Ti-Zr催化剂对NaH/Al复合物可逆储氢特性的影响

采用机械球磨(NaH/Al+Ti)和(NaH/Al+Ti-Zr)复合物的方法加氢制备了NaAlH4配位氢化物, 系统研究了Ti、Ti-Zr催化剂以及不同加氢条件对其可逆储氢行为的影响. 结果表明, 对于NaH/Al体系的吸放氢性能, 共掺金属Ti粉/Zr粉的催化作用比单独掺金属Ti粉的催化作用要好. 随着加氢温度从85 ℃上升到140 ℃, 体系的吸氢容量先增后减, 并在120 ℃时达到最大值; 同时, 发现共掺Ti-Zr催化剂的复合物具有最佳的储氢性能, 在120和85 ℃时的吸氢量分别为4.61%和3.52%(w), 比仅掺Ti 催化剂的复合物分别高出0.40%和0.70%(w)的吸氢量. 随着加氢压力的增大, (NaH/Al+Ti-Zr)复合物的吸氢性能随之提高. XRD和DSC分析结果表明, NaAlH4体系的放氢过程明显发生两步分解反应, 共掺Ti-Zr催化剂的复合物储氢性能优于单独掺Ti 催化剂的原因是, 共掺催化剂能有效改善NaAlH4体系吸放氢反应的动力学性能,并降低体系的放氢温度.     

络合氢化物Ti-NaAlH4的制备与储氢特性

采用Ti粉为催化剂前驱体、预处理Al粉和NaH为合成原料, 通过机械球磨-加氢方法合成出络合氢化物Ti-NaAlH4, 系统研究了球磨保护气氛、球磨时间和氢化加氢压力等制备参数对其储氢性能的影响. 结果表明, 制备方法对Ti-NaAlH4储氢特性有很大影响. 与氩气保护气氛相比, 在氢气气氛中球磨制备的复合物具有更高的吸放氢性能. 在氢气保护气氛下, 随着球磨时间从6 h增至24 h, 复合物的吸氢容量和吸氢速率先增后减, 12 h时达到最佳值, 而复合物的放氢容量和放氢速率则逐渐增高; 进一步延长球磨时间会使颗粒发生团聚, 从而导致吸氢性能下降. 随着氢化加氢压力从7.5 MPa升至13.5 MPa, 复合物的吸氢容量(质量分数)由2.83%逐渐增至4.21%. 复合物球磨后出现的Na3AlH6中间氢化物相表明, 在氢气下掺Ti球磨对NaH和Al的氢化反应起到很好的促进作用.     

镨、钕氢化物催化剂对NaH/Al复合物吸放氢性能的影响

采用NaH和Al为合成原料,镨、钕氢化物为催化剂,通过机械球磨(NaH/Al+6%(摩尔分数)RE-H)(RE=Pr,Nd)复合物的方法并加氢合成NaAlH4络合氢化物,系统研究了催化剂对其吸放氢性能的影响。结果表明,加入PrH2.92和NdH2.27能明显改善NaH/Al复合物的吸放氢动力学性能,有效降低NaAlH4的脱氢温度。(NaH/Al+6%PrH2.92)和(NaH/Al+6%NdH2.27)复合物的120℃吸氢容量分别为3.57%和3.61%(质量分数),170℃放氢容量分别为2.57%和2.95%;且两者均具有较好的吸放氢循环稳定性,但吸(放)氢后样品中均存在少量Na3AlH6相,表明样品的吸(放)氢反应进行得并不彻底,使得其实际吸放氢容量低于理论可逆储氢容量。研究表明,PrH2.92和NdH2.27在球磨、吸/放氢过程中始终稳态存在,起着催化储氢作用;(NaH/Al+6%PrH2.92)复合物的放氢活化能稍低于(NaH/Al+6%NdH2.27)复合物。     

3NaBH4/ErF3复合储氢材料的制备及吸放氢特性

采用高能球磨法制备了3NaBH4/ErF3复合储氢材料, 并研究了其相结构和储氢性能. X射线衍射(XRD)显示, NaBH4和ErF3在球磨过程中未发生反应; 同步热分析(TG-DSC)测试结果表明, 3NaBH4/ErF3体系在420℃开始放氢, 比相同测试条件下纯NaBH4的放氢温度降低了约100℃, 放氢量为3.06%(质量分数). 压力-成分-温度(Pressure-Composition-Temperature, PCT)性能测试结果显示, 3NaBH4/ErF3复合储氢材料在较低的温度(355~413℃)及平台氢压(<1 MPa)下即拥有良好的可逆吸放氢性能, 最高可逆吸氢量可达到2.78%(质量分数), 吸氢后体系重新生成了NaBH4相. 计算得吸氢焓变仅为-36.8 kJ/mol H2; 而放氢焓变为-180.8 kJ/mol H2. NaBH4在ErF3的作用下提高了热动力学性能, 并实现了可逆吸放氢.     

掺Ti球磨NaH/Al复合物的微结构和储氢特性

本文采用机械球磨法制备了(NaH/Al)+x(摩尔分数, %)Ti(x=0, 4, 6, 10)复合物, 研究了不同球磨气氛和Ti催化剂含量对其微结构和储氢性能的影响, 使球磨(NaH/Al)体系储氢的容量达到质量分数为4.01%.     

MgH_2+20%(w)MgTiO_3复合材料的吸/放氢性能(英文)

为了降低MgH2的吸放氢温度,提高其吸放氢动力学性能,本文通过球磨方法制备了MgH2+20%(w)MgTiO3复合储氢材料,并研究了其储氢性能.X射线衍射(XRD)结果表明,MgTiO3在与MgH2球磨过程中生成Mg2TiO4和TiO2,并且Mg2TiO4和TiO2在体系的吸放氢过程中保持稳定,能够对MgH2的吸放氢过程产生催化作用.程序升温脱附和吸/放氢动力学测试结果表明,添加MgTiO3后MgH2的初始放氢温度从389°C降至249°C.150°C下的吸氢量从0.977%(w)提高到2.902%(w),350°C下的放氢量从2.319%(w)提高到3.653%(w).同时,MgH2放氢反应的活化能从116kJ·mol-1降至95.7kJ·mol-1.与MgH2相比,MgH2+20%(w)MgTiO3复合材料的热力学与动力学性能均有显著提高,这主要是由于球磨和放氢过程中原位生成的TiO2和Mg2TiO4具有良好的催化活性.     

添加C10H10Cl2Ti对6LiBH4-CaH2-3MgH2体系储氢性能的影响

C_(10)H_(10)Cl_2Ti的添加可以有效改善6LiBH_4-CaH_2-3MgH_2样品吸放氢性能,添加的质量分数为5%时具有较好的催化效果。样品的起始和终止放氢温度比原始样品分别降低约30和25℃,可逆储氢量(质量分数)约为8.1%。添加C_(10)H_(10)Cl_2Ti催化剂的样品在360℃下等温放氢速率比原始样品提高了178%。两步放氢反应的表观活化能分别为131.4和138.8 kJ·mol~(-1),相比原始样品降低了约18.6%和15.8%。利用X射线光电子能谱(X-ray photoelectron spectroscopy,XPS)对样品进行分析发现,热分解过程中C_(10)H_(10)Cl_2Ti生成了多价态的Ti化合物,催化了LiBH_4与CaH_2的反应,从而改善了复合体系的储氢性能。     

KH添加对Na-Al-H配位氢化物可逆放氢性能的影响

以NaH粉和Al 粉为合成原料, 分别采用2% (摩尔分数, x) CeCl₃和2% CeCl₃/y% KH (y=0.02, 0.04)为催化添加剂, 在室温和3 MPa氢压下, 通过反应球磨(NaH/Al+CeCl₃)和(NaH/Al+CeCl₃/yKH) (y=0.02, 0.04)复合物成功制备出Na-Al-H 配位氢化物. 吸放氢性能测试结果表明, KH的加入能有效改善Na-Al-H 体系中第二步脱氢反应放氢动力学性能. (NaH/Al+CeCl₃/0.02KH)复合物170℃放氢时可在20 min内完成脱氢过程, 且在较低温度(100-140℃)下具有良好的可逆吸放氢性能. Kissenger 方法计算表明, 添加KH可降低Na-Al-H 体系第二步脱氢反应的表观活化能, 降低其放氢峰值温度. 相结构分析表明, KH的添加使Na-Al-H 体系中Na₃AlH₆的晶胞体积发生膨胀, 进而提高体系的第二步放氢动力学性能.     

氢化燃烧法合成La2-xNixMg17(x=0.5,1,1.5)材料的储氢性能

采用氢化燃烧法制备La2-xNixMg17(x=0.5, 1, 1.5)三元体系储氢材料, 对其热力学、动力学进行研究发现: 该体系材料具有很好的活性和较高的储氢量, 其中La1.5Ni0.5Mg17在573 K时吸放氢量分别为5.40和5.15 mass% H. 在553 K下, 体系α-β相区在600 s之内吸放氢反应分数均大于91%, 随着含Ni量的增加材料储氢容量降低, 吸放氢速率增大.物相分析知道体系吸氢后的主相是MgH2, 放氢后主相为Mg, 同时存在Mg2Ni, LaNi5或LaH3等催化物质, 从而使材料的氢化动力学性能得以明显改善.     

稀土储氢合金在有机氢化物中的吸氢行为和吸氢热力学性能

研究了富镧混合稀土－镍储氢合金（MlNi5)与有机化合物（C6H6）组成的浆液体系的吸氢行为和吸氢热力学性能。测定了不同温度（10，20，30，40℃）下两个不同系统的吸氢压力－成分等温（PCT）曲线，并分别计算出气固系统和气固液系统吸氢反应的热力学函数值ΔH,ΔS。     

利用手持技术改进测定乙醇分子结构实验

利用压强传感器代替排水集气法,改进测定乙醇分子结构实验的仪器装置,并探索最佳反应条件。另外,设计两个空白实验,结合压强变化曲线对实验误差进行相关讨论。     

光谱仪测试范围的扩展

由于石化行业的生产需要，其材质的使用具有多样性和广泛性，经常会出现顾客委托的测试样品的一个或几个元素跨越光谱仪现有测试程序测量范围的情况。本法通过对光谱仪测试原理的认识，根据光谱仪的测试能力及标样的采集，实现了一个或几个元素测量范围的扩展，并对其测量的影响因素进行了研究。     

Influence of viscosity of medium on processes of oxygen quenching of excited states of mesoporphyrin

The oxygen quenching rate constants for singlet and triplet excited states of the dimethyl ester of mesoporphyrin IX increase with decreasing viscosity of the medium and reach a maximum at a viscosity of approximately 0.4 mPa·sec, after which the rate constants begin to decrease. The drop in rate constant with increasing fluidity of the medium may be related to a nonequilibrium character of the elementary act in the interaction of the reactants in the solvent cage. In viscous media such as isopropyl alcohol, isobutyl alcohol, and isoamyl alcohol, the reaction radius is greater than the sum of the radii of the reacting particles. The long-range character of these processes is due to the relatively weak dependence of the quenching probability on distance.Translated from Teoreticheskaya i Éksperimental'naya Khimiya, Vol. 25, No. 2, pp. 161–167, March–April, 1989.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

物质分配系数的测定实验改进

实验教学目的是从解决实际问题出发,以实验技术训练和实验设计思想培养为目标。介绍了将单一的物质分配系数测定实验改进为综合实验,提高了实验效果及实验资源利用率。     

Neutral diterpenoids of oleoresins of five species of conifers of Transcarpathia

The compositions of the neutral diterpenoids of the oleoresins of five species of conifers growing in the Transcarpathia have been studied. It has been found that the oleoresins ofAbies alba M.,Larix decidua M., andPicea excelsa L. contain more than 50% of neutral diterpenoids. The group and qualitative compositions of the oxygen-containing diterpenoids have been determined. In the oleoresins ofAbies alba,Picea excelsa, andPicea abies tertiary alcohols — cis-abienol and isocembrol — predominate, while inLarix decidua the main component is the hydroxy ester larixyl acetate. Primary alcohols related to the resin acids have been found in all the oleoresins investigated. Features of the distribution of diterpenoids according to the species of conifers have been revealed. The results obtained are necessary for the chemotaxonomy of conifers of the family Pinceae.Novosibirsk Institute of Organic Chemistry, Siberian Branch, Academy of Sciences of the USSR. Translated from Khimiya Prirodynkh Soedinenii, No. 6, pp. 812–816, November–December, 1988.     

Calculation of enthalpies of hydrogenation of hydrocarbons

Sets of hydrogen molecule equivalents have been developed which permit the calculation of hydrogenation of different types of carbon-carbon bonds from ab initio total energies (3-21G and 6-31G* basis sets, and, to a more limited extent, for MP2/6-31G* data) of reactants and products. The calculated enthalpies of hydrogenation are in good agreement with experiment for unstrained molecules, with average errors on the order of 2 kcal/mol. The 6-31G* equivalents allow the enthalpies for strained molecules to be calculated accurately, but the 3-21G equivalents do not. The equivalents for both basis sets have been tested by calculating the enthalpies of hydrogenation of carbon-carbon bonds in nitrogen- and oxygen-containing organic molecules, free radicals, and classical carbocations. The results are in good agreement with experiment in most cases.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。