The effect of gamma irradiation on mechanical, and thermal properties of recycling polyethylene terephthalate and low density polyethylene (R-PET/LDPE) blend compatibilized by ethylene vinyl acetate (EVA)

A study has been made on the compatibility of recycled polyethylene terephthalate (R-PET) and low density polyethylene (LDPE) blend in the presence of ethylene vinyl acetate (EVA) as a compatibilizing agent prepared by extrusion hot stretching process. EVA content in the blend as a compatibilizing agent was an enhancement effect on radiation crosslinking of R-PET/EVA/LDPE blends and the highest radiation crosslinking was obtained when the EVA content was reached at 10 % EVA when irradiated by gamma irradiation. Blends containing different (EVA) ratios were irradiated to different doses of gamma irradiation 25, 50 and 100 kGy. The effect of the compatibilizer and radiation on mechanical, thermal properties of R-PET together with LDPE and morphology has been investigated. It was found that gamma irradiation together with the presence of compatibilizing agent (EVA) has positive effect on the mechanical and thermal properties of R-PET/LDPE blend. The structural properties of R-PET/LDPE modified by gamma irradiation and EVA as compatibilizing agent was examined by SEM. Also, it was found that the optimum concentration of EVA and gamma irradiation dose was found to be 10 % EVA and 100 kGy, respectively.     

Shape memory behavior of carbon nanotube‐reinforced trans‐1,4‐polyisoprene and low‐density polyethylene composites

Shape memory composites of trans‐1,4‐polyisoprene (TPI) and low‐density polyethylene (LDPE) with easily achievable transition temperatures were prepared by a simple physical blending method. Carbon nanotubes (CNTs) were introduced to improve the mechanical properties of the TPI/LDPE composites. The mechanical, cure, thermal, and shape memory properties of the TPI/LDPE/CNTs composites were investigated in this study. In these composites, the cross‐linked network generated in both the TPI and LDPE portions acted as a fixed domain, while the crystalline regions of the TPI and LDPE portions acted as a domain of reversible shape memory behavior. We found that CNTs acted as not only reinforced fillers but also nucleation agents, which improved the crystalline degree of the TPI and LDPE portions of the composites. Compared with the properties at the other CNT doses, the mechanical properties of the TPI/LDPE composites when the CNT dose was 1 phr were improved significantly, showing excellent shape memory properties (R_f = 97.85%, R_r = 95.70%).     

Study of thermal and dielectric behavior of low-density polyethylene composites reinforced with zinc oxide whisker

Different scanning calorimetry and dynamic mechanical analysis are used to study the thermal behavior of composites by melt-mixing low-density polyethylene (LDPE) matrix and zinc oxide whisker (ZnO_w) fillers. Micrographs of the composites illustrate that needle or wedge shaped ZnO_w are distributed uniformly in the LDPE matrix. Dielectric properties of the composites are measured in a frequency range of 1-10 MHZ. The results show that the addition of ZnO_w does not affect the melting behavior of LDPE, but has an important effect on the heat of fusion, dynamic mechanical behavior, and dielectric behavior of the composites. This revised version was published online in July 2006 with corrections to the Cover Date.     

Melt elongation flow behaviour of LDPE/LLDPE blends

The extensional rheological properties of low density polyethylene (LDPE)/linear low density polyethylene (LLDPE) blend melts were measured using a melt spinning technique under temperatures ranging from 160 to 200 °C and die extrusion velocities varying from 9 to 36 mm/s. The results showed that the melt elongation stress decreased with a rise of temperature while it increased with increasing extensional strain rate and the LDPE weight fraction. The dependence of the melt elongation viscosity on temperature roughly obeyed the Arrhenius equation, it increased with increasing extensional strain rate and the LDPE weight fraction when the extensional strain rate was lower than 0.5 s⁻¹, and it reached a maximum when the extensional strain rate was about 0.5 s⁻¹, which can be attributed to the stress hardening effect.     

Effect of crosslinking on the properties of composites based on LDPE and conducting organic filler

New types of composites were prepared using low-density polyethylene (LDPE) filled with modified organic filler, Canadian switch grass coated with polypyrrole (PPy). The grass surface was entirely covered when 10 wt.% of pyrrole was used for the modification, as confirmed by scanning electron microscopy and infrared spectroscopy. LDPE composites filled with modified grass were prepared by melt mixing and their properties were compared with the properties of the composites filled with unmodified grass. The influence of crosslinking, induced by 1 wt.% of peroxide, on mechanical, thermal and electrical properties of the composites was investigated. Crosslinking enhanced the tensile strength of the prepared composites in the entire range of the filler content. The Young’s modulus of the composites prepared by crosslinking is slightly lowered when compared with the uncrosslinked composites if the filler content is less than 60 wt.%, for higher filler content it is increased. The conductivity of the uncrosslinked composites containing 40 wt.% of grass modified by PPy was in the range 1 × 10⁻⁶ S cm⁻¹, which is a value by 5 orders of magnitude higher than the conductivity of the crosslinked materials. The presence of PPy on grass surface leads to a reduction of crosslinking of the LDPE matrix.     

Thermal stability of styrene butadiene rubber (SBR) composites filled with kaolinite/silica hybrid filler

Styrene butadiene rubber (SBR) composites filled with fillers, such as modified kaolinite (MK), precipitated silica (PS), and the hybrid fillers containing MK and PS, were prepared by melt blending. The kaolinite sheets were finely dispersed in the SBR matrix around 20–80 nm in thickness and reached the nano-scale. The SBR composites with fillers exhibited excellent thermal stability compared to the pure SBR. The thermal stability of SBR composites was improved with the increasing of MK mass fraction. When MK hybridized with PS, kaolinite sheets were covered by the fine silica particles and the interface between filler particles and rubber matrix became more indistinct. SBR composite filled by hybrid fillers containing 40 phr MK and 10 phr PS became more difficult in decomposition and was better than that of 50 phr PS/SBR and 50 phr MK/SBR in thermal stability. Therefore, the hybridization of the fine silica particles with the kaolinite particles can effectively improve the thermal stability of SBR composites.     

Dispersion evaluation of microcrystalline cellulose/cellulose nanofibril-filled polypropylene composites using thermogravimetric analysis

Microcrystalline cellulose-filled polypropylene (PP) composites and cellulose nanofiber-filled composites were prepared by melt blending. The compounded material was used to evaluate dispersion of cellulose fillers in the polypropylene matrix. Thermogravimetric analysis (TG) and mechanical testing were conducted on composites blended multiple times and the results were compared with single batch melt blended composites. The residual mass, tensile strength, and coefficient of variance values were used to evaluate dispersion of the microcrystalline cellulose fillers in the PP matrix. The potential of using TG to evaluate cellulose nanofiber-filled thermoplastic polymers was also investigated and it was found that the value and variability of residual mass after TG measurements can be a criterion for describing filler dispersion. A probabilistic approach is presented to evaluate the residual mass and tensile strength distribution, and the correlation between those two properties. Both the multiple melt blending and single batch composites manufactured with increased blending times showed improved filler dispersion in terms of variation and reliability of mechanical properties. The relationship between cellulose nanofiber loading and residual mass was in good agreement with the rule of mixtures. In this article, the authors propose to use a novel method for dispersion evaluation of natural fillers in a polymer matrix using TG residual mass analysis. This method can be used along with other techniques such as scanning electron microscope (SEM), transmission electron microscope (TEM), and X-ray diffraction (XRD) for filler dispersion evaluation in thermoplastic composites.     

Effect of carbon nanotube modification on poly(butylene terephthalate)-based composites

The influence of the chemical modification of carbon nanotubes on the mechanical, thermal and electrical properties of poly(butylene terephthalate)-based composites was investigated. Polymer composites based on poly(butylene terephthalate) were obtained via in situ polymerisation or extrusion. Commercially available multi-walled carbon nanotubes (Nanocyl NC7000) at different loadings (mass %: 0.05, 0.25, 1, 2) were used as fillers. The functionalisation process took place under a chlorine atmosphere followed by a reaction with sodium hydroxide. The effect of carbon nanotube modification was analysed according to the changes in the polymer thermal and mechanical properties. An addition of modified carbon nanotubes in the amount of 0.05 mass % improved the mechanical properties of the composites in terms of both Young’s modulus and tensile strength by 5–10 % and 17–30 % compared with composites with unmodified carbon nanotubes and neat poly(butylene terephthalate), respectively. The in situ method of composite preparation was a more effective technique for enhancing the matrix-filler interactions, although a significantly lower amount of fillers were used than in the extrusion method.     

Mechanical,thermal, and morphological properties of powder coating waste reinforced acetal copolymer

The present study investigates the individual effects of three different thermosetting waste materials, used as fillers, on the mechanical, thermal and flow properties of acetal copolymers (POM). Different amounts ranging from 5% to 30% by weight of hydrolyzed powder coating recyclates were mixed as filler material in POM. The matrix and the fillers were first dry-mixed and then compounds were prepared through melt extrusion. The resulting compounds were cooled, granulated, and then standard tensile test bars were produced through use of an injection-molding machine. We investigated the mechanical and thermal properties of test specimens, and tensile strength, bending strength and impact strength were evaluated as a function of type and amount of filler material in the POM matrix. In addition, the change in melt flow index of POM/filler mixtures was determined, before and after extrusion. Furthermore, the morphology of the specimens was examined via electron microscopy. The results of this investigation are encouraging and present an innovative approach to reutilize hydrolyzed electrostatic powder coating wastes with thermoset structures as fillers in acetal copolymers.     

Orientation Effects in Hybrid-Polymer Mixtures

Composites based on melts of boron-oxide oligomer (BOO) and low-density polyethylene (LDPE) in the polyoxide-concentration range of 0–64 vol % were synthesized. The measurements of the thermomechanical and mechanical properties of the composites showed the incompatibility of the mixture components. The abnormal increase in the strength and the Young’s modulus of the LDPE/boron-oxide oligomer mixtures under the tension of molded composite specimens was registered in the range of 25–50 vol % polyoxide. The anomalies were explained as being due to polyoxide-fiber formation and confirmed by the electron-microscopy images. The abnormal changes in the differential pressure in a melt flow and the torque of an extrusion auger were observed in the same polyoxide-concentration range, which was explained by the polyoxide orientation in a melt flow and its planar structure. The chemical structure of boron-oxide oligomer exposed to extrusion mixing and its distribution within a molded specimen of the mixture were analyzed by IR spectroscopy. The opportunity to synthesize hydrolytically stable composites in a wide range of ratios owing to the polyoxide encapsulation in a polyethylene matrix was shown.     

Characterization of elongation viscosity for polyethylene melts

Elongation viscosity is an important characterization of flow properties for polymer melts. In the present article, a new extensional viscosity equation for polymer melts was established by introducing a relaxation time equation based on the Cross model. The elongation viscosities of a low-density polyethylene (LDPE) melt at 200 °C and a metallocene linear low-density polyethylene (mLLDPE) melt at 130 °C were estimated using this equation; then, the calculations of the melt elongation viscosity were compared with the measured data from the extension experiments of the LDPE melt and the mLLDPE melt reported in the reference. Good agreement was found between the predictions and the measured data from the LDPE and mLLDPE melts. In addition, this equation is easy to use for characterization of elongation viscosity during single shaft elongation flow for polymer melts.     

Interfacially modified LDPE/GTR composites with non-polar elastomers: From microstructure to macro-behavior

This paper provides some new insights into the mechanism of interaction and modifications in thermoplastic composites based on low density polyethylene (LDPE), ground tire rubber (GTR) and non-polar elastomer. The composites were prepared using a co-rotating twin-screw extruder at variable LDPE/GTR ratio and constant elastomer content. Two types of commercial elastomer were applied: styrene-butadiene-styrene (SBS) block copolymers (Kraton^®) with different topologies (linear/branched) and partially cross-linked butyl rubbers (Kalar^®) with different Mooney viscosities. Processing characteristics, static mechanical properties (tensile strength, elongation at break, hardness), dynamic mechanical properties, thermal properties and morphology of the resulting thermoplastic composites were investigated. Microstructure analysis shows that modification of LDPE/GTR composites with non-polar elastomers caused encapsulation of GTR particles within the elastomer phase. This phenomenon has significant influence on macro-behavior of thermoplastic composites based on LDPE/GTR blends. The results indicate that SBS copolymer improves interfacial interactions between GTR and LDPE, which enhances mechanical and thermal properties of the composites. On the other hand, cross-linked butyl rubber showed partial compatibility with LDPE and low compatibility with GTR particles.     

Development of continuous process enabling nanofibrillation of pulp and melt compounding

Microfibrillated cellulose (MFC), a mechanically fibrillated pulp mostly consisting of nanofibrils, is a very attractive material because of its high elastic modulus and strength. Although much research has been done on composites of MFC and polypropylene (PP), it has been difficult to produce such composites at an industrial level because of the difficulties in using MFC in such composites are not only connected to the polarity (that can be improved with compatibilizers), but also with the challenge to make a homogeneous blend of the components, and also the low temperature stability of cellulose that could cause problems during processing. We developed a new processing method which enables continuous microfibrillation of pulp and its melt compounding with PP. Never-dried kraft pulp and powdered PP were used as raw materials to obtain MFC by kneading via a twin-screw extruder. Scanning electron microscopy showed nano to submicron wide fibers entangled in the powdered PP. MFC did not aggregate during the melt compounding process, during which the water content was evaporated. Maleic anhydride polypropylene (MAPP) was used as a compatibilizer to reinforce interfacial adhesion between the polar hydroxyl groups of MFC and non-polar PP. We investigated the effect of MAPP content on the mechanical properties of the composite, which were drastically improved by MAPP addition. Needle-leaf unbleached kraft pulp (NUKP)-derived MFC composites had better mechanical properties than needle-leaf bleached kraft pulp (NBKP)-derived MFC composites. Injection molded NUKP-derived MFC composites had good mechanical and thermal properties. The tensile modulus of 50 wt% MFC composite was two times, and the tensile strength 1.5 times higher than that of neat PP. The heat distortion temperature of 50 wt% MFC content composite under 1.82 MPa flexural load was increased by 53 °C, from 69 to 122 °C. This newly developed continuous process using powder resin has the potential for application at an industrial level.     

Rheological,morphological and mechanical properties of flax fiber polypropylene composites: influence of compatibilizers

In this work, the rheological, mechanical and morphological properties of flax fiber polypropylene composites were investigated. The effect of incorporating a polypropylene grafted acrylic acid or a polypropylene grafted maleic anhydride on these properties has been studied as well. According to scanning electron microscopic observations and tensile tests, the addition of a compatibilizer improved the interfacial adhesion between the flax fibers and the polymer matrix. The tensile modulus of composite containing 30 wt% flax fibers was improved by 200 % and the tensile strength improved by 60 % in comparison with the neat PP. Plasticizing effect of the compatibilizers as a result of their lower melt flow index was also shown to decrease the rheological properties of the composites, even though the effect was not pronounced on the mechanical properties.     

Application of cooling curve analysis in solidification pattern and structure control of grey cast irons

In this article, the composites based on long glass fibre reinforced polypropylene/intumescent flame retardant (LGFPP/IFR) were prepared by melt blending. The influence of thermal oxidative ageing on the LGFPP/IFR composites with different thermal oxidative ageing time at 140 °C was studied by means of oven heating. The thermal stability and flammability of the composites were respectively investigated by thermal gravimetric analysis (TG), limiting oxygen index (LOI), UL-94 test, cone calorimeter test (CCT), scanning electronic microscopy (SEM), mechanical properties test and energy-dispersive X-ray analysis (EDAX). A trend of increase first and then decrease in LOI values was shown in 0–50 days ageing, with the same trend as thermal stability obtained from TG in nitrogen condition. The CCT results indicated that the LGFPP/IFR composites after ageing achieved a higher heat release rate, which means a higher fire risk. The mechanical properties showed a global decrease in just 10 days ageing. Morphologies obtained from SEM showed that both the rupture of PP matrix and fibre interface debonding led to the decrease in mechanical properties. The EDAX proved that IFR particles could emerge and gather on the surface of sample in ageing procedure, which had great effects on the thermal stability and flame retardancy of the composites.     

Thermal and mechanical properties of particulate fillers filled epoxy composites for electronic packaging application

Epoxy composites containing particulate fillers‐fused silica, glass powder, and mineral silica were investigated to be used as substrate materials in electronic packaging application. The content of fillers were varied between 0 and 40 vol%. The effects of the fillers on the thermal properties—thermal stability, thermal expansion and dynamic mechanical properties of the epoxy composites were studied, and it was found that fused silica, glass powder, and mineral silica increase the thermal stability and dynamic thermal mechanical properties and reduce the coefficient of thermal expansion (CTE). The lowest CTE value was observed at a fused silica content of 40 vol% for the epoxy composites, which was traced to the effect of its nature of low intrinsic CTE value of the fillers. The mechanical properties of the epoxy composites were determined in both flexural and single‐edge notch (SEN‐T) fracture toughness properties. Highest flexural strength, stiffness, and toughness values were observed at fillers content of 40 vol% for all the filled epoxy composites. Scanning electron microscopy (SEM) micrograph showed poor filler–matrix interaction in glass powder filled epoxy composites at 40 vol%. Copyright © 2007 John Wiley & Sons, Ltd.     

Effects of the compatibilizer PE‐g‐GMA on the mechanical,thermal and morphological properties of virgin and reprocessed LDPE/corn starch blends

The effects of the compatibilizer polyethylene grafted with glycidyl methacrylate (PE‐g‐GMA) on the properties of low‐density polyethylene (LDPE) (virgin and reprocessed)/corn starch blends were studied. LDPE (virgin and reprocessed)/corn starch blends containing 30, 40 and 50 wt% starch, with or without compatibilizer, were prepared by extrusion and characterized by the melt flow index (MFI), tensile test, dynamic mechanical analysis (DMTA) and light microscopy. The addition of starch to LDPE reduced the MFI values, the tensile strength and the elongation at break, whereas the modulus increased. The decreases in the MFI and tensile properties were most evident when 40 and 50 wt% starch were added. Blends containing 3 wt% PE‐g‐GMA had higher tensile strength values and lower MFI values than blends without compatibilizer. Light microscopy showed that increasing the starch content resulted in a continuous phase of starch. Copyright © 2005 John Wiley & Sons, Ltd.     

Synergistic effects of zeolites on a novel intumescent flame-retardant low-density polyethylene (LDPE) system

A char forming agent and silica-gel microencapsulated APP were selected to form novel intumescent flame-retardant system (IFR) to prepare flame-retardant low-density polyethylene (LDPE) composites, and then the influence of zeolites on the thermal and flame-retardant properties of flame-retardant LDPE composites were studied. With the addition of 1 wt% zeolites to LDPE/IFR system, the LOI value increases from 29.0 to 34.0 %. The results of cone calorimetry show that the heat release rate peak and total heat release of the intumescent flame-retardant LDPE composite with 1 wt% zeolites decreases remarkably compared with that of without zeolites. The scanning electron microscopy indicates zeolites with suitable content can improve the quality of the char layer of flame-retardant LDPE composite which is more coherent and dense. The zeolites with the appropriate content can remarkably improve the flame-retardant properties of the LDPE composites.     

Thermal, mechanical and electrical properties of copper powder filled low-density and linear low-density polyethylene composites

Low-density polyethylene (LDPE) and linear low-density polyethylene (LLDPE) with different copper contents were prepared by melt mixing. The copper powder particle distributions were found to be relatively uniform at both low and high copper contents. There was cluster formation of copper particles at higher Cu contents, as well as the formation of percolation paths of copper in the PE matrices. The DSC results show that Cu content has little influence on the melting temperatures of LDPE and LLDPE in these composites. From melting enthalpy results it seems as if copper particles act as nucleating agents, giving rise to increased crystallinities of the polyethylene. The thermal stability of the LDPE filled with Cu powder is better than that for the unfilled polymer. The LLDPE composites show better stability only at lower Cu contents. Generally, the composites show poorer mechanical properties (except Young's modulus) compared to the unfilled polymers. The thermal and electrical conductivities of the composites were higher than that of the pure polyethylene matrix for both the LDPE and LLDPE. From these results the percolation concentration was determined as 18.7 vol.% copper for both polymers.     

Destructuration of cotton under elevated pressure

Dry and wet cotton linters were compressed under elevated pressure in a home-made Bridgman anvil press designed to reach 2.5 GPa and 180 °C. The structural organisation of cotton was changed under the joint action of temperature and pressure. Cotton having high moisture content shows that only a thin surface layer is partially destructured to a compact mat of nanofibres, while the initial cotton fibres are only deformed inside the sample. For dried cotton, the whole sample undergoes a destructuration into a compact mat of nanometre-sized fibres. The mechanical properties were studied by nano-indentation and dynamic mechanical analysis. Compressed dry cotton has higher modulus (10.3 GPa) than wet cotton (6.8 GPa). We postulate that the transverse elastic modulus of cotton microfibrils is around the value of 10 GPa. This work showed that nano-sized fibrils can also be separated in the solid state without flow, and re-compacted to form a solid object.