Nanocomposite films based on TEMPO-mediated oxidized bacterial cellulose and chitosan

Nanobacterial cellulose (BC) and chitosan (CH) have similar molecular structures. In the present work, nanocomposite films based on BC and CH were prepared by stepwise modification instead of by conventional physical blending. First, surface C6-carboxylated BC was prepared in a bromide-free system using 2,2,6,6-tetramethylpyperidine-1-oxyl (TEMPO) as a catalyst. The carboxylate groups of oxidised BC could couple to the amine groups of CH. The composite films were characterised by attenuated total reflectance Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy and Carbon-13 solid nuclear magnetic resonance ¹³C NMR. The results showed that a cross-linking reaction occurred between TEMPO-mediated oxidised BC and CH. Even in the absence of cross-linkers, these two biopolymers could interact with each other because of their structural similarity. SEM images and tensile tests showed that the TEMPO-oxidized BC and CH composite film prepared at a 0.5:1 ratio was an exception. The mechanical properties of the composite films decreased with increasing CH content, passed through a minimum, and then increased. To explain this phenomenon, we propose that the hydrogen bonding in the original BC microstructure plays a decisive role in the modified nanocomposites. However, BC/CH composites with excellent properties could be synthesised at appropriate reactant ratios.     

Wettability and surface composition of partly and fully regenerated cellulose thin films from trimethylsilyl cellulose

The wettability and surface free energy (SFE) of partly and fully regenerated cellulose model surfaces from spin coated trimethylsilyl cellulose were determined by static contact angle (SCA) measurements. In order to gain detailed insight into the desilylation reaction of the surfaces the results from SCA measurements were compared with data from other surface analytical methods, namely thickness measurements, X-ray photoelectron spectroscopy (XPS) and attenuated total reflectance infrared spectroscopy (ATR-IR). Additionally, the influence of ultra high vacuum treatment (UHV) during XPS measurements on the water wettability and surface morphology of regenerated cellulose thin films was investigated. The wetting of polar and non-polar liquids increased with prolonged regeneration time, which is reflected in the higher SFE values and polarities of the films. After UHV treatment the water SCA of partly regenerated films decreases, whereas fully regenerated cellulose shows a higher water SCA. Therefore it is assumed that volatile desilylation products tend to adsorb on partly regenerated films, which strongly influences their wettability.     

The thermal degradation property and flame-retardant mechanism of coated knitted cotton fabric with chitosan and APP by LBL assembly

Journal of Thermal Analysis and Calorimetry - In order to improve the flame retardancy of knitted cotton fabrics and investigate the flame-retardant mechanism of the system formed by ammonium...     

Layer-by-layer films of hemoglobin or myoglobin assembled with zeolite particles: electrochemistry and electrocatalysis

Positively charged hemoglobin (Hb) or myoglobin (Mb) at pH 5.0 in solutions and negatively charged zeolite particles in dispersions were alternately adsorbed onto solid surfaces forming [zeolite/protein](n) layer-by-layer films, which was confirmed by quartz crystal microbalance (QCM) and cyclic voltammetry (CV). The protein films assembled on pyrolytic graphite (PG) electrodes exhibited a pair of well-defined, nearly reversible CV peaks at about -0.35 V vs. SCE at pH 7.0, characteristic of the heme Fe(III)/Fe(II) redox couples. Hydrogen peroxide (H(2)O(2)) and nitrite (NO(2)(-)) in solution were catalytically reduced at [zeolite/protein](7) film modified electrodes, and could be quantitatively determined by CV and amperometry. The shape and position of infrared amide I and II bands of Hb or Mb in [zeolite/protein](7) films suggest that the proteins retain their near-native structure in the films. The penetration experiments of Fe(CN)(6)(3-) as the electroactive probe into these films and scanning electron microscopy (SEM) results indicate that the films possess a great amount of pores or channels. The porous structure of ]zeolite/protein](n) films is beneficial to counterion transport, which is crucial for protein electrochemistry in films controlled by the charge-hopping mechanism, and is also helpful for the diffusion of catalysis substrates into the films. The proteins with negatively charged net surface charges at pH 9.0 were also successfully assembled with like-charged zeolite particles into layer-by-layer films, although the adsorption amount was less than that assembled at pH 5.0. The possible reasons for this were discussed, and the driving forces were explored.     

Layer-by-layer assembly of cationic guar gum,cellulose nanocrystals and hydroxypropyl methylcellulose based multilayered composite films

Eco-friendly sustainable materials provide an appealing template to replace contemporary synthetic-nonrenewable resource-based materials while maintaining the acceptable material properties to meet the performance requirements. Here, a layer-by-layer (LBL) self-assembly technique was used for fabricating multilayer composite films using all bio-based polymers/polysaccharides, i.e. cationic guar gum (CGg), carboxylated cellulose nanocrystals (cCNCs) and hydroxypropyl methylcellulose (HPMC). A five layered composite film was fabricated by depositing polymeric layers as follows: CGg→cCNCs→HPMC→cCNCs→CGg. The structural analysis of (CGg/cCNCs/HPMC)_5 L multilayered composite films indicated the existence of electrostatic interaction as well as H-bonding between polymeric layers that resulted in homogenous, dense and compact film surface with improved smoothness and strength properties. As compared to pure CGg film, the (CGg/cCNCs/HPMC)_5 L multilayered composite films showed improved tensile strength (84.8?% increment) and modulus (29.19?% improvement). Importantly, the deposition of HPMC layer contributed in achieving multilayer composite films with more flexible behavior (46.55?% improvement in elongation at break). Furthermore, owing to the high transparency (89.5?% transmittance), appreciable gas and oil barrier performance and resistance to various solvents (e.g. acetone, THF and DMAc), these multilayer films are promising candidates for various applications including renewable/sustainable packaging materials.

     

Preparation and properties of epichlorohydrin-cross-linked chitosan/hydroxyethyl cellulose based CuO nanocomposite films

This study introduces an effective route to fabricate chitosan (CS)-based film. The films were prepared through cross-linking reaction between CS and hydroxyethyl cellulose (HEC) using epichlorohydrin (ECH) as the cross-linker and simultaneously in-situ loading with CuO nanoparticles. FT-IR and loading efficiency results indicated the occurrence of inter- and intra-molecular cross-linking reaction between CS and HEC. XRD and EDS analyses showed that the CuO nanoparticles were evenly deposited onto CS film matrixes. SEM characterization showed that the films were of compact, dense and uniform cross morphologies, as well as obvious voids. The films also exhibited desired swelling ratio and water vapor permeability. The enhanced tensile strength was obtained with a maximum value of 77.02?±?3.26 MPa, while the stretch-ability slightly decreased. The thermal stability of the films decreased after cross-linking with HEC. The antibacterial ability of the films was generally improved with the increase of HEC and ECH contents.

Graphical abstract

Preparation and properties of epichlorohydrin-cross-linked chitosan/hydroxyethyl cellulose based CuO nanocomposite films

     

Layer-by-layer assembled microgel films with high loading capacity: reversible loading and release of dyes and nanoparticles

Multilayer films containing microgels of chemically cross-linked poly(allylamine hydrochloride) (PAH) and dextran (named PAH-D) were fabricated by layer-by-layer deposition of PAH-D and poly(styrene sulfonate) (PSS). The successful fabrication of PAH-D/PSS multilayer films was verified by quartz crystal microbalance measurements and cross-sectional scanning electron microscopy. The as-prepared PAH-D/PSS multilayer films can reversibly load and release negatively charged dyes such as methyl orange (MO) and fluorescein sodium and mercaptoacetic acid-stabilized CdTe nanoparticles. The loading capacity of the film for MO can be as large as approximately 3.0 microg/cm2 per bilayer, which corresponds to a MO density of 0.75 g/cm3 in the film. The high loading capacity of the PAH-D/PSS films originates from the cross-linked film structure with sufficient binding groups of protonated amine groups, as well as their high swelling capability by solvent. The loaded material can be released slowly when immersing the films in 0.9% normal saline. Meanwhile, the PAH-D/PSS multilayer films could deposit directly on either hydrophilic or hydrophobic substrates such as quartz, polytetrafluoroethylene, polystyrene, poly(ethylene terephthalate), and polypropylene. The microgel films of PAH-D/PSS are expected to be widely useful as matrixes for loading functional guest materials and even for controlled release.     

Flame retardancy and thermal degradation of halogen-free flame-retardant biobased polyurethane composites based on ammonium polyphosphate and aluminium hypophosphite

In this work, based on castor oil (CO), flame retardant polyurethane sealants (FRPUS) with ammonium polyphosphate (APP) and aluminum hypophosphite (AHP) were prepared. The synergistic flame retardant effects between APP and AHP on flame retardancy, thermal stability, and flame retardant mechanisms of FRPUS were investigated. It was found that when the mass ratio of APP and AHP was 5:1, the limiting oxygen index (LOI) value of FRPUS increased to 35.1%, In addition, at this ratio, the parameters from cone calorimeter testing (CCT) were reduced; these parameters include peak heat release rate (PHRR), total heat release (THR), smoke production rate (SPR) and total smoke production (TSP). The thermal decomposition behavior of the FRPUS was investigated by thermogravimetric analysis (TGA). The results showed that AHP improved the thermal stability of the PUS/APP system and increased char residue at high temperatures. Moreover, the residual carbon was investigated by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and scanning electron microscope (SEM), gas phase pyrolysis products were investigated by thermogravimetric analysis/infrared spectrometry (TG-IR) and thermogravimetric analysis/mass spectrometry (TG-MS). It was observed that the flame retardant mechanisms of the APP/AHP system was the combination of gas and condensed phase flame retardant mechanisms.     

Disperse dyes based on 2-aminothiazole derivatives for cellulose triacetate fabric

A range of azo disperse dyes was prepared by coupling diazotized 2-amino-4-(p-nitrophenyl)-5-nitrothiazole with various substituted arylamines. Spectral properties in the infrared and visible range of the dyes obtained were investigated. All the dyes, when applied on cellulose triacetate fabric as 2% shade, showed fairly good to very good light fastness and very good to excellent fastness to washing, perspiration, rubbing and sublimation. All the dyes gave a wide range of reddish brown to indigo shades with very good depth and levelness on fabric. The purity of dyes was checked by thin layer chromatography. The percentage dyebath exhaustion and fixation on fabric was reasonably good and acceptable.     

Layer-by-layer assembled composite films of side-functionalized poly(3-hexylthiophene) and CdSe nanocrystals: electrochemical, spectroelectrochemical and photovoltaic properties

Regioregular poly(3-hexylthiophene) containing one diaminopyrimidine side group per ten repeat units (P3HT-co-P3(ODAP)HT) can form molecular composites with 1-(6-mercaptohexyl)thymine capped CdSe nanocrystals (CdSe(MHT)) via hydrogen bonds directed molecular recognition. Here we report complementary spectroscopic, electrochemical and spectroelectrochemical investigations of both the functionalized poly(thiophene) and its composite with the nanocrystals, the latter being fabricated using the layer-by-layer (LbL) deposition technique. UV-Vis-NIR and Raman spectroelectrochemical investigations unequivocally show that the onset of the first anodic peak in the cyclic voltammogram of the copolymer can be attributed to the oxidation of the pi-conjugated backbone in the polymer chains. For this reason, it is possible to determine the width and the position of its band gap (corresponding to the pi-pi* transition) by UV-Vis spectroscopy combined with cyclic voltammetry. These studies show that the polymer exhibits a slightly larger band gap with the HOMO level insignificantly lower in energy (by 0.03 eV) as compared to the case of regioregular poly(3-hexylthiophene) of comparable degree of polymerization. Hydrogen bond interactions of the polymer with CdSe(MHT) in the molecular composite result in a hypsochromic shift of the band corresponding to the pi-pi* transition from 504 nm to 488 nm. This can be taken as a spectroscopic manifestation of the conformational changes induced by shortening of the conjugation length. The observed spectral modifications are consistent with electrochemically determined lowering of the polymer HOMO level (from -4.91 eV in the pure polymer to -4.99 eV in the composite). Cyclic voltammetry studies supported by spectroelectrochemistry also show that the redox stability of CdSe(MHT) in the molecular composite with P3HT-co-P3(ODAP)HT is lower than that determined for stearate-capped nanocrystals. Their irreversible oxidation starts at E = +0.7 V vs. Ag/0.1 M Ag(+)i.e. at potentials by ca. 0.3 V lower than the oxidation of stearate stabilized CdSe nanocrystals of the same size. We show that-despite these modifications-the alignment of the HOMO and LUMO levels of the composite components remains appropriate for its use in hybrid solar cells, which is demonstrated by the photovoltaic effect observed for the LbL-processed composite sandwiched between two electrodes.     

Effect of chitosan and ions on actuation behavior of cellulose–chitosan laminated films as electro-active paper actuators

Cellulose-chitosan laminated films were made for Electro-Active Paper (EAPap) actuators and the effect of chitosan and different types of free ions namely, Cl⁻, NO₃⁻ and CF₃COO⁻ were investigated on the actuation behavior. The fabrication process of the films was explained and the actuation performance was tested in terms of bending displacement of the actuators. It was observed that, chitosan content and type of free ions influence the tip displacement of the actuators. Cl⁻ was found the best free ion among others, and detail observations are explained. By laminating chitosan layer on the cellulose films, the humidity sensitiveness of cellulose EAPap actuators was reduced.     

Electric-field-induced patterns in thin polymer films: weakly nonlinear and fully nonlinear evolution

A thin polymer melt on a substrate can be unstable to an electric field normal to the interface, a phenomenon that can be harnessed as a patterning technique with a range of potential applications. Motivated by the variety of patterns observed in experiments for polymers under both unpatterned and patterned masks, we describe here, from theoretical and numerical analyses, how nonlinear effects govern the growth of the instability and determine the final patterns. In particular, we discuss the nonlinear growth in terms of interactions among different Fourier modes and show that the second- and third-order nonlinearities favor the growth of hexagonal patterns under a featureless mask, in agreement with experimental observations. Also, numerical simulations based on the fully nonlinear model validate the prediction of the weakly nonlinear analysis: hexagonal patterns do emerge under an unpatterned mask. Furthermore, in one-dimensional simulations, we demonstrate the energetic evolution of this patterning process and reveal several "kinetically stable structures" along the path to the thermodynamically stable state. Two-dimensional simulations allow us to study the effects of both mask patterns and the initial film thickness. Generally, patterns on the mask guide the growth such that the pattern conforms to the geometric shapes. Interestingly, a small cylindrical protrusion at the center of the mask can produce exactly the same pattern as a large, flat, circular protrusion. The initial film thickness or the thickness ratio of the polymer layer to the air gap plays an important role in determining the final pattern formed. Finally, we demonstrate, by two simple examples, that the simulations can provide insights on "smart" mask designs for producing large areas of well-ordered patterns.     

Sustainable nanocomposite films based on bacterial cellulose and pullulan

Bionanocomposites with improved properties based on two microbial polysaccharides, pullulan and bacterial cellulose, were prepared and characterized. The novel materials were obtained through a simple green approach by casting water-based suspensions of pullulan and bacterial cellulose and characterized by TGA, RDX, tensile assays, SEM and AFM. The effect of the addition of glycerol, as a plasticizer, on the properties of the materials was also evaluated. All bionanocomposites showed considerable improvement in thermal stability and mechanical properties, compared to the unfilled pullulan films, evidenced by the significant increase in the degradation temperature (up to 40 °C) and on both Young’s modulus and tensile strength (increments of up to 100 and 50%, for films without glycerol and up to 8,000 and 7,000% for those plasticized with glycerol). Moreover, these bionanocomposite films are highly translucent and could be labelled as sustainable materials since they were prepared entirely from renewable resources and could find applications in areas as organic electronics, dry food packaging and in the biomedical field.     

Neutron reflectivity study of lipid membranes assembled on ordered nanocomposite and nanoporous silica thin films

Single bilayer membranes of 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine (POPC) were formed on ordered nanocomposite and nanoporous silica thin films by fusion of small unilamellar vesicles. The structure of these membranes was investigated using neutron reflectivity. The underlying thin films were formed by evaporation induced self-assembly to obtain periodic arrangements of silica and surfactant molecules in the nanocomposite thin films, followed by photocalcination to oxidatively remove the organics and render the films nanoporous. We show that this platform affords homogeneous and continuous bilayer membranes that have promising applications as model membranes and sensors.     

Characterization of self‐assembled phenyl and benzyl isothiocyanate thin films on Au surfaces

Structures of self‐assembled monolayers (SAMs) prepared from benzyl isothiocyanate (BZIT) and phenyl isothiocyanate (PHIT) were comparatively investigated by means of surface enhanced Raman scattering (SERS) on gold nanoparticle surfaces. Both the molecules are assumed to have upright geometries binding via the sulfur atom, from the SERS spectral features. The broad and split bands at ～2100 cm^?1 could be ascribed to the combination band ν_9a + ν₁₂ of the phenyl ring vibrations through a Fermi‐resonance interaction with the ν₃(NCS) band in the neat‐liquid state. Such broad bands became quite symmetric upon adsorption on Au. UV‐vis absorbance spectroscopy and cyclic voltammetry (CV) were used to compare the kinetics of the formation of SAMs on gold. Our results suggest that BZIT should have a relatively faster self‐assembly than PHIT, as indicated from signal decrease in the CV graph, which suggests a more vertical stance for BZIT in line with Raman measurements. Copyright © 2006 John Wiley & Sons, Ltd.     

Fast-response piezoresistive pressure sensor based on polyaniline cotton fabric for human motion monitoring

Wearable flexible sensors with quick response time and high stability are required in the fields of human motion detection, personal health monitoring, and artificial electronic skin. However, their design remains a challenge. To address this need, we fabricate a piezoresistive sensor with a wide detection limit, fast response time, and excellent stability in this work. Nickel (Ni) and copper (Cu) films are deposited on cotton fabric (CF) by in-situ polymerization of polyaniline (PANI) using magnetic filtration cathode vacuum arc deposition technology to obtain copper/polyaniline cotton (Cu/PANI/CF) and nickel/polyaniline cotton (Ni/PANI/CF). The pressure sensor is then fabricated by self-assembly. The proposed pressure sensor has a wide detection limit (0–180 kPa), rapid response time (30 ms), high cycle stability (>5000), and can detect the movement of each joint of the human body (such as the knee, finger, elbow, etc.). The sensor can also monitor different facial micro-expressions, including smiles and blinking. Based on the practical application of human motion signals and the detection of subtle stress, the proposed sensor demonstrates significant potential as a wearable electronic product for health monitoring.

Graphical abstract

     

Walljet electrochemistry: quantifying molecular transport through metallopolymeric and zirconium phosphonate assembled porphyrin square thin films

By employing redox-active probes, condensed-phase molecular transport through nanoporous thin films can often be measured electrochemically. Certain kinds of electrode materials (e.g. conductive glass) are difficult to fabricate as rotatable disks or as ultramicroelectrodes-the configurations most often used for electrochemical permeation measurements. These limitations point to the need for a more materials-general measurement method. Herein, we report the application of walljet electrochemistry to the study of molecular transport through model metallopolymeric films on indium tin oxide electrodes. A quantitative expression is presented that describes the transport-limited current at the walljet electrode in terms of mass transport through solution and permeation through the film phase. A comparison of the film permeabilities for a series of redox probes measured using the walljet electrode and a rotating disk electrode establishes the accuracy of the walljet method, while also demonstrating similar precision for the two methods. We apply this technique to a system consisting of zirconium phosphonate assembled films of a porphyrinic molecular square. Transport through films comprising three or more layers is free from significant contributions from pinhole defects. Surprisingly, transport through films of this kind is 2-3 orders of magnitude slower than through films constructed via interfacial polymerization of nearly identical supramolecular square building blocks (Keefe; et al. Adv. Mater. 2003, 15, 1936). The zirconium phosphate assembled films show good size exclusion behavior. The details of the observed dependence of permeation rates on probe molecule size can be rationalized with a model that assumes that the walls of the squares are slightly tilted from a strictly vertical geometry, consistent with atomic force microscopy measurements, and assumes that the individual wall geometries are locked by rigid interlayer linkages.     

Preparation of new cefazolin-containing films based on chitosan and carboxyarabinogalactan

Preparation of a polyelectrolyte complex of chitosan with the oxidized form of Siberian larch arabinogalactan at the component ratio from 0.05: 1 to 1: 1 was studied by spectrometry and laser scattering. Water-insoluble films based on this complex were prepared. These films were used as a matrix for drug immobilization. The possibility of controlling the rate and degree of the drug release from the film by variation of the polysaccharide ratio, modification of the polymer film with a sodium dodecyl sulfate solution, or heat treatment was demonstrated with cefazolin antibiotic as example. The films obtained exhibit high bactericidal activity.     

Antibacterial membranes based on chitosan and quaternary ammonium salts modified nanocrystalline cellulose

Etherification of nanocrystalline cellulose (NCC) with three kinds of quaternary ammonium salts epoxypropyltrimethylammonium chloride, N,N‐dimethyl‐N‐dodecyl‐N‐(1,2‐epoxypropyl) ammonium chloride (DMDEPAC), and N,N‐dimethyl‐N‐octadecyl‐N‐(1,2‐epoxypropyl) ammonium chloride (DMOEPAC) was successfully performed via a nucleophilic addition reaction. The synthesized DMDEPAC and DMOEPAC were characterized by nuclear magnetic resonance. The modified NCC particles, NCC epoxypropyltrimethylammonium chloride, NCC‐DMDEPAC, and NCC‐DMOEPAC, were characterized by energy dispersive spectrometer. Nanocomposite films based on chitosan (CS) containing quaternary ammonium salts modified NCC were prepared with nanoparticle loadings of 5.0, 7.5, and 10.0%, respectively. The effect of nanoparticle content on the tensile strength of composite films was studied. The results indicated that the films with 5.0% nanoparticle loading exhibited the biggest increase in tensile strength. Surface morphology, smoothness, and antibacterial properties of composite films containing 5% modified NCC were also studied. CS/NCC‐DMDEPAC‐5.0 and CS/NCC‐DMOEPAC‐5.0 displayed excellent biocidal abilities against both Gram‐positive Staphylococcus aureus (ATCC 6538) and Gram‐negative Escherichia coli O157:H7 (ATCC 43895). The bio‐based nanocomposite films with increased mechanical strength and excellent antibacterial properties show great potential as food packaging materials. Copyright © 2017 John Wiley & Sons, Ltd.