Structure and properties of new polyester elastomers composed of poly(trimethylene terephthalate) and poly(ethylene oxide)

Series of PTT-b-PEO copolymers with different composition of rigid PTT and PEO flexible segments were synthesized from dimethyl terephthalate (DMT), 1,3-propanediol (PDO), poly(ethylene glycol) (PEG, M_n = 1000 g/mol) in a two stage process involving transesterification and polycondensation in the melt. The weight fraction of flexible segments was varied between 20 and 70 wt%. The molecular structure of synthesized copolymers was confirmed by ¹H NMR and ¹³C NMR spectroscopy. The superstructure of these polymers was characterized by DSC, DMTA, WAXS and SAXS measurements. It was observed that domains of three types can exist in PTT-b-PEOT copolymers: semi-crystalline PTT, amorphous PEO rich phase (amorphous PEO/PTT blended phase) and semi-crystalline PEO phase. Semi-crystalline PEO phase was observed only at temperature below 0 °C for sample containing the highest concentration of PEO segment. The phase structure, thermal and mechanical properties are effected by copolymer composition. The copolymers containing 30÷70 wt% of PEO segment posses good thermoplastic elastomers properties with high thermal stability. Hardness and tensile strength rise with increase of PTT content in copolymers.     

Solid-state C NMR and SAXS characterization of the amorphous phase in low-molecular weight poly(ethylene oxide)s

Low-molecular weight poly(ethylene oxide)s (PEO) with extended, once or twice folded chains (as characterized by SAXS), were investigated by solid-state ¹³C NMR spectra measured under conditions to detect only the signal of the narrow line component. The direct detection and integrated intensities of the signals from hydroxy-terminated chain-end units in these spectra confirm that the narrow line component corresponds to the noncrystalline (amorphous) phase. The NMR line of PEO carbons adjacent to the hydroxy end-groups was used as an intensity standard to obtain information on the mean number of carbons per chain contributing to the amorphous phase. Assuming that amorphous phase is formed by chain ends (cilia) and folds it follows from the spectra that the length of folds is 6-7 monomer units; cilia are 2-3 monomer units long.     

Synthesis and characterization of biodegradable aliphatic copolyesters with poly(ethylene oxide) soft segments

A series of multiblock poly(ether-ester)s based on poly(butylene succinate) (PBS) as the hard segments and hydrophilic poly(ethylene oxide) (PEO) as the soft segments was synthesized with the aim of developing degradable polymers which could combine the mechanical properties of high performance elastomers with those of flexible plastics. The aliphatic poly(ether-ester)s were synthesized by the catalyzed two-step transesterification reaction of dimethyl succinate, 1,4-butanediol and α,ω-hydroxyl terminated poly(ethylene oxide) (PEO, = 1000 g/mol) in bulk. The content of soft PEO segments in the polymer chains was varied from about 10 to 50 mass%. The effect of the introduction of the soft PEO segments on the structure, thermal and physical properties, as well as on the biodegradation properties was investigated. The composition and structure of these aliphatic segmented copolyesters were determined by ¹H NMR spectroscopy. The molecular weights of the polyesters were verified by gel permeation chromatography (GPC), as well as by viscometry of dilute solutions and polymer melts. The thermal properties were investigated using differential scanning calorimetry (DSC). The degree of crystallinity was determined by means of DSC and wide-angle X-ray scattering. A depression of melting temperature and a reduction of crystallinity of the hard segments with increasing content of PEO segments were observed. Biodegradation of the synthesized copolyesters, estimated in enzymatic degradation tests in phosphate buffer solution with Candida rugosa lipase at 37 °C was compared with hydrolytic degradation in the buffer solution. The weight losses of the samples were in the range from 2 to 10 mass%. GPC analysis confirmed that there were significant changes in molecular weight of copolyesters with higher content of PEO segments, up to 40% of initial values. This leads to conclusion that degradation mechanism of the poly(ether-ester)s based on PEO segments occurs through bulk degradation in addition to surface erosion.     

Molecular dynamics of poly(ATRIF) homopolymer and poly(AN-co-ATRIF) copolymer investigated by dielectric relaxation spectroscopy

Aiming to develop new dielectric polymers containing CN and F groups with strong dipole moments, a novel copolymer of acrylonitrile (AN) and 2,2,2-trifluoroethyl acrylate (ATRIF) was synthesized in acetonitrile by free radical process as well as the respective homopolymer (poly(ATRIF)). The copolymer’s composition and microstructure were analyzed by FTIR, ¹H and ¹³C NMR spectroscopy and SEC. The molar incorporation of AN determined in the copolymer by NMR was 58 mol%. Thermogravimetric analysis of poly(AN-co-ATRIF) copolymer showed good thermal stability comparatively to the fluorinated homopolymer.Both copolymer, poly(AN-co-ATRIF), and homopolymer, poly(ATRIF), were dielectrically characterized over a frequency range from 10⁻¹ to 10⁶ Hz, and in a temperature range from 223 to 393 K. The dominating relaxation process detected in both materials is the α-relaxation, associated with the dynamic glass transition. A VFTH temperature dependence of the relaxation times (τ) was found for both materials, as characteristic of cooperative processes, from which the respective glass transition temperatures (T_g(τ = 100 s)) were estimated, which differ ∼40 K, the one of the copolymer being higher (307 K) in accordance to the calorimetric analysis. This effect was attributed to a higher stiffness of the backbone in the copolymer originated by the inclusion of the acrylonitrile groups. Both relaxation functions have the same breath of relaxation times allowing constructing a single master curve, indicating similar non-exponential character. A less fragile behavior was found for the copolymer. This was rationalized in a more straightforward way by the free volume approach instead from a correlation between fragility and intermolecular coupling. It was found that in the copolymer the free volume increases at a lower rate with the temperature increase. It was inferred from the VFTH temperature dependence of the dc conductivity and low values of the decoupling index that ion motion is significantly influenced by the dynamics of the α-process.     

Characterization of poly(carboxylic acid)/poly(ethylene oxide) blends formed through hydrogen bonding by spectroscopic and calorimetric analyses

The solid state of the complex between poly(acrylic acid) (PAA) and poly(ethylene oxide) (PEO), and that between poly(methacrylic acid) (PMAA) and PEO formed via hydrogen-bonding was studied by differential-scanning calorimetric (DSC) and by Fourier-transform infrared (FT–IR) spectroscopic measurements. Melting temperature T_m and the degree of the crystallinity X_c of PEO in the systems PAA (or PMAA)/PEO blends obtained from aqueous or dimethyl sulfoxide (DMSO) medium were measured in various unit mol % of PEO ([PEO]100/{[PAA(or PMAA)] + [PEO]}) where [ ] is the unit mole concentration. It was found that 50 unit mol % of PEO is a critical composition, which gives new evidence for the 1 : 1 complex formation between PAA (or PMAA) and PEO. From the FT–IR spectroscopic analysis in conjunction with DSC measurements we also found that the effects of solvent and of hydrophobic interaction (due to the α-methyl group of PMAA) are the important factors controlling the complexation in the solution and solid systems. These factors also affect the crystallization behavior and the microstructure of the PAA (or PMAA)/PEO blend in solid state.     

Non-isothermal depolymerisation kinetics of poly(ethylene oxide)

The depolymerisation of low molecular weight poly(ethylene oxide) (PEO) under mild conditions was studied using a linear temperature ramped non-isothermal technique and the results compared with those obtained from a conventional isothermal technique. The analysis of the non-isothermal kinetic (NIK) data was performed using an original computer program incorporating an algorithm that systematically minimizes the sum of the squares of the residuals between the experimental data and the calculated theoretical kinetic profile in order to extract the kinetic parameters. The results revealed that the depolymerisation of PEO proceeds in accordance with the Ekenstam model and follows the Arrhenius equation over the temperature range of ca. 40-130 °C. The NIK analysis resulted in a two-dimensional convergence to produce a unique solution set for the kinetic parameters of E_a = 89.4 kJ mol⁻¹ and A = 9.6 × 10⁶ h⁻¹. These data are consistent with the results obtained from the isothermal experiments. It is proposed that NIK analysis is a quick and reliable means of obtaining kinetic parameters relevant to lifetime predictions in polymers whose degradation behaviour can be considered to be close to ideal.     

Studies on interpolymer self-organisation behaviour of protoporphyrin IX bound poly(carboxylic acid)s with complimentary polymers by means of fluorescence techniques

Covalently bound protoporphyrin IX was used as a fluorophore to investigate the interpolymer complex formation between the poly(carboxylic acid)s, PMAA/PAA and poly(N-vinyl pyrrolidone), PVP, poly(ethylene oxide), PEO or poly(ethylene glycol), PEG. Absorption and emission spectral properties of protoporphyrin IX bound to PAA, PMAA and PVP have been studied. Protoporphyrin IX in poly(MAA-co-PPIX) was found to be present in the dimer or higher aggregated form at low pH due to the environmental restriction imposed by the polymer whereas in the case of poly(AA-co-PPIX) and poly(VP-co-PPIX), PPIX exists in monomeric form. The fluorescence intensity and lifetime of PPIX bound to poly(carboxylic acid)s increase on complexation through hydrogen bonding with PVP, PEO and PEG due to the displacement of water molecules in the vicinity of the PPIX. Poly(MAA-co-PPIX) shows longer fluorescence lifetime due to the more compact interpolymer complexation as compared to poly(AA-co-PPIX) due to the enhanced hydrophobicity of PMAA. Poly(VP-co-PPIX) shows a decrease in the fluorescence lifetime on complexation with PMAA or PAA due to the hydrophilic and microgel like environment of the fluorophore bound to PVP. The contrasting behaviour of the same polymer adduct with respect to the site of the fluorophore is interpreted to be due to the solvent structure which determines the environment of the fluorophore.     

聚(3-羟基丁酸酯)/聚氧化乙烯共混物非晶区相容性的固体核磁共振研究

用固体高分辨核磁共振碳谱方法研究了不同组成比的聚 (3 羟基丁酸酯 ) 聚氧化乙烯共混物的结晶度、非晶区的相容性和分子运动能力 .结果表明聚 (3 羟基丁酸酯 )的结晶度几乎不随组成比变化 ,而聚氧化乙烯的结晶度则随其在共混物中含量的降低而显著降低 .聚氧化乙烯的加入使得聚 (3 羟基丁酸酯 )非晶区的分子运动能力有所增强 .共混物的非晶区表现出一定的相容性 ,相容程度与共混物的组成比有关     

Synthesis of four‐armed poly(ε‐caprolactone)‐block‐poly(ethylene oxide) by diethylzinc catalyst

Biodegradable, amphiphilic, four‐armed poly(?‐caprolactone)‐block‐poly(ethylene oxide) (PCL‐b‐PEO) copolymers were synthesized by ring‐opening polymerization of ethylene oxide in the presence of four‐armed poly(?‐caprolactone) (PCL) with terminal OH groups with diethylzinc (ZnEt₂) as a catalyst. The chemical structure of PCL‐b‐PEO copolymer was confirmed by ¹H NMR and ¹³C NMR. The hydroxyl end groups of the four‐armed PCL were successfully substituted by PEO blocks in the copolymer. The monomodal profile of molecular weight distribution by gel permeation chromatography provided further evidence for the four‐armed architecture of the copolymer. Physicochemical properties of the four‐armed block copolymers differed from their starting four‐armed PCL precursor. The melting points were between those of PCL precursor and linear poly(ethylene glycol). The length of the outer PEO blocks exhibited an obvious effect on the crystallizability of the block copolymer. The degree of swelling of the four‐armed block copolymer increased with PEO length and PEO content. The micelle formation of the four‐armed block copolymer was examined by a fluorescent probe technique, and the existence of the critical micelle concentration (cmc) confirmed the amphiphilic nature of the resulting copolymer. The cmc value increased with increasing PEO length. The absolute cmc values were higher than those for linear amphiphilic block copolymers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 950–959, 2004     

Synthesis and characterization of well‐defined diblock and triblock copolymers of poly(N‐isopropylacrylamide) and poly(ethylene oxide)

Well‐defined diblock and triblock copolymers composed of poly(N‐isopropylacrylamide) (PNIPAM) and poly(ethylene oxide) (PEO) were successfully synthesized through the reversible addition–fragmentation chain transfer polymerization of N‐isopropylacrylamide (NIPAM) with PEO capped with one or two dithiobenzoyl groups as a macrotransfer agent. ¹H NMR, Fourier transform infrared, and gel permeation chromatography instruments were used to characterize the block copolymers obtained. The results showed that the diblock and triblock copolymers had well‐defined structures and narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight < 1.2), and the molecular weight of the PNIPAM block in the diblock and triblock copolymers could be controlled by the initial molar ratio of NIPAM to dithiobenzoate‐terminated PEO and the NIPAM conversion. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4873–4881, 2004     

The synthesis and characterization of monodisperse poly(acrylic acid) and poly(methacrylic acid)

A number of polyacrylic (PAA) and polymethacrylic (PMAA) acids have been synthesized by living anionic polymerization of the monomeric tert-butyl esters followed by subsequent hydrolysis of the corresponding polyesters. The necessary precautions were taken in order to assure good molecular weight control, as well as high yields in the polymerization reactions. The intermediate and final polymers were characterized by gel permeation chromatography and NMR-H¹ spectrometry.     

Effect of aging on fractional crystallization of poly(ethylene oxide) component in poly(ethylene oxide)/poly(3‐hydroxybutyrate) blends

The effect of aging on the fractional crystallization of the poly(ethylene oxide) (PEO) component in the PEO/poly(3‐hydroxybutyrate) (PHB) blend has been investigated. The partial miscibility of the PEO/PHB blends with high PEO molecular weight (M_v = 2.0 × 10⁵ g/mol) was confirmed by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis. The fractional crystallization behavior of the PEO component in the PEO/PHB blends with low PEO content (not more than 30 wt% of PEO), before and after aging under vacuum at 25 °C for 6 months, were compared by DSC, fourier transform infrared microscopic spectroscopy, small angle X‐ray diffraction, and scanning electron microscopy. It was confirmed that nearly all the PEO components remain trapped within interlamellar regions of PHB for the PEO/PHB blends before aging. Under this condition, the crystallization of PEO is basically induced by much less active heterogeneities or homogeneous nucleation at high supercoolings. While, after the same PEO/PHB samples were stored at 25 °C in vacuum for 6 months, a part of the PEO component was expelled from the interlamellar region of PHB. Under this condition, the expelled PEO forms many separate domains with bigger size and crystallizes at low supercoolings by active heterogeneous nucleation, whereas the crystallization of PEO in the interlamellar region is still mainly induced by less active heterogeneities or homogeneous nucleation at extreme supercoolings. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2665–2676, 2005     

Universal drag reduction characteristics of saline water-soluble poly(ethylene oxide) in a rotating disk apparatus

 Polymer-induced turbulent drag reduction in a rotating disk apparatus was investigated using nonionic poly(ethylene oxide) (PEO) in a synthetic saline solution with novel application to ocean thermal energy conversion technology. A maximum total (skin friction plus form) drag reduction of 30% was obtained with 50 wppm of PEO with molecular weight 5.0 × 10⁶. The concentration dependence of the percentage drag reduction for the PEO/saline solution system is found to fit Virk's empirical correlation, and a universal correlation for various molecular weights and Reynolds numbers is also presented. Furthermore, hydrodynamic volume fraction was introduced to correlate drag reduction efficiency with molecular parameters in this PEO/saline solution system. Received: 28 December 1999/Accepted: 17 February 2000     

Synthesis and micelle formation of triblock copolymers of poly(methyl methacrylate)-b-poly(ethylene oxide)-b-poly(methyl methacrylate) in aqueous solution

Amphiphilic triblock copolymers of poly(methyl methacrylate)-b-poly(ethylene oxide)-b-poly(methyl methacrylate) (PMMA-b-PEO-b-PMMA) with well-defined structure were synthesized via atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) initiated by the PEO macroinitiator. The macroinitiator and triblock copolymer with different PMMA and/or PEO block lengths were characterized with ¹H and ¹³C NMR and gel permeation chromatography (GPC). The micelle formed by these triblock copolymers in aqueous solutions was detected by fluorescence excitation and emission spectra of pyrene probe. The critical micelle concentration (CMC) ranged from 0.0019 to 0.016 mg/mL and increased with increasing PMMA block length, while the PEO block length had less effect on the CMC. The partition constant K_v for pyrene in the micelle and in aqueous solution was about 10⁵. The triblock copolymer appeared to form the micelles with hydrophobic PMMA core and hydrophilic PEO loop chain corona. The hydrodynamic radius R_h,app of the micelle measured with dynamic light scattering (DLS) ranged from 17.3 to 24.0 nm and increased with increasing PEO block length to form thicker corona. The spherical shape of the micelle of the triblock copolymers was observed with an atomic force microscope (AFM). Increasing hydrophobic PMMA block length effectively promoted the micelle formation in aqueous solutions, but the micelles were stable even only with short PMMA blocks.     

Preparation of telechelic oligomers by controlled thermal degradation of isotactic poly(1-butene) and poly(propylene-ran-1-butene)

It was found that telechelic isotactic oligo(1-butene) and telechelic oligo(propylene-ran-1-butene) could be isolated as nonvolatile oligomers from polymer residues resulting from the thermal degradation of isotactic poly(1-butene) and poly(propylene-ran-1-butene), respectively. Their structures were determined by ¹H and ¹³C NMR with attention being paid to their reactive end groups. The maximum average number of terminal vinylidene groups per molecule (f_TVD) was 1.8, indicating that about 80 mol% were α,ω-diene oligomers having two terminal vinylidene groups. This useful new telechelic oligomer had a lower polydispersity than the original polymer, in spite of its lower molecular weight and T_m. The composition of end groups of nonvolatile oligomers obtained by thermal degradation of poly(propylene-ran-1-butene) could be explained by the differences in bond dissociation energy and activation energy of elementary reactions during thermal degradation, based on the monomer composition of the original polymer.     

Volume phase transition and structure of poly(N-isopropylacrylamide) microgels studied with 1H-NMR spectroscopy in D2O

Thermoresponsive colloidal microgels were prepared by polymerisation of N-isopropylacrylamide (NIPAM) with varying concentration of a cross-linking monomer, N,N-methylenebisacrylamide (MBA), in water with either 0.4 or 6.7 mM concentration of an anionic surfactant, sodium dodecylsulphate (SDS). Volume phase transitions of the prepared microgels were studied in D₂O by ¹H-NMR spectroscopy including the measurements of spin–lattice (T1) and spin–spin (T2) relaxation times for the protons of poly(N-isopropylacrylamide) (PNIPAM) at temperature range 22–50 °C. In addition, microcalorimetry, turbidometry, dynamic light scattering and electrophoretic mobility measurements were used to characterise the aqueous microgels. The results from the different characterisation methods indicated that PNIPAM microgels prepared in 6.7 mM SDS concentration are structurally different compared to their correspondences prepared in 0.4 mM concentration. Increasing MBA concentration in the microgel synthesis appears to increase the structural heterogeneity in both cases of SDS concentration. PNIPAM structures with significantly higher molecular mobilities at temperatures above 35 °C were observed in the microgels prepared in 0.4 mM SDS concentration, as indicated by the ¹H NMR relaxation times of different PNIPAM protons. We conclude that the high mobilities measured with NMR at elevated temperatures and also the clearly negative values of zeta potential are in connection to a fairly mobile surface layer with polyelectrolyte nature and a consequent high local lower critical solution temperature.     

Characterization of poly(acrylamide-co-acrylates) obtained by inverse microemulsion polymerization

Two series of poly(acrylamide-co-acrylates) with compositions rangingfrom 10 to 55 mol % acrylate units were prepared by radical polymerization in inverse microemulsions. The compositional analyses of the samples were performed using elemental analysis, potentiometry and¹³C NMR. The comparison between the three methods indicates that¹³C NMR is the most reliable one, avoiding errors which often arise from associated water in hydrophilic polymers. The copolymer viscosity exhibits a maximum behavior around 40 mol % acrylate content, a lower value than that already observed for co-polymers prepared in homogeneous solution. The production of copolymers presenting high intrinsic viscosities ( 3700 cm³g^–) is achieved using an inverse microemulsion as the polymerization medium operating at lower temperature.     

Polymerization of Bis(Pyridine)bis-(2,4,6-tribromophenoxo)copper(II) Complex (Py2Cu(TBrP)2) by Electrooxidation and Structural Characterization by 1H-NMR, 13C-NMR,and FTIR Spectroscopies

Abstract

Electroinitiated polymerization of bis(2,4,6-tribromophenoxo)- bis(pyridine)copper(II) complex was achieved in dimethylformamide-tetrabutylammonium tetrafluoroborate solvent-electrolyte couple under air or nitrogen at room temperature by constant potential electrolysis. Polymerization conditions were based on the peak potentials measured by cyclic voltammetry. The structural analyses of the polymers were done by ¹H-NMR, ¹³C-NMR, and FTIR spectral analyses along with molecular weight measurements by cryoscopy. The poly(dibromo phenylene oxide)s obtained only at oxidation potentials in either atmosphere were found to be highly linear, indicating mainly 1,4-catenation was taking place.     

Thermal ageing of poly(ethylene oxide)/poly(3,4-ethylenedioxythiophene) semi-IPNs

The thermal stability study of a conducting semi-IPN has been reported. The thermo-oxidation of poly(ethylene oxide) (PEO)/poly(3,4-ethylenedioxythiophene) (PEDOT) semi-Interpenetrating Polymer Network (semi-IPN) was studied at 80 °C in open air. The degradation was followed by spectrophotometry in the visible and near infrared range, cyclic voltamperometry and thermogravimetric analysis. Fluorescence spectrophotometry allowed for the identification of OH by-product originated in the PEO network degradation by the use of a chemiluminescent probe, typically terephthalic acid. The formation of hydroxyl radicals damaged the PEDOT chains as checked by infrared spectroscopy. The mechanism of degradation is further confirmed (i) by introducing a radical scavenger or (ii) by performing a thermal ageing under inert atmosphere; in both cases the semi-IPN life-time is tremendously increased.     

NMR study of phase separation in D2O/ethanol solutions of poly(N-isopropylmethacrylamide) induced by solvent composition and temperature

¹H and ¹³C NMR spectroscopies were applied to investigate phase separation in solutions of poly(N-isopropylmethacrylamide) (PIPMAm) in D₂O/ethanol (EtOH) mixtures induced by solvent composition (cononsolvency) and temperature. Effects of EtOH content in D₂O/EtOH mixtures and temperature on the appearance and extent of the phase separation were characterized. Differences in mesoglobules formed during the phase separation induced by cononsolvency and temperature were found. For temperature-induced phase separation, ¹³C spin-spin relaxation times showed that besides the free EtOH expelled from the PIPMAm mesoglobules, there are also EtOH molecules bound in these mesoglobules. On the other hand, virtually no bound EtOH molecules were detected for mesoglobules formed as a consequence of the cononsolvency. For PIPMAm random copolymers containing negatively charged methacrylate units the phase separation induced by solvent composition was not observed.