Capillary electrochromatography with monolithic silica columns. IV. Electrochromatographic characterization of polar bonded monolithic stationary phases having surface-bound cyano functionalities

Two polar ligands, namely 3-hydroxypropionitrile and 1H-imidazole-4,5-dicarbonitrile (IDCN) were covalently attached to epoxy-activated silica-based monolithic capillary columns via an epoxide ring-opening reaction to yield CN-OH-Monolith and 2CN-OH-Monolith, respectively. The silica monolith was prepared by a sol-gel process, and the resulting "rod-like" stationary phase was subjected to pore tailoring with an alkaline solution to convert small pore domains to mesopore domains, thus yielding a monolith with bimodal pore structure consisting of flow through pores (i.e., flow channels for mobile-phase flow) and mesopores that provide most of the adsorption capacity of the monolith toward the separated solutes. The two polar monoliths, CN-OH-Monolith and 2CN-OH-Monolith, were evaluated in normal-phase CEC with organic-rich mobile phases less polar than the stationary phase. The 2CN-OH-Monolith bearing more polar functions than the CN-OH-Monolith exhibited more retention and improved selectivity toward model polar solutes.     

Separation of acidic and basic compounds in capillary electrochromatography with polymethacrylate-based monolithic columns

Methacrylate-based monolithic columns with electroosmotic flow (EOF) or very weak EOF are prepared by in situ copolymerization in the presence of a porogen in fused-silica capillaries pretreated with a bifunctional reagent. Satisfactory separations of acidic and basic compounds on the column with EOF at either low or high pH are achieved, respectively. With sulfonic groups as dissociation functionalities, sufficient EOF mobility still remains as high as 1.74 x 10(-4) cm2 s(-1) V(-1) at low pH. Under this condition, seven acidic compounds are readily separated within 5.7 min. Moreover, at high pH, the peak shape of basic compounds is satisfactory without addition of any masking amines into running mobile phase since the secondary interaction between the basic compounds and the monolithic stationary phase are minimized at high pH. Reversed-phase mechanism for both acidic and basic compounds is observed under investigated separation conditions. In addition, possibilities of acidic and basic compound separations on a monolithic column with extremely low EOF are discussed.     

HILIC mode separation of polar compounds by monolithic silica capillary columns coated with polyacrylamide

HILIC mode columns were prepared by an on-column polymerization of acrylamide on a monolithic silica capillary column modified with N-(3-trimethoxysilylpropyl)methacrylamide as the anchor group. The products showed HILIC mode retention characteristics with three times greater permeability and slightly higher column efficiency compared to a commercially available amide-type HILIC column packed with 5-μm particles. The selectivity of the monolithic silica-based column was similar to that of the particulate column for each group of solutes towards nucleosides, nucleic bases and carbohydrate derivatives, although a considerable difference was observed in the selectivity for the solute groups. Although the retention of solutes based on the polar functionality was much smaller with the monolithic silica columns, which had a smaller phase ratio, than with the particle-packed column, the former can achieve better separation utilizing the high permeability and higher column efficiencies of a longer column.     

Capillary electrochromatography with monolithic stationary phases. 4. Preparation of neutral stearyl-acrylate monoliths and their evaluation in capillary electrochromatography of neutral and charged small species as well as peptides and proteins

A neutral, nonpolar monolithic capillary column having a relatively strong electroosmotic flow (EOF) yet free of electrostatic interactions with charged solutes was developed for the reversed-phase capillary electrochromatography (RP-CEC) of neutral and charged species including peptides and proteins. The neutral nonpolar monolith is based on the in situ polymerization of pentaerythritol diacrylate monostearate (PEDAS) in a ternary porogenic solvent composed of cyclohexanol, ethylene glycol, and water. PEDAS plays the role of both the cross-linker and the ligand provider, generating a macroporous nonpolar monolith having C17 chains as the chromatographic ligands. Despite the fact that the neutral PEDAS monolith is devoid of fixed charges, the monolithic capillary columns exhibited a relatively strong EOF due to the ability of PEDAS to adsorb sufficient amounts of electrolyte ions from the mobile phase. The adsorbed ions imparted the neutral PEDAS monolith the zeta potential necessary to support the EOF required for mass transport across the monolithic column. The absence of fixed charges on the surface of the neutral PEDAS monolith and in turn the adsorption sites for electrostatic attraction of charged solutes allowed the rapid and efficient separations of proteins and peptides at pH 7.0, with an average plate number of 255,000 and 121,000 plates/m, respectively. To the best of our knowledge, this constitutes the first report on the separation of proteins at neutral pH by RP-CEC using a neutral monolithic column.     

Preparation and evaluation of amphiphilic silica‐based monolithic column having surface‐bound octanoyl‐aminopropyl moieties for capillary electrochromatography

A novel amphiphilic silica‐based monolithic column having surface‐bound octanoyl‐aminopropyl moieties was successfully prepared by a one‐step in situ derivatization process. As expected, the amphiphilic monolithic column exhibited RP chromatographic behavior toward non‐polar solutes (e.g., alkyl benzenes) with high column performance. As the pH of the buffer inside the column increases, the EOF changed from −2.65×10⁻⁸m² V⁻¹s⁻¹ at pH 3.0 to 1.20×10⁻⁸ m² V⁻¹s⁻¹ at pH 8.0 with the reversion of EOF at about pH 6.4. Using acidic mobile phase, five aromatic acids can be efficiently separated in less than 6 min under co‐EOF conditions. For basic compounds, symmetrical peaks were obtained due to the existence of hydrophilic acyl amide group, which can effectively minimize the adsorption of the positively charged basic analyte to the silica‐based surface of the capillary column.     

Controlling the surface chemistry and chromatographic properties of methacrylate-ester-based monolithic capillary columns via photografting

Preparation of monolithic capillary columns for separations in the CEC mode using UV-initiated polymerization of the plain monolith followed by functionalization of its pore surface by photografting has been studied. The first step enabled the preparation of generic poly(butyl methacrylate-co-ethylene dimethacrylate) monoliths with optimized porous properties, controlled by the percentages of porogens 1-decanol and cyclohexanol in the polymerization mixture, irradiation time, and UV light intensity. Ionizable monomers [2-(methacryloyloxy)ethyl]trimethylammonium chloride or 2-acryloamido-2-methyl-1-propanesulfonic acid were then photografted onto the monolithic matrix, allowing us to control the direction of the EOF in CEC. Different strategies were applied to control the grafting density and, thereby, the magnitude of the EOF. To control the hydrophobic properties, two approaches were tested: (i) cografting of a mixture of the ionizable and hydrophobic monomers and (ii) sequential grafting of the ionizable and hydrophobic monomers. Cografting resulted in similar retention but higher EOF. With sequential grafting, more than 50% increase in retention factors was obtained and a slight decrease in EOF was observed due to shielding of the ionizable moieties.     

Capillary electrochromatography with contactless conductivity detection for the determination of some inorganic and organic cations using monolithic octadecylsilica columns

A fast separation of alkali and alkaline earth metal cations and ammonium was carried out by capillary electrochromatography on monolithic octadecylsilica columns of 15 cm length and 100 μm inner diameter using water/methanol mixtures containing acetic acid as mobile phase. On-column contactless conductivity detection was used for quantification of these non-UV-absorbing species. The method was also extended successfully to the determination of small amines as well as of amino acids, and the separation selectivity was optimized by varying the composition of the mobile phase. Detection limits of about 1 μM were possible for the inorganic cations as well as for the small amines, while the amino acids could be quantified down to about 10 μM. The separation of 12 amino acids was achieved in the relatively short time of 10 min.     

Recognition of oxytocin by capillary electrochromatography with monolithic tetrapeptide-imprinted polymer used as the stationary phase

Using YPLG (Tyr-Pro-Leu-Gly), a tetrapeptide, as the template, an imprinted monolithic column was prepared and applied to the selective recognition of oxytocin based on the epitope approach and capillary electrochromatography (CEC). By optimizing the polymerization solution in terms of functional monomer, cross-linking reagent, porogen, and imprinted template via CEC evaluations of synthesized columns, an imprinted monolith with good recognition capacity (the imprinting factors for YPLG and oxytocin were 4.499 and 4.013, respectively) and high column efficiency (theoretical plates for YPLG and oxytocin were 22,995 plates/m and 16,952 plates/m, respectively) was achieved. In addition, the effects of various experimental parameters on the recognition of oxytocin, including the organic modifier content, the buffer concentration, and the pH value, were studied systematically. Furthermore, a mixture of oxytocin and other proteins was analyzed using this monolithic CEC column, and oxytocin was eluted much more slowly than other large biomolecules, which demonstrated the high selective recognition ability of such an imprinted monolith for oxytocin with PLG (Pro-Leu-Gly) as the epitope. Figure Separation of a mixture of oxytocin, BSA, bovine hemoglobin, ovalbumin, and lysozyme on the open column, the blank monolithic column, and the monolithic YPLG-imprinted column     

Stepwise gradient of buffer concentration for capillary electrochromatography of peptides on sulfonated naphthalimido-modified silyl silica gel

The advantage of using a stepwise gradient of buffer concentration in CEC was demonstrated with the mixed-mode stationary phase, 3-(4-sulfo-1,8-naphthalimido)propyl-modified silyl silica gel (SNAIP). Before the application of a stepwise gradient, the effect of buffer concentration on the separations of six peptides and tryptic digests was investigated. Bubble formation caused by Joule heating at currents up to 95 microA was successfully suppressed by using SNAIP column even without pressurization, which contributed to a stepwise gradient of buffer concentration. Utilizing the stepwise gradient improved and shortened the separation of six peptides as compared to the separation under an isocratic elution.     

Capillary electrochromatography with monolithic silica columns III. Preparation of hydrophilic silica monoliths having surface-bound cyano groups: chromatographic characterization and application to the separation of carbohydrates, nucleosides, nucleic acid bases and other neutral polar species

Two synthetic routes have been introduced and evaluated for the preparation of hydrophilic silica-based monoliths possessing surface-bound cyano functions. In one synthetic scheme, the silica monolith was reacted in a single step with 3-cyanopropyldimethylchlorosilane to yield a cyano phase referred to as CN-monolith. In a second synthetic route, the silica monolith was first reacted with gamma-glycidoxypropyltrimethoxysilane (gamma-GPTS), followed by a reaction with 3-hydroxypropionitrile (3-HPN) to give a stationary phase denoted CN-OH-monolith. Although the gamma-GPTS was intended to play the role of a spacer arm to link the 3-HPN to the silica surface, this spacer arm became an integral part of the hydrophilic stationary phase. Thus, the CN-OH-monolith can be viewed as a double-layered stationary phase (i.e., stratified phase) with a hydroxy sub-layer and a cyano top layer. Due to its stronger hydrophilic character, the CN-OH-monolith yielded higher retention and better selectivity than the CN-monolith. The CN-OH-monolith was demonstrated in the normal-phase capillary electrochromatography (CEC) of various polar compounds including phenols and chloro-substituted phenols, nucleic acid bases, nucleosides, and nitrophenyl derivatives of mono- and oligosaccharides. The CN-OH-monolith yielded a relatively strong electroosmotic flow over a wide range of mobile phase composition, thus allowing rapid separation of the polar compounds studied.     

硅胶电色谱分离机理的研究

对硅胶电色谱柱的性能进行了考察,发现在水／有机溶剂流动相条件下,几乎不存在气泡问题,流动相的组成在有机溶剂浓度、电解质浓度、ＰＨ值等方面可以在较大范围变化,选用５种典型样品,对硅胶电色谱的分离机理进行了系统研究,发现有反相分离机理、正相吸附机理、离子交换机理以及电泳机理参与作用。同时考察了有机溶剂浓度、电解质浓度、ＰＨ等对分离的影响。此外,还首次提出了一种全新的电色谱模式－动态改性硅胶电色谱。     

Comparison on photo-initiators for the preparation of methacrylate monolithic columns for capillary electrochromatography

The synthesis of lauryl methacrylate monoliths for capillary electrochromatography by UV polymerization using several free-radical initiators (α,α′-azobisisobutyronitrile, 2,2-dimethoxy-2-phenylacetophenone, dibenzoyl peroxide (BPO) and lauroyl peroxide (LPO)) has been investigated. Using a 1,4-butanediol/1-propanol mixture as porogenic solvent, the influence of each initiator and its content on the morphological and electrochromatographical properties of beds was evaluated. Under their respective optimum content, satisfactory separations of a test mixture of PAHs with similar efficiencies (minimum plate heights of 8.0–12.7 μm obtained from Van Deemter plots) were achieved for the four investigated photo-initiators. The columns photo-polymerized with LPO provided the best compromise between chromatographic performance and analysis time. Moreover, this initiator showed a fine control in the column retention properties. The resulting monolithic columns exhibited a good run-to-run repeatability in the tested chromatographic parameters (RSD < 2.4%) for all initiators investigated; and satisfactory column-to-column repeatability (RSD < 6.0%), except for beds photo-polymerized with BPO (RSD < 10.8%).     

Postpolymerization modification of a hydroxy monolith precursor. Part I. Epoxy alkane and octadecyl isocyanate modified poly (hydroxyethyl methacrylate‐co‐pentaerythritol triacrylate) monolithic capillary columns for reversed‐phase capillary electrochromatography

A novel precursor monolithic capillary column referred to as “hydroxy monolith” or OHM was prepared by the in situ copolymerization of hydroxyethylmethacrylate (HEMA) with pentaerythritol triacrylate (PETA) yielding the neutral poly(HEMA‐co‐PETA) monolith. The neutral precursor OHM capillary thus obtained was subjected to postpolymerization modifications of the hydroxyl functional groups present on its surface with 1,2‐epoxyalkanes catalyzed by boron trifluoride (BF₃) ultimately providing Epoxy OHM C‐m capillary column at varying alkyl chain lengths where m = 8, 12, 14, and 16 for RP‐CEC. Also, the same precursor OHM was grafted with octadecyl isocyanate yielding Isocyanato OHM C‐18 column to provide an insight into the effect of the nature of the linkage to the surface hydroxyl groups of the OHM precursor. While the epoxide reaction leaves on the surface of the OHM precursor hydroxy‐ether linkages, the isocyanato reaction leaves carbamate linkages on the same surface of the OHM precursor. This study revealed that changing the alkyl chain length resulted in changing the column phase ratio (?) and also the solute distribution constant (K). While increasing the surface alkyl chain length increased steeply the solute hydrophobic selectivity, i.e. methylene group selectivity, the nature of the ligand linkage produced different retention for the same solutes and affected the selectivity of slightly polar solutes. The various monoliths proved very useful for RP‐CEC of different small solutes at varying polarity over a wide range of mobile phase composition.     

Selectivity comparisons of monolithic silica capillary columns modified with poly(octadecyl methacrylate) and octadecyl moieties for halogenated compounds in reversed-phase liquid chromatography

Stationary phase selectivities for halogenated compounds in reversed-phase HPLC were compared using C18 monolithic silica capillary columns modified with poly(octadecyl methacrylate) (ODM) and octadecyl moieties (ODS). The preferential retention of halogenated benzenes on ODM was observed in methanol/water and acetonitrile/water mobile phases. In selectivity comparison of selected analytes on ODM and ODS, greater selectivities for halogenated compounds were obtained with respect to alkylbenzenes on an ODM column, while similar selectivities were observed with a homologous series of alkylbenzenes on ODM and ODS columns. These data can be explained by greater dispersive interactions by more densely packed octadecyl groups on the ODM polymer coated column together with the contribution of carbonyl groups in ODM side chains. For the positional isomeric separation of dihalogenated benzenes (ortho-, meta-, para-), the ODM column also provided better separation of these isomers for the adjacently eluted isomers that cannot be completely separated on an ODS column in the same mobile phase. These results imply that the ODM column can be used as a better alternative to the ODS column for the separation of other halogenated compounds.     

Postpolymerization modification of a hydroxy monolith precursor. Part II. Epoxy biphenyl modified poly (hydroxyethyl methacrylate‐co‐pentaerythritol triacrylate) monolithic capillary columns for reversed‐phase capillary electrochromatography based on π–π and hydrophobic interactions

In this second part of the series of investigations involving the postpolymerization modification of a hydroxy monolith (OHM) capillary column, the surface hydroxyl groups were reacted with epoxy biphenyl thus yielding the so‐called Biphenyl OHM capillary column. The modification involved the epoxy ring opening of the 2‐biphenylyl glycidyl ether catalyzed by BF₃ and its subsequent reaction with the hydroxyl groups on the OHM precursor surface. The Biphenyl OHM capillary column thus obtained exhibited the typical reversed phase behavior by primarily hydrophobic interactions vis‐à‐vis the homologous series of alkyl benzenes and in addition by π–π interactions toward nitroalkane homologous series via their π‐electron rich nitro groups. This dual retention mechanism was very distinctly observed with a set of PAH solutes in the sense that the k values of the PAH solutes were comparable to those obtained on a more non polar stationary phase, namely the Epoxy OHM C‐16 reported in the preceding article. Other aromatic solutes showed the dual retention mechanism on the Biphenyl OHM capillary including phenols, anilines derivatives, and phenoxy acid herbicides. The Biphenyl OHM capillary exhibited good reproducibility from run‐to‐run, day‐to‐day, and column‐to‐column.     

An original way to use a β-cyclodextrin-bonded silica stationary phase in electrochromatography. Application to the achiral separation of nucleobases and nucleosides

Summary Although β-cyclodextrin-bonded silica stationary phases are usually dedicated to the separation of enantiomers, they can also be used for achiral purposes, taking advantage of the complex interactions between the solutes and the cyclodextrins. The work described in this paper was intended to show how such stationary phases can be used in short-end injection capillary electrochromatography (CEC) for rapid (<6 min) resolution of a mixture of purines and pyrimidines. Several experimental conditions (mobile-phase composition, voltage and temperature) were investigated to determine the optimum operating conditions for the method, which can also be applied to the analysis of nucleosides. Quantitative analysis was also performed; theophylline was used as internal standard to assess the linearity and the repeatability of the method. Limits of detection ranged from 4 to 13 μm and repeatability was good (RSD never exceeded 2.6%).     

Capillary electrochromatography with monolithic silica column: I. Preparation of silica monoliths having surface-bound octadecyl moieties and their chromatographic characterization and applications to the separation of neutral and charged species

Monolithic silica columns with surface-bound octadecyl (C18) moieties have been prepared by a sol-gel process in 100 microm ID fused-silica capillaries for reversed-phase capillary electrochromatography of neutral and charged species. The reaction conditions for the preparation of the C18-silica monoliths were optimized for maximum surface coverage with octadecyl moieties in order to maximize retention and selectivity toward neutral and charged solutes with a sufficiently strong electroosmotic flow (> 2 mm/s) to yield rapid analysis time. Furthermore, the effect of the pore-tailoring process on the silica monoliths was performed over a wide range of treatment time with 0.010 M ammonium hydroxide solution in order to determine the optimum time and conditions that yield mesopores of narrow pore size distribution that result in high separation efficiency. Under optimum column fabrication conditions and optimum mobile phase composition and flow velocity, the average separation efficiency reached 160 000 plates/m, a value comparable to that obtained on columns packed with 3 microm C18-silica particles with the advantages of high permeability and virtually no bubble formation. The optimized monolithic C18-silica columns were evaluated for their retention properties toward neutral and charged analytes over a wide range of mobile phase compositions. A series of dimensionless retention parameters were evaluated and correlated to solute polarity and electromigration property. A dimensionless mobility modulus was introduced to describe charged solute migration and interaction behavior with the monolithic C18-silica in a counterflow regime during capillary electrochromatography (CEC )separations. The mobility moduli correlated well with the solute hydrophobic character and its charge-to-mass ratio.     

Determination of biogenic quaternary ammonium compounds on fused silica capillary columns with a splitless injector as a chemical reactor/pyrolysis chamber

A conventional splitless injector is used as a pyrolysis chamber or chemical reactor for the N-demethylation of acetylcholine and other choline esters. The novel uses of 2-aminoethanol as a N-demethylation reagent in splitless injection and bonded-phase fused silica capillary columns in the separation of the tertiary amine derivatives of choline esters are described. A comparison is made between non-polar and moderately polar fused silica capillary columns in the separation of choline esters.     

Active centers on the surface of thermoactivated silica. Their reactivity toward organoaluminum compounds

Interaction between organoaluminum compounds (triethylaluminum, ethoxydiethylaluminum, and diethoxyethylaluminum) and the surface of silica activated at various temperatures (200–800 °C) was studied by IR spectroscopy, mass spectrometry, and quantum chemistry. Formation of structural silanon defects on the surface of silica activated at 800 °C was considered. It was established that the fraction of terminal silanol groups involved in the interaction with organoaluminum compounds on the surface of silica thermoactivated above 600 °C is low, and siloxane bonds and structural surface defects play a determining role. The thermodynamic favorability of coordination of organoaluminum compounds on these active surface centers is shown. The structure and routes of decomposition of aluminum-containing surface intermediates were studied.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 10, pp. 1906–1911, October, 1995.The work was financially supported by the Russian Foundation for Basic Research (Project No. 94-03-08847).     

Capillary electrochromatography with monolithic-silica columns. II. Preparation of amphiphilic silica monoliths having surface-bound cationic octadecyl moieties and their chromatographic characterization and application to the separation of proteins and other neutral and charged species

Three different synthetic routes have been introduced and evaluated for the preparation of amphiphilic silica-based monoliths possessing surface-bound octadecyl ligands and positively charged groups. The amphiphilic silica monoliths (designated as cationic C18-monoliths) have been designed for use in reversed-phase capillary electrochromatography (RP-CEC) with hydro-organic mobile phases. These amphiphilic stationary phases yielded anodic electroosmotic flow (EOF) over a wide range of mobile phase pH. The magnitude of EOF remained constant up to pH 4.0 and then decreased at pH > 4.0 due to the ionization of silanol groups and the subsequent decrease in the net positive surface charge density of the amphiphilic monoliths. The cationic C18-monoliths exhibited reversed-phase chromatography (RPC) behavior toward non-polar solutes (e.g., alkyl benzenes), which parallels that observed with octadecyl-silica (ODS) monoliths. On the other hand, the amphiphilic stationary phases exhibited both non-polar and polar interactions toward slightly polar solutes such as anilines and PTH-amino acids. CEC retention factor k* and velocity factor k*e, which reflects the contribution of the electrophoretic mobility, were evaluated for charged solutes such as anilines and proteins.