Monosized cationic nanoparticles prepared by emulsifer-free emulsion polymerization

Monosized poly(styrene/N-[3-(dimethylamino)propyl]methacrylamide/poly(ethylene glycol) ethyl ether methacrylate) [poly(St/PEG-EEM/DMAPM)] cationic nanoparticles were synthesized by emulsifier-free emulsion polymerization conducted in the presence of a cationic initiator, 2,2-azobis(2-methylpropionamidine) dihydrochloride (APDH or V-50). Particle sizes and surface charge densities were measured with a Zeta Sizer. The structure of the terpolymers was determined by Fourier transform IR and ¹H NMR spectroscopies. The amounts of the main monomer (St), cationic comonomer (DMAPM), stabilizer (PEG-EEM), and initiator (APDH), and the water-to-monomer phase ratio were all effective on both the average size and the surface charge of the nanoparicles. The average particle size was in the range 75–400 nm depending on the recipe applied; it decreased on increasing the amount of DMAP or PEG-EEM or the water-to-monomer phase ratio in the feed, while it increased with increasing St or APDH content. These nanoparticles were quite monodisperse with a polydispersity index of 1.008–1.14.     

Nanopore microspheres prepared by a cationic surfmer in the miniemulsion polymerization of styrene

A polymerizable cationic quaternary ammonium surfactant (CQAS) based on 2‐(dimethylamino)ethyl methacrylate (DMAEMA) was successfully synthesized via quaternization reaction. The product was characterized by FTIR and ¹H NMR spectroscopy, and its critical micelle concentration (CMC) was obtained by surface tension measurement. The surfmer acted well as comonomer and surfactant to stabilize monomer droplets during miniemulsion polymerization. To identify whether this system undergoes miniemulsion nucleation mechanism, surface tension, particle size, and N_droplet/N_particle of the system were also measured. The effect of concentration and counter‐ion of the surfmer, and pH value of the system were systematically investigated by kinetic analysis and dynamic light scattering (DLS). The resulting nanopore microspheres were observed by transmission electron micrograph (TEM) and field emission scanning electron micrograph (FESEM) and showed the nanopore morphology with reasonable stability. Another cationic surfactant cetyltrimethylammonium bromide (CTAB) was used for comparative studies. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5800–5810, 2007     

Preparation of multihollow polystyrene particles by seeded emulsion polymerization using seed particles with incorporated nonionic emulsifier: effect of temperature

Seeded emulsion polymerizations of styrene using polystyrene (PS) seed particles with incorporated nonionic emulsifier were carried out at 40 and 70 °C to investigate the influence of temperature during the polymerization process including the swelling step of the seed particles with monomer on the formation of multihollow PS particles. An increase in the temperature during the polymerization process caused an increase in the rate of coalescence (i.e., the degree of coalescence at any given time) of the small water domains in the inside. After the coalescence proceeded excessively, the water domains were eventually discharged from the particles to the medium, resulting in nonhollow particles. The results show that it is important for the preparation of the multihollow PS particles to control the coalescence of a lot of small water domains inside the seed particles with the incorporated nonionic emulsifier, and strongly support the formation mechanism previously proposed. Part CCCXX of the series “Studies on Suspension and Emulsion”.     

The modification and characterization of maleic anhydride-styrene-methyl metacrylate terpolymer by poly(ethylene adipate)

In this study, the functionality of maleic anhydride was utilized in the maleic anhydride-styrene-methyl metacrylate (MAStMMA) terpolymer. First, the polyester of poly(ethylene adipate), PEA, polycondensation copolymer was synthesized from ethylene glycol and adipic acid monomers. PEA was then modified on its maleic anhydride units in the MAStMMA terpolymer which has been synthesized previously. This modified copolymer was characterized by FTIR (Fourier Transform Infrared spectroscopy). The viscosimetric and thermomechanical characterization of MAStMMA terpolymer and its modified copolymer were also performed and the results were compared. The modified copolymer obtained was found to be more elastic and more soluble, and had lower viscosity and density.     

Synthesis and characterization of novel polymer-drug conjugate based on the anhydride containing copolymer as a potential method for drug carrier

5-Fluorouracil (5FU) is in clinical use as an antitumor agent for the treatment of several types of solid tumors and cancers. However, development of drug resistance within the tumor cells and side effects has been a major limitation for the clinical use of 5FU. Preparation polymer-5FU conjugation is a promising potential antitumor drug and alternative pathway that could be used to treatment of cancer. For this purpose, water soluble poly(maleic anhydride-alt-N-vinyl pyrrolidone)[Poly(MA-alt-NVP)] is synthesized via charge transfer complex (CTC) copolymerization with benzoyl peroxide as an initiator at 80°C under nitrogen atmosphere. CTC mechanism is formed between through MA and NVP by determined using Uv-vis spectroscopy. Molar absorption coefficient (?^AD) and equilibrium constant (K^AD) of the complex are determined by Scott equation. The results obtained from indicate that copolymerization of MA:NVP system is preceded via alternating mechanism. The compositions of synthesized copolymers are also investigated by elemental analysis and the reactivity ratios of these monomers are calculated by using the elemental analysis data through Kelen-Tüdös, Mayo-Lewis, Fineman-Ross and Inverted Fineman-Ross equations. For preparation of polymer-drug conjugate, chemical modification is employed between the copolymer and 5FU. Polymer-drug conjugate and conjugation mechanism are enlightened by ATR-FTIR, NMR, HR-Raman and XRD methods.     

Synthesis of a novel phosphate‐containing highly transparent PMMA copolymer with enhanced thermal and flame retardant properties

A novel poly(methyl methacrylate) (PMMA)‐based copolymer (PMMA‐co‐BDPA) rich in aromatic rings was synthesized via radical copolymerization between a phosphorus‐containing acrylic monomer (BDPA) and methyl methacrylate (MMA). UV‐vis spectroscopy demonstrated that the copolymer had high transparency. Thermogravimetric analysis (TGA) and a differential scanning calorimeter (DSC) were used to test the thermal properties of the composites. Additionally, the PMMA‐co‐BDPA‐15 copolymer exhibited a 23% increase in the limited oxygen index (LOI) value. A cone calorimeter test indicated that the peak heat release rate (pk‐HRR) of PMMA‐co‐BDPA was reduced by 29.2% compared with that of pure PMMA, and the carbon yield of burning was obviously increased. The combined test results demonstrated that the prepared copolymer material had good transparency, thermal stability, and flame retardancy.     

New antibacterial cationic surfactants prepared by atom transfer radical polymerization

Efficient antibacterial surfactants have been prepared by the quaternization of the amino groups of poly(ethylene‐co‐butylene)‐b‐poly[2‐(dimethylamino)ethylmethacrylate] (PEB‐b‐PDMAEMA) diblock copolymers by octyl bromide. The diblock copolymers have been synthesized by ATRP of 2‐(dimethylamino)ethylmethacrylate (DMAEMA) initiated by an activated bromide‐end‐capped poly(ethylene‐co‐butylene). In the presence of CuBr, 1,4,7,10,10‐hexamethyl‐triethylenetetramine (HMTETA), and toluene at 50 °C, the initiation is slow in comparison with propagation. This situation has been improved by the substitution of CuCl for CuBr, all the other conditions being the same. Finally, the addition of an excess of CuCl₂ (deactivator) to the CuCl/HMTETA catalyst is very beneficial in making the agreement between the theoretical and experimental number‐average molecular weights excellent. The antibacterial activity of PEB‐b‐PDMAEMA quaternized by octyl bromide has been assessed against bacteria and is comparable to the activity of a commonly used disinfectant, that is, benzalkonium chloride. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1214‐1224, 2006     

Flow injection determination of cationic surfactants by using N-bromosuccinimide and N-chlorosuccinimide as new oxidizing agents for luminol chemiluminescence

Two highly sensitive chemiluminescence (CL) systems are described. The method is based on the CL generated during the oxidation of luminol by N-bromosuccinimide (NBS) and N-chlorosuccinimide (NCS) in alkaline medium. The emission intensity is reduced by the presence of some surfactants at concentrations lower than critical micelle concentration (cmc).A new, simple, rapid and selective flow injection CL method for the determination of cationic surfactants such as dodecyltrimethylammonium bromide (DTAB), cetyltrimethylammonium bromide (CTAB) and cetylpyridinium chloride (CPC) is proposed. Their determinations are based on the reducing effect on the emission intensity of NBS-luminol and NCS-luminol chemiluminescent reactions. The effect of analytical and flow injection analysis (FIA) variables on these CL systems and on the determination of the cationic surfactants are discussed. The optimum parameters for the determination of cationic surfactants were studied and were found to be the following: luminol, 1×10⁻⁶ M; NBS and NCS both, 5×10⁻² M; NaOH, 5×10⁻² M and flow rate, 3.5 ml min⁻¹.     

RAFT radical copolymerization of beta‐pinene with maleic anhydride and aggregation behaviors of their copolymer in aqueous solution

RAFT copolymerization of beta‐pinene and maleic anhydride was successfully achieved for the first time, using 1‐phenylethyl dithiobenzoate as chain transfer agent in a mixed solvent of tetrehydrofuran and 1.4‐dioxane (1:9, v/v) at a feed molar ratio of beta‐pinene to maleic anhydride as 3:7, and the alternating copolymer was prepared with predetermined molecular weight and narrow molecular weight distribution. Furthermore, using former alternating copolymer as a macro‐RAFT agent, block copolymer poly(beta‐pinene‐alt‐maleic anhydride)‐b‐polystyrene was synthesized in a chain extending with styrene. Hydrolysis of this block copolymer under acidic conditions formed a new amphiphilic block copolymers poly(beta‐pinene‐alt‐maleic acid)‐b‐polystyrene whose self‐assembly behaviors in aqueous solution at different pH were investigated through SEM and DLS. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1422–1429     

Graft copolymer composed of cationic backbone and bottle brush-like side chains as a physically adsorbed coating for protein separation by capillary electrophoresis

To stabilize electroosmotic flow (EOF) and suppress protein adsorption onto the silica capillary inner wall, a cationic hydroxyethylcellulose-graft-poly (poly(ethylene glycol) methyl ether methacrylate) (cat-HEC-g-PPEGMA) graft copolymer composed of cationic backbone and bottle brush-like side chains was synthesized for the first time and used as a novel physically adsorbed coating for protein separation by capillary electrophoresis. Reversed (anodal) and very stable EOF was obtained in cat-HEC-g-PPEGMA-coated capillary at pH 2.2-7.8. The effects of degree of cationization, PEGMA grafting ratio, PEGMA molecular mass, and buffer pH on the separation of basic proteins were investigated. A systematic comparative study of protein separation in bare and HEC-coated capillaries and in cat-HEC-g-PPEGMA-coated capillary was also performed. The basic proteins can be well separated in cat-HEC-g-PPEGMA-coated capillary over the pH range of 2.8-6.8 with good repeatability and high separation efficiency, because the coating combines good protein-resistant property of bottle brush-like PPEGMA side chains with excellent coating ability of cat-HEC backbone. Besides its success in separation of basic proteins, the cat-HEC-g-PPEGMA coating was also superior in the fast separation of other protein samples, such as protein mixture, egg white, and saliva, which indicates that it is a promising coating for further proteomics analysis.     

Synthesis and crystal structure of [ReO(ahp)2(PPh3)]Cl (Hahp=2-amino-3-hydroxypyridine): a novel cationic monooxorhenium(v) complex

The cationic complex [ReO(ahp)₂(PPh₃)]⁺ was isolated as the chloride salt from the reaction of trans-[ReOCl₃(PPh₃)₂] and 2-amino-3-hydroxypyridine (Hahp) in ethanol. Coordination of the chelates only occurs through the amino nitrogen and the phenolate oxygen of ahp^?. The X-ray crystal structure shows a distorted octahedral geometry, in which a phenolate oxygen coordinated trans to the oxo group and the rhenium atom is displaced by 0.2520(1) Å out of the mean equatorial plane towards the oxo oxygen.     

Spectrophotometric determination of cationic surfactants by formation of ternary complexes with Fe(III) and chrome azurol

An extraction-free spectrophotometric method for the determination of cationic surfactants, such as cetylpyridinium chloride, cetyltrimethylammonium bromide and zephiramine is proposed, which is based on the formation of ternary complexes with Fe(III) and chrome azurol S. The molar ratio of the complex is 2:1:1 (Fe(III):chrome azurol S: cationic surfactant). The method is simple, rapid and sensitive, giving an apparent molar absorptivity of 4.5×10⁴ L·mol^?1-cm^?1 and a linear range of 0.1–6.0 μmol/L cationic surfactants. The total cationic surfactant content can be determined directly in aqueous solutions by measuring the absorbance at 680 nm (pH 5.8). The method has been successfully applied to water samples.     

Characterization of chloroprene and maleic anhydride copolymer by 13C-NMR spectroscopy and pyrolysis GC/MS

The radical copolymerizations of chloroprene (CP) and maleic anhydride (MAH) were carried out with AIBN in 1,4-dioxane at 60°C. The monomer reactivity ratios were estimated as r₁ (CP) = 0.38 and r₂ (MAH) = 0.07. Microstructures in the copolymer of chloroprene (CP) and maleic anhydride (MAH) were investigated by 75.4 MHz ¹³C-and 300 MHz ¹H-NMR spectroscopies. Resonances were assigned to the monomer sequence dyads CC, CM, and MC (C = chloroprene, M = maleic anhydride). Well resolved fine structure in the ¹³C-NMR spectra showed that 1,2- and 3,4-structural chloroprene units were negligible in the copolymer. The pyrolysis characterization of the copolymer was also investigated by the pyrolysis gas chromatography mass spectrometry (GC/MS). The fragments of CP and MAH monomers and CP-MAH hybrid dimer, CO, and CO₂ were identified after pyrolysis of the copolymer. © 1994 John Wiley & Sons, Inc.     

Characterization of poly(vinyl alcohol) during the emulsion polymerization of vinyl acetate using poly(vinyl alcohol) as emulsifier

During the emulsion polymerization of vinyl acetate (VAc) using poly(vinyl alcohol) (PVA) as stabilizer and potassium persulfate as initiator, the VAc reacts with PVA forming PVA-graft-PVAc. When the grafted polymer reaches a critical size it becomes water-insoluble and precipitates from the aqueous phase contributing to the formation of polymer particles. Since particle formation and therefore the properties of the final latex will depend on the degree of grafting, it is important to quantify and to characterize the grafted PVA. In this work, the quantitative separation and characterization of the grafted water-insoluble PVA was carried out by a two-step selective solubilization of the PVAc latex, first with acetonitrile to separate PVAc homopolymer, followed by water to separate the water-soluble PVA from the remaining acetonitrile-insoluble material. After the separation, the water-soluble and water-insoluble PVA were characterized by Fourier Transform Infrared (FTIR) spectroscopy and ¹H and ¹³C nuclear magnetic resonance (NMR) analyses, from which the details of the PVA-graft-PVAc structure were obtained. © 1996 John Wiley & Sons, Inc.     

Compatibilisation effect of PP-g-MA copolymer on iPP/SiO2 nanocomposites prepared by melt mixing

In the present study, a series of iPP/SiO₂ nanocomposites, containing 1, 2.5, 5, 7.5, 10 and 15 wt% SiO₂ nanoparticles, were prepared by melt mixing in a twin screw co-rotating extruder. Poly(propylene-g-maleic anhydride) copolymer (PP-g-MA) containing 0.6 wt% maleic anhydride content was added to all nanocomposites at three different concentrations, 1, 2.5 and 5 wt%, based on silica content. Mechanical properties such as tensile strength at break and Young’s modulus were found to increase and to be mainly affected by the content of silica nanoparticles as well as by the copolymer content. For the tensile strength at break as well as for yield point, a maximum was observed, corresponding to the samples containing 2.5-5 wt% SiO₂. At higher concentrations, large nanosilica agglomerates are formed that have as a result a decrease in tensile strength. Young’s modulus increases almost linearly on the addition of SiO₂, and takes values up to 60% higher than that of neat iPP. Higher concentrations of PP-g-MA resulted in a further enhancement of mechanical properties due to silica agglomerate reduction. This finding was verified from SEM and TEM micrographs. Evidently the surface silica hydroxyl groups of SiO₂ nanoparticles react with maleic anhydride groups of PP-g-MA and lead to a finer dispersion of individual SiO₂ nanoparticles in the iPP matrix. The enhanced adhesion in the interface of the two materials, as a result of the mentioned reaction, has been studied and proved by using several equations. The increased Vicat point of all nanocomposites, by increasing the PP-g-MA content, can also be mentioned as a positive effect.     

Synthesis of poly(n‐butyl acrylate) homopolymer and poly(styrene‐b‐n‐butyl acrylate‐b‐styrene) triblock copolymer via AGET emulsion ATRP using a cationic surfactant

Cationic emulsions of triblock copolymer particles comprising a poly(n‐butyl acrylate) (PⁿBA) central block and polystyrene (PS) outer blocks were synthesized by activator generated by electron transfer (AGET) atom transfer radical polymerization (ATRP). Difunctional ATRP initiator, ethylene bis(2‐bromoisobutyrate) (EBBiB), was used as initiator to synthesize the ABA type poly(styrene‐b‐n‐butyl acrylate‐b‐styrene) (PS‐PⁿBA‐PS) triblock copolymer. The effects of ligand and cationic surfactant on polymerizations were also discussed. Gel permeation chromatography (GPC) was used to characterize the molecular weight (M_n) and molecular weight distribution (MWD) of the resultant triblock copolymers. Particle size and particle size distribution of resulted latexes were characterized by dynamic light scattering (DLS). The resultant latexes showed good colloidal stability with average particle size around 100–300 nm in diameter. Glass transition temperature (T_g) of copolymers was studied by differential scanning calorimetry (DSC). © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 611–620     

Characterization of PBT/POSS nanocomposites prepared by in situ polymerization of cyclic poly(butylene terephthalate) initiated by functionalized POSS

Novel poly(butylene terephthalate) (PBT)/polyhedral oligomeric silsesquioxane (POSS) nanocomposites were synthesized by ring‐opening polymerization of cyclic poly(butylene terephthalate) initiated by functionalized POSS with various feed ratios. The impact of POSS incorporation on melting and crystallization behaviors of PBT/POSS nanocomposites was investigated by means of X‐ray diffraction and differential scanning calorimetry. It was found that the novel organic–inorganic association result in the significant alterations in the melting and crystallization behavior of PBT. Thermal studies confirmed that the incorporation of POSS can enhance the thermal stability of the polymers, and the copolymer glass transition temperature increased with the increasing of POSS macromonomer content. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1853–1859, 2010     

Stimuli‐responsive cationic terpolymers by RAFT polymerization: Synthesis,characterization, and protein interaction studies

The controlled synthesis and characterization of a range of stimuli responsive cationic terpolymers containing varying amounts of N‐isopropylacrylamide (NIPAM), 3‐(methylacryloylamino)propyl trimethylammonium chloride (MAPTAC), and poly(ethylene glycol)monomethyl methacrylate (PEGMA) is presented. The terpolymers were synthesized using reversible addition‐fragmentation chain transfer (RAFT) polymerization. Compositions of the terpolymers determined using ¹H NMR were in close agreement to the theoretical values determined from the monomer feed ratios. GPC‐MALLS was used to analyze the molecular weight characteristics of the polymers, which were found to have low polydispersities (M_w/M_n 1.1–1.4). The phase transitions were studied as a function of PEGMA and NIPAM content using temperature controlled ¹H NMR and turbidity measurements (UV‐Vis). The relationship between thermal stability and the comonomer ratio of the polymers was measured using thermogravimetric analysis (TGA). Protein interaction studies were performed to determine the suitability of the polymers for biological applications. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4021–4029, 2008     

Graft copolymers having hydrophobic backbone and hydrophilic branches. XXIII. Particle size control of poly(ethylene glycol)-coated polystyrene nanoparticles prepared by macromonomer method

Monodisperse polymeric nanospheres, which consist of polystyrene cores and poly(ethylene glycol) (PEG) branches on their surfaces, were prepared by the dispersion copolymerization of styrene (St) with PEG macromonomers that had a methacryloyl (MMA-PEG) or p-vinylbenzyl (St-PEG) end group in various organic solvent/water media. Electron spectroscopy for chemical analysis (ESCA) of the nanosphere surfaces indicated that PEG macromonomer chains were favorably located on their surfaces. The morphologies of the nanospheres were observed via a scanning electron micrograph (SEM), and particle sizes were estimated by a submicron particle analyzer. When both the concentration of macromonomers and molecular weight were higher, small nanospheres in diameter were obtained. Larger nanospheres in diameter were obtained using macromonomers with low molecular weight at lower concentration. The functions that correlate the diameter (D_n) on different concentration units were D_n = K[St]^0.64[MMA-PEG]^{−0.53±0.01}[I]^−0.49 and D_n = K[St]^0.80[St-PEG]^{−0.69±0.01}[I]^−0.22, where [I], [St], [MMA-PEG], and [St-PEG] are initiator, styrene, MMA-PEG, and St-PEG macromonomer concentration in feed, respectively. When the reaction parameters such as the molecular weight of the macromonomers were properly chosen, the particle size could be controlled in a range from ca. 80 to 3100 nm. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2155–2166, 1999