Influence of prepolymers molecular weight on the viscoelastic properties of aqueous HEUR solutions

A series of hydrophobically modified ethoxylated urethanes (HEURs) were synthesized by a step growth polymerization of polyethylene glycol with dicyclohexylmethane diisocyanate (H12MDI). The thickeners were produced with different sizes of the hydrophilic section by changing the molar ratios of reactants. The size of the hydrophobic ends was constant for all prepared samples. The changes in hydrophilic lengths were correlated with the rheological properties of HEURs aqueous solutions. The intrinsic viscosity measurements showed that associates are present even at very low concentration. The response of these HEUR systems in aqueous solution to both steady shear and oscillatory shear was determined as a function of hydrophilic chain length and polymer concentration. Dramatic increases in viscosity are observed with decreasing molecular weight of the prepolymer (with a decrease of the hydrophilic components' size and at the same time an increased ratio between hydrophobic and hydrophilic sections of HEURs). Also, a steep increase in viscosity with increasing thickener concentration is obtained. The rheological properties of aqueous solutions of HEUR polymers can be described using a simple Maxwell model with a single relaxation. The dynamic measurements verified the results obtained from the steady state measurements about the hydrophilic section size and its effect on the association phenomenon.     

Rheological properties of a telechelic associative polymer in the presence of alpha- and methylated beta-cyclodextrins

The viscosity of hydrophobic ethoxylated urethane (HEUR) solution decreased in the presence of alpha-CD or m-beta-CD; however their interactions were quite different. When the alpha-CD/hydrophobe molar ratio exceeded 5.0, the viscosity was close to that of a PEO solution of similar molecular weight. Oscillatory shear indicated that the mechanically active chains in HEUR solution decreased with the addition of alpha-CD. This agreed with the hypothesis that alpha-CD formed an inclusion complex with the hydrophobic moiety of the HEUR polymer, thereby destroying the transient hydrophobic associative network. The viscosity/temperature relationship of the alpha-CD/HEUR system (for HEUR with 70% of the PEO chains capped at both ends) did not obey the Arrhenius relationship for alpha-CD/hydrophobe molar ratio in the range 0.8-5.0. The low shear viscosity increased with increasing temperature at molar ratio of 1.0, and this was attributed to the competitive complexation of the alpha-CD/hydrophobe and the alpha-CD/PEO chain. Increasing temperature favored alpha-CD/PEO complexation. Comparison between the behavior of alpha-CD/HEUR and m-beta-CD/HEUR resulting from the different binding characteristics was discussed.     

含二十二烷基聚氧乙烯醚甲基丙烯酸酯功能单体的缔合型乳液增稠剂的制备及表征

以甲基丙烯酸、丙烯酸乙酯、邻苯二甲酸二烯丙酯和不同量的功能单体二十二烷基聚氧乙烯醚甲基丙烯酸酯(BEM)为原料,采用半连续乳液聚合方法合成了疏水改性碱溶性缔合型增稠剂乳液.测定了增稠剂乳液的粘度、透光率、乳胶粒粒径及其分布等性能,考察了不同固含量下乳液粘度和透光率随pH的变化情况.结果表明随着BEM用量的增加,乳胶粒粒径逐渐增大.随着pH值的增加,乳液的粘度首先迅速升高,然后缓慢下降.与不含BEM的增稠剂乳液相比,当乳液固含量大于0.5%,BEM含量占单体量低于5.0wt%时,该缔合型增稠剂的增稠效果和抗剪切性有显著提高,BEM含量较高(8.0wt%或更高)时反而使增稠效果和抗剪切性变差.在此基础上研究了增稠剂对苯丙乳液的增稠效应,结果显示BEM含量占单体量的2.5wt%时,对苯丙乳液的增稠作用最好.与使用功能单体三苯乙基苯酚聚氧乙烯醚甲基丙烯酸酯改性的增稠剂相比,含BEM的增稠剂在BEM用量较少的情况下就能起到明显的增稠效果.     

含三苯基乙基苯氧基聚氧乙烯醚甲基丙烯酸酯功能单体的缔合型乳液增稠剂的制备及增稠机理

采用半连续法乳液聚合以甲基丙烯酸、丙烯酸乙酯、邻苯二甲酸二烯丙酯和不同量的功能单体三苯基乙基苯氧基聚氧乙烯醚甲基丙烯酸酯(SEM-25)为原料合成了疏水改性碱溶性增稠剂乳液. 测定了增稠剂乳液的粘度、透光率、pH、粒径及其分布, 结果表明随着pH值的增加, 乳液的粘度和透光率首先迅速升高, 然后缓慢下降. 随着SEM-25用量的增加, 乳胶粒的粒径先增大后减小. 与不含SEM-25的乳液增稠剂相比较, SEM-25低含量增稠剂的增稠效果和抗剪切性没有提高, 只有当SEM-25用量提高至单体质量的12%, 且乳液固含量大于0.65%时, 所制备缔合型增稠剂乳液的粘度和流变性比不含SEM-25的增稠剂才有明显提高. 在此基础上研究了增稠剂对苯丙乳液的增稠性. 含有增稠剂的苯丙乳液的粘度和透光率随pH值的变化与纯增稠剂乳液的变化类似. 只有当加入0.34 wt%苯丙乳液固体质量的增稠剂, 并且增稠剂中SEM-25含量达到5 wt%时苯丙乳液的粘度与使用不含SEM-25的增稠剂增稠的粘度相比才有明显增高. 在此基础上对增稠剂的增稠机理进行了探讨.     

Surfactant and Electrolyte Effects on Latex Depletion Flocculation by Thickeners

Summary: Polymer thickeners can induce good dispersion, bridging, or depletion flocculation of latexes depending on the polymer structure and concentration. Unlike non-associative polymers, associative polymers have the ability to create a good latex dispersion. However, when the associative interactions are destroyed, depletion flocculation of the latex can result. This happens when an excess of ionic surfactant is added to the system. In addition, the surfactant may associate with the thickener backbone, thus modifying the molecular volume of the polymer thickener. This paper explores the effect of anionic surfactant and electrolyte on the molecular volume of both associative and non-associative thickeners. Both HEUR and HASE structures are included. For HEUR thickeners, formation of a pseudo-polyelectrolyte through the association of anionic surfactant with the polyethylene oxide backbone is confirmed. Further, the ability of the thickener to depletion flocculate latexes as a function of surfactant and electrolyte is explored. Experimental critical flocculation concentrations (CFC) are compared to values expected based on molecular volume and potential energy calculations. A good correlation is found between molecular volume and CFC for a wide range of thickener compositions.     

水性乳液/聚氨酯模型缔合增稠剂的触变性机理

以异佛尔酮二异氰酸酯(IPDI)与聚乙二醇(PEG,分子量为4000,6000和8000)为原料,以直链醇(C12,C14,C16和C18)为封端剂,合成了疏水改性乙氧基化氨基甲酸酯(HEUR),并将其应用于乳液增稠.采用核磁共振波谱(¹H NMR)、傅里叶变换红外光谱(FTIR)及凝胶渗透色谱(GPC)表征了HEUR的结构、分子量及其分布,研究了其在水性乳液中的流变行为.研究结果表明,当HEUR封端基团为C14,C16和C18,且质量分数增加到1. 0%以上时,增稠的乳液(Latex/HEUR)的流变曲线出现触变环,为触变性流体.当HEUR亲疏水比值(R_h)减小时,疏水性增强,触变环向低剪切速率(γ˙)方向移动,黏度下降率(Δη)增大;当HEUR用量增加时,触变环面积(S_loop)也增大.这些触变性特点归因于HEUR在乳液中的缔合作用、氢键作用及链缠结.利用扫描电子显微镜(SEM)和原子力显微镜(AFM)对Latex/HEUR的聚集态和表面形貌进行了表征.结果表明,随着HEUR封端基团链长增加,Latex/HEUR颗粒...     

Viscoelastic behaviour of butyl acrylate/styrene/2-hydroxyethyl methacrylate/acrylic acid latices thickened with associative thickeners

The rheological behaviour of butyl acrylate/styrene/acrylic acid latices thickened with a hydrophobically modified ethoxylated polyurethane (HEUR) or hydrophobically modified alkali-soluble polyacrylate emulsion (HASE) was investigated. While the pseudoplastic character of frequency dependence of complex viscosity was similar for both thickeners, viscoelastic behaviour, expressed as the ratio of loss and storage moduli, significantly differed, indicating that the HEUR molecules, unlike swollen HASE particles, create a viscoelastic space structure. The increase in hydrophilicity of the particle surface, achieved by incorporation of 2-hydroxyethyl methacrylate (HEMA) monomer into the latex copolymer reduced the viscoelasticity of latices thickened with HEUR, but not of those thickened with HASE. This confirms that adsorption of hydrophobic end-groups on particle surface is important for thickening of latices with HEUR and that a physical network of latex particles interconnected by the thickener macromolecules is formed. To cite this article: O. Quadrat et al., C. R. Chimie 6 (2003).     

Synthesis and characterization of cubic cobalt oxide nanocomposite fluids

Narrow size distribution cubic Co₃O₄ nanoparticles were synthesized and rheological properties of suspensions of the cubes in oligomeric polyethylene glycol (PEG) were explored over a range of particle volume fractions and rotational shear flow conditions. At low and high particle volume fractions, the relative viscosity of the suspensions is described by a Krieger–Dougherty formula with an intrinsic viscosity consistent with expectations for suspensions of ideal cuboids. At intermediate to high particle loadings, the suspensions manifest complex rheological behavior, including shear thinning and shear-thickening features. These observations are discussed in terms of the charge carried by the cubes and the shear rate/volume fraction dependency of the transition from shear thinning to shear thickening.     

Study of a shear thickening fluid: the suspensions of monodisperse polystyrene microspheres in polyethylene glycol

The monodisperse polystyrene (PS) microspheres were prepared by dispersion polymerization. The rheological properties of shear thickening fluid (STF) based on PS microspheres dispersing in polyethylene glycol with different concentrations were studied through the steady and oscillatory shear at different temperatures, respectively. All suspensions successively present the first shear thinning, the shear thickening, and the second shear thinning. The experimental results indicate that the shear thickening behavior of STF is controlled by the concentration of PS microspheres and temperature, as changed from continuous shear thickening (CST) to discontinuous shear thickening (DST) with increasing solid content or decreasing temperature. The STF is affected by shear rate, temperature, and the viscosity of the dispersed medium, and it is reversible absolutely and presents transient response ability. Both CST and DST behave as dilatancy. The PS microsphere aggregations formed under shear stress may result in the shear thickening in STFs.     

A novel associative latex thickener using ethoxylated behenyl methacrylate as functional monomer

<正>Alkali-soluble associative latex thickeners modified with hydrophobic long chain alkyl groups were prepared using common acrylics and varying amount of a functional monomer,ethoxylated behenyl methacrylate(BEM),through emulsion polymerization.It was found that the size of the emulsion particle became larger with addition of BEM.The light transmittance of the thickener latex sharply increased with pH varied from 6 to 7.The associative latex thickener manifested a higher viscosity when solids in the latex thickeners were kept at 0.5 wt%or higher,and the optimal amount of BEM was found to be around 2.5 wt%,or 0.16 mol%.All thickener latexes modified with BEM have better shearing resistance than the BEM-free thickener.     

Rheological Properties of Hydrophobically Modified Poly(acrylic acid) in Mixed Solutions

Hydrophobically modified poly(acrylic acid) (HMPA) with single-tailed pendant side groups was prepared by precipitation polymerization. The effects of polymer concentration, surfactant and co-solvent on the solution properties of HMPA were investigated. HMPA solutions showed good viscosity enhancement and typical shear thinning behavior with increasing concentration. The surfactant TX-10 and co-solvent ethylene glycol gave rise to factors that changed the hydrophobic interactions and in turn the rheology behavior of the solutions. The transient associative network of HMPA in ethylene glycol + water mixed solutions was retained as the temperature was decreased to below 0 °C.     

丙烯酰胺-苯乙烯双亲嵌段共聚物水溶液的粘度性能

通过改变丙烯酰胺 (AM)与苯乙烯 (St)两单体的投料比 ,在微乳液介质中制备了分子组成系列变化的丙烯酰胺 苯乙烯双亲嵌段共聚物 (PAM b PSt) ,使用旋转粘度计测定了共聚物水溶液的表观粘度 ,详细考察了共聚物浓度、共聚物链结构、剪切速率、盐度及温度等因素对共聚物水溶液表观粘度的影响规律 .研究结果表明 ,由于PAM b PSt分子链中的PSt疏水嵌段链段之间具有强的疏水缔合作用 ,导致其具有独特的流变性能 .当共聚物水溶液的浓度高于某一临界值后 ,疏水缔合作用以分子间的缔合为主 ,大分子链之间会形成动态物理交联网络 ,增大了流体力学体积 ,使PAM b PSt水溶液可产生良好的增稠性能 ;疏水缔合作用是一吸热过程 ,升高温度有利于分子间的缔合 ,因此PAM b PSt水溶液具有良好的耐温性 ;聚合物水溶液中盐类物质的存在 ,会增强溶剂的极性 ,有利于分子间的缔合 ,使PAM b PSt水溶液具有良好的耐盐性 .     

Microphase separation of PEG-modified urethane acrylate and the swelling behavior of its gels

The viscosity of PEG-modified urethane acrylate (PMUA) showed peculiar behavior in the course of soap-free emulsification. Moreover, the viscosity change with added amounts of water was influenced by the reaction molar ratio of polyethylene glycol (PEG). The rate of increase in viscosity slowed and the ratio of increase in viscosity increased as the reaction molar ratio of PEG increased. This peculiar viscosity behavior was due to the microphase separation between hydrophilic and hydrophobic segments of PMUA, and the orientation of polyoxyethylene groups at O/W interface which influenced droplet size of the soap-free PMUA emulsion. The location of polyoxyethylene groups of this resin at O/W interface was confirmed using the adsorption isotherm measurement of PMUA molecules containing polyoxyethylene groups at water/benzene interface. The microphase separation behavior of PMUA between hydrophilic and hydrophobic segments could apply to the preparation of the PMUA gels containing peculiar structure. PMUA gels were prepared using dioxane (UAG) and the swelling behavior of these gels were compared to that of gels prepared using water (UAHG) in the same medium. In the same medium, the swelling behavior of UAHG gels differed from that of UAG gels because of the difference in the microstructure of gel due to the microphase separation between hydrophilic and hydrophobic segments. This phase separation in the course of gelation in water could be confirmed using contact angle measurement.     

Rheological characterization of the dilatant flow behavior of highly substituted hydroxypropylmethyl- cellulose solutions in the presence of sodium lauryl sulfate

 The flow behavior of aqueous solutions of three highly substituted, hydrophobic hydroxypropylmethylcelluloses (HPMC) in mixtures containing the anionic surfactant sodium lauryl sulfate (SLS) was investigated both rheo-mechanically and rheo-optically. For the first time it was possible to demonstrate dilatant flow in these systems, a phenomenon which is otherwise only known of some suspensions and associative thickening solutions. Without addition of SLS, the aqueous HPMC solutions showed the predicted flow behavior of polymer solutions, and the Cox–Merz rule was fulfilled. With the addition of SLS to these HPMC solutions, the least hydrophobic HPMC displayed no dilatancy. The solutions of a more hydrophobic HPMC with SLS exhibited on the one hand an increase in viscosity, and on the other hand shear thinning as well as shear thickening. The most hydrophobic HPMC displayed more clearly the effects of an SLS-dependent viscosity increase and the appearance of dilatant flow. At constant HPMC concentration (0.5% w/w), a maximum increase in viscosity (factor 15) was observed in the critical micelle concentration range for SLS. By rheo-optical measurements it was possible to detect an unusually pronounced alignment of the polymer segments as well as a sharp increase in the birefringence values, even before the macroscopic occurrence of dilatant flow. According to the existing network theories, this behavior of the aqueous solutions of highly substituted HPMCs in mixture with SLS has been interpreted as a shear-induced transition from intra-molecular to intermolecular interactions. Received: 4 February 1998 Accepted: 13 March 1998     

Characterization,solution properties,and morphologies of a hydrophobically associating cationic terpolymer

The acrylamide‐based terpolymers (PADB) with 4‐butylstyrene (BST) as the hydrophobic monomer and dimethyldiallyammonium chloride (DMDAAC) were synthesized by the micellar free radical technique. The polymer was determined by UV, FT‐IR and ¹HNMR, and the hydrophobic microblock structure of PADB was characterized successfully by the conventional DSC measurement. The use of DMDAAC improves the water solubility and intermolecular association of terpolymers. The feed amount of BST affects greatly the apparent viscosity of PADB solution. The polymer exhibits good viscosification property, salt resistance, temperature‐thickening, thixotropy, pseudoplastic behavior and shear‐thickening at low shear rate. The apparent viscosities of PADB solution remarkably increase by the addition of a small amount of surfactant. AFM measurements show that hydrophobic aggregates have been formed in 0.1 g dL^?1 PADB aqueous solution, indicative of strong associations of hydrophobic groups, which are reinforced with increasing PADB concentration. The microstructures of PADB are disrupted by the addition of small amounts of salt, resulting in the decrease in solution viscosity. However, with increasing NaCl concentration, the tree‐like associating structures are formed, leading to the increase in the solution viscosity of PADB. The AFM results reveal that the solution properties of PADB are due to the associating structures in the aqueous solution and brine solution. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 826–839, 2007     

Temperature effect of hydrophobically modified polyethylene oxide at the air–water interface

Surface pressure (π)–area (A) isotherms of hydrophobically modified polyethylene oxide (HEUR) at the air–water interface was examined. Conformational transitions between pancake, mushroom, and brush states of the hydrophilic backbone influence the intermolecular interaction between the hydrophobic chains. We choose relatively long (18 carbons) hydrophobic ends, which have large hydrophobic interactions, and investigate the main chain effect by change in the length of the hydrophilic PEO chain. At high surface concentration region, the temperature coefficient of surface pressure, dπ/dT, was larger by increasing the portion of the hydrophobicity. This indicates an increase in surface energy and a decrease in surface enthalpy at high surface concentrations. As alkyl chains on both sides of HEURs are anchored at the air–water interface, restriction caused by the alkyl chain would be smaller for the long PEO chain, but the larger for the short PEO chain length.     

SiO2/聚乙二醇非牛顿流体流变性能研究

利用应力控制流变仪考察了SiO₂/聚乙二醇分散体系稳态和动态的流变性能. 实验结果表明, 该体系具有剪切变稀和可逆的剪切增稠现象. 稳态应力实验中, 当应力较小时, 体系具有剪切变稀现象, 而在剪切应力(σ)大于临界剪切应力(σ_c^s, σ_c^s=9.99 Pa)后, 体系粘度急剧增大. 在动态实验中, 剪切应力小于临界剪切应力(σ_c^o, σ_c^o=15.85 Pa)时, 储能模量G′减小, 耗能模量G″与复合粘度η*基本不变, 但σ＞15.85 Pa后, G′、G″及η*同步增大, 且在所研究的应力范围内, G″均大于G′. 同时还考察了测试频率、分散相含量以及分散介质平均分子量的差别对流变性的影响. σ_c^o随测试频率的增大而变大; SiO₂质量分数越大, σ_c^o基本不变, 但增稠现象变得更明显; 与平均分子量小的PEG200体系相比, 平均分子量大的PEG400体系, σ_c^o并未发生改变, 但在增稠之前体系的粘度较低, 增稠之后体系粘度增大的幅度较大.     

水溶性聚酯浓溶液的流变特性

研究了由对苯二甲酸二甲酯、间苯二甲酸、间苯二甲酸二甲酯 5 磺酸钠与乙二醇等共缩聚合成的PET型水溶性聚酯浓水溶液 (质量浓度 3 0 % )的流变特性 .研究表明 ,溶液的表观粘度随切变速率的变化规律呈现一定的切力增稠特征 ,流动指数范围为 1 0 4～ 1 2 0之间 ;其lgηa τ曲线呈线性 ,零切粘度值为 1 5 8～3 5 2cP ,随分子量、分子结构和温度而异 ,其中分子链中间苯二甲酸乙二醇酯 5 磺酸钠链节含量对溶液粘度影响较大 ;粘流活化能因分子结构和切变速率而变 ,其值范围为 1 2 0～ 2 3 9kJ/mol.     

Energy dissipation in concentrated monodisperse colloidal suspensions of silica particles in polyethylene glycol

Highly concentrated colloidal suspensions exhibit a discontinuous shear-thickening behaviour. The transition from a low to a high viscosity state is associated to a large energy dissipation. This effect could find applications in structural damping while the viscosity increase brings added stiffness. In the present work, highly concentrated suspensions of monodisperse spherical silica particles in polyethylene glycol were selected for their strong thickening at low critical shear rates. Their damping properties were characterized by measuring the energy dissipated per cycle at low frequency (below 2 Hz) during oscillatory tests using a rheometer. The influence of parameters such as particle concentration, size and frequency was investigated. Damping was found to overcome that of benchmark elastomeric materials only in high frequencies and high strain domains.     

Rheologic Properties of a Water-Soluble Terpolymer with Vinyl Biphenyl

A water-soluble acrylamide-modified terpolymer (PAAP) with sodium 2-acrylamido-2-methylpropane sulfonate and vinyl biphenyl as the hydrophobic monomer was synthesized to obtain a polymeric thickening agent applied in middle- and low-permeability oil reservoirs. The polymer is expected to possess a low molecular weight and high solution viscosity. The steady-state consecutive shear cycles of PAAP in aqueous and brine solutions were measured, and the viscoelastic properties of PAAP solutions were investigated as a function of polymer, NaCl and sodium dodecylbenzene sulfonate (SDBS) concentrations. The aqueous PAAP solutions exhibits pseudoplastic and thixotropic behavior over the range of shear rate and shear thickening behavior at very low shear rate. The steady-state shear results show that some disrupted associating aggregates at high shear rate can be reformed during the shear reversion process and the suitable shear rate is favorable to the formation of hydrophobically associative structures in the brine solutions. Above 0.05 g⋅dL⁻¹ PAAP, aqueous PAAP solutions have predominantly elastic character over the range of angular frequency that is strengthened with increasing polymer concentration. The PAAP brine solutions exhibit predominantly elastic behavior only above 3 rad⋅s⁻¹ and a salt-thickening effect. By addition of an optimum amount of SDBS (0.5–0.8 mmol⋅L⁻¹), the complex viscosities become much higher than the dynamic viscosities, although the loss tangent values increase owing to the formation of loose associative structures.