A dispersive liquid-liquid microextraction procedure for determination of boron in water after ultrasound-assisted conversion to tetrafluoroborate

A novel, simple and green procedure is presented for the determination of boron. The method is based on ultrasound-assisted conversion of boron to tetrafluoroborate anion and the formation of an ion pair between BF₄⁻ and Astra Phloxine reagent (R), followed by dispersive liquid-liquid microextraction of the ion pair formed and subsequent UV-vis spectrophotometric detection. The conversion of boron to tetrafluoroborate anion is performed in an acidic medium of 0.9 mol L⁻¹ H₂SO₄ in the presence of 0.1 mol L⁻¹ F^- by means of 10 min of ultrasonication. The extraction of the ion pair formed between BF₄⁻ and R (1 × 10⁻⁴ mol L⁻¹ R) is carried out by dispersive liquid-liquid microextraction using 0.5 mL of amyl acetate (as extraction solvent), tetrachloromethane (as auxiliary solvent) and acetonitrile (as dispersive solvent) in a ratio of 1:1:2. The absorbance of the coloured extracts obeys Beer's law in the range 0.22-18.7 mg L⁻¹ of B(III) at 553 nm wavelength. The limit of detection calculated from a blank test (n = 10) based on 3 s is 0.015 mg L⁻¹ of B(III). The method was applied to the determination of boron in mineral waters.     

Part-per-trillion determination of chlorobenzenes in water using dispersive liquid-liquid microextraction combined gas chromatography-electron capture detection

In this study, a simple, rapid and efficient method, dispersive liquid-liquid microextraction (DLLME) combined gas chromatography-electron capture detection (GC-ECD), for the determination of chlorobenzenes (CBs) in water samples, has been described. This method involves the use of an appropriate mixture of extraction solvent (9.5 μl chlorobenzene) and disperser solvent (0.50 ml acetone) for the formation of cloudy solution in 5.00 ml aqueous sample containing analytes. After extraction, phase separation was performed by centrifugation and the enriched analytes in sedimented phase were determined by gas chromatography-electron capture detection (GC-ECD). Our simple conditions were conducted at room temperature with no stiring and no salt addition in order to minimize sample preparation steps. Parameters such as the kind and volume of extraction solvent, the kind and volume of disperser solvent, extraction time and salt effect, were studied and optimized. The method exhibited enrichment factors and recoveries ranging from 711 to 813 and 71.1 to 81.3%, respectively, within very short extraction time. The linearity of the method ranged from 0.05 to 100 μg l⁻¹ for dichlorobenzene isomers (DCB), 0.002-20 μg l⁻¹ for trichlorobenzene (TCB) and tetrachlorobenzene (TeCB) isomers and from 0.001 to 4 μg l⁻¹ for pentachlorobenzene (PeCB) and hexachlorobenzene (HCB). The limit of detection was in the low μg l⁻¹ level, ranging between 0.0005 and 0.05 μg l⁻¹. The relative standard deviations (R.S.D.s) for the concentration of DCB isomers, 5.00 μg l⁻¹, TCB and TeCB isomers, 0.500 μg l⁻¹, PeCB and HCB 0.100 μg l⁻¹ in water by using the internal standard were in the range of 0.52-2.8% (n = 5) and without the internal standard were in the range of 4.6-6.0% (n = 5). The relative recoveries of spiked CBs at different levels of chlorobenzene isomers in tap, well and river water samples were 109-121%, 105-113% and 87-120%, respectively. It is concluded that this method can be successfully applied for the determination of CBs in tap, river and well water samples.     

分散液相微萃取技术研究的最新进展

分散液相微萃取(DLLME)作为一种新型样品前处理技术,具有操作简便、快速,富集效率高,萃取剂使用量少等优点。本文对近年来该技术在分离科学领域应用的最新进展进行了简要评述。主要讨论了以下3个方面:(1)DLLME与其他净化或萃取技术的结合;(2)萃取剂的拓展;(3)萃取装置的改进。     

On-line sequential injection dispersive liquid-liquid microextraction system for flame atomic absorption spectrometric determination of copper and lead in water samples

A simple, sensitive and powerful on-line sequential injection (SI) dispersive liquid-liquid microextraction (DLLME) system was developed as an alternative approach for on-line metal preconcentration and separation, using extraction solvent at microlitre volume. The potentials of this novel schema, coupled to flame atomic absorption spectrometry (FAAS), were demonstrated for trace copper and lead determination in water samples. The stream of methanol (disperser solvent) containing 2.0% (v/v) xylene (extraction solvent) and 0.3% (m/v) ammonium diethyldithiophosphate (chelating agent) was merged on-line with the stream of sample (aqueous phase), resulting a cloudy mixture, which was consisted of fine droplets of the extraction solvent dispersed entirely into the aqueous phase. By this continuous process, metal chelating complexes were formed and extracted into the fine droplets of the extraction solvent. The hydrophobic droplets of organic phase were retained into a microcolumn packed with PTFE-turnings. A portion of 300 μL isobutylmethylketone was used for quantitative elution of the analytes, which transported directly to the nebulizer of FAAS. All the critical parameters of the system such as type of extraction solvent, flow-rate of disperser and sample, extraction time as well as the chemical parameters were studied. Under the optimum conditions the enhancement factor for copper and lead was 560 and 265, respectively. For copper, the detection limit and the precision (R.S.D.) were 0.04 μg L⁻¹ and 2.1% at 2.0 μg L⁻¹ Cu(II), respectively, while for lead were 0.54 μg L⁻¹ and 1.9% at 30.0 μg L⁻¹ Pb(II), respectively. The developed method was evaluated by analyzing certified reference material and applied successfully to the analysis of environmental water samples.     

Ligandless-dispersive liquid-liquid microextraction of trace amount of copper ions

In the present work, a new ligandless-dispersive liquid-liquid microextraction (LL-DLLME) method has been developed for preconcentration trace amounts of copper as a prior step to its determination by flame atomic absorption spectrometry. In the proposed approach 1,2-dicholorobenzene and ethanol were used as extraction and dispersive solvents, respectively. Some factors influencing on the extraction efficiency of copper and its subsequent determination were studied and optimized, such as the extraction and dispersive solvent type and volume, pH of sample solution, extraction time and salting out effect. Under the optimal conditions, the calibration curve was linear in the range of 1.0 ng mL⁻¹-0.6 μg mL⁻¹ of copper with R² = 0.9985. Detection limit was 0.5 ng mL⁻¹ in original solution (3S_b/m) and the relative standard deviation for seven replicate determination of 0.2 μg mL⁻¹ copper was ±1.4%. The proposed method has been applied for determination of copper in standard and water samples with satisfactory results.     

Speciation of mercury in water samples by dispersive liquid-liquid microextraction combined with high performance liquid chromatography-inductively coupled plasma mass spectrometry

The dispersive liquid-liquid microextraction (DLLME) combined with high performance liquid chromatography-inductively coupled plasma mass spectrometry for the speciation of mercury in water samples was described. Firstly methylmercury (MeHg⁺) and mercury (Hg²⁺) were complexed with sodium diethyldithiocarbamate, and then the complexes were extracted into carbon tetrachloride by using DLLME. Under the optimized conditions, the enrichment factors of 138 and 350 for MeHg⁺ and Hg²⁺ were obtained from only 5.00 mL sample solution. The detection limits of the analytes (as Hg) were 0.0076 ng mL⁻¹ for MeHg⁺ and 0.0014 ng mL⁻¹ for Hg²⁺, respectively. The relative standard deviations for ten replicate measurements of 0.5 ng mL⁻¹ MeHg⁺ and Hg²⁺ were 6.9% and 4.4%, respectively. Standard reference material of seawater (GBW(E)080042) was analyzed to verify the accuracy of the method and the results were in good agreement with the certified values. Finally, the developed method was successfully applied for the speciation of mercury in three environmental water samples.     

分散液液微萃取-反相液液微萃取-扫集-胶束电动色谱法测定红酒中的3种氯酚类物质

建立了分散液液微萃取（DLLME）-反相液液微萃取（RP-LLME）-扫集-胶束电动色谱富集模型,并用于红酒中五氯酚（PCP）、2,4,6-三氯酚（TCP）和2,4-二氯酚（DCP）3种氯酚的测定。实验考察了两步微萃取的萃取参数对氯酚萃取率的影响和样品分离富集的电泳条件。最佳萃取条件DLLME为：3.5 mL红酒（pH 3.0,120 g/L NaCl）,300 μL正己烷（萃取剂）;RP-LLME为：25 μL 0.16 mol/L NaOH（萃取剂）。最佳电泳条件：25 mmol/L NaH₂PO₄,100 mmol/L十二烷基硫酸钠（SDS）,30%（v/v）乙腈,pH 2.3;分离电压-15 kV;样品基质为80 mmol/L NaH₂PO₄;压力进样20 s×20.67 kPa（3 psi）。PCP和TCP的线性范围为0.5~100 μg/L（r≥0.9910）,DCP的线性范围为1.5~80 μg/L（r=0.9851）。3种分析物的检出限（S/N=3）为0.035~0.114 μg/L,加标回收率为75.2%~104.7%,相对标准偏差≤6.17%。该方法富集倍数高、灵敏度高、重现性好、分析速度快,可为不同样品基质中痕量氯酚污染物及某些弱酸性有机污染物测定提供参考。     

Ionic liquid based dispersive liquid-liquid microextraction of aromatic amines in water samples

In this work, a new microextraction method termed ionic liquid based dispersive liquid-liquid microextraction （IL-DLLME） was demonstrated for the extraction of 2-methylaniline, 4-chloroaniline, 1-naphthylamine and 4-aminobiphenyl in aqueous matrices. After extraction the ionic liquid （IL） phase was injected directly into the high performance liquid chromatography （HPLC） system for determination. Some parameters that might affect the extraction efficiency were optimized. Under the optimum conditions, good linear relationship, sensitivity and reproducibility were obtained. The limits of detection （LOD, S/N = 3） for the four analytes were in the range of 0.45-2.6 μg L^-1. The relative standard deviations （R.S.D., n = 6） were in the range of 6.2-9.8%. This method was applied for the analysis of the real water samples. The recoveries ranged from 93.4 to 106.4%. The main advantages of the method are high speed, high recovery, good repeatability and volatile organic solvent-free.     

A novel method for the determination of trace copper in cereals by dispersive liquid-liquid microextraction based on solidification of floating organic drop coupled with flame atomic absorption spectrometry

A novel,simple,rapid,efficient and environment-friendly method for the determination of trace copper in cereal samples was developed by using dispersive liquid-liquid microextraction based on solidification of floating organic drop(DLLME-SFO) followed by flame atomic absorption spectrometry.In the DLLME-SFO,copper was complexed with 8-hydroxy quinoline and extracted into a small volume of 1-dodecanol,which is of low density,low toxicity and proper melting point near room temperature. The experimental parameters affecting the extraction efficiency were investigated and optimized.Under the optimum conditions, the calibration graph exhibited linearity over the range of 0.5—500 ng/mL with the correlation coefficient(r) of 0.9996.The enrichment factor was 122 and the limit of detection was 0.1 ng/mL.The method was applied to the determination of copper in the complex matrix samples such as rice and millet with the recoveries for the spiked samples at 5.0 and 10.0 u,g/g falling in the range of 92.0-98.0%and the relative standard deviation of 3.9-5.7%.     

Recent trends in replacement of disperser solvent in dispersive liquid-liquid microextraction methods

Since its innovation in 2006, the dispersive liquid-liquid microextraction (DLLME) method has attracted the attention of analytical chemists in the field of sample preparation. This method has been successfully applied to determine trace amounts of pollutants in various matrices, but the restriction in the choice of suitable disperser and extraction solvents, and high disperser solvent consumption leading to decreased partition coefficients of the analytes between aqueous phase and extractant are its problems. To solve these drawbacks and develop environmentally friendly techniques, various alternatives for the conventional DLLME have been presented. The current review will begin with an introduction to the sample preparation, implementation of DLLME, and its advantages. Then, we focus on its drawbacks, which result mainly from the use of disperser solvent. Afterward, some of the most interesting approaches that have been employed and published until now are reviewed. Finally, an outlook on the future of these techniques will be given.     

A new device for magnetic stirring-assisted dispersive liquid-liquid microextraction of UV filters in environmental water samples

A new method based on dispersive liquid-liquid microextraction (DLLME) in combination with high-performance liquid chromatography (HPLC) has been developed for the analysis of UV filters. A specially designed flask, which has two narrow open necks with one of them having a capillary tip, was employed to facilitate the DLLME process. By adopting such a device, the extraction and subsequent phase separation were conveniently achieved. A binary solvent system of water sample and low-density extraction solvent (1-octanol) was used for the DLLME and no disperser solvent was involved. The extraction was accelerated by magnetic agitation of the two phases. After extraction, phase separation of the extraction solvent from the aqueous sample was easily achieved by leaving the extraction system statically for a while. No centrifugation step involving in classical DLLME was necessary. The analyte-enriched phase, floating above the sample solution, was elevated and concentrated into the narrow open tip of the flask by adding pure water into it via the other port, which was withdrawn with a microsyringe for the subsequent HPLC analysis. Under the optimized conditions, the limits of detection for the analytes were in range of 0.2-0.8 ng mL⁻¹ .The linearity ranges were 8-20,000 ng mL⁻¹ for HB, 7-20,000 ng mL⁻¹ for DB, 8-10,000 ng mL⁻¹ for BP and 5-20,000 ng mL⁻¹ for HMB, respectively. Enrichment factors ranging from 59 to 107 folders were obtained for the analytes. The relative standard deviations (n = 3) at a spiked level of 80 ng mL⁻¹ were between 1.4 and 4.8%. The proposed magnetic stirring-assisted DLLME method was successfully applied to the analysis of lake water samples.     

Dispersive liquid-liquid microextraction versus single-drop microextraction for the determination of several endocrine-disrupting phenols from seawaters

Two liquid-phase microextraction procedures: single-drop microextraction (SDME) and dispersive liquid-liquid microextraction (DLLME), have been developed for the determination of several endocrine-disrupting phenols (EDPs) in seawaters, in combination with high-performance liquid chromatography (HPLC) with UV detection. The EDPs studied were bisphenol-A, 4-cumylphenol, 4-tertbutylphenol, 4-octylphenol and 4-n-nonylphenol. The optimized SDME method used 2.5 μL of decanol suspended at the tip of a micro-syringe immersed in 5 mL of seawater sample, and 60 min for the extraction time. The performance of the SDME is characterized for average relative recoveries of 102 ± 11%, precision values (RSD) < 9.4% (spiked level of 50 ng mL⁻¹), and detection limits between 4 and 9 ng mL⁻¹. The optimized DLLME method used 150 μL of a mixture acetonitrile:decanol (ratio 15.7, v/v), which is quickly added to 5 mL of seawater sample, then subjected to vortex during 4 min and centrifuged at 2000 rpm for another 5 min. The performance of the DLLME is characterized for average relative recoveries of 98.7 ± 3.7%, precision values (RSD) < 7.2% (spiked level of 20 ng mL⁻¹), and detection limits between 0.2 and 1.6 ng mL⁻¹. The efficiencies of both methods have also been compared with spiked real seawater samples. The DLLME method has shown to be a more efficient approach for the determination of EDPs in seawater matrices, presenting enrichment factors ranging from 123 to 275, average relative recoveries of 110 ± 11%, and precision values (RSD) < 14%, when using a real seawaters (spiked level of 3.5 ng mL⁻¹).     

Recent developments in homogeneous and dispersive liquid-liquid extraction for inorganic elements determination. A review

This review aims to provide an overview of homogeneous liquid-liquid extraction (HLLE) and dispersive liquid-liquid microextraction (DLLME) methods and their potential use in inorganic analysis. Relevant applications to the determination of metal ions, metalloids and organometals are included. The phase separation mechanisms of these unconventional solvent extraction techniques are discussed. The new trends in the field of miniaturization and automation are presented, while proposing future trends and potential new areas for their application.     

A sensitive and selective method for determination of gold(III) based on electrothermal atomic absorption spectrometry in combination with dispersive liquid-liquid microextraction using dicyclohexylamine

A combined method with dispersive liquid-liquid microextraction (DLLME) and electrothermal atomic absorption spectrometry (ETAAS) has been developed for determining gold(III). Dicyclohexylamine, a new extractant for gold(III), showed excellent performance in DLLME. Acetone was indispensable to the quantitative extraction of gold(III), contributing to decrease in hydration, decrease in the difference in the dielectric constants between the supernatant phase and the sedimented phase, and dissolution of a part of chloroform as an extraction solvent to the supernatant phase as well as improvement of dipersibility. In DLLME using a mixture of 1.0 mL of acetone and 100 μL of chloroform containing 50 mmol L⁻¹ of dicyclohexylamine, gold(III) could be extracted selectively and effectively from 8 mL of a sample solution in the presence of iron(III), cobalt(II), nickel(II), copper(II), palladium(II), and platinum(IV) at pH 1. The extracted gold(III) was determinable by ETAAS; the detection limit was 0.002 μg L⁻¹ (three times the standard deviation of the blank values, n = 8) as a gold(III) concentration in 8 mL of sample solution. The proposed method was applicable to the determination of gold in platinum metal and its alloy as well as effluent without any interference by the matrices.     

分散液液微萃取技术及其在生物样品分析中的研究进展

分散液液微萃取是一种新型微萃取技术,具有易操作、低成本、耗时短、环境友好、萃取效率高等优点。该文着眼于分散液液微萃取技术中萃取剂的性质及辅助分散方式,综述了常规分散液液微萃取、离子液体分散液液微萃取、超声辅助分散液液微萃取等多种萃取模式,并重点归纳总结了近5年分散液液微萃取技术在生物样品分析领域的应用进展。     

Dispersive liquid-liquid microextraction followed by high-performance liquid chromatography as an efficient and sensitive technique for simultaneous determination of chloramphenicol and thiamphenicol in honey

Dispersive liquid-liquid microextraction (DLLME) coupled with high-performance liquid chromatography-variable wavelength detector (HPLC-VWD) was developed for extraction and determination of chloramphenicol (CAP) and thiamphenicol (THA) in honey. In this extraction method, 1.0 mL of acetonitrile (as dispersive solvent) containing 30 μL 1,1,2,2-tetrachloroethane (as extraction solution) was rapidly injected by syringe into a 5.00-mL water sample containing the analytes, thereby forming a cloudy solution. After extraction, phase separation was performed by centrifugation and the enriched analytes in the sedimented phase were determined by HPLC-VWD. Some important parameters, such as the nature and volume of extraction solvent and dispersive solvent, extraction time, sample solution pH, sample volume and salt effect were investigated and optimized. Under the optimum extraction condition, the method yields a linear calibration curve in the concentration range from 3 to 2000 μg kg⁻¹ for target analytes. The enrichment factors for CAP and THA were 68.2 and 87.9, and the limits of detection (S/N = 3) were 0.6 and 0.1 μg kg⁻¹, respectively. The relative standard deviations (RSDs) for the extraction of 10 μg kg⁻¹ of CAP and THA were 4.3% and 6.2% (n = 6). The main advantages of DLLME-HPLC method are simplicity of operation, rapidity, low cost, high enrichment factor, high recovery, good repeatability and extraction solvent volume at microliter level. Honey samples were successfully analyzed using the proposed method.     

Ligandless dispersive liquid-liquid microextraction for the separation of trace amounts of silver ions in water samples and flame atomic absorption spectrometry determination

In this article, a new ligandless dispersive liquid-liquid microextraction method has been developed for preconcentration of trace quantities of silver as a prior step to its determination by flame atomic absorption spectrometry. In the proposed approach, carbon tetrachloride and ethanol were used as extraction and dispersive solvents. Several factors that may be affected on the extraction process, like, extraction solvent, disperser solvent, the volume of extraction and disperser solvent, pH of the aqueous solution and extraction time were optimized. Under the optimal conditions, the calibration curve was linear in the range of 5.0 ng mL⁻¹ to 2.0 μg mL⁻¹ of silver with R² = 0.9995 (n = 9) and detection limit based on three times the standard deviation of the blank (3S_b) was 1.2 ng mL⁻¹ in original solution. The relative standard deviation for eight replicate determination of 0.5 μg mL⁻¹ silver was ±1.5%. The high efficiency of dispersive liquid-liquid microextraction to carry out the determination of silver in complex matrices was demonstrated. The proposed method has been applied for determination of trace amount of silver in standard and water samples with satisfactory results.     

超声辅助低密度溶剂分散液液微萃取-气相色谱-三重四极杆质谱法检测生物样品中的8种毒品

建立了生物样品中8种毒品的超声辅助分散液液微萃取-气相色谱-三重四极杆串联质谱检测方法,采用密度比水低的有机溶剂甲苯作为萃取溶剂,萃取过程中不需要任何分散剂。对影响萃取富集效率的因素进行优化:将100 μL甲苯萃取剂加入到1 mL样品溶液中,超声波剧烈振荡使甲苯充分分散到样品溶液中进行萃取,离心分层后,抽取上层萃取剂供气相色谱-三重四极杆串联质谱分析检测。在优化条件下,分析物在各自的线性范围内具有良好的线性关系,线性相关系数在0.9984~0.9994之间;检出限为0.05~0.40 μg/L (S/N=3);样品加标回收率在79.3%~100.3%之间,RSD<5.7%。本方法具有操作简单、灵敏度高和重现性好等优点,可应用于生物样品中多种毒品的分析检测。     

Application of dispersive liquid-liquid microextraction and high-performance liquid chromatography for the determination of three phthalate esters in water samples

A novel method, dispersive liquid-liquid microextraction (DLLME) coupled with high-performance liquid chromatography-variable wavelength detector (HPLC-VWD), has been developed for the determination of three phthalate esters (dimethyl phthalate (DMP), diethyl phthalate (DEP), and di-n-butyl phthalate (DnBP)) in water samples. A mixture of extraction solvent (41 μL carbon tetrachloride) and dispersive solvent (0.75 mL acetonitrile) were rapidly injected into 5.0 mL aqueous sample for the formation of cloudy solution, the analytes in the sample were extracted into the fine droplets of CCl₄. After extraction, phase separation was performed by centrifugation and the enriched analytes in the sedimented phase were determined by HPLC-VWD. Some important parameters, such as the kind and volume of extraction solvent and dispersive solvent, extraction time and salt effect were investigated and optimized. Under the optimum extraction condition, the method yields a linear calibration curve in the concentration range from 5 to 5000 ng mL⁻¹ for target analytes. The enrichment factors for DMP, DEP and DnBP were 45, 92 and 196, respectively, and the limits of detection were 1.8, 0.88 and 0.64 ng mL⁻¹, respectively. The relative standard deviations (R.S.D.) for the extraction of 10 ng mL⁻¹ of phthalate esters were in the range of 4.3-5.9% (n = 7). Lake water, tap water and bottled mineral water samples were successfully analyzed using the proposed method.     

Effervescence-assisted dispersive liquid-liquid microextraction based on deep eutectic solvent for preconcentration and FAAS determination of copper in aqueous samples

A new effervescence-assisted dispersive liquid-liquid microextraction, EA-DLLME, technique was developed for preconcentration and flame atomic absorption spectrometric determination of copper in aqueous samples. Effervescence assistance and DES combination for metal ion extraction was used for the first time. In the presented study, six different effervescence powders were examined to achieve maximum extraction efficiency. In addition, 1,5 diphenyl carbazide was used as complexing agent and DES prepared by mixing choline chloride and phenol was used as extraction solvent. The effect of several parameters such as pH, concentration of complexing agent, composition and volume of DES, amount of THF, composition and amount of effervescent agent were examined. Performed experiments showed that optimum pH was 6.0, the best effervesce powder composition was NaH₂PO₄:Na₂CO₃ with 2 × 10^?3:1 × 10^?3 molar ratio and the amount of effervesce powder was 0.4 g. Under optimum conditions enhancement factor, limit of detection and limit of quantification were calculated as 78, 2.9 and 9.7 μg L^?1, respectively. In addition, to prove precision of the method intra-day relative standard deviations were calculated for 10 and 50 μg L^?1 Cu²⁺ concentrations and found as 2.1% and 1.3%, respectively. The proposed method showed good linearity within the range of 10.0–100 μg L^?1. Finally, proposed method was successfully applied to determination of copper traces in aqueous samples.