Sulfonated Poly(ether ether ketone) and Poly(ethylene glycol) Diacrylate Based Semi-Interpenetrating Network Membranes for Fuel Cells

Polymer electrolyte membranes are prepared from novel semi-interpenetrating polymer network material where the sulfonated poly (ether ether ketone) (SPEEK) is the linear polymer and the poly (ethylene glycol) diacrylate (PEGDA) is the cross-linking constituent. The semi-IPN is prepared by in situ polymerization of PEGDA in the presence of sulfonated poly (ether ether ketone). SPEEK is prepared by direct sulfonation of commercial PEEK (Gatone? 1100) by reported procedures. SPEEK with degree of sulfonation 63% (calculated from FT-NMR) is selected as the base membrane and different semi-IPN membranes were prepared by varying the PEGDA and SPEEK ratio. The degree of sulfonation of SPEEK and the formation of semi-IPN were confirmed by spectroscopy studies. The various semi-IPN membranes were characterized for ion-exchange capacity, water uptake, hydrolytic stability, proton conductivity and thermal stability for evaluating the suitability of these membranes for fuel cells. The proton conductivity of the membranes decreased with increasing PEGDA content. The Semi-IPN membranes exhibited conductivities (30°C) from 0.018 S/cm to 0.006 S/cm. These interpenetrating network membranes showed higher hydrolytic stability than the pure SPEEK membrane. This study shows that semi-IPN membranes based on PEGDA and SPEEK can be viable candidates for electrolyte membranes.     

Sulfonated poly(ether ether ketone) as an alternative charged material to poly(vinyl chloride) in the design of ion-selective electrodes

To date, poly(vinyl chloride) (PVC) is the most used polymer in the design of ion selective electrode (ISE) membranes. This paper is focused on the use of sulfonated poly(ether ether ketone) (SPEEK) as an alternative material to PVC for the design of ISEs. SPEEK of the desired degree of sulfonation is synthesized from poly(ether ether ketone) (PEEK). An NH₄⁺-ISE has been chosen as a model electrode to study the efficiency of SPEEK as polymer matrix of the membrane. The material was evaluated in ionophore free ion exchanger membranes as well as in ion-selective electrodes membranes containing nonactine as ionophore. Analytical performance parameters of the prepared electrodes were evaluated. The electrodes show a slope between 50 and 60 mV dec⁻¹ depending on both the calibration medium and the membrane composition. A linear range of response between 10⁻⁴ and 1.0 M and a lifetime of 1-2 months were obtained. The interferences of cations such us Ca²⁺, Na⁺, Li⁺ and K⁺ over the prepared ISEs are studied as well. Although the plasticizer in the SPEEK based membrane matrix is not necessary, its presence improves the sensibility. This makes SPEEK a good potential choice over alternative membrane matrices reported in the literature and a promising platform for the establishment of membrane components.     

可逆加成-断裂链转移自由基聚合法合成梳型磺化聚醚醚酮

以带双硫酯取代基聚醚醚酮为大分子链转移剂, 采用可逆加成-断裂链转移自由基聚合(RAFT)法合成不同接枝率的磺化聚醚醚酮(g-SPEEK), 并对其结构进行表征. 在单体/链转移剂/引发剂的投料比(摩尔比)为50:4:1, 温度为70 ℃, 反应24 h, 得到聚合物膜的离子交换容量和吸水率分别为1.312 mmol/g和43.51%, 其溶胀率为5.05%, 低于Nafion膜的11.50%. 热重分析(TGA)结果表明该梳型g-SPEEK具有较好的热力学稳定性, 且该聚合物膜具有与Nafion膜相当的抗氧化性. 在相同的离子交换容量下, 梳型g-SPEEK比主链型SPEEK具有更好的H⁺离子透过性能.     

Proton exchange membrane using partially sulfonated polystyrene-b-poly(dimethylsiloxane) for direct methanol fuel cell

A diblock copolymer ionomer containing a rubbery poly(dimethylsiloxane) block has been developed as a proton exchange membrane for direct methanol fuel cell (DMFC). The partially sulfonated polystyrene-b-poly(dimethylsiloxane) (sPS-b-PDMS) membrane with 38% sulfonation degree exhibited 3 times lower methanol permeability and 2.6 times higher membrane selectivity (proton conductivity/methanol permeability) compared to Nafion^® 115 at 25 °C. Coexistence of microphase domains and ionic clusters was confirmed from the morphological studies by small-angle X-ray scattering and tapping-mode atomic force microscopy. Gas chromatographic analysis revealed that water/methanol selectivity of sPS-b-PDMS was 20 times higher than that of Nafion^® 115. Such a high water/methanol selectivity can be attributed to the existence of PDMS microdomains minimizing methanol permeation through hydrophilic ion channels. sPS-b-PDMS membranes were fabricated into membrane electrode assembly (MEA), and air-breathing DMFC test for these MEAs showed a better performance compared to the MEA composed of Nafion^® 115.     

Surface redox polymerized SPEEK–MO2–PANI (M = Si, Zr and Ti) composite polyelectrolyte membranes impervious to methanol

We reported sulfonated poly(ether ether ketone) (SPEEK, 61% degree of sulfonation)–metal oxides (MO₂:SiO₂, TiO₂ and ZrO₂)–polyaniline composite membranes. Metal oxides were incorporated into the swelled SPEEK membrane by sol–gel method and cured by thermal treatment. SPEEK–metal oxide membranes surfaces were modified with polyaniline (PANI) by a redox polymerization process. It was observed that water retention capacity of membrane was increased and methanol permeability was reduced due to synergetic effect of metal oxides and surface modification with polyaniline. These composite membranes showed extremely low methanol permeability (1.9–1.3 × 10⁻⁷ cm² s⁻¹), which was lower than till reported values either for SPEEK–metal oxide or SPEEK/PANI membranes. Relatively high selectivity parameter (SP) values at 343 K of these membranes, especially S–SiO₂–PANI and S–TiO₂–PANI, indicated their great advantages over Nafion117 (N117) membrane for targeting on moderate temperature applications due to the synergetic effect of MO₂ and PANI in SPEEK matrix. S–TiO₂–PANI and N117 showed comparable cell performance in direct methanol fuel cell (DMFC).     

Preliminary evaluation of sulfonated poly(ether ether ketone)/monoethanolamine/adipic acid composite membranes for direct methanol fuel cell applications

A series of sulfonated poly(ether ether ketone)/monoethanolamine/adipic acid (SPEEK/MEA/AA) composite membranes are prepared and investigated to assess their possibility as proton exchange membranes in direct methanol fuel cells (DMFCs). A preliminary evaluation shows that introducing MEA and AA into SPEEK matrix decreases the thermal stability of membrane. However, the degradation temperatures are still above 260 °C, satisfying the requirement for fuel cell operation. Compared with the pure SPEEK membrane, the composite membranes exhibit not only lower water uptake and swelling ratios but also better mechanical property and oxidative stability. Noticeably, the methanol diffusion coefficient of the composite membranes decrease significantly from 3.15 × 10^?6 to 0.76 × 10^?6 cm²/s with increasing MEA and AA content, accompanied by only a small sacrifice in proton conductivity. Although both the methanol diffusion coefficient and the proton conductivity of composite membranes are lower than those of pure SPEEK and Nafion® 117 membranes, their selectivity (conductivity/methanol diffusion coefficient) are higher. In addition, the composite membranes show excellent stability in aqueous methanol solution. The good thermal and chemical stability, low swelling ratio, excellent mechanical property, low methanol diffusion coefficient, and high selectivity make the use of these composite membranes in DMFCs quite attractive. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2871–2879, 2007     

Sulfonated poly(ether ether ketone)/polyaniline composite proton-exchange membrane

Sulfonated poly(ether ether ketone) (PEEK) was prepared by sulfonation of commercial Victrex^@ PEEK and degree of sulfonation was found to be about 44.5% by ¹H NMR. Sulfonated PEEK/polyaniline composite membranes, in order to prevent methanol crossover, were prepared by chemical polymerization of a thin layer of polyaniline (PANI) in the presence of a high oxidant concentration on a single face modification. FTIR and PANI coating density studies confirmed the loading of PANI in sulfonated PEEK membrane matrix. PANI composite membranes with different polymerization time were prepared and subjected to thermogravimetric analysis as well as electrochemical and methanol permeability study to compare with sulfonated PEEK and Nafion 117 membrane. Ion-exchange capacity, water uptake, proton transport numbers and proton conductivities for different PANI composite sulfonated PEEK (SPEEK) membranes were found to be dependent on the coating density of the PANI in the membrane matrix and were slightly lower than that of Nafion 117 membrane. Methanol permeability of these membranes (especially SPEEK/PANI-1.5) was about four times lower than Nafion 117 membrane. Among the all SPEEK membranes synthesized in this study, SPEEK-1.5 appears to be more suitable for direct methanol fuel cell (DMFC) application considering optimum physicochemical and electrochemical properties, thermal stability as well as very low methanol permeability. Above all, the cost-effective and simple fabrication technique involved in the synthesis of such composite membranes makes their applicability quite attractive.     

Crosslinking of sulphonated poly (ether ether ketone) using aromatic bis(hydroxymethyl) compound

2,6-Bis(hydroxymethyl)-4-methyl phenol and 1,4-bis(hydroxymethyl) benzene have been used as crosslinkers in sulphonated poly (ether ether ketone) (SPEEK DS 65%, IEC 1.84 mequiv./g) for the preparation of proton exchange membranes (PEMs). Crosslinking of SPEEK has been achieved by thermally activated bridging of the polymer chain with the hydroxymethyl group of crosslinker through condensation reaction with sulphonic acid group. The physico-chemical properties of uncrosslinked and crosslinked membrane were evaluated in terms of ion exchange capacity (IEC), water uptake, ionic conductivity and mechanical properties. The crosslinked membrane showed controlled swelling, ionic conductivity of 25–50 mS/cm at 80 °C and good mechanical properties. The chemical stability of the crosslinked membranes was studied by Fenton's test. The % loss in weight and changes in physico-chemical properties of the treated membranes were determined.     

自交联型磺化聚醚醚酮质子交换膜的合成

以含3,3'-二烯丙基双酚 A 结构单元的聚醚醚酮为基膜材料, 通过自由基加成反应在取代基上引入磺酸基团, 合成侧链型磺化聚醚醚酮(SPEEK)质子交换膜. 用傅里叶变换红外(FTIR)光谱、 核磁共振氢谱(¹H NMR)、 热重分析(TG)和扫描电子显微镜(SEM)等方法对 SPEEK 的结构进行表征. 实验结果表明, 巯基丙磺酸被接枝在聚醚醚酮侧基上, SPEEK 膜具有明显的亲水疏水微相分离形貌, 磺酸基团相互聚集形成离子通道. SPEEK 膜离子交换容量为 2.12 mmol/g, 钒离子渗透率为 1.54×10^-6 cm²/min, 低于Nafion117 膜的钒离子渗透率, 阻钒能力优于 Nafion117 膜. 以 SPEEK-4 膜组装电池的自放电时间约为130 h, 长于 Nafion117 膜的 66 h. 电池充放电循环 50 次, SPEEK-4 膜的库仑效率、 电压效率和能量效率没有明显降低, 显示出良好的稳定性.     

全钒液流电池用磺化聚醚醚酮/锂皂石质子膜的结构及性能

通过溶液流延法制备了磺化聚醚醚酮/锂皂石(SPEEK/Lap)复合膜, 对其物理化学性质、 机械性能、 化学稳定性及单电池性能进行了测试. 在SPEEK基质中引入的Lap有效改善了复合膜的质子传导率、 溶胀率和机械性能. 当Lap添加量(质量分数)从0.2%增到1.5%时, 复合膜的质子传导率随之增加(19.9~23.6 mS/cm). SPEEK/Lap-0.2复合膜的自放电时间为57.2 h, 是Nafion 117膜的2.4倍和纯SPEEK膜的1.5倍. 在80 mA/cm ²电流密度下, SPEEK/Lap-0.2复合膜的电压效率(VE, 86.5%)和能量效率(EE, 84.0%)明显高于Nafion 117膜(VE: 83.8%, EE: 80.7%)和纯SPEEK膜(VE: 81.4%, EE: 78.9%). 同时, SPEEK/Lap-0.2复合膜经100次充放电循环测试后具有良好的循环稳定性和结构稳定性.     

Methanol permeability in sulfonated poly(etheretherketone) membranes: A comparison with Nafion membranes

Partially sulfonated poly(etheretherketone) (SPEEK) samples were prepared by modification of corresponding poly(etheretherketone) (PEEK) with concentrated sulfuric acid. Membranes cast from these materials were evaluated as polymer electrolytes for direct methanol fuel cells (DMFCs). SPEEK membranes were characterized by ¹H NMR, FT-IR and TGA. The transverse proton conductivities increased from 4.1 to 9.3 × 10⁻³ S/cm with the increase of the degree of sulfonation (DS) from 0.59 to 0.93. These values were comparable with that of Nafion 117 membrane (1.0 × 10⁻² S/cm) measured under the same condition. Nearly one order magnitude difference between transverse conductivity and longitudinal conductivity was found. The methanol permeabilities of the SPEEK membranes were all lower than that of Nafion 117 membrane. The effects of temperature and methanol concentration on the methanol permeability were also studied. In addition, the selectivities of the SPEEK membranes for protons and methanol were all higher than that of Nafion 117 membrane.     

Polyaniline decorated graphene oxide on sulfonated poly(ether ether ketone) membrane for direct methanol fuel cells application

In direct methanol fuel cells (DMFC), methanol crossover is a major issue which has reduced the performance of polymer electrolyte membrane (PEM) for energy generation. In this study, graphene oxide (GO) and conductive polyaniline decorated GO (PANI-GO) were used as additives in fabrication of sulfonated poly(ether ether ketone) (SPEEK) nanocomposite PEM membrane to reduce methanol crossover. PANI-GO was synthesized by in situ polymerization method and the formation of PANI coated GO nanostructures was confirmed by surface morphology and crystallinity analysis. The membrane morphology and topography analysis confirmed that GO and PANI-GO were well dispersed on the surface of SPEEK membrane. 0.1 wt% PANI-GO modified SPEEK nanocomposite membrane exhibited the highest water uptake and ion exchange capacity of 40% and 1.74 meq g^?1, respectively. The oxidative stability of the nanocomposite membranes also improved. Lower methanol permeability of 4.33 × 10^?7 cm^?2S^?1 was noticed for 0.1 wt% PANI-GO modified SPEEK membrane. PANI-GO modified SPEEK membrane enhanced the proton conductivity, which was due to the existence of acidic and hydrophilic group present in PANI and GO. PANI-GO modified SPEEK membrane held higher selectivity of 1.94 × 10⁴ S cm^?3 s^?1. Overall, these studies revealed that PANI-GO modified SPEEK membrane is a potential material for DMFC applications.     

Preparation and characterization of monovalent cation selective sulfonated poly(ether ether ketone) and poly(ether sulfone) composite membranes

Highly charged cation permeable composite membranes were prepared by blending of sulfonated poly(ether sulfone) (SPES) with sulfonated poly(ether ether ketone) (SPEEK) in 0 to 90% weight ratio, to adjust the hydrophobic properties and ion selective nature. Extent of sulfonation was confirmed by 1H NMR and ion exchange capacity and degree of sulfonation depending on blending composition. These membranes were characterized as a function of weight fraction of SPEEK by recording ion-exchange capacity, water uptake, thermogravimetric analysis, membrane conductivity and membrane potential in equilibration with different electrolytic solutions. Membrane permselectivity and solute flux were estimated using these data on the basis of non-equilibrium thermodynamic principles and for observing the selectivity of different membranes for mono- or bivalent counter-ions. It was observed that relative selectivity for monovalent in comparison to bivalent counter-ions were increased with the decrease in SPEEK content in the composite membrane matrix. The range of SPEEK content in the blend from 60 to 80% appears the most suitable for the selective separation of monovalent ions from bivalent ions. Furthermore, highly charged nature and stabilities of these membranes extend their applications for the electro-assisted separations of similarly charged ions as well as other electro-membrane processes.     

Proton‐conducting electrolytes based on silylated and sulfonated polyetheretherketone: Synthesis and characterization

A derivative of polyetheretherketone (PEEK) having sulfonic acid groups and silicon‐containing substituents covalently bound to the aromatic backbone has been prepared as proton‐exchange membrane material. The polymer 4 (PhSiSPEEK) has been synthesized via (i) sulfonation of PEEK up to 0.9 degree of sulfonation (DS, the number of sulfonic groups per repeat unit), (ii) conversion of sulfonated PEEK 1 (SPEEK09) into sulfonyl chlorinated derivative 2 (PEEKSO₂Cl), (iii) lithiation of 2 and subsequent addition of PhSiCl₃, followed by hydrolysis. The chemical structure of the synthesized polymers has been investigated by ¹H NMR and ¹³C NMR and ATR/FTIR spectroscopy and their thermal stability has been evaluated by thermogravimetric analysis. The presence of inorganic moieties increases the thermal stability of 4 with respect to the sulfonated and not silylated product. Despite its very high DS, PhSiSPEEK is insoluble in water but does not possess the plastic properties needed to be used as an electrolyte membrane. Blend membranes made of SPEEK05 (DS = 0.5) and containing 10 and 25 wt % of 4 (DS = 0.9, degree of silylation DSi = 0.1) have been prepared and characterized by water uptake measurements and electrochemical impedance spectroscopy. The combination of the two functionalized polymers having different properties allows to obtain proton‐conducting electrolytes that are potential candidates for fuel cells applications. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2178–2186, 2010     

Proton and methanol transport behavior of SPEEK/TPA/MCM-41 composite membranes for fuel cell application

This paper reports proton and methanol transport behavior of composite membranes prepared for use in the direct methanol fuel cell (DMFC). The composite membranes were prepared by embedding various proportions (10–30 wt.%) of inorganic proton conducting material (tungstophosphoric acid (TPA)/MCM-41) into sulfonated poly(ether ether ketone) (SPEEK) polymer matrix. The results indicate that the proton conductivity of the membranes increases with increasing loading of solid proton conducting material. The highest conductivity value of 2.75 mS/cm was obtained for the SPEEK composite membrane containing 30 wt.% solid proton conducting material (50 wt.% TPA in MCM-41). The methanol permeability and crossover flux were also found to increase with increasing loading of the solid proton conducting material. Lowest permeability value of 5.7 × 10⁻⁹ cm² s⁻¹ was obtained for composite membrane with 10 wt.% of the solid proton conducting material (40 wt.% TPA in MCM-41). However, all the composite membranes showed higher selectivity (ratio between the proton conductivity and the methanol permeability) compared to the pure SPEEK membrane. In addition, the membranes are thermally stable up to 160 °C. Thus, these membranes have potential to be considered for use in direct methanol fuel cell.     

Preparation and characterization of layer‐by‐layer self‐assembly membrane based on sulfonated polyetheretherketone and polyurethane for high‐temperature proton exchange membrane

A concept of preparing high‐temperature proton exchange membranes with layer‐by‐layer (LBL) self‐assembly technique was proposed and the sulfonated polyetheretherketone (SPEEK) and polyurethane (PU) with 200 LBL deposition cycles denoting (SPEEK/PU)₂₀₀ membrane was prepared in this research. Owing to the strong electrostatic interaction between ? group in SPEEK and ? C? N⁺ group in PU, (SPEEK/PU)₂₀₀ membrane with LBL self‐assembly structure showed a favorable structural stability. The phosphoric acid (PA)‐doped (SPEEK/PU)₂₀₀ membrane showed a higher proton conductivity relative to PA doped SPEEK/PU membrane by solution casting method (SPEEK/PU)₂₀₀/40%PA membrane possessed a proton conductivity value of 2.90 × 10^?2 S/cm at 150 °C under anhydrous conditions. The LBL self‐assembly structure provided a possibility to reduce the negative effect from polymer skeleton blocking charge carrier species even immobilizing protons. Moreover, the (SPEEK/PU)₂₀₀ membrane presented the particularly noteworthy mechanical property even with PA doping. The tensile stress values at break were 72.8 and 24.1 MPa, respectively, for (SPEEK/PU)₂₀₀ and (SPEEK/PU)₂₀₀/40%PA membrane at room temperature, which were obviously higher than the reported values of 15.9 and 2.81 MPa for SPEEK/PU and SPEEK/PU/60%PA membrane. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 3446–3454     

Characterization and performance of proton exchange membranes for direct methanol fuel cell: Blending of sulfonated poly(ether ether ketone) with charged surface modifying macromolecule

Modification of sulfonated poly(ether ether ketone) (SPEEK) membrane was attempted by blending charged surface modifying macromolecule (cSMM). The modified membrane was tested for direct methanol fuel cell (DMFC) application; i.e. a SPEEK/cSMM blend membrane was compared to a SPEEK membrane and a Nafion 112 membrane for the thermal and mechanical stability, methanol permeability, and proton conductivity. Thermal and mechanical stability of the blended membrane were slightly reduced from the SPEEK membrane but still higher than the Nafion 112 membrane. The blend membrane was found to be promising for DMFC applications because of its lower methanol diffusivity (2.75 × 10⁻⁷ cm² s⁻¹) and higher proton conductivity (6.4 × 10⁻³ S cm⁻¹), than the SPEEK membrane. A plausible explanation was given for the favorable effect of cSMM blending.     

Sulfonated poly(ether ether ketone) composite membranes based on amino-modified halloysite nanotubes that effectively immobilize phosphotungstic acid

In this work, we prepared amino-modified halloysite nanotubes (PEI-DHNTs) via the co-deposition of self-polymerized dopamine and polyethylenimine (PEI) on the surface of nanotubes, which was confirmed by X-ray photoelectron spectroscopy (XPS) and Thermogravimetric analysis (TGA). A series of composite proton exchange membranes (PEMs) were prepared by incorporating PEI-DHNTs and phosphotungstic acid (HPW) into sulfonated poly(ether ether ketone) (SPEEK). It was found that both PEI-DHNTs and HPW were well dispersed in the polymer matrix, exhibiting excellent filler-matrix compatibility. The composite membranes demonstrated enhanced proton conductivity, reaching as high as 0.078 S cm⁻¹ with 33.3 wt.% HPW loading, which was ~90% higher than that of SPEEK control membrane. Such improvement was mainly attributed to the strong acid–base pairs formed by PEI-DHNT with both SPEEK and HPW, which shortened proton hopping distance and created more continuous proton conduction pathways. Furthermore, the membrane conductivity remained almost constant after 1 year's immersion in liquid water, indicating the successful immobilization of HPW in the composite membranes.     

不同磺化度下的磺化聚醚醚酮对全钒储能液流电池性质影响的研究

本文报道了采用浓硫酸作为磺化剂,成功合成了不同磺化度下的聚醚醚酮(PEEK)膜,并深入研究了磺化条件包括磺化时间和磺化剂的用量对所获薄膜性能的影响,获得了在不同磺化度（DS）下SPPEK膜的离子交换容,含水率,机械性能,质子电导率等参数,特别测定了在全钒液流电池工作条件下钒离子(Ⅳ)渗透率,首次为该类液流储能电池使用价廉质优的质子交换膜提供了基础实验数据。室温条件下的实验结果如下：1）磺化12小时后,膜的磺化度46%,含水量为28%,钒离子(Ⅳ)选择性最佳（钒离子渗透率为1.2×10-7 cm2/min-1,是Nafion117 (2.9×10-6 cm2/min-1)的1/24）,其质子电导率只有0.02 S/cm;2）磺化96小时其磺化度达79%的膜,质子电导率达0.16 S/cm,是Nafion117 (0.10S/cm) 的1.6倍, 但其机械性能最差;3）与Nafion117膜相比,磺化在36到48小时的SPPEK膜其机械力学性能好,薄膜的钒离子渗透率、离子交换容IEC、质子导电率和含水率高,且对钒离子的选择性佳,尤其价格仅为Nafion膜的1/13,是理想的Nafion膜的代替物,可望直接应用于全钒氧化还原液流（VRB）电池中。本文还讨论了磺化时间和不同磺化剂量对膜的性质的影响。     

Novel multiblock‐co‐ionomers as potential polymer electrolyte membrane materials

In this contribution a series of novel multiblock‐co‐ionomers consisting of hydrophobic (partially fluorinated) and hydrophilic (sulfonated) domains has been prepared and characterised in terms of their applicability as fuel cell membranes. The synthesis of these multiblock‐co‐ionomers is a four‐step procedure including (1) the sulfonation of the monomer 4,4′‐difluorodiphenylsulfone, (2) the preparation of hydrophilic telechelic macromonomers by molecular‐weight controlled step‐growth polycondensation of the sulfonated monomer with various bis(thio)phenols, (3) the preparation of a hydrophobic telechelic macromonomer and (4) the coupling of both telechelic macromonomers to yield microphase‐separated block‐co‐ionomers. This study focuses on the investigation of the influence of various linkage groups and atoms within the hydrophilic domains of the multiblock‐co‐ionomers. Both the telechelic macromonomers and the multiblock‐co‐ionomers were structurally investigated by ¹H‐ and ¹⁹F‐NMR spectroscopy and gel permeation chromatography (GPC). All multiblock‐co‐ionomers of this series could be cast into membranes and their membrane properties (ion‐exchange capacity, specific resistance, swelling ratio, water uptake, thermal and oxidative stability) were measured and discussed in dependence of the various linkage groups within the hydrophilic domains. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5237–5255, 2007