Vibration time series analysis of bubbling and turbulent fluidization

A non-intrusive vibration monitoring technique was used to study the hydrodynamics of a gas–solid fluidized bed. Experiments were carried out in a 15 cm diameter fluidized bed using 226, 470 and 700 μm sand particles at various gas velocities, covering both bubbling and turbulent regimes. Auto correlation function, mutual information function, Hurst exponent analysis and power spectral density function were used to analyze the fluidized bed hydrodynamics near the transition point from bubbling to turbulent fluidization regimes. The first pass of the autocorrelation function from one half and the time delay at which it becomes zero, and also the first minimum of the mutual information, occur at a higher time delay in comparison to stochastic systems, and the values of time delays were maximum at the bubbling to turbulent transition gas velocity. The maximum value of Hurst exponent of macro structure occurred at the onset of regime transition from bubbling to turbulent. Further increase in gas velocity after that regime transition velocity causes a decrease in the Hurst exponent of macro structure because of breakage of large bubbles to small ones. The results showed these methods are capable of detecting the regime transition from bubbling to turbulent fluidization conditions using vibration signals.     

Direct reduction of hematite powders in a fluidized bed reactor

Ultrafine hematite powder was reduced to produce ultrafine iron powder in a 50%Ar–50%H₂ atmosphere at 450–550 °C in a fluidized bed reactor. The ultrafine hematite powder shows the typical agglomerating fluidization behavior with large agglomerates fluidized at the bottom of the bed and small agglomerates fluidized at the upper part of the bed. It was found that defluidization occurred even at the low temperature of 450 °C with low metallization rate. Defluidization was attributed mainly to the sintering of the newly formed iron particles. Granuation was employed to improve the fluidization quality and to tackle the defluidization problem, where granules fluidized like a Geldart's group A powder. Granulation was found to effectively reduce defluidization during reduction, without however sacrificing reduction speed. The as-reduced iron powders from both the ultrafine and the granulated hematite exhibited excellent sintering activity, that is, fast sintering at temperature of as low as ～580 °C, which is much superior as compared to that of nano/ultrafine iron powders made by other processes.     

IMPROVEMENT OF FLUIDIZABILITY OF FINE POWDERS ——A COMPUTER STUDY

Simulations of the gas fluidization of a cohesive powder were performed using the Stokesian Dynamics method and an agglomeration-deagglomeration model to investigate methods of improving the fluidizability of fine powders. Three techniques (a) high gas velocity (b) vibration-assisted fluidization and (c) tapered fluidizer were used in the simulations which provided detailed information on the bed microscopy such as the motion of 1 O0 particles in a fluidizing vessel along with the formation and destruction of cohesive bonds dudng collisions. While all three techniques were found to effectively improve the fluidizability of a strongly cohesive powder, we suggest a combination of high velocity fluidization assisted by extemal vibration of the fluidized bed to minimize entrainment of particles.     

CFD-DEM investigation into flow characteristics in mixed pulsed fluidized bed under electrostatic effects

Static electricity has an important effect on gas–solid fluidized bed reactor fluidization performance. In the process of fluidization, electrostatic interaction between particles will obviously accelerate particle agglomerate formation, which consequently reduces the fluidization performance. Pulsed gas flow injection is an efficient method to enhance particle mixing, thereby weakening the occurrence of particle agglomerate. In this study, the two-dimensional hybrid pulsed fluidized bed is established. The flow characteristics are studied by using the coupled CFD-DEM numerical simulation model considering electrostatic effects. Influences of different pulsed frequencies and gas flow ratios on fluidized bed fluidization performance are investigated to obtain the optimal pulsed gas flow condition. Results show that in the presence of static electricity, the bubble generation position is lower, which is conducive to the particle flow. Pulsed gas flow can increase the particle velocity and improve the diffusion ability. The bubble generation time is different at different frequencies, and the frequency of 2.5 Hz has the most obvious effect on the flow characteristics. Different gas flow ratios have significant impacts on the particle movement amplitude. When the pulse gas flow accounts for a large ratio, the particle agglomerate tends to be larger. Therefore, in order to improve the fluidization effect, the ratio of pulsed gas flow to stable gas flow should be appropriately reduced to 0.5 or less.     

Two-fluid modeling of Geldart A particles in gas-fluidized beds

We have investigated the effect of cohesion and drag models on the bed hydrodynamics of Geldart A particles based on the two-fluid （TF） model. For a high gas velocity U0 = 0.03 m/s, we found a transition from the homogeneous fluidization to bubbling fluidization with an increase of the coefficient C1, which is used to account for the contribution of cohesion to the excess compressibility. Thus cohesion can play a role in the bed expansion of Geldart A particles. Apart from cohesion, we have also investigated the influence of the drag models. When using the Wen and Yu drag correlation with an exponent n = 4.65, we find an under-prediction of the bed expansion at low gas velocities （U0 = 0.009 m/s）. When using a larger exponent （n = 9.6）, as reported in experimental studies of gas-fluidization, a much better agreement with the experimental bed expansion is obtained. These findings suggest that at low gas velocity, a scale-down of the commonly used drag model is required. On the other hand, a scale-up of the commonly used drag model is necessary at high gas velocity （U0 = 0.2 and 0.06 m/s）. We therefore conclude that scaling the drag force represent only an ad hoc way of repairing the deficiencies of the TF model, and that a far more detailed study is required into the origin of the failure of the TF model for simulating fluidized beds of fine powders.     

Hydrodynamics and energy consumption studies in a three-phase liquid circulating three-phase fluid bed contactor

The hydrodynamics and energy consumption have been studied in a cold flow, bubbling and turbulent, pressurized gas–liquid–solid three-phase fluidized bed (0.15 m ID × 1 m height) with concurrent gas–liquid up flow is proposed with the intention of increasing the gas hold up. The hydrodynamic behaviour is described and characterised by some specific gas and liquid velocities. Particles are easily fluidized and can be uniformly distributed over the whole height of the column. The effect of parameters like liquid flow rate, gas flow rate, particle loading, particle size, and solid density on gas hold up and effect of gas flow rate, solid density and particle size on solid hold up, energy consumption and minimum fluidization velocity has been studied. At the elevated pressures a superior method for better prediction of minimum fluidization velocity and terminal settling velocities has been adopted. The results have been interpreted with Bernoulli’s theorem and Richardson–Zaki equation. Based on the assumption of the gas and liquid as a pretend fluid, a simplification has been made to predict the particle terminal settling velocities. The Richardson–Zaki parameter n′ was compared with Renzo’s results. A correlation has been proposed with the experimental results for the three-phase fluidization.     

MULTI-SCALE AGGREGATION OF PARTICLES IN GAS-SOLIDS FLUIDIZED BEDS

The multi-scale characteristics of clusters in a fast fluidized bed and of agglomerates in a fluidized bed of cohesive particles are discussed on the basis of large amounts of experiments.The cluster size and concentration are dominated by the local voidage of the bed.A cluster consists of many sub-clusters with different sizes and discrete par-ticles,and the sub-cluster size probability density distribution appears as a negative exponential function.The agglom-erates in a fluidized bed of cohesive particles also possess the multi-scale nature.The large agglomerates form a fixed bed at the bottom,the medium agglomerates are fluidized in the middle,and the small agglomerates and discrete parti-cles become the dilute-phase region in the upper part of the bed.The agglomerate size is mainly affected by cohesive forces and gas velocity.The present models for prediction the size of clusters and agglomerates can not tackle the in-trinsic mechanism of the multi-scale aggregation,and a challenging problem for establishing mechanistic model is put forward.     

颗粒聚合体碰撞破损的细观力学仿真研究

粉末和颗粒材料常常以聚合体(agglomerate,还可译成结块, 聚团等)的形式存在.无论是自然环境中还是工业处理过程中, 微小颗粒聚合体碰撞破损是一常见物理现象.近十几年来, 对颗粒聚合体碰撞研究在试验和数值模拟方面均取得了很大的进展.特别是利用颗粒离散元方法, 结合经典接触力学理论, 对微米颗粒聚合体碰撞破损的细观力学机理进行的研究, 取得了很多重要成果.基本形成了较为完善的模拟分析方法, 提出了许多新概念, 形成了目前适于分析研究的专用分析程序.本文介绍了目前国际上颗粒聚合体碰撞破损模拟研究的一般方法和理论, 总结了现有的主要研究内容及成果, 并提出一些研究展望.      

Flow regime diagrams for gas-solid fluidization and upward transport

Flow regime maps are presented for gas-solids fluidized beds and gas-solids upward transport lines. For conventional gas solids fluidization, the flow regimes include the fixed bed, bubbling fluidization, slugging fluidization and turbulent fluidization. For gas solids vertical transport operation, solids flux must be incorporated in the flow regime diagrams. The flow regimes then include dilute-phase transport, fast fluidization or turbulent flow, slug/bubbly flow, bubble-free dense-phase flow and packed bed flow. In practical circulating fluidized beds and transport risers, operation below the fast fluidization regime is commonly impossible due to equipment limitations. Practical flow regime maps are proposed with the flow regimes, including homogeneous dilute-phase flow, core-annular dilute-phase flow (where there are appreciable lateral gradients but small axial gradients) and fast fluidization (where there are both lateral and axial gradients). The boundary between fast fluidization and dilute-phase pneumatic transport is set by the type A choking velocity, at which the uniform suspension collapses and particles start to accumulate in the bottom region of the transport line, while the mechanism of transition from fast fluidization to dense-phase flow depends on the column and particle diameters.     

Hydrodynamic characteristics of a rectangular gas-driven inverse liquid-solid fluidized bed

The hydrodynamic characteristics of a rectangular gas-driven inverse liquid-solid fluidized bed (GDFB) using particles of different diameters and densities were investigated in detail. Rising gas bubbles cause a liquid upflow in the riser portion, enabling a liquid downflow that causes an inverse fluidization in the downer portion. Four flow regimes (fixed bed regime, initial fluidization regime, complete fluidization regime, and circulating fluidization regime) and three transition gas velocities (initial fluidization gas velocity, minimum fluidization gas velocity, and circulating fluidization gas velocity) were identified via visual observation and by monitoring the variations in the pressure drop. The axial local bed voidage (ε) of the downer first decreases and then increases with the increase of the gas velocity. Both the liquid circulation velocity and the average particle velocity inside the downer increase with the increase of the gas velocity in the riser, but decrease with the particle loading. An empirical formula was proposed to successfully predict the Richardson-Zaki index “n”, and the predicted ε obtained from this formula has a ±5% relative error when compared with the experimental ε.     

Flowability of various dusts collected from secondary copper smelter off-gas

Stable flow of off-gas dust from dust collector hoppers and storage silos is important for smooth operation. Flow properties of the collected off-gas dust are critical to achieve suitable flow. Various dust samples collected from secondary copper smelter off-gases were studied. The median diameter of the fine-grained dusts varied from 0.8 to 1.4 μm and the flowability ranged from “cohesive” to “very cohesive”. The flowability of shaft and anode furnace dust improved slightly with increasing consolidation stress and their wall friction angles decreased, which is a typical behavior. In contrast, the flowability of converter dust decreased with increasing consolidation stress and its wall friction angles increased. Pre-shear treatment of converter dust worsened its flowability, increased the wall friction angle, and improved the flowability with increasing consolidation stress. This is believed to occur because pre-shear treatment fragments small agglomerates in the dust that improve flowability. The presence of such agglomerates was confirmed by sieving tests. A diagrammatic representation of the flowability showing that the unconfined yield strength is dependent on consolidation stress can be improved by using logarithmically scaled axes.     

CFD–DEM simulation of the pneumatic conveying of fine particles through a horizontal slit

Fine particles play a significant role in many industrial processes. To study the dynamic behavior of fine particle and their deposition in rock fractures, the pneumatic conveying of fine particles (approximately 100 μm in diameter) through a small-scale horizontal slit (0.41 m × 0.025 m) was studied, which is useful for the sealing technology of underground gas drainage in coal mining production. The CFD–DEM method was adopted to model the gas-particle two-phase flow; the gas phase was treated as a continuum and modeled using computational fluid dynamics (CFD), particle motion and collisions were simulated using the DEM code. Then, the bulk movement of fine particles through a small-scale horizontal slit was explored numerically, and the flow patterns were further investigated by visual inspection. The simulation results indicated that stratified flow or dune flow can be observed at low gas velocities. For intermediate gas velocities, the flow patterns showed pulsation phenomena, and dune flow reappeared in the tail section. Moreover, periodic flow regimes with alternating thick and sparse stream structures were observed at a high gas velocity. The simulation results of the bulk movement of fine particles were in good agreement with the experimental findings, which were obtained by video-imaging experiments. Furthermore, the calculated pressure drop versus gas velocity profile was investigated and compared with relative experimental findings, and the results showed good agreement. Furthermore, the particle velocity vectors and voidage distribution were numerically simulated. Selected stimulation results are presented and provide a reference for the further study of fine particles.     

Hydrodynamics of a bubble-induced inverse fluidized bed reactor with a nanobubble tray

This paper reports on the hydrodynamics of a bubble-induced inverse fluidized bed reactor, using a nanobubble tray gas distributor, where solid particles are fluidized only by an upward gas flow. Increasing the gas velocity, the fixed layer of particles initially packed at the top of the liquid starts to move downwards, due to the rise of bubbles in this system, and then gradually expands downwards until fully suspended. The axial local pressure drops and standard deviation were examined to delineate the flow regime comprehensively under different superficial gas velocities. Four flow regimes (fixed bed regime, initial fluidization regime, expanded regime, and post-homogeneous regime) were observed and three transitional gas velocities (the initial fluidization velocity, minimum fluidization velocity, and homogeneous fluidization velocity) were identified to demarcate the flow regime. Three correlations were developed for the three transitional velocities. As the fine bubbles generated from the nanobubble tray gas distributor are well distributed in the entire column, the bed expansion process of the particles is relatively steady.     

Experimental investigation on micro-dynamic behavior of gas explosion suppression with SiO2 fine powders

To study the effect of inert dust on gas explosion suppression mechanism, SiO₂ fine powders were sprayed to suppress premixed CH₄-Air gas explosion in a 20 L spherical experimental system. In the experiment, high speed schlieren image system was adopted to record explosion flame propagation behaviors, meanwhile, pressure transducers and ion current probes were used to clearly record the explosion flame dynamic characteristics. The experimental results show that the SiO₂ fine powders suppressed evidently the gas explosion flame, and reduced the peak value of pressure and flame speed by more than 40 %. The ion current result shows that the SiO₂ super fine powders were easy to contact with and absorb free radicals near the combustion reaction region, which greatly reduced the combustion reaction intensity, and in turn influenced the flame propagation and pressure rising.     

Study of material agglomeration during nozzle injection of multiviscosity liquid into a fluidized bed reactor by the electric conductance method

Fluidized bed agglomeration is an important and challenging problem for thermal cracking in fluid cokers. A low coker temperature can be problematic because the bitumen is injected into the fluidized bed with a different viscosity, resulting in formation of agglomerates of varying sizes, which slows the cracking reactions. In the present study, the bed material agglomeration process during nozzle injection of multiviscosity liquid was investigated in a fluidized bed operated at different mass ratios of the atomization gas to the liquid jets (GLR = 1%–3.5%) and gas velocities (3.9U_mf and 5.9U_mf) based on a conductance method using a water–sand system to simulate the hot bitumen–coke system at room temperature. During the tests of liquid-jet dispersion throughout the bed, different agglomeration stages are observed at both gas velocities. The critical amount of tert-butanol in the liquid jets that could lead to severe agglomeration of the bed materials (poor fluidization) at GLR = 1% is about 10 wt% at the low fluidizing gas velocity (3.9U_mf) and 18 wt% at the high gas velocity (5.9U_mf). This study provides a new approach for on-line monitoring of bed agglomeration during liquid injection to guarantee perfect contact between the atomized liquid and the bed particles.     

Bubble behaviors of geldart B particle in a pseudo two-dimensional pressurized fluidized bed

Pressurized fluidized beds have been developed in quite a few industrial applications because of intensified heat and mass transfer and chemical reaction. The bubble behaviors under elevated pressure, strongly influencing the fluidization and reaction conversion of the whole system, are of great research significance. In this work, the bubble behaviors of Geldart B particle in a pseudo two-dimensional (2D) pressurized fluidized bed were experimentally studied based on digital image analysis technique. The effects of pressure and fluidization gas velocity on the general bubble behaviors (i.e., size, shape and spatial distribution) and the dynamic characteristics, such as the time-evolution of voidage distribution and local flow regimes, were comprehensively investigated. Results show that increasing pressure reduces the stability of bubbles and facilitates gas passing through the emulsion phase, resulting in the “smoother” fluidization state with smaller bubbles and declined bubble fraction and standard deviation. The equivalent bubble diameter and bubble aspect ratio increase with the increasing gas velocity while decrease as pressure rises. The elevated pressure reduces bubbles extension in the vertical direction, prohibits the “short pass” of fluidization gas in large oblong bubbles/slugs and benefits the gas–solid interaction. The flow regimes variation with gas velocity is affected by the elevated pressure, and demonstrates different features in different local positions of the bed.     

Experimental study of the effect of friction phenomena on actual and calculated inventory in a small-scale CFB riser

Accurate information concerning riser inventory in a fluidized bed is required in some applications such as the calcium looping process, because it is related to the CO₂ capture efficiency of the system. In a circulating fluidized bed (CFB), the riser inventory is normally calculated from the riser pressure drop; however, the friction and the acceleration phenomena may have a significant influence on the total riser pressure drop. Therefore, deviation may occur in the calculation from the actual mass. For this reason the magnitude of the friction and the acceleration pressure drop in the entire riser is studied in small-scale risers. Two series of studies were performed: the first one in a scaled cold model riser of the 10 kW_th facility, and the second one in the 10 kW_th fluidized bed riser under process conditions. The velocities were chosen to comply with the fluidization regimes suitable for the calcium looping process, namely, the turbulent and the fast. In cold-model experiments in a low-velocity turbulent fluidization regime, the actual weight (static pressure drop) of the particles is observed more than the weight calculated from a recorded pressure drop. This phenomenon is also repeated in pilot plant conditions. In the cold-model setup, the friction and acceleration pressure drop became apparent in the fast fluidization regime, and increased as the gas velocity rose. Within calcium looping conditions in the pilot plant operation, the static pressure drop was observed more than the recorded pressure drop. Therefore, as a conservative approach, the influence of friction pressure drop may be neglected while calculating the solid inventory of the riser. The concept of transit inventory is introduced as a fraction of total inventory, which lies in freefall zones of the CFB system. This fraction increases as gas velocity rises.     

Preparation of spherical Y2SiO5 powders for thermal-spray coating

Yttrium silicate, for its high oxidation resistance, is an important candidate for protective coating for carbon-fiber-reinforced composites at temperatures above 1600 ℃. A novel method, consisting of coprecipitation, spray-drying, heat-treatment and plasma-densification, is developed to prepare Y2SiO5 powders for thermal-spraying. The composition, morphology and flowability of the synthesized Y2SiO5 powders are investigated by XRD, SEM and Hall Flowmeter, respectively. The results show that the synthesized Y2SiO5 powders are nearly spherical with high purity. The apparent density and flowability of the Y2SiO5 powders are 1.87 g/cm^3 and 37 s/50 g, respectively, which lead to a high deposition efficiency of up to 80700 for atmospheric plasma spraying.     

Characteristics of turbulent particle transport in human airways under steady and cyclic flows

Motion of monodispersed aerosol particles suspended in air flow has been studied on realistic transparent model of human airways using Phase Doppler Particle Analyser (P/DPA). Time-resolved velocity data for particles in size range 1–8 μm were processed using Fuzzy Slotting Technique to estimate the power spectral density (PSD) of velocity fluctuations. The optimum processing setup for our data was found and recommendations for future experiments to improve PSD quality were suggested. Typical PSD plots at mainstream positions of the trachea and the upper bronchi are documented and differences among (1) steady-flow regimes and equivalent cyclic breathing regimes, (2) inspiration and expiration breathing phase and (3) behaviour of particles of different sizes are described in several positions of the airway model. Systematically higher level of velocity fluctuations in the upper part of the frequency range (30–500 Hz) was found for cyclic flows in comparison with corresponding steady flows. Expiratory flows in both the steady and cyclic cases produce more high-frequency fluctuations compared to inspiratory flows. Negligible differences were found for flow of particles in the inspected size range 1–8 μm at frequencies below 500 Hz. This finding was explained by Stokes number analysis. Implied match of the air and particle flows thereby indicates turbulent diffusion as important deposition mechanism and confirms the capability to use the P/DPA data as the air flow velocity estimate.     

Fluidization and bubbling behavior of potash particles in a deep fluidized bed

Most existing models for predicting bubble size and bubble frequency have been developed for freely bubbling fluidized beds. Accurate prediction of bubbling behavior in deep fluidized beds, however, has been a challenge due to the higher degree of bubble coalescence and break up, high probability of the slugging regime, partial fluidization, and chaotic behavior in the bubbling regime. In this work, the bubbling and fluidization behavior of potash particles was investigated in a deep fluidized bed employing a twin-plane electrical capacitance tomography (ECT) system. Solid volume fraction, average bubble velocity, average bubble diameter, and bubble frequency in both bubbling and slugging regimes were measured at two different bed height ratios (H/D = 3.5 and H/D = 3.78). This work is the first to illustrate a sequential view of bubbles at different superficial gas velocities in a fluidized bed. The results show that both the bubble diameter and rising velocity increased with increasing the superficial gas velocity for the two bed heights, with larger values observed in the deeper bed compared to the shallower one. Predicted values for bubble diameter, bubble rise velocity and bubble frequency from different models are compared with the experimental data obtained from the ECT system in this work. Good agreement has been achieved between the values predicted by the previous models and the experimental data for the bubble diameter and bubble rise velocity with an average absolute deviation of 16% and 15% for the bed height of 49 cm and 13% and 8% for the bed height of 53 cm, respectively.