脂肪族聚酰胺热膨胀行为的研究

通过热膨胀测试,示差扫描量热分析(DSC)、广角X射线衍射(WAXD)与傅里叶变换红外光谱(FTIR)等方法研究了4种脂肪族聚酰胺玻璃化转变温度(Tg)、结晶行为以及氢键强度对热膨胀行为的影响,探索了影响脂肪族聚酰胺热膨胀的本质.DSC和X射线衍射结果表明,聚酰胺中结晶部分的热膨胀系数要低于无定形部分,但聚酰胺的熔融温度和结晶度对热膨胀的影响不够明确.相比较其它脂肪族聚酰胺,聚酰胺56(PA56)具有较高的玻璃化转变温度和较低的亚甲基/酰胺基(CH2/CONH)比例,表现出较低的热膨胀系数.研究发现,在相同条件下制备的脂肪族聚酰胺体系中,CH2/CONH比例或Tg与热膨胀系数具有明显的线性关系,随着CH2/CONH比例的降低或Tg的升高,热膨胀系数显著减小.FTIR的结果表明,聚酰胺分子链间的氢键密度和氢键强度随温度升高衰减的程度是影响其热膨胀行为的关键因素.     

Synthesis and characterization of polyamides containing pendant pentadecyl chains

A new aromatic diacid monomer viz., 4-(4′-carboxyphenoxy)-2-pentadecylbenzoic acid was synthesized starting from cardanol and was characterized by FTIR, ¹H- and ¹³C NMR spectroscopy. A series of new aromatic polyamides containing ether linkages and pendant pentadecyl chains was prepared by phosphorylation polycondensation of 4-(4′-carboxyphenoxy)-2-pentadecylbenzoic acid with five commercially available aromatic diamines viz., 1,4-phenylenediamine, 4,4′-oxydianiline, 4,4′-methylenedianiline, 1,3-phenylenediamine, and 4,4′-(hexafluoroisopropylidene)dianiline. Inherent viscosities of the polyamides were in the range 0.45-0.66 dL/g in N,N-dimethylacetamide at 30 ± 0.1 °C. The introduction of ether linkages and pendant pentadecyl chains into polyamides led to an enhanced solubility in N,N-dimethylacetamide and 1-methyl-2-pyrrolidinone at room temperature or upon heating. The polyamides could be solution-cast into tough, flexible and transparent films from their N,N-dimethylacetamide solution. Wide angle X-ray diffraction patterns exhibited broad halo indicating that the polymers were essentially amorphous in nature. X-Ray diffractograms also displayed a diffuse to sharp reflection in the small-angle region (2θ = ∼2-5°) for the polyamides characteristics of formation of loosely to well-developed layered structure arising from packing of flexible pentadecyl chains. The glass transition temperature observed for the polyamides was in range 139-189 °C. The temperature at 10% weight loss (T₁₀), determined by TGA in nitrogen atmosphere, of the polyamides was in the range 425-453 °C indicating their good thermal stability.     

Synthesis and characterization of novel even-odd nylons based on undecanedioic acid

A series of novel even-odd nylons were synthesized through step-heating melting-polycondensation of undecanedioic acid with various diamines. The synthesized polyamides were characterized comprehensively by means of elements analysis, intrinsic viscosity, Fourier transform infrared (FTIR) spectroscopy, nuclear magnetic resonance (NMR), Raman spectra, thermogravimetry analysis (TGA) and differential scanning analysis (DSC). The obtained products except nylons 4 11 and 2 11 have intrinsic average molecular weights ranging from 1.3 × 10⁴ to 2.5 × 10⁴. Nylons 4 11 and 2 11 have intrinsic average molecular weights of 8400 and 7200, respectively. The melting temperatures of this series of even-odd nylons decrease with declining the concentration of hydrogen bonds. Furthermore, the dynamic mechanical analysis (DMA) was performed for nylons 12 11, 10 11, 8 11 and 6 11. The glass transition temperatures of nylons 12 11, 10 11, 8 11 and 6 11 are in the range of 40.1-45.7 °C.     

Synthesis and properties of new soluble N-phenyl–substituted aromatic-aliphatic and all aromatic polyamides derived from 4,4′-dianilinobiphenyl

New N-phenylated aromatic-aliphatic and all aromatic polyamides were prepared by the high-temperature solution polycondensation of 4,4′-dianilinobiphenyl with both aliphatic (methylene chain lengths of 6–11) and aromatic dicarboxylic acid chlorides. All of the aromatic-aliphatic polyamides and the wholly aromatic polyamides exhibited an amorphous nature and good solubility in amide-type and chlorinated hydrocarbon solvents, except for those aromatic polyamides containing p-oriented phenylene or biphenylylene linkages in the backbone; the latter were crystalline and insoluble in organic solvents except m-cresol. The N-phenylated aromatic-aliphatic polyamides and aromatic polyamides had glass transition temperatures in the range of 79–116°C and 207–255°C, respectively, and all the polymers were thermally stable with decomposition temperatures above 400°C in air. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2193–2200, 1998     

Crystallizability and thermal properties of phosphorus-containing polyamides

Bis(2-carb-n-butoxyethyl)methylphosphine oxide was prepared and condensed with 1,2-diaminoethane, 1,6-diaminohexane, 1,8-diaminooctane, 1,10-diaminodecane, and 1,12-diaminododecane to form polyamides with an increasing number of methylene groups between the amide moieties. Polyamides made from the 1,10- and 1,12-diaminoalkanes were shown by x-ray and DSC to be semicrystalline, while those based on the 1,6- and 1,8-diaminoalkanes were amorphous to x-ray and revealed no first-order transitions. The repeat distances of the crystalline polymers were determined, and an extended planar zigzag conformation was excluded as a possible conformation for these polymers. The thermal stability of the phosphorus-containing polyamides, in both oxygen and nitrogen, was studied by TGA and the results were correlated with the chemical structure.     

Soluble and thermally stable polyamides bearing 1,1′-thiobis(2-naphthoxy) groups

A new-type of sulfide containing diacid (1,1′-thiobis(2-naphthoxy acetic acid)) was synthesized from 2-naphthol in three steps. Reaction of 2-naphthol with sulfur dichloride afforded 1,1′-thiobis(2-naphthol) (TBN). 1,1′-Thiobis(2-naphthoxy acetic ester) (TBNAE) was successfully synthesized by refluxing the TBN with methylcholoroacetate in the presence of potassium carbonate. The related diacid was synthesized by basic solution reduction of TBNAE. The obtained diacid was fully characterized and used to prepare novel thermally stable poly(sulfide ether amide)s via polyphosphorylation reaction with different aromatic diamines. The properties of these new polyamides were investigated and compared with similar polyamides. These polyamides showed inherent viscosities in the range of 0.39-0.87 dL g⁻¹ in N,N-dimethylacetamide (DMAc) at 30 °C and at a concentration of 0.5 g dL⁻¹. All the polyamides were readily soluble in a variety of polar solvents such as DMAc and tetrahydrofuran (THF). These polyamides showed glass transition temperature (T_g) between 241-268 °C. Thermogravimetric analysis measurement revealed the decomposition temperature at 10% weight loss (T₁₀) ranging from 441- 479 °C in argon atmosphere.     

尼龙-6 18的晶型转变研究

以偶偶尼龙-6 18为例, 通过示差扫描量热分析(DSC), 广角X射线衍射(WAXD)与傅里叶变换红外光谱(FTIR)等方法研究了其Brill转变的过程, 探索了脂肪族聚酰胺的晶型转变的本质. X射线衍射结果表明， 随着温度的升高, 尼龙-6 18由三斜晶系转变为假六方晶型, 同时其DSC曲线上出现一个较宽的吸热峰. 红外光谱结果表明, 在其晶型转变过程中, 晶体内氢键强度逐渐减弱, 与酰胺键相连的C—C和C—N键发生扭曲. 酰胺基团之间的亚甲基链段的振动逐渐增强, 部分亚甲基单元由反式构象变成旁式构象, 最后整齐排列的亚甲基链段逐渐变得无序化.     

含异丙基及三氟甲基可溶性聚酰胺的合成及性能研究

以含异丙基和三氟甲基结构二胺单体3,3′-二异丙基-4,4′-二胺基苯基-4″-三氟甲基甲苯(PATFT)与萘-1,4-二甲酸、间苯二甲酸和4,4-二苯醚二甲酸3种二酸通过膦酰化反应制备一系列新型可溶性聚酰胺,其相对分子量在3.8×104~9.6×104之间.结果表明,该聚合物具有优异的溶解性能,常温不仅能溶解于N-甲基吡咯烷酮(NMP)、N,N-二甲基乙酰胺(DMAc)、N,N-二甲基甲酰胺(DMF)等高沸点有机溶剂,在加热条件下甚至能较好的溶解在四氢呋喃、氯仿、二氯甲烷等低沸点溶剂中;突出的光学性能,截止波长范围在322~350 nm,80%的透过率波长范围为378~403 nm;良好的热学性能,玻璃化转变温度(Tg)范围在213~220?C,氮气氛围下5%和10%热失重温度范围分别为453~458?C和470~482?C.聚合物薄膜具有优异的机械性能,拉伸强度、杨氏模量、断裂伸长率分别对应为68~97 MPa,1.9~2.9 GPa,14.8%~16.7%.广角X-射线图谱表明聚合物为无定形态结构.     

Liquid crystalline and photoactive poly[4,4′-stilbeneoxy]alkylbiphenylphosphates

A series of liquid crystalline and photoactive polymers were synthesized from biphenylphosphorodichloridate with various 4,4′-bis(m-hydroxyalkyloxy)stilbenes (m = 2, 4, 6, 8, 10) in chloroform by solution polycondensation method using an acid scavenger. The resultant polymers were characterized by inherent viscosity, FT-IR, ¹H, ¹³C and ³¹P NMR spectroscopies. The liquid crystalline (LC) properties were studied using HOPM and DSC and it was inferred that out of the five polymers synthesized, higher methylene chain containing polymers (m = 6, 8, 10) exhibited LC properties. Thermogravimetric analysis revealed that all the polymers were stable in between 290 and 367 °C and underwent degradation thereafter. The thermal stability and char yield of the polymers decreased with increase in flexible methylene chain. The photochemical properties of these polymers were investigated by UV and fluorescence spectroscopy. Crosslinking proceeds via 2π-2π cycloaddition reaction of the -CHCH- of the stilbene moieties. The rate of crosslinking increases with increase in methylene chain length in the polymer backbone. The fluorescence spectra showed that the longer methylene spacer containing polymers exhibited larger red-shifts than the shorter spacer containing polymers.     

Investigation on the Brill transition of polyamide 618

The Brill transition of even-even polyamide 618 was investigated using differential scanning calorimetry (DSC), temperature-dependent wide angle X-ray diffraction (WAXD) and Fourier transform infrared (FTIR). The X-ray diffraction results indicate that the melt-crystallized sample of polyamide 618 transforms from the triclinic unit cell to the pseudo-hexagonal phase in the range of 120–180°C. In this range, the thermograph of polyamide 618 presents a broad endothermal peak. From the FTIR spectra, it was found that during the transition process of polyamide 618, the intensity of the intra-sheet hydrogen bonds becomes weak. At the same time, the CH₂-amide bonds twist, and the all-trans conformation of methylene sequences is disordered by inserting the gauche conformation. The CH₂ segments are in a mobile state because of the enhanced stretching and twisting vibrations of the C-CO and C-N bonds. Translated from Chemical Journal of Chinese Universities, 2006, 27 (2) (in Chinese)     

Sulfide and sulfoxide based poly(ether-amide)s: Synthesis and characterization

Two new diacid monomers, 2,2′-sulfide bis(4-methyl phenoxy acetic acid) and 2,2′-sulfoxide bis(4-methyl phenoxy acetic acid) were successfully synthesized by refluxing the 2,2′-sulfide bis(4-methyl phenol) and 2,2′-sulfoxide bis(4-methyl phenol) with chloroacetonitrile in the presence of potassium carbonate, and subsequent basic reduction. Two novel series of poly(sulfide-ether-amide)s and poly(sulfoxide-ether-amide)s with aliphatic units in the main chain were prepared from diacids with various diamines.The polyamides were obtained in quantitative yields and their inherent viscosities were in the range of 0.43-0.89 dl g⁻¹ at a concentration of 0.5 g dl⁻¹ in N,N-dimethylacetamide (DMAc) solvent at 25 °C. They showed good thermal stability. The temperature for 10% weight loss in argon atmosphere was in the range of 350-415 °C. The polymers showed glass transition temperatures between 228 and 261 °C. Almost all of the polyamides were readily soluble in a variety of polar solvents such as N-methyl-2-pyrrolidone (NMP) and dimethyl sulfoxide (DMSO).     

Study of kinetics of thermal degradation and to determine the activation energies of polyamides based on s-triazine

A series of ten polyamides was prepared by the high-temperature polycondensation of 4,6-bis(N-(4-(benzoylchloride)amino))-2-(N-phenyl- piperazin-1-yl)-1,3,5-triazine with different aromatic and aliphatic diamines. The synthesized polyamides were analyzed by physico-chemical properties such as solubility, density, viscosity etc. The structure of prepared polyamides was evaluated by ¹H NMR and FTIR spectrum. Thermogravimetric analysis used to study the kinetics of thermal degradation of some synthesized polyamides. Broido, Horowitz & Metzger, Coats Redfern and Chan et al. models were applied to respective thermograms to determine the activation energy (E_a). Activation energy data shows that the polyamides obtained from aromatic diamine has greater stability than the polyamides obtained from aliphatic amine.     

Polyamides based on diamines and N,N′-dimethyldiamines derived from biphenol

Aromatic-aliphatic polyamides containing a biphenyl mesogen were prepared by both interfacial and solution polymerization reactions. Substitution of the amide nitrogen with methyl groups yielded polymers with significantly different properties than the unsubstituted polyamides. The methyl-substituted polyamides had improved thermal stability, significantly lower meltin temperatures, and greater solubility in common solvents. Copolyamides were also synthesized which contained different flexible spacer units that varied in the number of methylene groups. No evidence for the presence of liquid crystalline phases could be obtained in either the unsubstituted polyamides or polyamides containing N-methylated amide units. © 1994 John Wiley & Sons, Inc.     

Crystalline transition of polyamide‐10,20 investigated by in situ Fourier transform infrared spectroscopy

Real‐time Fourier transform infrared spectroscopy was used to investigate the crystalline transition of even–even polyamide‐10,20. During the crystalline transition, the intensity of the hydrogen bonds became weak, the twisting of the C? CO and C? N bonds improved, and the gauche conformation of the CH₂ sequences increased, along with the strengthening of the vibration of the methylene units. The ordered stacking of methylene segments with the trans‐zigzag conformation gradually became disordered by the insertion of the gauche conformation upon heating. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4017–4022, 2004     

Naphthalene-ring containing diamine and resulting thermally stable polyamides

A new naphthalene-ring containing diamine, bis-[4-(5-amino-naphthalene-1-yloxy)-phenyl]-methanone was prepared from reaction of 5-amino-1-naphthol with 4,4′-dichlorobenzophenone in the presence of K₂CO₃. A series of novel polyamides were prepared by direct polycondensation of the diamine with various commercially available diacid chlorides including terephthaloyl chloride, isophthaloyl chloride, adipoyl chloride, and sebacoyl chloride. All the synthesized polyamides showed good solubility in amide type solvents such as N-methyl-2-pyrrolidone, N,N-dimethylacetamide, and N,N-dimethylformamide and they exhibited inherent viscosities in the range of 0.44-0.52 dL/g. According to the DMTA analysis, the glass transition temperatures of the polyamides were found to be 131-187 °C. Thermogravimetric analysis indicated that the polymers were stable up to 190 °C and the 10% weight loss temperatures were recorded in the range of 350-418 °C in air atmosphere.     

Crystalline structure of sequential poly(ester amide)s derived from glycolic acid, 1,6‐hexanediamine,and even aliphatic dicarboxylic acids

Basic structural data of two sequential poly(ester amide)s derived from glycolic acid, 1,6‐hexanediamine, and adipic acid or dodecanodioic acid have been determined by means of X‐ray and electron diffraction patterns from fibers and single crystals. Chain‐folded lamellar crystals were obtained by isothermal crystallization from diol or glycerine solutions, and the crystalline habit was investigated by real space electron microscopy. Polyethylene decoration techniques were applied to evaluate the regularity of the folding surfaces. Spherulites prepared from evaporation of formic acid solutions were also studied. The two sequential poly(ester amide)s crystallized according to triclinic and monoclinic unit cells, in which the a crystallographic parameter was close to the typical distance between hydrogen‐bonded chains. Projections viewed down the chain axis revealed differences in the packing mode since oblique and rectangular cells were found for the adipic acid and dodecanodioic acid derivatives, respectively. Both structures can be envisaged as a stacking of hydrogen‐bonded sheets although clear differences concerning the shift between consecutive sheets and the number of layers comprising the unit cell were found. The large unit cells that have been deduced seem to be a consequence of the different packing preferences of the diester and diamide moieties. Both polymers have a molecular conformation that deviates from the all‐trans conformation typical of aliphatic polyamides and polyesters with a large number of methylene groups. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 194–206, 2009     

Helical structures of N-alkylated poly(p-benzamide)s

Poly(p-benzamide)s 1 bearing a chiral side chain on the nitrogen atom were synthesized by chain-growth polycondensation methodology. The polyamides exhibited well-defined molecular weights with narrow polydispersities. Solutions of the polyamides in several organic solvents (CH(3)CN, CHCl(3), and CH(3)OH) showed dispersion type CD signals characteristic of coupled-oscillator and much larger as compared with the corresponding monomer. The CD signals were dependent on the temperature and molecular weight of the polyamides but independent of the solvent, as far as examined. An exciton model analysis of the absorption and CD spectra provided a clear-cut picture for the secondary structure of these polyamides in solution that the N-alkylated poly(p-benzamide)s possess a right-handed helical conformation ((P)-helix). In the solid states, the results of X-ray crystallographic analysis of 4-(methylamino)benzoic acid oligomers substantiated that they have a helical conformation with three monomer units per turn.     

Hydrolytic degradation of carbohydrate-based polyamides of the AABB type derived from l-arabinose and d-xylose

The hydrolytic degradation of a series of aregic carbohydrate-based polyamides derived from l-arabinose and d-xylose is described. These polyamides are those that are fully sugar-based (PA-SuSu), those derived from aldaric acids and polyalkylene diamines (PA-mSu), and those derived from diamine sugars and polyalkylene dicarboxylic acids (PA-Sun). Their physical properties and crystal structures depend on their constitution and the configuration of the carbohydrate-based moiety. The feasibility of the hydrolysis of these polyamides was, in general, related with such structural properties. Thus, the fully sugar-based PA-SuSu were amorphous, water-soluble materials, and were hydrolysed in water at 70 °C. PA-mSu were crystalline and more resistant to hydrolysis — they were degraded at pH 2 and 70 °C [T_g(s) 60-90 °C]. PA-Sun were amorphous and highly hygroscopic materials — they were hydrolysed in water at 37 °C [T_g(s) 25-40 °C].     

Solid state crystalline and liquid crystalline structure of semifluorinated 1-bromoalkane compounds

A series of semifluorinated 1-bromoalkane (SFBA) mesogens have been synthesized and characterized to better understand their solid state crystalline and liquid crystalline structures. In the solid state, the local conformation of the fluorocarbon segments becomes disordered once the fluorocarbon chain reaches a length above eight CF units. This is evident from the pronounced decrease of molar melting enthalpy. An increasing amount of helix and helix reverse conformations and increasingly disordered packing can also be observed with each addition of a fluorocarbon segment. X-ray diffraction peaks in the small angle region can be indexed by a tilted, two dimensional layered (herring bone) structure. The crystal structure is similar to a type of plastic crystal in which the amphiphilic character is clear, because the two segments of fluorocarbon and hydrocarbon are almost immiscible. Heating of F(CF2)12(CH2)10Br leads to a transition from plastic crystal to smectic B, as revealed by time-resolved XRD and FTIR analysis. At this solid-to-liquid transition temperature, conformational analysis confirmed an onset of the CH2 gauche conformation within the hexagonal lattice, most likely due to changes occurring in the hydrocarbon segment, and a sudden increase of helix defects along the fluorocarbon segment. The disordered helix rigid-rod structure of the fluorocarbon segment and its poor compatibility with the hydrocarbon segment play an important role in the crystalline solid and liquid crystalline structures.     

Novel soluble fluorinated aromatic polyamides derived from 2-(4-trifluoromethylphenoxy)terephthaloyl chloride with various aromatic diamines

A series of novel fluorinated aromatic polyamides derived from a new monomer, 2-(4-trifluoromethylphenoxy)terephthaloyl chloride (TFTPC), with various aromatic diamines were synthesized and characterized. The polyamides were obtained in high yields and moderately high inherent viscosities ranging from 1.07 to 1.16 dL/g. All the polyamides were amorphous and readily soluble in many organic solvents, such as N-methyl-2-pyrrolidinone (NMP), N,N′-dimethylacetamide (DMAc), N,N′-dimethylformamide (DMF) and dimethyl sulfoxide (DMSO), and could afford flexible and tough films via solution casting. The cast films exhibited good mechanical properties with tensile strengths of 82.8-107.3 MPa, elongation at break of 4.1-7.2%, and tensile modulus of 2.26-3.95 GPa. These polyamide films also exhibited good thermal stability with the glass transition temperature of 222-294 °C, the temperature at 5% weight loss of 442-472 °C in nitrogen. They exhibited low dielectric constants ranging from 3.25 to 3.39 (1 MHz), low moisture absorption in the range of 1.32-2.45%, high transparency with an ultraviolet-visible absorption cut-off wavelength in the 330-371 nm range, and excellent electrical properties.