Multifunctional superhydrophobic/oleophobic and flame-retardant cellulose fibres with improved ice-releasing properties and passive antibacterial activity prepared via the sol–gel method

In this research, a two-component sol–gel inorganic–organic hybrid coating was prepared on a cotton fibre surface. An equimolar sol mixture of the precursors 1H,1H,2H,2H-perfluorooctyltriethoxysilane (SiF) and P,P-diphenyl-N-(3-(trimethoxysilyl)propyl) phosphinic amide (SiP) was applied to cotton fabric samples using the pad-dry-cure method. The surfaces of the untreated and coated cotton fibres were characterised using scanning electron microscopy, Fourier transform-infrared spectroscopy, X-ray photoelectron spectroscopy, and time-of-flight-secondary ion mass spectrometry. The functional properties of the coated cotton fabric samples were investigated using static contact angle measurements with water and n-hexadecane, the ice-releasing test, antibacterial testing against Gram-positive Staphylococcus aureus and Gram-negative Escherichia coli, thermogravimetric analysis in an air atmosphere, and vertical flammability tests. The results reveal the formation of a nanocomposite two-component inorganic–organic hybrid polymer network that is homogenously distributed over the cotton fibre surface. The presence of the SiP component in the two-component inorganic–organic hybrid coating did not hinder the functional properties imparted by the presence of the SiF component and vice versa, illustrating their compatibility. The cooperative action of the SiF and SiP components in the two-component coating provided the cotton fabric with exceptional multifunctionality, including simultaneous superhydrophobicity and high oleophobicity, passive antibacterial activity, and improved thermo-oxidative stability.     

Titanium dioxide fibers prepared by sol–gel process and centrifugal spinning

A new study of the preparation of nanocrystalline titanium dioxide (TiO₂) fibers is reported in the paper, which were prepared by sol–gel process with titanium acetate [Ti(CH₃COO)₄] as precursor. After that, centrifugal spinning and steam atmosphere heat-treatment were used to obtain final fibers. Here, the molecule structure of precursor was analyzed and the TiO₂ fibers obtained were characterized. Additionally, the effects of the silica (SiO₂) doping were discussed in this paper. By the Fourier transformation infrared spectrum analysis, the chain structure of –O–Ti–O–Ti–O– was confirmed in the Ti(CH₃COO)₄ precursor, as a result the precursor spinning solution showed a good spinning performance. And the pyrolysis process of precursor fibers was analyzed with the help of DSC–TG method. The phase of TiO₂ fibers obtained after heat-treatment with steam atmosphere was characterized mainly by the X-ray diffractometer (XRD), from the XRD curves, the result that the SiO₂ doping can efficiently inhibit the grain growth of TiO₂ fibers could also be verified. The microstructure of the TiO₂ fibers was observed by scanning electron microscope, which showed that diameter of TiO₂ fibers obtained with excellent continuity are from 5 to 10 μm. At last, the photocatalytic property of TiO₂ fibers was also tested.     

Preparation and characterization of nanocrystalline Ca-doped CeO2 by sol–gel process

The reactivity of CeO₂ is determined by grain size and oxygen vacancies, which can be achieved by doping elements with less oxidation state into CeO₂. In this study nanocrystalline Ca-doped CeO₂ sol was synthesized from the reaction of hydrate cerium (III) nitrate and calcium nitrate tetrahydrate in alcohol solution after being calcined at 600?°C. X-ray diffraction as well as selected area electron diffraction gave evidence that the synthesized Ca-doped CeO₂ samples were well crystalline and had a cubic fluorite structure. TEM observation revealed that Ca-doped CeO₂ was composed by nanoparticles with grain size around 8?nm. The Raman spectrum of pure CeO₂ consists of a single triple degenerate F_2g model characteristic of the fluorite-like structure. In the Ca-doped CeO₂ sample, two additional low-intensity Raman bands were detected, thus confirming the formation of the solid solution. The synthesized nanometric powder is expected to be used in solid oxide fuel cells as well as in the catalytic treatment of automobile exhaust fumes.     

Sol–gel coating of cellulose fibres with antimicrobial and repellent properties

Multifunctional, water and oil repellent and antimicrobial finishes for cotton fibres were prepared from a commercially available fluoroalkylfunctional water-born siloxane (FAS) (Degussa), nanosized silver (Ag) (CHT) and a reactive organic–inorganic binder (RB) (CHT). Two different application procedures were used: firstly, one stage treatment of cotton fabric samples by FAS sol (i), as well as by a sol mixture constituted from all three precursors (Ag–RB–FAS, procedure 1S) (ii), and secondly, two stage treatment of cotton by Ag–RB sol and than by FAS sol (Ag–RB + FAS, procedure 2S) (iii). The hydrophobic and oleophobic properties of cotton fabrics treated by procedures (i)–(iii) before and after consecutive (up to 10) washings were established from contact angle measurements (water, diiodomethane and n-hexadecane) and correlated with infrared and XPS spectroscopic measurements. The results revealed that even after 10 washing cycles cotton treated with Ag–RB + FAS (2S) retained an oleophobicity similar to that of the FAS treated cotton, while the Ag–RB–FAS (1S) cotton fibres exhibited a loss of oleophobicity already after the second washing, even though fluorine and C–F vibrational bands were detected in the corresponding XPS and IR spectra. The antibacterial activity of cotton treated by procedures (i)–(iii) was tested by its reduction of the bacteria Escherichia coli and Staphylococcus aureus following the AATCC 100-1999 standard method and EN ISO 20743:2007 transfer method. The reduction in growth of both bacteria was nearly complete for the unwashed Ag–RB and Ag–RB–FAS (S1), but for the unwashed Ag–RB + FAS (S2) treated cotton no reduction of S. aureus and 43.5 ± 6.9% reduction of E. coli was noted. After the first washing, the latter two finishes exhibited nearly a complete reduction of E. coli but for the Ag–RB treated cotton the reduction dropped to 88.9 ± 3.4. None of the finishes retained antibacterial properties after 10 repetitive washings. The beneficial and long-lasting low surface energy effect of FAS finishes in the absence of Ag nanoparticles, which led to the “passive” antibacterial properties of FAS treated cotton fabrics, was established by applying the EN ISO 20743:2007 transfer method. The results revealed a reduction in bacteria of about 21.9 ± 5.7% (FAS), 13.1 ± 4.8% (Ag–RB–FAS (S1)) and 41.5 ± 3.7% (Ag–Rb + FAS (S2)), while no reduction of the growth of bacteria was observed for cotton treated with Ag nanoparticles after 10 repetitive washings. The physical properties (bending rigidity, breaking strength, air permeability) of finished cotton samples were determined, and showed increased fabric softness and flexibility as compared to the Ag–RB treated cotton, but a slight decrease of breaking strength in the warp and weft directions, while air permeability decreased for all type of finishes.     

High water solubility and sol–gel transition behavior of titania nanoparticles obtained by an in situ functionalization sol–gel process

Herein, addition reaction occurred between glycidol and partially hydrolyzed Ti⁴⁺ complexes provides a opportunity to obtain dry anatase nanopowder with high redispersity in water. This property is considered to be originated from the two OH groups located in the two ends of glycidol resulted chlorinated propandiol molecules. In aqueous solution, the two OH groups are respectively connected with particle surface and external free water by the formation of hydrogen bonds, resulting in high water redispersity of nanoparticles. Due to the much less amount of chlorinated propandiol molecules than adsorbed molecule water on particle, the wide space between organic molecules facilitates the mutual physical surface touch of individual particles to form hydrogen bond between them. A novel property is then obtained for surface modified titania nanoparticles, which is the gelation of redispered nanoparticles in aqueous solution.     

Preparation and characterization of boron-based bioglass by sol−gel process

45S5 bioglass has been widely studied in the last few decades because of its bioactivity and promising applications in the biomedical field. Boron, even few studied, represents a potential element to improve the properties of the 45S5 bioglass derivatives. The bioglasses are conventionally prepared by heat treatment of oxides and silicon. Here, the sol?gel method is proposed for the preparation of the boron-based 45S5 bioglass (45S5B) and the classical 45S5 bioglass (45S5), using water-soluble salts as raw materials. The bioglasses were characterized by FTIR, XRD, and SEM, indicating the success of the sol?gel method for preparation of the samples. The bioglasses were also tested in vitro for bioactivity in biological conditions and cytotoxicity against eukaryotic cells. The bioactivity of 45S5B was similar to the bioactivity of 45S5 bioglass, indicated by the deposition of hydroxyapatite crystals at the surface of the pristine bioglasses. The results of cytotoxicity tests revealed that the IC₅₀ of 45S5B (IC₅₀?=?7.56?mg?mL^?1) was similar to the IC₅₀ of 45S5 (IC₅₀?=?8.15?mg?mL^?1), indicating its safety for application in the biomedical field.

Open image in new window

     

Co-doped ZnO nanoparticles synthesized by an adapted sol–gel method: effects on the structural,optical, photocatalytic and antibacterial properties

Pure and Co-doped ZnO nanoparticles were synthesized with different cobalt levels (1–10 mol%) via adapted sol–gel method using water as solvent and characterized by X-ray diffraction, transmission electron microscopy, Raman spectroscopy and photoacoustic absorption spectroscopy. The results showed that all the samples have hexagonal wurtzite structure, with no evidence of any secondary phases until 10 mol% of the dopant. The average crystallite size of the samples was in the range of 25–50 nm, do not showing significant differences with the increase of the dopant level. However, the band gap energy of the nanoparticles decreases from 2.98 eV (pure ZnO) to 1.95 eV (10 mol% of Co). The photocatalytic activity of the samples was evaluated on the removal of methylene blue under visible light irradiation, which revealed an efficiency reduction by Co-doping ZnO. The antibacterial property was carried out indicating activity of the prepared samples against gram-positive bacteria.     

How to design cell-based biosensors using the sol–gel process

Inorganic gels formed using the sol–gel process are promising hosts for the encapsulation of living organisms and the design of cell-based biosensors. However, the possibility to use the biological activity of entrapped cells as a biological signal requires a good understanding and careful control of the chemical and physical conditions in which the organisms are placed before, during, and after gel formation, and their impact on cell viability. Moreover, it is important to examine the possible transduction methods that are compatible with sol–gel encapsulated cells. Through an updated presentation of the current knowledge in this field and based on selected examples, this review shows how it has been possible to convert a chemical technology initially developed for the glass industry into a biotechnological tool, with current limitations and promising specificities.     

ZnO nanorods on ZnO seed layer derived by sol–gel process

Well-aligned ZnO nanorods are obtained by a liquid phase epitaxial growth on the indium-doped tin oxide glass deposited with a ZnO thin film as the seed layer, which is prepared by combining a sol–gel process and a spin coating technique. The effects of water content in the sol and heat treatment temperature on the properties of the ZnO thin film are investigated. Relationship among the seed layer, the growing time, the growing temperature, the concentration of Zn²⁺ in the solution, the anions in the solution and the resulting ZnO nanorods are discussed in detail. X-ray diffraction analysis and scanning electronic microscopy are employed to characterize the structural and morphological properties of the resulting ZnO nanorods. Results indicate that the ZnO nanorods with a preferred orientation show a single crystal with a wurtzite structure in the direction of [0001], the diameter of the ZnO nanorods seems to depend on the size of the seed grain, while the length of the ZnO nanorods is determined by the growing time and the growing temperature.     

Lactic acid based sol–gel process of Ag nanoparticles and crystalline phase control of Ni particles in aqueous sol–gel process

Nickel and silver particles were prepared by using sol–gel auto-combustion method under N₂ atmosphere where lactic acid was applied as chelating agent. The synthesis of nickel particles was carried out at various pH conditions (2–7), resulting in the face-centered-cubic or hexagonal-close-packed crystalline nickel phase. The morphology and structure of synthesized nickel particles and silver nanoparticles were characterized by X-ray diffraction, transmission electron microscope, energy dispersive X-Ray spectroscopy and differential scanning calorimetry-thermogravimetric analysis. The results show that the spherical Ag nanoparticles with diameters in the range of 18–27 nm and narrow size distribution can be obtained by this sol–gel process.     

Preparation of superhydrophobic silica nanoparticles by microwave assisted sol–gel process

Hydrophobic silica nanoparticles were obtained by microwave assisted sol–gel method using a two-step procedure. In the first step different size silica particles were generated from tetraethyl orthosilicate and in the second one the silica particles were hydrophobized using hexadecyl trimethoxysilane (HDTMOS). Under microwave irradiation, high conversion degrees were obtained at relatively short reaction times. The HDTMOS added in the second step instead of coating the silica nanoparticles generated new ones and therefore the final product showed a bimodal size distribution. All the synthesized nanoparticles gave rise to high water contact angles (≈150°) and low hysteresis values.     

Preparation and properties of VO2 thin films by a novel sol–gel process

Vanadium dioxide (VO₂) thin films were fabricated using a simple and novel sol–gel process in which V₂O₅ was used as the vanadium source; oxalic acid was used as the reducing agent; and polyvinyl alcohol was used as the film former to control the viscosity of the VO₂ precursor solution and bond vanadium ions. The microstructure and surface morphology of VO₂ films were studied by X-ray diffraction and scanning electron microscopy, respectively. The results showed that using polyvinyl alcohol forms porous nanostructure of VO₂ films with a uniform grain size of ~25 nm. The measured optical reflectance shows well-defined phase transition as observed by an increase of reflectance upon heating above the transition temperature from ~11 to ~30 % at 1,100 nm. Upon cooling, the expected hysteresis is observed.     

Borate,lithium borate,and borophosphate powders by sol–gel precipitation

Borate, lithium borate and borophosphate powders were synthesized by the sol–gel method. Triethyl borate, lithium methoxide, and orthophosphoric acid were used as precursors for B₂O_3, Li₂O, and P₂O₅, respectively. Powders were characterized by FTIR, DTA, XRD and SEM techniques. Powders from the Li₂O–B₂O₃ system exhibited glassy features while borate and borophosphate powders contained mainly crystalline B₂O₃ according to XRD analysis. However, a 500 °C heat treatment transformed these crystalline powders into glass powders. Conversely, heat treatment of Li₂O–B₂O₃ powders transformed their structure from glassy to crystalline (Li₂B₄O₇). Chemical durability studies conducted in water at 60 °C showed that minor additions of P₂O₅ into borate and lithium borate powders improved their chemical durability significantly. Furthermore, Li₂O and P₂O₅ acted synergistically on the chemical durability when added simultaneously to borate compositions.     

Comparative study of the thermal behavior of Sr–Cu–O gels obtained by sol–gel and microwave-assisted sol–gel method

Journal of Thermal Analysis and Calorimetry - In the literature data, several papers reported the synthesis by various chemical or physical methods of the SrCu2O2 (SCO) having possible applications...