Preparation and nonlinear optical properties of novel Y-type polyesters with highly enhanced thermal stability of second harmonic generation

3,4-Di-(2′-hydroxyethoxy)benzylidenemalononitrile (3) was prepared and condensed with terephthaloyl chloride and adipoyl chloride to yield novel Y-type polyesters (4-5) containing 3,4-dioxybenzylidenemalononitrile groups as NLO-chromophores, which constituted parts of the polymer main-chains. The resulting polymers 4-5 are soluble in common organic solvents such as acetone and N,N-dimethylformamide. They showed thermal stability up to 300 °C in thermogravimetric analysis with glass-transition temperatures obtained from differential scanning calorimetry in the range 89-91 °C. The second harmonic generation (SHG) coefficients (d₃₃) of poled polymer films at the 1064 nm fundamental wavelength were around 2.47 pm/V. The dipole alignment exhibited high thermal stability even at 10 °C higher than T_g, and there is no SHG decay below 100 °C due to the partial main-chain character of polymer structure, which is acceptable for NLO device applications.     

Novel organosoluble and colorless poly(ether imide)s based on 1,1-bis[4-(3,4-dicarboxyphenoxy)phenyl]cyclohexane dianhydride and trifluoromethyl-substituted aromatic bis(ether amine)s

A series of novel fluorinated poly(ether imide)s (IV) having inherent viscosities of 0.70-1.08 dL/g were prepared from 1,1-bis[4-(3,4-dicarboxyphenoxy)phenyl]cyclohexane dianhydride (I) and various trifluoromethyl (CF₃)-substituted aromatic bis(ether amine)s II_a-g by a standard two-step process with thermal and chemical imidization of poly(amic acid) precursors. These poly(ether imide)s showed excellent solubility in many organic solvents and could be solution-cast into transparent, flexible, and tough films. These films were essentially colorless, with an ultraviolet-visible absorption edge of 375-380 nm and a very low b^∗ value (a yellowness index) of 5.5-7.3. They also showed good thermal stability with glass-transition temperatures of 207-269 °C, 10% weight loss temperatures in excess of 474 °C, and char yields at 800 °C in nitrogen more than 62%. In comparison with analogous V series poly(ether imide)s without the -CF₃ substituents, the IV series polymers showed better solubility, lower color intensity, and lower dielectric constants.     

Colorless poly(ether-imide)s deriving from 2,2-bis[4-(3,4-dicarboxyphenoxy)phenyl]propane dianhydride(BPADA) and aromatic bis(ether amine)s bearing pendent trifluoromethyl groups

A series of poly(ether-imide)s (III) characterized by colorless, highly solubility was synthesized from 2,2-bis[4-(3,4-dicarboxyphenoxy)phenyl]propane dianhydride(BPADA) and various fluorinated aromatic diamines (I_a-h) in DMAc via polycondensation to form poly(amic acid) (II), followed by chemical (C) and thermal (H) imidization. These polymers had inherent viscosities ranging from 0.60 to 1.3 dL/g. These polyimides were highly soluble in a variety of organic solvent such as amide-type, ether-type and chlorinated solvents. Moreover, these poly(ether-imide) films were almost colorless, with an ultraviolet-visible absorption cutoff wavelength below 390 nm and low b* value (a yellowness index) of 4.6-18.0. The III series showed strength tensile of 72-101 MPa, elongation at break of 11-25%, initial modulus of 1.5-2.0 GPa. The glass transition temperature (T_g) of III_a-h were in the range of 202-267 °C, and the decomposition temperature above 493 °C and left 40-65% char yield at 800 °C in nitrogen. They had the lower dielectric constants of 3.39-3.72 (1 MHz) and moisture absorptions in the range of 0.11-0.40%.     

Molecular design, synthesis and electro-optic properties of novel Y-type polyurethanes with high thermal stability of second harmonic generation

2,4-Di-2^′-hydroxyethoxy)benzylidenemalononitrile (3) was prepared and condensed with 2,4-toluenediisocyanate and 3,3^′-dimethoxy-4,4^′-biphenylenediisocyanate to yield unprecedented novel Y-type polyurethanes (4-5) containing 2,4-dioxybenzylidenemalononitrile group as a nonlinear optical (NLO) chromophore, which constitutes a part of the polymer backbone. The resulting polyurethanes 4-5 were soluble in common organic solvents such as acetone and DMF. Polymers 4-5 showed a thermal stability up to 260 °C from thermogravimetric analysis (TGA) with differential scanning calorimetry (DSC) giving T_g values around 143-156 °C. The approximate lengths of aligned NLO-chromophores estimated from AFM images of poled polymer films were about 10 nm. The SHG coefficients (d₃₃) of poled polymer films were around 7.4 × 10⁻⁹ esu. These Poled polymers exhibited a greater thermal stability of dipole alignment even at 10 °C higher than T_g, and no SHG decay was observed below 155 °C due to the partial main chain character of the polymer structure and extensive hydrogen bonds between urethane linkage, which is acceptable for NLO device applications.     

Synthesis and polymerization of a novel perfluorinated monomer

Perfluoro(5-methylene-2,2-dimethyl-1,3-dioxolane) (1) was synthesized by utilizing a direct fluorination reaction. Compound 1 was an entirely novel monomer with difluoromethylene at position 5 on the dioxolane ring as an unprecedented polymerization site. It successfully polymerized with tetrafluoroethylene to afford copolymers, which had T_g values in the range of 60-90 °C. The content of monomer 1 in the obtained polymers was less than 20 mol%, which seemed insufficient for giving various unique properties to polymers. However, each polymer was expected to be a superior material because of their advanced thermal stability. Comparison with copolymers of 2,2-bis(trifluoromethyl)-4,5-difluoro-1,3-dioxole and tetrafluoroethylene is also discussed.     

Synthesis of photochromic diarylethene polymers for a write-by-light/erase-by-heat recording system

A functionalized styrene monomer (1a) having a photochromic diarylethene chromophore with functional properties of photocoloration, photostability of the colored state, and thermal erasion by heating was synthesized, and the polymer and copolymers of 1a were prepared by radical polymerization and copolymerization. Their polymers exhibited excellent photocoloration and rapid thermal bleaching above 150 °C in solution and in the solid state as well as the performance of the monomeric diarylethene chromophore. In addition, the colored state has a high photostability under visible room light. The diarylethene homopolymer had a glass transition temperature (T_g) as high as polystyrene. The copolymer of 1a with N-1-adamantylmaleimide exhibited extremely high T_g above 200 °C with keeping the photofunctional performance. Such photochromic polymer and copolymers with high T_g can be potentially applied to rewritable display materials and image recordings by a write-by-light/erase-by-heat system.     

Synthesis and properties of novel fluorinated polynaphthalimides derived from 1,4,5,8-naphthalenetetracarboxylic dianhydride and trifluoromethyl-substituted aromatic bis(ether amine)s

A series of novel fluorinated polynaphthalimides (PNIs) (2a-g) were synthesized from 1,4,5,8-naphthalenetetracarboxylic dianhydride (NTDA) and trifluoromethyl (CF₃)-substituted aromatic bis(ether amine)s (1a-g) by high-temperature solution polycondensation in m-cresol using isoquinoline as catalyst. Almost all the PNIs were readily soluble in polar solvents such as N-methyl-2-pyrrolidone (NMP) and N,N-dimethylacetamide (DMAc) and could be solution-cast to transparent and tough films with high tensile strengths. The PNIs exhibited high thermal stability, with glass-transition temperatures of 262-383 °C, 10% weight loss temperatures above 528 °C in nitrogen or air, and char yields at 800 °C in nitrogen higher than 50%. In comparison with analogous PNIs without the -CF₃ substituents, these fluorinated PNIs revealed an enhanced solubility and better film-forming capability.     

Substituted lithiumtrimethylsiloxysilanides LiSiRR′(OSiMe3) - Investigations of their synthesis, stability and reactivity

The reactions of the trimethylsiloxychlorosilanes (Me₃SiO)RR′SiCl (1a-h: R′ = Ph, 1a: R = H, 1b: R = Me, 1c: R = Et, 1d: R = ⁱPr, 1e: R = ^tBu, 1f: R = Ph, 1g: R = 2,4,6-Me₃C₆H₂ (Mes), 1h: R = 2,4,6-(Me₂CH)₃C₆H₂ (Tip); 1i: R = R′ = Mes) with lithium metal in tetrahydrofuran (THF) at −78 °C and in a mixture of THF/diethyl ether/n-pentane in a volume ratio 4:1:1 at −110 °C lead to mixtures of numerous compounds. Dependent on the substituents silyllithium derivatives (Me₃SiO)RR′SiLi (2b-i), Me₃SiO(RR′Si)₂Li (3a-g), Me₃SiRR′SiLi (4a-h), (LiO)RR′SiLi (12e, 12g-i), trisiloxanes (Me₃SiO)₂SiRR′ (5a-i) and trimethylsiloxydisilanes (6f^∗, 6h^∗, 6i^∗) are formed. All silyllithium compounds were trapped with Me₃SiCl or HMe₂SiCl resulting in the following products: (Me₃SiO)RR′SiSiMe₂R″ (6b-i: R″ = Me, 7c-i: R″ = H), Me₃SiO(RR′Si)₂SiMe₂R″ (8a-g: R″ = Me, 9a-g: R″ = H), Me₃SiRR′SiSiMe₂R″ (10a-h: R″ = Me, 11a-h: R″ = H) and (HMe₂SiO)RR′SiSiMe₂H (13e, 13g-i). The stability of trimethylsiloxysilyllithiums 2 depends on the substituents and on the temperature. (Me₃SiO)Mes₂SiLi (2i) is the most stable compound due to the high steric shielding of the silicon centre. The trimethylsiloxysilyllithiums 2a-g undergo partially self-condensation to afford the corresponding trimethylsiloxydisilanyllithiums Me₃SiO(RR′Si)₂Li (3a-g). (Me₃)Si-O bond cleavage was observed for 2e and 2g-i. The relatively stable trimethylsiloxysilyllithiums 2f, 2g and 2i react with n-butyllithium under nucleophilic butylation to give the n-butyl-substituted silyllithiums ⁿBuRR′SiLi (15g, 15f, 15i), which were trapped with Me₃SiCl. By reaction of 2g and 2i with 2,3-dimethylbuta-1,3-diene the corresponding 1,1-diarylsilacyclopentenes 17g and 17i are obtained.X-ray studies of 17g revealed a folded silacyclopentene ring with the silicon atom located 0.5 Å above the mean plane formed by the four carbon ring atoms.     

Characterization of cyclic and non-cyclic poly-(ether-urethane)s bio-based sugar diols by a combination of MALDI-TOF and NMR

Matrix-assisted laser desorption/ionization (MALDI) mass spectrometry and NMR spectroscopy have been applied for characterization of novel poly-(ether-urethane)s (PolyEU) based on various diols derived from starch and two diisocyanates. First, numerous polyurethanes soft and hard blocks were prepared by polyaddition of isosorbide (3), isomannide (4) or isoidide (5) with 4,4′-diphenylmethane diisocyanate (MDI) (7) or hexane-1,6-diisocyanate (HDI) (8). The polyaddition of isoidide and MDI yields 85% of polyurethane hard block with high inherent viscosity (η_inh = 0.35 dL/g) with linear chains as the main products. In the case of polyurethane based on isosorbide and MDI a large amount of cyclic compounds was formed with relatively high viscosity (η_inh = 0.29 dL/g) and good yield (77%). This polyurethane hard block presents a high glass transition temperature (T_g = 183 °C) and an excellent thermal stability until 250 °C (T_g = 77 °C of the polyurethane soft block based on isosorbide and HDI). Second, polyaddition of an aliphatic diol (6a) based on isosorbide and MDI yielded new poly-(ether-urethane) soft-hard blocks with quantitative yield (>95%). This polymer is soluble in common organic solvents and has a number-average molecular weight of 7950 Da with a polydispersity index of 1.43. The MALDI-TOF spectrum of this poly-(ether-urethane) indicated the formation of high molar fraction of cycles (Ca and Cb). The pure cyclic poly-(ether-urethane) soft-hard block presents a T_g of 141 °C.     

Ultrasonic-assisted synthesis of two new nano-structured 3D lead(II) coordination polymers: Precursors for preparation of PbO nano-structures

Nano-structures of two new Pb(II) three-dimensional coordination polymers, [Pb₂(4-pyc)₂I₂(H₂O)]_n (1), {4-Hpyc = 4-pyridinecarboxilic acid} and [Pb(3-pyc)I]_n (2), {3-Hpyc = 3-pyridinecarboxilic acid} were synthesized by sonochemical method. The new nano-structures were characterized by scanning electron microscopy, X-ray powder diffraction, IR spectroscopy and elemental analyses. Compounds 1 and 2 were structurally characterized by single crystal X-ray diffraction and are three-dimensional coordination polymers. The thermal stability of compounds 1 and 2 both their bulk and nano-size were studied by thermal gravimetric and differential thermal analyses and compared. PbO block-structures were obtained by calcination of the nano-structures of compounds 1 and 2 at 400 °C.     

Synthesis and nonlinear optical properties of novel Y-type polyimides with enhanced thermal stability of dipole alignment

2,3-Bis-(3,4-dicarboxyphenylcarboxyethoxy)-4′-nitrostilbene dianhydride (4) was prepared and reacted with 1,4-phenylenediamine, 4,4′-oxydianiline, 4,4′-diaminobenzanilide and 4,4′-(hexafluoroisopropylidene)dianiline to yield novel polyimides 5-8 containing 2,3-dioxynitrostilbenyl groups as NLO-chromophores, which constituted parts of the polymer backbones. The resulting polyimides 5-8 were soluble in polar solvents such as acetone and DMF. Polymers 5-8 showed a thermal stability up to 300 °C in TGA thermograms with T_g values obtained from DSC thermograms in the range of 135-160 °C. The SHG coefficients (d₃₃) of poled polymer films at the 1064 cm⁻¹ fundamental wavelength were around 5.26 × 10⁻⁹ esu. The dipole alignment exhibited exceptionally high thermal stability even at 30 °C higher than T_g and there was no SHG decay below 170-190 °C due to the partial main chain character of polymer structure, which was acceptable for NLO device applications.     

Synthesis and characterization of new soluble and thermally stable poly(ester-imide)s derived from N-[3,5-bis(N-trimellitoyl)phenyl]phthalimide and various bisphenols

A new dicarboxylic acid chloride (2) bearing three preformed imide rings was synthesized by treating N-(3,5-diaminophenyl)phthalimide with trimellitic anhydride followed by refluxing with thionyl chloride. A novel family of aromatic poly(ester-imide)s with inherent viscosities of 0.27-0.35 dl g⁻¹ were prepared from 2 with various bisphenols such as resorcinol (3a), hydroquinone (3b), 2,2′-dihydroxybiphenyl (3c), 4,4′-dihydroxybiphenyl (3d), bisphenol-A (3e), 2,2′-dimethyl-4,4′-dihydroxybiphenyl (3f), 1,5-dihydroxynaphthalene (3g), 2,7-dihydroxynaphthalene (3h), and 2,2′-dihydroxy-1,1′-binaphthyl (3i) by high-temperature solution polycondensation in nitrobenzene using pyridine as hydrogen chloride quencher. All of the resulted polymers were fully characterized by FT-IR and NMR spectroscopy and elemental analyses. The poly(ester-imide)s exhibited excellent solubility in some polar organic solvents. From differential scanning calorimetry, the polymers showed glass-transition temperatures between 259 and 353 °C. Thermal behaviors of the obtained polymers were characterized by thermogravimetric analysis and the 10% weight loss temperatures of the poly(ester-imide)s were found to be in the range between 451 and 482 °C in nitrogen. Furthermore, crystallinity of the polymers was estimated by means of wide-angle X-ray diffraction.     

Syntheses and characterization of different zinc(II) oxide nano-structures from direct thermal decomposition of 1D coordination polymers

Three zinc(II) nitrite coordination polymers, [Zn(4-bpdb)(NO₂)₂]_n (1), {[Zn(3-bpdb)(NO₂)]·0.5H₂O}_n (2) and [Zn(3-bpdh)(NO₂)₂]_n (3), 4-bpdb = 1,4-bis(4-pyridyl)-2,3-diaza-1,3-butadiene, 3-bpdb = 1,4-bis(3-pyridyl)-2,3-diaza-1,3-butadiene and 3-bpdh = 2,5-bis(3-pyridyl)-3,4-diaza-2,4-hexadiene} were prepared and characterized by elemental analyses and IR spectroscopy. Compound 3 was structurally characterized by single-crystal X-ray diffraction and is one-dimensional polymer with coordination environments of distorted octahedral, ZnN₂O₄. The thermal stabilities of compounds 1–3 were studied by thermal gravimetric (TG) and differential thermal analyses (DTA). Direct calcination of the compounds 1–3 at 600 °C under air atmospheres yields different morphologies of nano-sized ZnO.     

Synthesis and properties of soluble and light-colored poly(amide-imide-imide)s based on tetraimide-dicarboxylic acid (TIDA) and various aromatic diamines: TIDA from 4,4′-oxydiphthalic anhydride, 1,4-bis(4-amino-2-trifluoromethylphenoxy)benzene, and 3-aminobenzoic acid

A new tetraimide-dicarboxylic acid (TIDA) I was synthesized starting from 3-aminobenzoic acid (m-ABA), 4,4′-oxydiphthalic anhydride (ODPA), and 1,4-bis(4-amino-2-trifluoromethylphenoxy)benzene (BAFPB) at a 2:2:1 molar ratio in N-methyl-2-pyrrolidone (NMP). A series of organosoluble, light-colored poly(amide-imide-imide)s (PAII, III_a-j) was prepared by triphenyl phosphite-activated polycondensation from the tetraimide-diacid I with various aromatic diamines (II_a-j). All the polymers were readily soluble in a variety of organic solvents such as NMP, N,N-dimethyl acetamide (DMAc), dimethyl sulfoxide, and even in less polar m-cresol and pyridine. Polymer films cast from DMAc had the cutoff wavelengths between 374 and 384 nm and had the b^∗ values in the range of 14.8-30.2. Polymers III_a-j afforded tough, transparent, and flexible films, which had tensile strengths ranging from 87 to 103 MPa, elongations at break from 11% to 37%, and initial moduli from 1.9 to 2.3 GPa. The glass transition temperatures of these polymers were in the range of 242-274 °C. They had 10% weight loss temperature above 526 °C and showed the char yield more than 55% residue at 800 °C in nitrogen.     

Synthesis and properties of thermally stable and optically active novel wholly aromatic polyesters containing a chiral pendent group

5-(2-Phthalimidyl-3-methyl butanoylamino)isophthalic acid (5), as a novel diacid monomer containing phthalimide and flexible chiral groups, was prepared by the reaction of 2-phthalimidyl-3-methyl butyric acid chloride (4) with 5-aminoisophthalic acid (5AIPA) in dry N,N-dimethylacetamide (DMAc). A series of novel polyesters (PE)s containing phthalimide group was prepared by the reaction of diacid monomer 5 with several aromatic diols via direct polyesterification with the tosyl chloride/pyridine/dimethylformamide (DMF) system as a condensing agent. The resulting new polymers were obtained in good yields with inherent viscosities ranging between 0.37 and 0.61 dL g⁻¹ and were characterized with FT-IR, ¹H NMR, elemental and thermogravimetric analysis techniques. These polymers are readily soluble in amide type solvents such as DMAc, DMF, 1-methyl-2-pyrrolidone, hexamethyl triaminophosphine, dimethyl sulfoxide and protic solvents such as sulfuric acid. Thermogravimetric analysis showed that the 10% weight loss temperature in a nitrogen atmosphere was more than 345 °C, which indicates that the resulting PEs have a good thermal stability as well as excellent solubility.     

The cyclopalladation reaction of 2-phenylaniline revisited

2-Phenylaniline reacted with Pd(OAc)₂ in toluene at room temperature for 24 h in a one-to-one molar ratio and with the system PdCl₂, NaCl and NaOAc in a 1 (2-phenylaniline):1 (PdCl₂):2 (NaCl):1 (NaOAc) molar ratio in methanol at room temperature for one week to give the dinuclear cyclopalladated compounds (μ-X)₂[Pd{κ²-N2′,C1-2-(2′-NH₂C₆H₄)C₆H₄}]₂ [1a (X = OAc) and 1b (X = Cl)] in high yield. Moreover, the reaction between 2-phenylaniline and Pd(OAc)₂ in one-to-one molar ratio in acid acetic at 60 °C for 4 h, followed by a metathesis reaction with LiBr, allowed isolation of the dinuclear cyclopalladated compound (μ-Br)₂[Pd{κ²-N2′,C1-2-(2′-NH₂C₆H₄)C₆H₄}]₂ (1c) in moderate yield. A parallel treatment, but using monodeuterated acetic acid (DOAc) as solvent in the cyclopalladation reaction, allowed isolation of a mixture of compounds 1c, 1c_d1 [Pd{κ²-N2′,C1-2-(2′-NH₂C₆H₄)C₆H₄](μ-Br)₂[Pd{κ²-N2′,C1-2-(2′-NH₂C₆H₄)-3-d-C₆H₃] and 1c_d2 (μ-Br)₂[Pd{κ²-N2′,C1-2-(2′-NH₂C₆H₄)-3-d-C₆H₃}]₂ in moderate yield and with a deuterium content of ca. 60%. 1a and 1b reacted with pyridine and PPh₃ affording the mononuclear cyclopalladated compounds [Pd{κ²-N2′,C1-2-(2′-NH₂C₆H₄)C₆H₄}(X)(L)] [2a (X = OAc, L = py), 2b (X = Cl, L = py), 3a (X = OAc, L = PPh₃) and 3b (X = Cl, L = PPh₃)] in a yield from moderate to high. Furthermore, 1a reacted with Na(acac) · H₂O to give the mononuclear cyclopalladated compound 4 [Pd{κ²-N2′,C1-2-(2′-NH₂C₆H₄)C₆H₄}(acac)] in moderate yield. ¹H NMR studies in CDCl₃ solution of 2a, 2b, 3a, 3b and 4 showed that 2a and 3a presented an intramolecular hydrogen bond between the acetato ligand and the amino group, and were involved in a dynamic equilibrium with water present in the CDCl₃ solvent; and that the enantiomeric molecules of 2b and 4 were in a fast exchange at room temperature, while they were in a slow exchange for 2a, 3a and 3b. The X-ray crystal structures of 3b and 4 were determined. 3b crystallized in the triclinic space group with a = 9.9170(10), b = 10.4750(10), c = 12.0890(10) Å, α = 98.610(10)°, β = 94.034(10)° and γ = 99.000(10)° and 4 in the monoclinic space group P2₁/a with a = 11.5900(10), b = 11.2730(10), c = 12.2150(10) Å, α = 90°, β = 107.6560(10)° and γ = 90°.     

Pyrimidine based carboxylic acid terminated aromatic and semiaromatic hyperbranched polyamide-esters: synthesis and characterization

Carboxylic acid terminated aromatic and semiaromatic hyperbranched polyamide-esters (HBPAEs) containing pyrimidine moieties were prepared by polycondensation of 4-hydroxy-2,6-diaminopyrimidine (CBB′) to a double molar ratio of various diacid chlorides (A₂) without any catalyst. The products were soluble in organic solvents, such as N,N-dimethylformamide, N-methyl-2-pyrrolidone and displayed glass transition temperature (T_g) between 180 and 244 °C. The polymerization products have been investigated with FTIR, ¹H and ¹³C NMR analyses and the degree of branching was higher than 60%. Amorphous polymers had inherent viscosity (η_inh) ranging between 0.21-0.28 dL/g and had excellent thermal stability with 10% weight loss at 346-508 °C.     

Synthesis, characterization, and ethylene polymerization behavior of [(RR′-admpzp)2Ti(OPr)2] complexes (RR′-admpzp = 1-dialkylamino-3-(3,5-dimethyl-pyrazol-1-yl)-propan-2-olate)

[(RR′-admpzp)₂Ti(OPrⁱ)₂] complexes (2a-c), synthesized from reaction of Ti(OPrⁱ)₃Cl (0.5 equiv) with 1-dialkylamino-3-(3,5-dimethyl-pyrazol-1-yl)-propan-2-ol compounds in the presence of triethylamine (0.5 equiv), are pseudo-octahedral with each RR′-admpzp ligand κ²-O,N(pyrazolyl) coordinated to the titanium center. In solution, 2a-c adopt isomeric structures that are in dynamic equilibrium. At 23 °C, 2a-c/1000 MAO catalyst systems furnished high molecular weight polymers with narrow molecular weight distributions (M_w/M_n = 2.7-2.8). At 100 °C, 2a-c/MAO catalyst systems exhibited increased polymerization activity and 2c/1000 MAO system furnished high molecular weight polyethylene with a molecular weight distribution (M_w/M_n = 2.1) that is close to that found for single-site catalysts.     

Thermal hydrosilylation of olefin with hydrosilane. Preparative and mechanistic aspects

The reaction of trichlorosilane (1a) at 250 °C with cycloalkenes, such as cyclopentene (2a), cyclohexene (2b), cycloheptene (2c), and cyclooctene (2d), gave cycloalkyltrichlorosilanes [C_nH_2n−1SiCl₃: n = 5 (3a), 6 (3b), 7 (3c), 8 (3d)] within 6 h in excellent yields (97-98%), but the similar reactions using methyldichlorosilane (1b) instead of 1a required a longer reaction time of 40 h and afforded cycloalkyl(methyl)dichlorosilanes [C_nH_2n−1SiMeCl₂: n = 5 (3e), 6 (3f), 7 (3g), 8 (3h)] in 88-92% yields with 4-8% recovery of reactant 2. In large (2, 0.29 mol)-scale preparations, the reactions of 2a and 2b with 1a (0.58 mol) under the same condition gave 3a and 3b in 95% and 94% isolated yields, respectively. The relative reactivity of four hydrosilanes [HSiCl_3−mMe_m: m = 0-3] in the reaction with 2a indicates that as the number of chlorine-substituent(s) on the silicon increases the rate of the reaction decreases in the following order: n = 3 > 2 > 1 ? 0. In the reaction with 1a, the relative reactivity of four cycloalkenes (ring size = 5-8) decreases in the following order: 2d > 2a > 2c > 2b. Meanwhile linear alkenes like 1-hexene undergo two reactions of self-isomerization and hydrosilylation with hydrosilane to give a mixture of the three isomers (1-, 2-, and 3-silylated hexanes). In this reaction, the reactivity of the terminal 1-hexene is higher than the internal 2- and 3-hexene. The redistribution of hydrosilane 1 and the polymerization of olefin 2 occurred rarely under the thermal reaction condition.     

Synthesis and properties of phthalonitrile-terminated oligomeric poly(ether imide)s containing phthalazinone moiety

Three novel series of soluble and curable phthalonitrile-terminated oligomeric poly(ether imide)s containing phthalazinone moiety were synthesized from an excess amount of three dianhydrides and phthalazinone-based diamine, followed by reacting with 4-(3-aminophenoxy)phthalonitrile (APPh) in a two-step, one-pot reaction, respectively. The phthalonitrile oligomers containing phthalazinone moiety were cured in the presence of 4,4′-diaminodiphenylsulfone (DDS). The oligomers and the crosslinked polymers were characterized by DSC, FT-IR and elemental analysis. These phthalonitrile oligomers containing phthalazinone groups were found to be soluble in some aprotic solvents, such as chloroform, pyridine, m-cresol and N-methyl-2-pyrrolidone (NMP). The crosslinked polymers were insoluble in all solvents. The thermal properties of the oligomers and the crosslinked polymers were evaluated using DSC and TGA analysis. The phthalonitrile oligomers showed high glass transition temperatures (T_gs) in the range of 214-256 °C and high decomposition temperatures with 10% weight loss (T_d10%) ranging from 523 to 553 °C. The crosslinked polymers showed excellent thermal stability with the 10% weight loss temperatures ranging from 543 to 595 °C, but did not exhibit a glass transition temperature upon heating to 350 °C.