Synthèse et stabilité sous irradiation électronique d'une céramique Ba1,16Al2,32Ti5,68O16 de structure hollandite envisagée pour le confinement de césium radioactif

Synthesis and stability under electron irradiation of a hollandite structure-type Ba_1.16Al_2.32Ti_5.68O₁₆ ceramic envisaged for radioactive cesium immobilization. Hollandite structure-type Ba_xCs_y(M,Ti)₈O₁₆ (x + y < 2, M trivalent cation) ceramics are currently envisaged as a specific waste form for radioactive cesium immobilization. In order to simulate the effect of cesium β decay on this kind of matrix, the structural modifications and the paramagnetic point defects induced by external electron irradiations near room temperature in a simplified Ba_1.16Al_2.32Ti_5.68O₁₆ hollandite composition were studied mainly by EPR and NMR. Modifications of Al³⁺ and Ti⁴⁺ ions' environment were observed and are due to both the formation of oxygen vacancies and to barium ions displacement. Electron (Ti³⁺) and hole (O₂⁻) centres were observed. The stability of these centres was good at room temperature but thermal treatments performed between 50 and 850 °C generated new paramagnetic defects originating from previous defects. These new defects correspond to titanyl-type Ti³⁺ ions located on grain surface and to oxygen aggregates in their bulk.     

Preparation and electrical properties of new oxide ion conductors Ce6−xDyxMoO15−δ (0.0 ≤ x ≤ 1.8)

Ce_6−xDy_xMoO_15−δ (0.0 ≤ x ≤ 1.8) were synthesized by modified sol–gel method. Structural and electrical properties were investigated by means of X-ray diffraction (XRD), Raman, X-ray photoelectron spectroscopy (XPS) and electrochemical impedance spectroscopy (EIS). The XRD patterns showed that the materials were single phase with a cubic fluorite structure. Impedance spectroscopy measurement in the temperature range between 350 °C and 800 °C indicated a sharp increase in conductivity for the system containing small amount of Dy₂O₃. The Ce_5.6Dy_0.4MoO_15−δ detected to be the best conducting phase with the highest conductivity (σ_t = 8.93 × 10⁻³ S cm⁻¹) is higher than that of Ce_5.6Sm_0.4MoO_15−δ (σ_t = 2.93 × 10⁻³ S cm⁻¹) at 800 °C, and the corresponding activation energy of Ce_5.6Dy_0.4MoO_15−δ (0.994 eV) is lower than that of Ce_5.6Sm_0.4MoO_15−δ (1.002 eV).     

Influence de certains ions inorganiques, de l'éthanol et du peroxyde d'hydrogène sur la photominéralisation du β-naphtol en présence de TiO2

TiO₂ photocatalytic mineralization of β-naphthol: influence of some inorganic ions, ethanol, and hydrogen peroxide. In this work, the photocatalytic oxidation of β-naphthol in aqueous suspensions of TiO₂ was investigated at room temperature, by following the formation of CO₂. The disappearance of β-naphthol fits a Langmuir-Hinshelwood kinetic model. The activation energy for the degradation reaction of β-naphthol is estimated at 10.2 kJ/mol. The effects of some additives such as ethanol, H₂O₂, and inorganic ions (Cl⁻, SO₄²⁻, HCO₃⁻, NO₃⁻, Fe³⁺, Cu^2+, and Cr³⁺) on the photomineralization of β-naphthol were examined. The inhibition of the anions for this reaction was in the order : NO₃⁻ < HCO₃⁻ < SO₄²⁻ < Cl⁻. This can be due to a partial blockage of catalyst active sites by these ions or their reaction with an oxidizing radical such as OH. The most photoactive systems for β-naphthol degradation were found in the presence of ferric ions, while the addition of Cr³⁺ strongly inhibited the photocatalytic decomposition of β-naphthol.     

The defect solid solution Na7/8(Fe7/8+xTi9/8−2xSbx)O4 (0 ≤ x ≤ 1/3): Evidence of Na mobility in the tunnels of a quadruple rutile-chain structure

A new defect solid solution, the series Na_7/8(Fe^III_7/8+xTi^IV_9/8−2xSb^V_x)O₄, was synthesized. Its homogeneity range is rather wide: 0 <- x ≤ 0.33. The incorporation of Sb^V gives rise to a progressive increase of the parameters of the orthorhombic unit cell. X-ray powder structure calculations point to a partial occupancy of the large double tunnels in a quadruple rutile-chain structure. A significant ordering of cations over the octahedral framework is observed, owing to a Ti^IV---Sb^V segregation. Electrical measurements emphasize a cationic conductivity, mainly related to a 1D motion of Na^I cations. A transition from a low activation energy process—E_A ≤ 0.20 eV—to a high activation energy one—E_A ≈ 0.75 eV—systematically occurs at T ≈ 440°C, independent of the Sb^V concentration. A possible skew motion from a half tunnel to another one is proposed as a tentative explanation of the high-temperature conductivity mechanism.     

Glass–ceramic Li2S–P2S5 electrolytes prepared by a single step ball billing process and their application for all-solid-state lithium–ion batteries

We report that glass–ceramic Li₂S–P₂S₅ electrolytes can be prepared by a single step ball milling (SSBM) process. Mechanical ball milling of the xLi₂S·(100 − x)P₂S₅ system at 55 °C produced crystalline glass–ceramic materials exhibiting high Li-ion conductivity over 10⁻³ S cm⁻¹ at room temperature with a wide electrochemical stability window of 5 V. Silicon nanoparticles were evaluated as anode material in a solid-state Li battery employing the glass–ceramic electrolyte produced by the SSBM process and showed outstanding cycling stability.     

Etude par RMN de 19F de la Solution Solide K1−xBixF1+2x et de la Phase Ordonnée KBi3F10

Study on the ¹⁹F NMR of the Solid Solution K_1?xBi_xF_1+2x and the ordered KBi₃F₁₀ phase KBi₃F₁₀ The solid solution K_1?xBi_xF_1+2x (0.50 ≤ x ≤ 0.70) and the ordered KBi₃F₁₀ phase have been investigated by ¹⁹F NMR. The evolution of the absorption spectra shows that the number of mobile F^? ions increases with temperature. The higher the fluorine concentration, the higher the temperature required to observe for all F^? ions a jump frequency exceeding dipolar frequency; it increases from 250 K for K_0.49Bi_0.51F_2.02 to 425 K for KBi₃F₁₀. The analysis of the results vs x confirms that the lower limit of the solid solution corresponds to 0.49 < x < 0.51. The results are consistent with a progressive extension of the local clustering of defects (F₈ cubes and F₁₂ cubooctahedra) up to formation of the long range ordered phase KBi₃F₁₀. Comparison with electrical conductivity measurements shows that the motions detected by NMR are diffusive ones.     

Etude des propriétés de conduction électrique des polyphosphates: Li3Ba2(PO3)7, LiPb2(PO3)5, LiCs(PO3)2, et αLiK(PO3)2

The electrical conductivity of the crystallized polyphosphates Li₃Ba₂(PO₃)₇, LiPb₂(PO₃)₅, LiCs(PO₃)₂, and αLiK(PO₃)₂ has been determined at different temperatures by impedance spectroscopy. The conductivity, σ, spreads within a range of 1.59 × 10⁻⁸ to 1.79 × 10⁻⁷ S cm⁻¹ at 573 K, and from 1.71 × 10⁻⁵ to 9.86 × 10⁻⁴ S cm⁻¹ at 773 K. The transport should be assumed in the majority by the lithium ions with regard to the structural characteristics of these polyphosphates. The results are discussed and compared to the conductivity properties of other lithium ion conductors.     

Sodium “stuffed” Ba2−xSrxFe4O8 ferrites: new cationic conductors

Sodium insertion in the tetrahedral layer structure of the ferrites Ba_2−xSr_xFe₄O₈ was performed by solid state reaction at 1220 K in air. Superstoichiometric oxides with the actual formula (Ba_2−xSr_x)_1−y/4Na_yFe₄O₈—y0.56; 0.60Ba/Sr1.67—were characterized by X-ray and neutron powder diffraction. The hexagonal unit-cell volume shows an increasing dependence on the sodium insertion when the Ba/Sr ratio reaches the largest values. The marked expansion of the c parameter is the likely signature of the location of the inserted sodium cations within the interlayer space. One-half of the sodium cations partly sits on the Sr(Ba) sites in octahedral coordination and the other half occupies extra octahedral and tetrahedral sites. ac conductivity measurements point to a cationic conductivity whose thermally activated regime—E_a 0.7 eV—evidenced from 570 K, is unsensitive to the sodium content. The bottleneck of the 2D sodium mobility regards the crossing of the oxygen triangular faces shared by the different polyhedra within the interlayer space.     

An optical, EPR and electrical conductivity study of blue barium titanate, BaTiO3−δ

The electronic UV–VIS–NIR absorption spectra of single crystalline BaTiO_3−δ (BTO) are studied in the temperature range of 102–1173 K in pure oxygen and at conditions of moderate and strong reduction of the material. The strongly reduced crystals are of deep blue colour. The optical spectra of blue BTO are characterised by a strong absorption in the NIR region at around 7000 cm⁻¹, which is attributed to polaronic defects associated with the formation of Ti³⁺ in the material. This assumption is supported by fits of the spectra using polaronic line shape functions appropriate for disordered systems and also by the electrical conductivity of blue BTO which, in agreement with results from the optical spectra, exhibits an activation energy of 0.20 eV. The EPR spectra of moderately reduced BTO powders show an anisotropic g-factor, which is compatible with the optical spectrum. The temperature dependence of the band gap energy of BTO was found to be given as dE_g/dT = −7.21 × 10⁻⁴ eV/K.     

Non-stoechiométrie dans le système FeF3---ZrF4

The FeF₃---ZrF₄ system has been investigated using X-ray diffraction, micro-DTA, magnetic measurements, and Mössbauer spectroscopy. At 850°C two solid solutions with formulas Fe_1−xZr_xF_3+x have been obtained, which are based on the VF₃ type for 0 ≤ x < 0.10 and on the ReO₃ type for 0.10 ≤ x ≤ 0.23, respectively. A phase transition occurs in the VF₃-type domain: the transition temperature decreases with increasing x. All phases exhibit an antiferromagnetic behavior. The thermal variation of Mössbauer parameters has been studied for x = 0.05 and x = 0.23 as well as their variation vs composition at 300 K. The magnetic behavior is discussed on the basis of the structural data presently available.     

Synthese et propriétés de conduction ionique des phases Li8−2xCaxCeO6 (0 < x ≤ 0,5) et Li6CaCeO6

The solid solution Li_8−2xCa_xCeO₆ (0 < x ≤ 0,5) and the definite phase Li₆CaCeO₆ have been obtained at 800°C through a study of Li---Ca---Ce---O system. Electrical measurements on the doped phases Li^tetr.₆ [Li_2-2xCa_xCe□]^oct.O₆ show that the conductivity varies slightly with the creation of vacancies in the octahedral layers. This result unambiguously confirms the following diffusion mechanism: the conduction is assumed essentially by lithium ions located in the tetrahedral layers. The compound Li₆CaCeO₆ is isostructural with Li₆In₂O₆. The cell is trigonal, Å, c = 10,603 Å, c/a = 1,058₇, and Z = 6. This new quaternary phase, which belongs to the same structural family of oxides of the type Li₈MO₆, either pure or doped with calcium, may be represented by the formula Li^tetr.₆[Ca Ce□]^oct.O₆. Electrical and structural data are correlated for this compound.     

Transport Properties of Bi2−xInxSe3 Single Crystals

The paper reports on the temperature dependence of the electrical and thermal conductivity, Hall constant, and Seebeck coefficient of Bi_2−xIn_xSe₃ (x=0, 0.2, 0.4) single crystals measured over the temperature range from 2 to 300 K. One single-valley conduction band model is used to interpret relations among transport coefficients. The data analysis relies on the use of a mixed carrier scattering mechanism consisting of acoustic scattering and scattering on ionized impurities. The effect of In incorporation into the Bi₂Se₃ crystal lattice on the individual components of thermal conductivity is evaluated and discussed.     

Dielectric and Raman studies on the solid solution (1−x)BaTiO3/xNaNbO3 ceramics

In order to elucidate the correlation between the relaxor type of phase transition and the percent of the A and B site substitution in the Ba_1−xNa_xTi_1−xNb_xO₃ solid solution, the dielectric permittivity was carried out in the temperature range 80–600 K. All ceramics of these solid solutions present a ferroelectric–paraelectric phase transition with relaxor and classical character depending on the value of x. With increasing x the three phase transition of pure BaTiO₃ are pinched into one rounded dielectric peak, and there is evidence for Vogel–Fulcher type relaxational freezing. Raman spectra of the x=0.3 and x=0.7 compositions taken at various temperatures and measured over the wavenumber range 100–1200 cm⁻¹ confirm that the first order scattering is dominant in phonon bands resulting from both ordered region and disordered matrix.     

Oxygen-deficient SrTiO3−x, X = 0.28, 0.17, and 0.08. Crystal growth, crystal structure, magnetic, and transport properties

The grossly nonstoichiometric perovskites SrTiO_3−x with x = 0.28, 0.17, and 0.08 were prepared from a reaction of Sr₂TiO₄, TiO, and TiO₂ at 1500°C. For x = 0.28 relatively large single crystals were obtained. Also for this sample the crystal symmetry was found to depend on the rate of cooling from the reaction temperature and the annealing conditions. Rapidly cooled samples are tetragonal a = 3.9177(3) Å, c = 3.8878(5) Å. Samples annealed in vacuum at temperatures of 1000 to 600°C are cubic a = 3.9075(3) Å with no change in cell volume. Single crystal data from a tetragonal sample indicate slight preferential occupancy of one oxygen position in P4/mmm. No evidence for any supercell due to defect ordering could be seen by TEM in either cubic or tetragonal samples. The x = 0.28 crystals show metallic resistivity, (300 K) = 6 × 10⁻⁴ ohm-cm and temperature-independent paramagnetism, χ_m = 118 × 10⁻⁶ cm³ mole⁻¹. Hall effect data from 300 to 4.2 K analyzed on a single carrier model give a temperature-independent n-type carrier density of 2.4 × 10²¹ cm⁻³. This is a factor of 3.9 less than that expected if the creation of each oxygen vacancy results in the production of two carriers in a single band. Hall data for x = 0.17 and 0.08 samples give similar results corresponding to densities of 2.1 and 1.4 × 10²¹ cm⁻³, respectively, in the same temperature range. These densities are 2.7 and 1.9 times less than the expected single-band value, respectively. Such results point to a two-band model with a large effective mass in one of the bands.     

A study of the perovskite solid solution series LaxSr1−xRuO3 and LaxCa1−xRuO3 by ruthenium-99 Mössbauer spectroscopy

The magnetic, electronic, and structural properties of the solid solutions La_xSr_1−xRuO₃ and La_xCa_1−xRuO₃ have been studied by ⁹⁹Ru Mössbauer spectroscopy and other techniques. The La_xCa_1−xRuO₃ phases are reported for the first time and have been shown by powder X-ray diffraction measurements to be orthorhombically distorted perovskites. Electrical resistivity measurements on compacted powders show that all the phases are metallic with p 10⁻³, ohm-cm. Progressive substitution of Sr²⁺ by La³⁺ in ferromagnetic SrRuO₃ leads to a rapid collapse of the magnetic hyper-fine splitting at 4.2°K. For x = 0.25 some ruthenium ions still experience a magnetic field but for 0.4 x 0.75 only single, narrow resonance lines are observed, consistent both with the complete removal of the ferromagnetism and with the presence of an averaged ruthenium oxidation state in each phase, i.e., La_x³⁺Sr_1−x²⁺Ru^(4−x)+O₃ rather than La_x³⁺Sr_1−x²⁺Ru_x³⁺Ru_1−x⁴⁺O₃. LaRuO₃ and CaRuO₃ both give essentially single-line spectra at 4.2°K, indicating that the ruthenium ions in these oxides are not involved in long-range antiferromagnetic order but are paramagnetic. The solid solutions La_xCa_1−xRuO₃ (0 < x 0.6) give sharp symmetrical singlets with chemical isomer shifts (relative to the Ru metal) which move progressively from the value characteristic of Ru⁴⁺ (−0.303 mm sec⁻¹) toward the value for Ru³⁺ (−0.557 mm sec⁻¹), consistent with the presence of intermediate ruthenium oxidation states in these phases also.     

Analysis of ;W and O NMR chemical shifts in polyoxometalates by extended Hückel mo calculations

The extended Hückel molecular orbital (EHMO) calculations have been carried out using cluster approach to polyoxo anions, i.e. calculations have been done for a single octahedron MO₆ of different symmetry and results have been used to analyze ¹⁸³ W and ¹⁷ O NMR spectra. Using five d→d* energy differences for the individual WO₆ the sum Σ1/ (E_d→E_d*) have been calculated and plotted against the ¹⁸³ W chemical shift (from +258 to −670 ppm) for corresponding type of tungsten atom and practically a linear correlation between two parameters have been observed. This points out the electronic nature of the ¹⁸³ W chemical shift. Similar correlation have been found for the ¹⁷O NMR chemical shifts (−90 to +800 ppm) when the plotted against product of the R⁻³ Σ1/ (E_p→E_p*) where the R⁻³ bond length of the corresponding W–O bond. Increasing the ¹⁸³ W nuclear magnetic shielding with the calculated electron population on tungsten atom for closely related anions has been observed, but no general tendency between δ and the calculated electronic charge if the symmetry of polyhedron is changed is expected.     

Mouvement du lithium dans deux nouvelles familles d'électrolytes solides: Les boracites Li4+xB7O12+x/2Cl et les halogénoborates de lithium vitreux

The boracites Li_4+xB₇O_12+x/2Cl and the related B₂O₃---xLi₂O---yLiCl glasses have been studied by cw and pulsed NMR between 130 and 500°K. Above 160°K the ⁷Li spectrum is composed of two lines: a broad one due to nonmobile Li⁺ ions and a narrow one due to diffusing Li⁺ with a hopping frequency greater than the dipolar frequency. The activation energy deduced from spin-lattice relaxation time measurements (T₁) is lower than that given by variation of conductivity with temperature. At low temperature T₁ disagrees with the BPP prediction (T₁ ω²_o). The diffusion process may be explained by the existence of a distribution of the local energy barriers.     

Crystal chemistry, modulated structure, and electrical conductivity in the oxygen excess scheelite-based compounds La1−xThxNbO4+x/2 and LaNb1−xWxO4+x/2

For La_1−xTh_xNbO_4+x/2, three phases with broad homogeneity regions occur, for 0.075 ≤ x ≤ 0.37, 0.41 < x < 0.61, and 0.65 ≤ x ≤ 0.74. All are related to the scheelite structure type, with at least the first exhibiting an incommensurate structural modulation. An analogous structurally modulated phase was found for LaNb_1−xW_xO_4+x/2 for 0.11 ≤ x ≤ 0.22. Additional phases occur at La_0.2Th_0.8NbO_4.4 and LaNb_0.4W_0.6O_4.3. The electrical conductivity and the direction and wavelength of the structural modulation have been characterized for the La_1−xTh_xNbO_4+x/2 phase with 0.075 ≤ x ≤ 0.37.     

Mössbauer study of the FeV2O4---Fe3O4 system

Mössbauer spectra of the Fe_1+xV_2−xO₄ spinel solid solutions are taken to investigate the cation distribution. Room temperature spectra can be interpreted by assuming that the cation distribution is represented approximately as Fe²⁺[Fe³⁺_xV³⁺_2−x]O₄ for 0 x 0.35 and Fe³⁺[Fe²⁺Fe³⁺_x−1V³⁺_2−x]O₄ for 1 x 2 and the ionic valence arrangement changes from the 2-3-3 type (Fe²⁺[Fe³⁺_xV³⁺_2−x]O₄) to the 3-2-3 one (Fe³⁺[Fe²⁺V³⁺]O₄) in the range 0.35 x 1. Fe₂VO₄ is found to be 3-2-3 spinel, Fe³⁺[Fe²⁺V³⁺]O₄. Its paramagnetic spectrum at 473°K is, however, composed of a broad single line with isomer shift value of 0.61 mm/sec relative to stainless steel, in which the line splitting due to the ferric and ferrous ions is rendered indistinguishable.     

Structure and Magnetism of Pr1−xSrxFeO3−δ

Crystal structure, redox, and magnetic properties for the Pr_1−xSr_xFeO_3−δ solid-solution phase have been studied. Oxidized samples (prepared in air at 900°C) crystallize in the GdFeO₃-type structure for 0≤x≤0.80, and probably in the Sr₈Fe₈O₂₃-type (unpublished) structure for x=0.90. Reduced samples (containing virtually only Fe³⁺) crystallize as the perovskite aristotype for x=0.50 and 0.67 with randomly distributed vacancies. The Fe⁴⁺ content increases linearly in the oxidized samples up to x≈0.70, whereupon it stabilizes at around 55%. Antiferromagnetic ordering of the G type is observed for oxidized samples (0≤x≤0.90) which show decreasing Néel temperature and ordered magnetic moment with increasing x, while the Néel temperature is nearly constant at 700 K for reduced samples. Electronic transitions for iron from an average-valence state via charge-separated to disproportionated states are proposed from anomalies in magnetic susceptibility curves in the temperature ranges 500–600 K and 150–185 K.