A novel concept for in situ gas-phase laser Raman spectroscopy for solid oxide fuel cell research

A planar solid oxide fuel cell (SOFC) operated with hydrogen at T = 1,123 K was equipped with an optically transparent anode flow field to apply species concentration measurements by 1D laser Raman scattering. The flow channels had a cross section of 3 mm × 4 mm and a length of 40 mm. The beam from a pulsed high-power frequency-doubled Nd:YAG laser (λ = 532 nm) was directed through one channel and the Raman-scattered light from different molecular species was imaged onto an intensified CCD camera. The main goal of the study was an assessment of the potential of this experimental configuration for a quantitative determination of local gas concentrations. The paper describes the configuration of the optically accessible SOFC, the laser system and optical setup for 1D Raman spectroscopy as well as the challenges associated with the measurements. Important aspects like laser pulse shaping, signal background and signal quality are addressed. Examples of measured species concentration profiles are presented.     

Energy efficiency of drilling granite and travertine with a CO2 laser and 980 nm diode laser

Using lasers to drill hard rock presents potential advantages compared to conventional mechanical drilling, such as higher penetration rates and reduced vibration. Before realistic drilling tools can be proposed, the influence of important parameters and the mechanisms involved in drilling different rocks with different lasers must be understood. In this work, we investigate the efficiency of laser drilling of granite and travertine with a CO₂ laser and a 980 nm fiber coupled diode laser. At the drilling surface, the maximum CW power delivered by the CO₂ laser was 140 W, while the diode laser delivered up to 215 W. Even at these modest power levels, it was possible to drill holes with diameters of the order of 8 mm at efficiencies varying from 40 kJ/cm³ to 150 kJ/cm³. The optimum laser exposure period of time was also investigated. Finally, x-ray diffraction and fluorescence analysis, as well as Tg (Thermogravimetry) and DTA (Differential Thermal Analysis) measurements, were performed on the rocks samples used.     

Passively Q-switched Tm,Ho:LuLiF4 laser with near constant pulse energy and duration

A compact diode-pumped passively Q-switched Tm,Ho:LuLiF₄ laser with a Cr:ZnS saturable absorber is demonstrated for the first time. The maximum average output power of 74 mW is achieved at the absorbed pump power of 1.5 W, and the threshold power is only 0.68 W. The laser operates at the wavelength of 2,055 nm and produces pulses with near constant duration of 1.2 μs and pulse energy of 13 μJ at the pulse repetition frequency from 1 to 5.2 kHz. The stable long-pulse laser can be used in laser lidar systems for accurate wind velocity measurements.     

Sensitive detection of acrolein and acrylonitrile with a pulsed quantum-cascade laser

We report on spectroscopic measurements of acrolein and acrylonitrile at atmospheric pressure using a pulsed distributed feedback quantum-cascade laser in combination with intra- and inter-pulse techniques and compare the results. The measurements were done in the frequency region around 957 cm^?1. In the inter-pulse technique, the laser is excited with short current pulses (5–10 ns), and the pulse amplitude is modulated with an external current ramp resulting in a ～2.3 cm^?1 frequency scan. In the intra-pulse technique, a linear frequency down-chirp during the pulse is used for sweeping across the absorption line. Long current pulses up to 500 ns were used for these measurements which resulted in a spectral window of ～2.2 cm^?1 during the down-chirp. These comparatively wide spectral windows facilitated the measurements of the relatively broad absorption lines (～1 cm^?1) of acrolein and acrylonitrile. The use of a room-temperature mercury-cadmium-telluride detector resulted in a completely cryogen-free spectrometer. We demonstrate ppb level detection limits within a data acquisition time of ～10 s with these methodologies.     

Optical properties of zinc phthalocyanine thin films prepared by pulsed laser deposition

ZnPc thin films were prepared by pulsed laser deposition (KrF laser, λ = 248 nm, τ = 5 ns, f = 50 Hz) on suprasil substrates in vacuum. Optical properties in UV–Vis spectral region were analyzed as functions of laser fluence from 40 to 100 mJ/cm² by spectrophotometric and spectral ellipsometry measurements. The spectral ellipsometry data were treated using a three-layer model (substrate, film, roughness). The best results of data fitting were obtained when Q band was characterized by two Lorentz oscillators, while two Gaussian oscillators were used for B and C band fitting. We derived the band gap using Tauc plot considering ZnPc a direct band gap semiconductor. The band gap values were found decreasing from 3.13 to 3.09 eV with increasing laser fluence, which might be related with formation of trapping sites at higher fluence.     

Radiation effects on poly(methyl methacrylate) induced by pulsed laser irradiations

Poly(methyl methacrylate) (PMMA) was irradiated using a medical UV-ArF excimer laser operating at the fundamental wavelength of 193 nm. Characterized by a beam diameter of 1.8 mm and energy of 180 mJ with a Gaussian energy profile, it operates in a single mode or at 30 Hz repetition rate. Mechanical profilometry was carried out on ablation craters in order to study the rugosity and the ablation yield in the various operative conditions. Optical transmission and reflection measurements at six wavelengths were conducted in order to characterize the optical properties of the irradiated surfaces. Measured crater depths in PMMA were lower with respect to the forecasted ones in corneal tissue, while the lateral crater aperture was maintained. The rugosity produced at the crater bottom after irradiation was about 0.3 μm, and the ablation yield was about 10¹⁵ molecules/laser pulse, while etching depth and diameter show a roughly linear dependence on the number of laser shots. These experiments constitute a base for deeper clinical investigations.     

Detection of propane using tunable diode laser spectroscopy at 3.37 μm

We report Tunable Diode Laser Spectroscopy measurements of propane using a recently developed 3.37 μm GaInAsSb/AlGaInAsSb DFB laser. We have demonstrated that Wavelength Modulation Spectroscopy can be utilized to enhance a sharp feature in the broader propane spectrum around 3370.4 nm. A minimum detectable concentration of 30 ppb×m was obtained at a response time of 0.5 s. This corresponded to a minimum detectable absorption of 8 × 10^?5 which is why an improvement of the sensitivity by an order of magnitude is possible using this laser and a more optimized optical setup.     

Solid-state laser system for laser cooling of sodium

We demonstrate a frequency-stabilized, all-solid laser source at 589 nm with up to 800 mW output power. The laser relies on sum-frequency generation from two laser sources at 1064 nm and 1319 nm through a PPKTP crystal in a doubly resonant cavity. We obtain conversion efficiencies as high as 2 W/W² after careful optimization of the cavity parameters. The output wavelength is tunable over 60 GHz, which is sufficient to lock on the sodium D₂ line. The robustness, beam quality, spectral narrowness and tunability of our source make it an alternative to dye lasers for atomic physics experiments with sodium atoms.     

Simultaneous CO concentration and temperature measurements using tunable diode laser absorption spectroscopy near 2.3 μm

Simultaneous measurements of carbon monoxide (CO) mole fraction and temperature using tunable diode laser absorption spectroscopy (TDLAS) near 2.3 μm are reported. The measurement method uses ro-vibrational transitions [R(27): v″ = 1 → v′ = 3] and [R(6): v″ = 0 → v′ = 2] in the first overtone band of CO near 2.3 μm (~4,278 cm^?1). The measurements were performed in the post flame environment of fuel rich premixed ethylene–air flames with a N₂ co-flow, stabilized over a water cooled McKenna burner. Non-uniformity in the temperature and CO mole fraction, along the absorption line of sight, in the mixing layer of the co-flow, was considered during data analysis. The TDLAS based temperature measurements (±80 K) were in good agreement with those obtained using N₂ vibrational coherent anti-Stokes Raman scattering (±20 K), and the CO mole fraction measurements were in good agreement with the equilibrium values, for equivalence ratios lower than 1.8. A signal to noise ratio of 45 was achieved at an equivalence ratio of 1 for a CO concentration of 0.8 % at 1,854 K.     

Laser-induced ablation and crater formation at high laser flux

Laser ablation and crater formation have been studied on a copper target using a 10 Hz Nd:YAG laser system delivering pulses up to 100 mJ in 40 ps with a flux on target F?≤?5000 J/cm². Crater dimensions were measured using optical microscope or scanning electron microscope. In order to understand the process of crater formation, we considered various theoretical models present in the literature and revised them taking into account the occurrence of plasma phenomena, which are important at the intensities used in this experiment. We also compared our experimental results with other results obtained at the PALS laboratory, using a 0.44 μm wavelength laser and much higher laser intensities. Finally, we explore the possibility of extending the information derived from laser-produced craters to other types of craters.     

Using a DS-DBR laser for widely tunable near-infrared cavity ring-down spectroscopy

Studies into the suitability of a novel, widely tunable telecom L-band (1,563–1,613 nm) digital supermode distributed Bragg reflector (DS-DBR) laser for cavity ring-down spectroscopy (CRDS) are presented. The spectrometer comprised of a 36.6?cm long linear cavity with ring-down times varying between 19–26 μs across the 50 nm DS-DBR wavelength range due to changes in the cavity mirror reflectivities with wavelength. The potential of such a broadband, high-resolution CRD spectrometer was illustrated by investigating several transitions of CO₂ in air, a 5 % calibrated mixture and breath samples. Allan variance measurements at a single wavelength indicated an optimal minimum detectable absorption coefficient (α _min) of 3 × 10^?10 cm^?1 over 20 s.     

Single-frequency polarized eye-safe all-fiber laser with peak power over kilowatt

An all-fiber, single-frequency, linearly polarized, high peak-power, pulsed laser at 1,540 nm for Doppler wind lidar is presented. This laser is composed of a single-frequency, narrow-linewidth external cavity diode laser, and multistage fiber amplifiers. A peak power of 1.08 kW and a pulse width of 500 ns at 10 kHz repetition rate are achieved, which is the highest peak power with a linewidth of 800 kHz in erbium-doped silica fiber to our knowledge. The beam quality of M ² < 1.3 and a polarization extinction ratio over 16 dB are obtained. This laser will be employed in a compact long-range coherent Doppler wind lidar.     

Characterization of the 46.9-nm soft X-ray laser beam from a capillary discharge

Intense lasing had been obtained from argon plasma in the soft X-ray region from a capillary discharge plasma system. Different diagnostics have been used to characterize the lasing properties by recording the temporal, spatial, and spectral profiles of the emission. The divergence measurement indicates that the soft X-ray laser beam has good directionality with a divergence of 3.5 mrad. The spectrum of the laser beam measured using a transmission grating showed intense lasing line at 46.9 nm. Diffraction orders as high as 10th orders were observed. The temporal profile recorded with a vacuum diode showed a distinct laser peak with a pulse width ~1.2 ns (FWHM). In addition, the coherence of the X-ray laser beam was also confirmed from the high-contrast interference fringes (visibility ~85 %) recorded using double slits.     

Sub-Doppler spectroscopy with an external cavity quantum cascade laser

The linewidth of an external cavity quantum cascade laser is studied as a function of injection current and laser scan rate. The laser linewidth is inferred to be ca. 2.5 MHz from Lamb-dip spectra on a low pressure sample of NO and its variation with injection current is well modeled using literature values for the intrinsic material properties of the lasing medium. The laser linewidth measurements are corroborated by polarization spectroscopy studies as well as by analysis of hyperfine structure and cross-over resonances.     

Detection of buried layers in silicon devices using LIBS during hole drilling with femtosecond laser pulses

Femtosecond laser micromachining together with Laser Induced Breakdown Spectroscopy (LIBS) allows us to drill precise hole in materials to internal buried layers as well as characterize the materials while drilling. We report detection of a metal layer buried deep inside silicon by creating an access hole through the semiconductor. We used 800 nm femtosecond laser pulses to carry out the drilling while monitoring the plasma emission with a spectrometer system. Higher drilling rates of 1 μm per shot were achieved using a Gaussian laser beam profile with peak fluences of 42 J/cm². Lower drilling rates of 30 nm per pulse with better accuracy could be achieved using lower intensity flat top beam profiles at fluences of 1.4 J/cm².     

Characterization of laser-induced ultrasound signal by reduced graphene oxide thickness and laser intensity

A nanosecond pulse laser generates acoustic waves on a water-material interface. The absorbed beam energy heats and thermoelastically expands the material. The thermoelastic stress of a material is dependent on its absorbance and expansion coefficient. In this work, we used a composite of reduced graphene oxide (RGO) and aluminum thin film to increase the efficiency of conversion from beamed energy to thermoelastic stress. A laser shadowgraph showed enhanced acoustic waves propagating at ~1,500 m/s under water. The effect of RGO on ultrasound generation is examined for different thicknesses of RGO at several laser fluences. The pressure of laser-induced ultrasound on the RGO–aluminum composite was measured to be up to 59 times greater than that produced with an aluminum film alone, and the frequency of laser-induced ultrasound was determined by the thermoelastic response. The strong intensity and broad bandwidth of the laser-induced acoustic wave suggested enhanced repetition time and resolution required for biomedical imaging.     

All-solid-state continuous-wave laser systems for ionization,cooling and quantum state manipulation of beryllium ions

We describe laser systems for photoionization, Doppler cooling, and quantum state manipulation of beryllium ions. For photoionization of neutral beryllium, we have developed a continuous-wave 235 nm source obtained by two stages of frequency doubling from a diode laser at 940 nm. The system delivers up to 400 mW at 470 nm and 28 mW at 235 nm. For control of the beryllium ion, three laser wavelengths at 313 nm are produced by sum-frequency generation and second-harmonic generation from four infrared fiber lasers. Up to 7.2 W at 626 nm and 1.9 W at 313 nm are obtained using two pump beams at 1051 and 1551 nm. Intensity drifts of around 0.5 % per hour have been measured over 8 h at a 313 nm power of 1 W. These systems have been used to load beryllium ions into a segmented ion trap.     

Eye-safe Raman laser based on BaTeMo2O9 crystal

An eye-safe Raman laser is realized with BaTeMo₂O₉ (BTM) nonlinear crystal for the first time. By using a diode-end-pumped acousto-optically Q-switched Nd:YVO₄ laser as the pumping source, the BTM crystal converts the fundamental laser at 1,342 nm to first-Stokes laser at 1,531 nm successfully. With an incident power of 10.8 W and a pulse repetition rate of 25 kHz, the average output power at 1,531 nm is obtained to be 0.83 W, corresponding to a diode-to-Stokes conversion efficiency of 7.7 %. The pulse width is 11 ns, and the peak power is 3.0 kW.     

DCOOD optically pumped by a 13CO2 laser: new terahertz laser lines

In this work we report on new optically pumped THz laser lines from deuterated formic acid (DCOOD). An isotopic ¹³CO₂ laser was used for the first time as a pump source for this molecule, and a Fabry–Perot cavity was used as a THz laser resonator. Optoacoustic absorption spectra were used as a guide to search for new THz laser lines. We could observe six new laser lines in the range from 303.8 μm (0.987 THz) to 725.1 μm (0.413 THz). The lines were characterized according to wavelength, relative polarization, relative intensity, and optimum working pressure. The transferred lamb-dip technique was used to measure the frequency absorption transition for both of these laser lines. Furthermore, we also present a catalogue of all THz laser lines generated from DCOOD.     

Double-line terawatt OPCPA laser system for exciting beat wave oscillations

A double-line terawatt beat laser (BEAT) is developed for exciting beat wave oscillations. BEAT consists of two oscillators and an amplification system including optical parametric chirped-pulse amplification (OPCPA) in which two individual pulses with wavelength separations of 10–35 nm are amplified, recompressed, and focused as a single beam. The recompressed pulse trace shows that a 150-fs pulse duration full width at half maximum was modulated at a beating period of 72 fs. This beating period matches a resonant excitation of plasma wave with an electron density of 2.5 × 10¹⁸ cm^?3, resulting in excitation of a beat wave in hydrogen plasma with wave amplitude of 15 GV/m. The multiple beating oscillations can amplify the plasma wave and improve its structure. This scheme would be ideal for stabilizing the plasma wave strength in the plasma cavity and for realizing a practical laser plasma accelerator.