure, in particular, higher SEBS-g-MA content can induce the formation of a salami microstructure.     

Morphology and thermal properties of a PC/PE blend with reactive compatibilization

Reactive compatibilization of immiscible polymers is becoming increasingly important and hence a representative study of a polycarbonate/high density polyethylene (PC/HDPE) system is the focus of this paper. A grafted copolymer PC‐graft‐ethylene‐co‐acrylic acid (PC‐graft‐EAA) was generated as a compatibilizer in situ during processing operation by ester and acid reaction between PC and ethylene‐acrylic acid (EAA) in the presence of the catalyst dibutyl tin oxide (DBTO). As the polyethylene (PE) matrix does not play any part during the synthesis of the copolymer and since PC and EAA are also immiscible, to simplify the system, the influence of this copolymer formation at the interface between PC and EAA on rheological properties, phase morphology, and crystallization behavior for EAA/PC binary blends was first studied. The equilibrium torque increased with the DBTO content increasing in EAA/PC blends on Haake torque rheometer, indicating the in situ formation of the graft copolymer. Scanning electron microscopy (SEM) studies of cryogenically fractured surfaces showed a significant change at the distribution and dispersion of the dispersed phase in the presence of DBTO, compared with the EAA/PC blend without the catalyst. Differential scanning calorimetry (DSC) studies suggested that the heat of fusion of the EAA phase in PC/EAA blends with or without DBTO reduced with the formation of the copolymer compared with pure EAA. Then morphological studies and crystallization behavior of the uncompatibilized and compatibilized blends of PC/PE were studied as functions of EAA phase concentration and DBTO content. Morphological observations in PC/PE blends also revealed that on increasing the EAA content or adding the catalyst DBTO, the number of microvoids was reduced and the interface was intensive as compared to the uncompatibilized PC/PE blends. Crystallization studies indicated that PE crystallized at its bulk crystallization temperature. The degree of crystallinity of PE phase in PC/PE/EAA blends was also reduced with the addition of EAA and DBTO compared to the uncompatibilized blends of PC/PE, indicating the decrease in the degree of crystallinity was more in the presence of PC‐graft‐EAA. Copyright © 2007 John Wiley & Sons, Ltd.     

剪切作用下马来酸酐接枝乙烯-辛烯共聚物和乙烯-丙烯酸丁酯-甲基丙烯酸缩水甘油酯共聚物对PA1010/PP共混物的增容作用比较

采用熔体共混的方法制备了两种增容剂增容的聚酰胺1010/聚丙烯(PA1010/PP)共混物,通过扫描电镜(SEM)、力学性能和差示扫描量热(DSC)测试,对动态保压注射成型(动态)和普通注射成型(静态)中增容剂POE-g-MAH(马来酸酐接枝乙烯-辛烯共聚物)和PTW(乙烯-丙烯酸丁酯-甲基丙烯酸缩水甘油酯共聚物)对PA1010/PP共混物的增容作用进行了比较研究.研究结果表明,普通注射成型中,PTW增容体系具有更小的分散相粒子,在DSC测试中出现两个结晶峰,即出现异相成核结晶和均相成核结晶,具有更好的拉伸和冲击性能,增容作用更佳.动态保压注射成型中施加剪切可以提高所有共混物的拉伸强度、拉伸模量和缺口冲击强度,PTW和POE-g-MAH两种增容剂增容体系冲击性能相近,但POE-g-MAH增容体系的分散相相区尺寸减小明显、分布均匀性显著增加,材料冲击强度增加幅度更大,表明剪切更有利于POE-g-MAH增容作用的进行.两种增容剂增容作用的不同源于它们化学组成的不同引起的材料形态差别.     

Effect of maleic anhydride-grafted ethylene-propylene rubber on the mechanical, rheological and morphological properties of organoclay reinforced polyamide 6/polypropylene nanocomposites

Polyamide 6/polypropylene (PA6/PP = 70/30 parts) blends containing 4 phr (parts per hundred resin) of organophilic modified montmorillonite (organoclay) were compatibilized with maleic anhydride-grafted ethylene-propylene rubber (EPRgMA). The blends were melt compounded in twin screw extruder followed by injection molding. The mechanical properties of PA6/PP nanocomposites were studied by tensile and flexural tests. The microstructure of the nanocomposite were assessed by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD). The dynamic mechanical properties of the PA6/PP blend-based nanocomposites were analyzed by using a dynamic mechanical thermal analyzer (DMTA). The rheological properties were conducted from plate/plate rheometry via dynamic frequency sweep scans. The melt viscosity in a high shear rate region was performed by using a capillary rheometer. The strength and stiffness of the PA6/PP-based nanocomposites were improved significantly with the incorporation of EPRgMA. Adding EPRgMA to the PA6/PP blends resulted in a finer dispersion of the PP phase. TEM and XRD results revealed that the organoclay was dispersed more homogeneously in the presence of EPRgMA, however, mostly in the PA6 phase of the blends. DMTA results showed that EPRgMA worked as an effective compatibilizer. The storage (G′) and loss moduli (G″) assessed by plate/plate rheometry of PA6/PP blends increased with the incorporation of EPRgMA and organoclay. Furthermore, the apparent shear viscosity of the PA6/PP blend increased significantly for the EPRgMA compatibilized PA6/PP/organoclay nanocomposite. This was traced to the formation of an interphase between PA6 and PP (via PA6-g-EPR) and effective intercalation/exfoliation of the organoclay.     

Compatibilization of polypropylene/poly (ethylene oxide) blends and crystallization behavior of the blends

The compatibilization of incompatible polypropylene (PP)/poly(ethylene oxide) (PEO) blends was studied. The experimental results showed that the graft copolymer [(PP-MA)-g-PEO] of maleated PP(PP-MA) and mono-hydroxyl PEO (PEO-OH) was a good compatibilizer for the PP/PEO blends in which PP-MA also had some compatibilization. The crystallization of the blends was affected by the compatibility between PP and PEO. The interfacial behavior of the compatibilizers had an important effect on crystallization behavior of the PP/PEO blends. PEO showed fractionated crystallization in the PP/PEO blends. This behavior was studied from the view point of the theory of fractionated crystallization. © 1994 John Wiley & Sons, Inc.     

Reactive compatibilization of polyamide‐6 (PA 6)/polybutylene terephthalate (PBT) blends by a multifunctional epoxy resin

A multifunctional epoxy resin has been demonstrated to be an efficient reactive compatibilizer for the incompatible and immiscible blends of polyamide‐6 (PA 6) and polybutylene terephthalate (PBT). The torque measurements give indirect evidence that the reaction between PA and PBT with epoxy has an opportunity to produce an in situ formed copolymer, which can be as an effective compatibilizer to reduce and suppress the size of the disperse phase, and to greatly enhance mechanical properties of PA/PBT blends. The mechanical property improvement is more pronounced in the PA‐rich blends than that in the PBT‐rich blends. The fracture behavior of the blend with less than 0.3 phr compatibilizer is governed by a particle pullout mechanism, whereas shear yielding is dominant in the fracture behavior of the blend with more than 0.3 phr compatibilizer. As the melt and crystallization temperatures of the base polymers are so close, either PA or PBT can be regarded as a mutual nucleating agent to enhance the crystallization on the other component. The presence of compatibilizer and in situ formed copolymer in the compatibilized blends tends to interfere with the crystallization of the base polymers in various blends. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 23–33, 2000     

Influence of compatibilization on the mechanical behavior of poly(trimethylene terephthalate)/poly(ethylene-octene) blends

Poly(trimethylene terephthalate) (PTT) based blends toughened with up to 30 wt.% of a partially maleinized poly(ethylene-octene) copolymer (mPEO) were obtained by melt mixing. The blends were composed of two pure amorphous phases and a partially crystalline PEO phase. The rubber modification clearly compatibilized the blends leading to a decrease in the dispersed phase size. The decrease was not enough to attain the brittle-tough transition, but an increase in the shear rate gave rise to an additional decrease in the dispersed phase size and in the interparticle distance (IDc) that led to very high toughness values (15-fold the notched impact strength of the matrix) at rubber contents above 25 wt.%. The critical interparticle distance of the blends was 0.17 μm. A comparison between this IDc and those of PBT/mPEO and PET/mPEO blends was explained in terms of their interfacial tensions.     

Creating super-tough and strong PA6/ABS blends using multi-phase compatibilizers

PA6/ABS blends with excellent mechanical properties are prepared using combination of two effective multi-phase compatibilizers, where finely dispersed domains with unique encapsulation structures are generated for the synergistic improvement in tensile and impact performances.     

Non-isothermal crystallization and melting behavior of compatibilized polypropylene/recycled poly(ethylene terephthalate) blends

Binary blends of polypropylene (PP)/recycled poly(ethylene terephthalate) (r-PET), r-PET/maleic anhydride grafted PP (PP-g-MA), r-PET/glycidyl methacrylate grafted PP (PP-g-GMA), and ternary blends of PP/r-PET (80/20 w/w) compatibilized with various amounts (2-10 wt%) of PP-g-MA or PP-g-GMA were prepared on a twin-screw extruder. The non-isothermal crystallization and melting behavior, and the crystallization morphology were investigated by DSC and POM. The chemical reactions of r-PET with PP-g-MA and PP-g-GMA were characterized by FT-IR. DSC results show that the crystallization peak temperatures of r-PET and PP increased when blending them together, due to the heterogeneous nucleation effect on each other. The of r-PET increased with increasing the content of PP-g-MA while slightly influenced by the content of PP-g-GMA in the binary blends of r-PET with grafted PP, implying different reactivity of r-PET with PP-g-MA and PP-g-GMA. The of PP in the ternary blends retained or slightly decreased, dependent on the compatibilizers and their contents. The melting peak temperature of r-PET in PP/r-PET blends compatibilized by PP-g-MA was lower than that of compatibilized by PP-g-GMA, indicating that PP-g-MA had stronger reactivity towards r-PET compared to PP-g-GMA. The crystallization and melting behavior of blends was influenced by the pre-melting temperature, especially the melting behavior of r-PET in the blends. The crystallization behavior of PP in the blends was also evaluated by Mo’s method. POM confirmed the heterogeneous nucleation effect of r-PET on PP.     

Polymer blends of sPS/PA6 compatibilized by sulfonated syndiotactic polystyrene

Syndiotactic polystyrene (sPS) and polyamide-6 (PA6) are immiscible and incompatible and have been recognized. In this study, sulfonated syndiotactic polystyrene (SsPS-H) is employed as compatibilizer in the blend of sPS/PA6. During melt blending, the sulfonic acid groups of the SsPS-H can interact strongly with the amine end-groups of PA6 through acid-base interaction. In addition, SsPS-H is miscible with sPS when SsPS-H content is less than 20 wt.%. Therefore, the addition of SsPS-H to sPS/PA6 blends reduces the dispersed phase size and improves the adhesion between the phases. The glass transition temperatures of the PA6 component in the compatibilized blends shift progressively towards higher temperature with the content of SsPS-H-12 increase, indicating enhanced compatibility. On the other hand, the progressive lowering of the melting point and crystallization temperatures of PA6 in the blends with increasing SsPS-H contents compared to the incompatibilized blend, provide some insight into the level of interaction between the PA6 and SsPS-H. The compatibilized blends have significantly higher impact strength than the blends without SsPS-H. The best improvement in the impact strength of the blends was achieved with the content of the SsPS-H (11.9 mol%) about 5 wt.%.     

Miscibility and compatibilization of poly(trimethylene terephthalate)/acrylonitrile-butadiene-styrene blends

Poly(trimethylene terephthalate)/acrylonitrile-butadiene-styrene (PTT/ABS) blends were prepared by melt processing with and without epoxy or styrene-butadiene-maleic anhydride copolymer (SBM) as a reactive compatibilizer. The miscibility and compatibilization of the PTT/ABS blends were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), capillary rheometer and scanning electron microscopy (SEM). The existence of two separate composition-dependent glass transition temperatures (T_gs) indicates that PTT is partially miscible with ABS over the entire composition range. In the presence of the compatibilizer, both the cold crystallization and glass transition temperatures of the PTT phase shifted to higher temperatures, indicating their compatibilization effects on the blends.The PTT/ABS blends exhibited typical pseudoplastic flow behavior. The rheological behavior of the epoxy compatibilized PTT/ABS blends showed an epoxy content-dependence. In contrast, when the SBM content was increased from 1 wt% to 5 wt%, the shear viscosities of the PTT/ABS blends increased and exhibited much clearer shear thinning behavior at higher shear rates. The SEM micrographs of the epoxy or SBM compatibilized PTT/ABS blends showed a finer morphology and better adhesion between the phases.     

Improvement in gas permeability of biaxially stretched PET films blended with high barrier polymers: The role of chemistry and processing conditions

Improvement in oxygen gas barrier properties of polyester/polyamide blends used in packaging industry is the main objective of the present study. For this purpose poly(ethylene terephthalate) (PET)/poly(m-xylene adipamide) (nylon-MXD6) (95/5 w/w) and poly(ethylene terephthalate-co-isophthalate) copolymer (PETI)/MXD6 (95/5 w/w) blends have been prepared with a PET copolymer which consists of 5 wt.% sodium sulfonated isophthalate (PET-co-5SIPA) as compatibilizer and a carboxyl-terminated polybutadiene (CTPB) as filler by using a co-rotating intermeshing twin screw extruder. The effects of chemical architecture and morphology on oxygen gas permeability and processability were analyzed by using a range of characterization techniques including differential scanning calorimetry (DSC), scanning electron microscopy (SEM), oxygen gas permeability analyzer, and a special computer controlled uniaxial stretching system that provides real-time measurement of true stress, true strain and birefringence. The morphological analysis revealed that PET-co-5SIPA was an effective compatibilizer for both PET/MXD6 and PETI/MXD6 blends. DSC analysis and spectral-birefringence technique were used to understand the thermal and stress-induced crystallization behavior of the blends. Morphological analysis of the films after biaxial stretching indicated that the spherical nylon phase was converted to 75 nm thick disks during stretching (aspect ratio L/W = 6) that creates a tortuous pathway for oxygen ingress. Stretching enhanced the barrier properties of PET/MXD6 and PETI/MXD6 blends.     

Thermal properties and microhardness of HDPE/clay nanocomposites compatibilized by different functionalized polyethylenes

The calorimetric characteristics, the flammability, the thermal stability and the microhardness of polyethylene high density/clay nanocomposites (HDPE/clay) have been studied by differential scanning calorimetry, thermogravimetry, determination of limiting oxygen index and microhardness tests. The nanocomposites have been compatibilized by ethylene–acrylic acid copolymer (EAA), acrylic acid grafted HDPE (HDAA) and maleic anhydride grafted HDPE (HDMA). The clay was montmorillonite Cloisite 15A. The influence of the presence and the type of the compatibilizers on the properties of the nanocomposites has been evaluated. The results have shown that the thermal stability, the reduction of the flammability and the microhardness of HDPE/clay nanocomposites, compatibilized by HDAA and HDMA are higher than those for nanocomposite compatibilized by EAA. Moreover, the presence and the type of compatibilizer have negligible effect on the characteristics of the HDPE phase transitions. These results have been interpreted by the better clay dispersion and higher level of clay exfoliation in the presence of compatibilizers HDAA and HDMA, than those in the presence of EAA compatibilizer.     

Microhardness and thermal stability of compatibilized LDPE/PA6 blends

Microhardness tests, water absorption and thermogravimetric measurements have been performed on blends of low density polyethylene (LDPE) with different molar mass and polyamide 6 (PA6) compatibilized with 2 pph poly(ethylene-co-acrylic acid) (Escor 5001 by Exxon). The negative deviation of Vickers microhardness from the additivity has been interpreted by changes in the crystallinity of the blend components. The hardness values of the compatibilized blends that are lower than those of the corresponding uncompatibilized blends have been explained by the decrease of the degree of crystallinity of PA6 phase in the presence of Escor. The molar mass of LDPE almost does not influence on the hardness values. The lower water absorption of the compatibilized blends, caused by the formation of a copolymer between PA6 and the compatibilizer leads to microhardness values of the wet compatibilized blends higher than those of the corresponding uncompatibilized blends. The thermogravimetric measurements demonstrate that the thermal stability of blends increases in the presence of 2 pph Escor 5001. The results confirm the compatibilizing efficiency of Escor 5001 towards LDPE/PA6 blends in a wide composition range.