Size-based speciation of iron in clay mineral particles by gravitational field-flow fractionation with electrothermal atomic absorption spectrometry

Gravitational field-flow fractionation (FFF) coupled to UV and ETAAS detectors has been tested for micron-size particles in the range of 5–20 μm using three Fe-rich clay samples. The iron content estimated after aqua regia extraction was about 20–40 mg kg⁻¹. The ETAAS analysis was performed both off-line from collected fractions and in an online continuous sampling mode using a specially designed flow through vial placed in the autosampler of the ETAAS. Comparison of the direct injection method with total analysis after aqua regia digestion shows that slurry injection of the dilute samples in the gravitational field-flow fractionation (GrFFF) effluent is quite efficient in these samples. In the majority of cases, more than 90% recovery was obtained for the slurry injection method. Fe mass-based particle size distributions and Fe concentration versus particle diameter plots can be generated using certain assumptions. This provides detailed information on size-based speciation of particulate samples. Generally, the Fe concentrations in the particles decreased slightly with an increase in particle size as is often found for soil and sediment samples.     

Comparative study of optimised BCR sequential extraction scheme and acid leaching of elements in the certified reference material NIST 2711

The optimised BCR sequential extraction procedure and a 4 h 1 mol L⁻¹ HCl partial extraction have been performed on the NIST 2711 reference material for a suite of 12 elements (Cd, Sb, Pb, Al, Cr, Mn, Fe, Co, Ni, Cu, Zn, As) using magnetic sector ICP-MS. A pseudo-total aqua regia digest of NIST 2711 has also been undertaken for quality assurance purposes, and comparison of the sum of the four BCR fractions, which included an aqua regia digest on the residue, with the pseudo-total aqua regia digest has been used to assess the accuracy of the BCR partitioning approach. As a result of this work, discrepancies between previous studies about BCR partitioning of elements in NIST 2711 have been discussed and an increase in confidence about the use of BCR partitioning scheme on seven elements (Cd, Pb, Al, Mn, Fe, Cu, Zn) in this standard material has been obtained. On the other hand, BCR partitioning for Sb, Cr, Co, Ni and As has been provided for the first time. Partial extraction results are also reported for the same 12 elements analysed by the optimised BCR procedure, with the partial extraction results exhibiting a strong correlation with the sum of the three labile steps of the BCR procedure.     

Investigation of distribution of beryllium, nickel and vanadium in subsoil of Csepel-Island

In order to investigate the long-term effect of the Százhalombatta power plant on the environment of the Csepel-Island subsoil samples were collected in 55 points within 200 km². Using a microwave-assisted extraction procedure, Be, Ni and V were extracted from the soil samples by aqua regia and the metal concentrations were determined by inductively coupled plasma mass spectrometry (ICP-MS). The analytical results were evaluated by chemometric methods and interpreted considering the main mineral constituents of the subsoil.     

Fractionation of potentially toxic elements in urban soils from five European cities by means of a harmonised sequential extraction procedure

The revised (four-step) BCR sequential extraction procedure has been applied to fractionate the chromium, copper, iron, manganese, nickel, lead and zinc contents in urban soil samples from public-access areas in five European cities. A preliminary inter-laboratory comparison was conducted and showed that data obtained by different laboratories participating in the study were sufficiently harmonious for comparisons to be made between cities and land types (e.g. parks, roadside, riverbanks, etc.). Analyte recoveries by sequential extraction, with respect to direct aqua regia digestion, were generally acceptable (100 ± 15%). Iron, nickel and, at most sites, chromium were found mainly in association with the residual phase of the soil matrix. Copper was present in the reducible, oxidisable and residual fractions, whilst zinc was found in all four sequential extracts. Manganese was strongly associated with reducible material as, in some cities, was lead. This is of concern because high lead concentrations were present in some soils (>500 mg kg⁻¹) and the potential exists for remobilisation under reducing conditions. As would be expected, extractable metal contents were generally highest in older, more heavily industrialised cities. Copper, lead and zinc showed marked (and often correlated) variations in concentrations between sites within the same city whereas manganese and, especially, iron, did not. No overall relationships were, however, found between analyte concentrations and land use, nor between analyte partitioning and land use.     

封闭压力酸溶-ICP-MS法分析地质样品中47个元素的评价

对封闭压力酸溶－ICP－MS法同时测定地质样品中47个元素的效果和适用范围进行了实测评价。并对溶样条件进行了优化。实验结果表明，HF－HNO3高温高压酸溶是一种有效的样品分解方法，在所测定的47个元素中，大部分元素如Li,Be,Ti,V,Mn,Co,Ni,Cu,Zn,As,Zr,Nb,Mo,Cd,In,Sn,Sb,Hf,Ta,W,Tl,Pb,Bi等在大多数标样中在三种取样量下都可以得到满意的回收率。而Sc,Cr,Ga,Y,REE,Rb,Cs,Sr,Ba,Th,U等元素在大部分样品中则随取样量减少，回收率上升，在一些样品中，当取样量降至25mg时，可以获得满意的回收率。用王水代替HNO3复溶残渣，利用氯离子的络合作用促进复溶，使许多元素的回收率有了明显的提高。     

Determination of Se in biological samples by axial view inductively coupled plasma optical emission spectrometry after digestion with aqua regia and on-line chemical vapor generation

A simple and fast method for the determination of Se in biological samples, including food, by axial view inductively coupled plasma optical emission spectrometry using on-line chemical vapor generation (CVG–ICP OES) is proposed. The concentrations of HCl and NaBH₄, used in the chemical vapor generation were optimized by factorial analysis. Six certified materials (non-fat milk powder, lobster hepatopancreas, human hair, whole egg powder, oyster tissue, and lyophilised pig kidney) were treated with 10 mL of aqua regia in a microwave system under reflux for 15 min followed by additional 15 min in an ultrasonic bath. The solutions were transferred to a 100 mL volumetric flask and the final volume was made up with water. The Se was determined directly in these solutions by CVG–ICP OES, using the analytical line at 196.026 nm. Calibration against aqueous standards in 10% v/v aqua regia in the concentration range of 0.5–10.0 µg L^− 1 Se(IV) was used for the analysis. The quantification limit, considering a 0.5 g sample weight in a final volume of 100 mL^− 1 was 0.10 µg g^− 1. The obtained concentration values were in agreement with the total certified concentrations, according to the t-test for a 95% confidence level.     

On-site preconcentration and trace metal ions determination in the Okavango Delta water system, Botswana

Microcolumns containing 8-hydroxyquinoline azo-immobilized on controlled pore glass were incorporated in a field sampler for on-site collection, isolation and preconcentration of trace metal ions in waters of the Okavango Delta, Botswana. Sequestered trace metal ions were recovered by elution with 0.5 ml of 1.5 M nitric acid, and determined by graphite furnace atomic absorption spectrometry (GFAAS). This sampling and enrichment method minimizes sample contamination, and collection of large volumes of water samples for transporting, over long distances, to analytical laboratories is avoided.Data reported comprise one of the initial surveys on trace metal ion concentrations in waters of the Okavango Delta, Botswana. In waters with more efficient mixing, dissolved metal ion concentrations found were generally low with slightly elevated levels of manganese (7-19 μg l⁻¹), zinc (2.7-4.8 μg l⁻¹), nickel (0.2-2.5 μg l⁻¹) and copper (0.3-2.1 μg l⁻¹). For each trace metal ion, concentration levels seem to reflect zones of varying water conveyance, and show no obvious temporal and spatial variations apart from a slight increment from the inlet in the upper Delta to the outlets in the lower Delta.     

Influence of sample pre-treatment on the determination of trace silver and cadmium in geological and environmental samples by quadrupole inductively coupled plasma mass spectrometry

The suitability of three different digestion procedures has been evaluated with regard to the quantitative determination of trace amounts of silver and cadmium in geological and environmental samples. Procedure A: extraction with aqua regia in an open vessel system; Procedure B: extraction with aqua regia in a closed pressurized vessel system; Procedure C: digestion with HF + HNO₃ in a closed pressurized vessel system. It was found that procedure A represented an effective way of extracting analytes from different types of geological samples while the effect of extracting interfering metals is low. Because it is interference-free, poses a low risk of contamination and is time-saving, sample treatment procedure A was preferred. For this digestion procedure, a series of Chinese geological reference materials was determined by ICP-MS, the results of which were found to be in reasonable agreement with the certified values.     

Oxidative extraction versus total decomposition of soil in the determination of thallium

An aqua regia extraction and a total decomposition of soil were compared in terms of thallium determination. A sequential extraction of soil, according to the BCR protocol, was also performed for additional information on thallium distribution in soil fractions. Certified reference material—soil GBW 07401 of Chinese origin, containing 1 ± 0.2 ppm of thallium was used in these experiments. Thallium was determined by flow injection-differential pulse-anodic stripping voltammetry (FI-DP-ASV). Only 35% of total thallium was extracted in the aqua regia extraction, while the total decomposition led to satisfactory recovery. The sequential extraction showed that only 5% of thallium in GBW 07401 is dissolvable in the four BCR procedure fractions, and that 95% of the element is entrapped in the residual parent matter. These results show that the aqua regia extraction does not ensure complete thallium extraction from soil. Surprisingly, the total decomposition is significantly less time consuming than the aqua regia extraction.     

Separation of trace amounts of Ga and Ge in aqueous solution using nano-particles micro-column

A simple and rapid analytical method for the separation of trace amounts of gallium and germanium from aqueous solution by solid-phase extraction with nano-particles was developed. It was found that only Ga(III) could be quantitatively retained on nano-SiO₂ in the pH range of 3-4 and 8-12 while Ge(IV) was not adsorbed, but both Ga(III) and Ge(IV) ions could be adsorbed quantitatively on nano-TiO₂ within the pH range of 4-11. These two ions adsorbed by nano-particles could be desorbed quantitatively. Effects of acidity, concentration of elution solution and interfering ions on the recovery of the analytes were systematically investigated. The sorption data could be well interpreted by the Langmuir model. Based on the Langmuir model equation, the monolayer adsorption capacity of nano-SiO₂/nano-TiO₂ was calculated to be 4.26 mg g⁻¹/19.68 mg g⁻¹ for Ga(III)/Ge(IV). Moreover, thermodynamic functions, the change of free energy (ΔG⁰), enthalpy (ΔH⁰) and entropy (ΔS⁰) of the adsorption reaction were estimated for each metal ion. Experimental data were also evaluated in terms of kinetic characteristics of adsorption and the adsorption process for both metal ions followed well pseudo-second-order kinetics. Finally, the proposed method was applied to the determination of trace Ga(III) and Ge(IV) in some water samples using loaded nano-particles columns, and it is found that the recoveries of Ga(III) and Ge(IV) were obtained to be in the range of 96.4-105.0%. And the method was validated with certified reference material (GBW07311, GBW 07406) and the values obtained for Ga(III) and Ge(IV) were in good agreement with the certified values.     

Novel surface molecularly imprinted material modified multi-walled carbon nanotubes as solid-phase extraction sorbent for selective extraction gallium ion from fly ash

A new gallium (Ga(III)) ion-imprinted multi-walled carbon nanotubes (CNTs) composite sorbent was synthesized by a surface imprinting technique. The Ga(III) ion-imprinted/multi-walled carbon nanotubes (Ga(III)-imprinted/CNTs) sorbent was characterized by Fourier transform infrared (FT-IR), X-ray diffraction (XRD), nitrogen adsorption experiment, static adsorption experiment, and solid-phase extraction (SPE) experiment. The effects of sample volume, sample pH, washing and elution conditions on the extraction of Ga(III) ion from real sample were studied in detail. The imprinted sorbent offered a fast kinetics for the adsorption of Ga(III). The maximum static adsorption capacity of the imprinted sorbent towards was 58.8 μmol g⁻¹. The largest selectivity coefficient for Ga(III) in the presence of Al(III) was over 57.3. Compared with non-imprinted sorbent, the imprinted sorbent showed good imprinting effect for Ga(III) ion, the imprinting factor (α) was 2.6, the selectivity factor (β) was 2.4 and 2.9 for Al(III) and Zn(II), respectively. The developed imprinted SPE method was applied successfully to the detection of trace Ga(III) ion in fly ash samples with satisfactory results.     

Determination of water soluble trace metals in airborne particulate matter using a dynamic extraction procedure with on-line inductively coupled plasma optical emission spectrometric detection

A novel continuous-flow system for the dynamic extraction of water soluble metal fractions in airborne particulate matter (APM) with subsequent inductively coupled plasma optical emission spectrometric (ICP-OES) analysis of derived extracts is presented. The fully automated extraction system with on-line multi-element detection offers enhanced sensitivity when compared to batch-wise counterparts; additionally it provides information about the extraction process. With the developed procedure detection limits in the order of 1.5 (Ba) to 8.0 (Ni) ng extractable mass per investigated sample could be achieved, which translates to method detection limits for soluble metal concentrations in APM ranging from 0.2 ng m⁻³ (Ba) to 0.9 ng m⁻³ (Fe). Reproducibility of analysis was determined by replicate measurement (n = 6) of an APM sample with an aerodynamic diameter ≤10 μm (PM10), derived results varied between 3.5% (Mn) and 12.1% (Ni) relative standard deviation. Method validation was accomplished by comparison of extracted soluble and remaining non-soluble fractions with the total metal contents of the investigated PM10 samples, showing an excellent mass balance for all elements. Application of the developed procedure for the analysis of water soluble metal fractions in PM10 samples (n = 16) from Linz (Austria) indicated a high variability of extractable fractions ranging from 11.7 ± 7.2% (Fe) to 48.8 ± 15.4% (Mn) of the total metal contents.     

Determination of thallium in sediments of the River Elbe using isotope dilution mass spectrometry with thermal ionization.

By using isotope dilution mass spectrometry with thermal ionization, TI concentrations were determined in sediments from six sampling positions of the River Elbe in the area of the former GDR (Bad Schandau, Dresden, Barby, Magdeburg, Werben/Havel and Cumlosen). For comparison, two samples from the River Rhine near Emmerich taken in 1978 and 1990 and the Community Bureau of Reference (BCR) certified reference material (CRM) 320 River Sediment were also analysed. Thallium concentrations after complete decomposition by high-pressure digestion (HNO3 + HF) and aqua regia [HCI-HNO3 (3 + 1)] ranged from 537 micrograms kg-1 in the BCR CRM 320 to 5192 micrograms kg-1 in the River Rhine sediment (1978) near Emmerich. The reproducibility of the method ranged from 0.06 to 4.7%. Only 49-94% of the total amount of TI was found after extraction with 1 mol dm-3 HNO3 and 43-86% after extraction with aqua regia. Sediments from Dresden, Barby, Werben/Havel and Cumlosen were found to have virtually identical TI concentrations as the River Rhine sediment sampled in 1990. In comparison with the extremely high Hg and As concentrations found in the River Elbe in an earlier study, the TI concentrations were not as high as expected.     

Heavy metals in river sediments — A chemometrical evaluation

First results are presented to support decisions within projects of recultivation in the Merseburg region. From two places of the river Luppe eight sediment samples were taken at four different days. The total concentrations of Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Zn were determined by ICP-AES after digestion with aqua regia both in the gross samples and in four particle size fractions obtained by wet sieving. Subsequently each fraction was split into six classes by a sequential extraction to characterise the pattern of heavy metal binding form. Questions about the difference of the regions, the importance of the particle size fractions, the mobility of the metals, and the influence of the seasonal factor were tried to answer by the help of chemometrical methods. It was possible to show that the two sampling places situated only about 7 km from each other have different total metal concentrations as well as different binding form patterns. The trend of the heavy metal enrichment in the smallest particle size fraction can easily be seen in two-dimensional diagrams, but could in general not be confirmed statistically for all metals. The consideration of all four factors together (region, particle size fraction, mobilisation class, and time) shows the significant influence caused by all factors and all interactions. Multivariate covariance analysis is used to include also the influence of sampling conditions.Dedicated on the occasion of his 70th birthday to Professor Dr. Klaus Doerffel, who has spent much of his life in teaching and introducing statistical and other chemometrical techniques in Analytical Chemistry     

Total metal concentrations in serum of dialysis patients and fractionation of Cu, Rb, Al, Fe and Zn in spent continuous ambulatory peritoneal dialysis fluids

Total metal concentrations were determined in the serum of 12 continuous ambulatory peritoneal dialysis (CAPD) patients and in fresh and spent CAPD fluids by electrothermal and flame atomic absorption spectrometry (ETAAS, FAAS). Concentrations of Cu in serum of CAPD patients ranged from 720 to 1780 ng cm⁻³, Rb from 128 to 346 ng cm⁻³, Al from 10 to 72 ng cm⁻³, Fe from 800 to 2300 ng cm⁻³ and Zn from 659 to 1310 ng cm⁻³. The accuracy of the analytical procedure was checked by the analysis of the reference material Seronom™, Trace Elements in Serum. Good agreement between the certified and determined values was obtained for Al, Cu, Fe and Zn. The data on the total metal concentrations in CAPD fluids indicated that during CAPD fluid exchange the losses of Cu from 5.0 to 35 ng cm⁻³, of Rb from 50 to 110 ng cm⁻³ and of Al from 3.0 to 14.0 ng cm⁻³ occurred through the peritoneal membrane. Although fresh CAPD fluids contained traces of Fe (3.0-5.0 ng cm⁻³), the transfer of this element took place through the peritoneal membrane into spent CAPD fluid (13.0-38.0 ng cm⁻³). Zn concentrations were in general lower in spent (20.0-80 ng cm⁻³) than in fresh CAPD fluids (∼100 ng cm⁻³). To follow the mechanisms of the transfer of trace elements through the peritoneal membrane of CAPD patients, fractionation of metals was carried out in spent CAPD fluids by size exclusion chromatography with UV and AAS detection, applying Superdex HR 10/30 column. The chromatographic run was followed at 278 nm and separated metal species also determined ‘off line’ in 1 cm³ fractions by ETAAS or FAAS. From the UV chromatograms and AAS analysis of trace elements in the separated fractions it was demonstrated that Cu, Al, Fe and Zn were bound to proteins and only partially to low molecular weight (LMW) species, while Rb was associated exclusively with LMW species. For characterisation of the high molecular weight (HMW) binding proteins, fractions containing trace elements were subjected to SDS-PAGE electrophoresis. Al and Fe were presumably bound to transferrin, but due to its low concentration in spent CAPD fluids, it was not possible to confirm its presence in the separated fractions. About 10% of Al and 15% of Fe corresponded to LMW species. A fraction of HMW proteins of Cu in spent CAPD fluids was most probably bound to albumin and Zn to albumin and globulins. About 50% of Cu and Zn existed in LMW proteins, while Zn was also found partially in ionic form.     

Hydride generation atomic fluorescence spectrometric determination of As, Bi, Sb, Se(IV) and Te(IV) in aqua regia extracts from atmospheric particulate matter using multivariate optimization

A highly sensitive and simple method, based on hydride generation and atomic fluorescence detection, has been developed for the determination of As, Bi, Sb, Se(IV) and Te(IV) in aqua regia extracts from atmospheric particulate matter samples. Atmospheric particulates matter was collected on glass fiber filters using a medium volume sampler (PM1 particulate matter). Two-level factorial designs have been used to optimise the hydride generation atomic fluorescence spectrometry (HG-AFS) procedure. The effects of several parameters affecting the hydride generation efficiency (hydrochloric acid, sodium tetrahydroborate and potassium iodide concentrations and flow rates) have been evaluated using a Plackett-Burman experimental design. In addition, parameters affecting the hydride measurement (delay, analysis and memory times) have been also investigated. The significant parameters obtained (sodium tetrahydroborate concentration, sodium tetrahydroborate flow rate and analysis time for As; hydrochloric acid concentration and sodium tetrahydroborate flow rate for Se(IV); and sodium tetrahydroborate concentration and sodium tetrahydroborate flow rate for Te(IV)) have been optimized by using 2ⁿ + star central composite design. Hydrochloric acid concentration and sodium tetrahydroborate flow rate were the significant parameters obtained for Sb and Bi determination, respectively. Using a univariate approach these parameters were optimized. The accuracy of methods have been verified by using several certified reference materials: SRM 1648 (urban particulate matter) and SRM 1649a (urban dust). Detection limits in the range of 6 × 10⁻³ to 0.2 ng m⁻³ have been achieved. The developed methods were applied to several atmospheric particulate matter samples corresponding to A Coruña city (NW Spain).     

Rapid derivative spectrophotometric method for the determination of platinum in Pt-Ru/C catalyst using iodide media.

A rapid spectrophotometric method for the determination of platinum in 20% Pt-Ru (Pt:Ru (1:1)) carbon-supported catalyst has been developed. The samples of catalyst (0.85-12.60 mg) have been digested 1) in aqua regia after preliminary separation of carbon by burning or 2) directly in aqua regia in the presence of carbon. The detection of platinum was carried out in the obtained solutions after conversion of the metal into the iodide complex. The interfering effect of ruthenium on the detection of platinum was eliminated by the use of derivative spectrophotometry. Platinum was selectively determined by numerical calculation of the 4th-order-derivative absorption spectrum of the mixture of iodide complexes of both metals.     

Determination of palladium(II) with picramine-epsilon

We found a reaction of palladium(II) with picramine-epsilon to give a colored complex with an absorption maximum at 556 nm and a molar absorption coefficient of (2.01 ± 0.02) × 10⁴. Conditions of spectrophotometric reaction were selected for determining palladium(II) in nitric acid solutions or solutions containing aqua regia without the conversion of initial complexes into other forms. A rapid procedure was developed for the direct spectrophotometric determination of palladium(II) in concentrations down to 0.5 mg/L in various process solutions (including those containing nitric acid and aqua regia) within 15 min.     

Assessment of a geochemical extraction procedure to determine the solid phase fractionation and bioaccessibility of potentially harmful elements in soils: A case study using the NIST 2710 reference soil

Three mineral acid sequential extraction regimes (HNO₃ only, HNO₃ followed by HCl and aqua regia) were applied to the NIST 2710 contaminated reference soil. The major and trace element chemical analysis data from the extractions were subjected to a chemometric self-modelling mixture resolution procedure which identified that 12 distinct physico-chemical components were extracted. The fractionation of As, Cd, Ni and Pb between these components were determined. Tentative assignments of the mineralogical sources of the components were made. The human ingestion bioaccessible fraction of As, Cd and Pb were determined using the in vitro BARGE UBM bioaccessibility test and were found to be 51.6%, 68.0% and 68.4% respectively. The relationship between the lability of the physico-chemical components and the bioaccessible fraction of the soils was investigated and the bioaccessible fractions were assigned to specific components. The extraction scheme using aqua regia was found to be the most suitable as it was the only one which extracted the iron sulphide phase in the soil.     

Determination of aliphatic amines in water by gas chromatography using headspace solvent microextraction

The possibility of applying headspace microextraction into a single drop for the determination of amines in aqueous solutions is demonstrated. A 1 μl drop of benzyl alcohol containing 2-butanone as an internal standard was suspended from the tip of a micro syringe needle over the headspace of stirred sample solutions for extraction. The drop was then injected directly into a GC. The total chromatographic determination was less than 10 min. Optimization of experimental conditions (sampling time, sampling temperature, stirring rate, ionic strength of the solution, concentration of reagents, time of extraction and organic drop volume) with respect to the extraction efficiency were investigated and the linear range and the precision were also examined. Calibration curves yielded good linearity and concentrations down to 2.5 ng ml⁻¹ were detectable with R.S.D. values ranging from 6.0 to 12.0%. Finally, the method was successfully applied to the extraction and determination of amines in tap and river water samples. This system represents an inexpensive, fast, simple and precise sample cleanup and preconcentration method for the determination of volatile organic compounds at trace levels.