Flow injection on-line electrothermal atomic absorption spectrometry

Today the greatest hindrances to couple the continuous FI system to discrete ETAAS operations have been overcome as demonstrated by the great number of papers published in the last few years. This paper reviews 109 references to the development and expansion of the FI-ETAAS methodology. The selected FI-ETAAS systems, namely: on-line column preconcentration and separation systems; on-line knotted reactor preconcentration systems; on-line aerosol deposition systems; flow-injection for in situ trapping of volatile compounds and miscellaneous on-line systems.     

Simultaneous determination of palladium and rhodium using on-line column enrichment and electrothermal atomic absorption spectrometric detection

Flow injection on-line micro-column pre-concentration was coupled with electrothermal atomic absorption spectrometry (ETAAS) for the simultaneous determination of Rh and Pd in environmental samples. The micro-column contained 1,5-Bis(2-pyridyl)-3-sulphophenyl methylene thiocarbonohydrazide (PSTH) immobilised on an anion-exchange resin (Dowex 1 × 8–200). The sorbent was tested in a micro-column, placed in the auto-sampler arm, at the flow rate 3.1 mL/min. Elution was performed with 2 M HNO₃ and the system was optimised with a 60 s pre-concentration time.     

Solid sampling electrothermal atomic absorption spectrometry for analysis of high-purity tungsten trioxide and high-purity tungsten blue oxide

A solid sampling ETAAS method for the direct determination of Ca, Co, Cr, Cu, Fe, K, Mg, Mn, Na, Ni and Zn in high-purity tungsten trioxide and tungsten blue oxide powders using a modern spectrometer with transversely heated graphite tube and a solid sampling system is described. The extremely high background caused by the vaporizing tungsten oxides could be eliminated by the reduction to tungsten metal using hydrogen as purge gas during pyrolysis. Quantification of all elements was performed using calibration curves measured with aqueous standard solutions. The analyte contents determined were between 0.033 (Cu) and 12.6 (Fe) μg/g for tungsten trioxide and between 0.001 (Co) and 0.5 (Na) μg/g for tungsten blue oxide. The accuracy was checked by comparing the results with those obtained by ETAAS in analysis of HF/HNO₃ sample digests and by other methods. Extremely low limits of detection being between 0.07 (Mg, Na, Zn) - 2 (Ni) and 0.01 (Mg, Na, Ni) - 1.7 (Fe) ng/g for tungsten trioxide and tungsten blue oxide, respectively, could be achieved due to almost complete freedom of blank and unusually high applicable sample amounts (5–15 mg for tungsten trioxide and 5–70 mg for tungsten blue oxide).     

Direct solid sampling electrothermal atomic absorption spectrometry for the analysis of high-purity niobium pentaoxide

A direct solid sampling electrothermal atomic absorption spectrometry (SoS-ETAAS) method for ultratrace analysis of powdered niobium pentaoxide for Al, Co, Cr, Cu, Fe, K, Mg, Mn, Na, Ni and Zn has been developed. The elements K, Mg, Na and Zn could be determined without any chemical modification. However, in the determination of the elements Al, Co, Cr, Cu, Fe, Mn and Ni, serious matrix-caused non-spectral interferences and background occurred which made their determination impossible. This problem was remedied by conversion of the niobium pentaoxide matrix into the thermally stable niobium carbide by using methane atmosphere during the pyrolysis stage. The development resulted in establishing an extraordinary powerful method for the analysis of niobium pentaoxide in term of limits of detection, accuracy, simplicity and analysis time. Quantification was performed using calibration curves measured with aqueous standard solutions. The accuracy was checked by comparing the results with those obtained by ETAAS in analysis of slurries and digests of the sample. Due to almost complete freedom of blank and high applicable sample amounts (up to 15 mg), extremely low limits of detection (0.5-2 ng/g) were achieved.     

Slurry sampling electrothermal atomic absorption spectrometry for trace element analysis of high-purity tungsten trioxide

A slurry sampling ETAAS method for the determination of trace concentrations of Ca, Co, Cr, Cu, Fe, K, Mg, Na and Ni in tungsten trioxide is presented. A high background absorption appearing with large sample amounts during atomization at high temperatures was the only matrix interference observed. It could be significantly reduced by volatilization of the matrix in the pyrolysis step. Calibration curves recorded with aqueous standards could be used for calibration in all cases excluding the determination of very low analyte concentrations of Co and Fe which required the use of the standard additions method. The results obtained by this method showed an excellent agreement with those determined in digests by ETAAS. The detection limits achievable by the slurry technique were between 1 (Ca, K, Mg, Na) and 210 (Cu) ng/g. They were mostly by more than one order of magnitude better than those of the solution techniques.     

Direct solid sampling electrothermal atomic absorption spectrometry for the analysis of high-purity niobium pentaoxide

A direct solid sampling electrothermal atomic absorption spectrometry (SoS-ETAAS) method for ultratrace analysis of powdered niobium pentaoxide for Al, Co, Cr, Cu, Fe, K, Mg, Mn, Na, Ni and Zn has been developed. The elements K, Mg, Na and Zn could be determined without any chemical modification. However, in the determination of the elements Al, Co, Cr, Cu, Fe, Mn and Ni, serious matrix-caused non-spectral interferences and background occurred which made their determination impossible. This problem was remedied by conversion of the niobium pentaoxide matrix into the thermally stable niobium carbide by using methane atmosphere during the pyrolysis stage. The development resulted in establishing an extraordinary powerful method for the analysis of niobium pentaoxide in term of limits of detection, accuracy, simplicity and analysis time. Quantification was performed using calibration curves measured with aqueous standard solutions. The accuracy was checked by comparing the results with those obtained by ETAAS in analysis of slurries and digests of the sample. Due to almost complete freedom of blank and high applicable sample amounts (up to 15 mg), extremely low limits of detection (0.5–2 ng/g) were achieved.     

Slurry sampling electrothermal atomic absorption spectrometry for trace element analysis of high-purity tungsten trioxide

A slurry sampling ETAAS method for the determination of trace concentrations of Ca, Co, Cr, Cu, Fe, K, Mg, Na and Ni in tungsten trioxide is presented. A high background absorption appearing with large sample amounts during atomization at high temperatures was the only matrix interference observed. It could be significantly reduced by volatilization of the matrix in the pyrolysis step. Calibration curves recorded with aqueous standards could be used for calibration in all cases excluding the determination of very low analyte concentrations of Co and Fe which required the use of the standard additions method. The results obtained by this method showed an excellent agreement with those determined in digests by ETAAS. The detection limits achievable by the slurry technique were between 1 (Ca, K, Mg, Na) and 210 (Cu) ng/g. They were mostly by more than one order of magnitude better than those of the solution techniques. Received: 9 July 1997 / Revised: 6 October 1997 / Accepted: 10 October 1997     

Determination of As,Sb and Bi in high-purity copper by electrothermal atomic absorption spectrometry

As, Sb and Bi were determined in copper electric cables by atomic absorption spectrometry with electrothermal atomization in a graphite furnace. The interferences in the determination of As, Sb and Bi caused by eleven cationic species and six types of acid were studied. The different volatilization of the copper matrix in comparison to the analyte was studied, as a means of increasing the analyte signal/non-specific absorption signal ratio.     

Literature study of microwave-assisted digestion using electrothermal atomic absorption spectrometry

The literature on the use of microwave-assisted digestion procedures for subsequent sample analysis by means of electrothermal atomic absorption spectrometry (ETAAS) is reviewed. The literature survey reveals that this digestion technique has been applied mainly for biological materials. The elements most extensively determined by this method are cadmium and lead followed by copper, chromium, nickel and iron. The microwave digestion conditions, ETAAS furnace programmes and analytical details of the developed methodologies have been carefully revised.     

Literature study of microwave-assisted digestion using electrothermal atomic absorption spectrometry

The literature on the use of microwave-assisted digestion procedures for subsequent sample analysis by means of electrothermal atomic absorption spectrometry (ETAAS) is reviewed. The literature survey reveals that this digestion technique has been applied mainly for biological materials. The elements most extensively determined by this method are cadmium and lead followed by copper, chromium, nickel and iron. The microwave digestion conditions, ETAAS furnace programmes and analytical details of the developed methodologies have been carefully revised.     

Possibilities of inductively coupled plasma atomic emission spectrometry with electrothermal vaporization in the analysis of high-purity reagents

Possibilities of electrothermal sample vaporization in inductively coupled plasma atomic emission spectrometry (ETV-ICP-AES) in the analysis of high-purity reagents were studied on an example high-purity waters, acid solutions, and trace impurity concentrates. The analytical and background signals in the injection of solutions into inductively coupled plasma (ICP) by pneumatic nebulization and electrothermal vaporization were compared and the of limits of detection in the analysis of high-purity reagents with impurity preconcentration by evaporation were estimated and compared.     

Application of flow injection on-line electrothermal atomic absorption spectrometry to the determination of rhodium

A fully automated procedure for the determination of rhodium has been developed using flow injection (FI) on-line microcolumn preconcentration coupled with electrothermal atomic absorption spectrometry (ETAAS). The proposed FI manifold and its operation make possible the introduction of the total eluate volume into the graphite atomizer, avoiding the necessity for optimisation of subsampling the eluate. Rhodium is adsorbed on a microcolumn packed with 1,5-bis(di-2-pyridyl)methylene thiocarbohydrazide immobilized on silica gel (DPTH-gel). Under the optimum conditions, using a 60 s preconcentration time, a sample flow rate of 3.5 mL min(-1) and an injection volume of eluent of 50 microL, a linear calibration graph was obtained from 1 to at least 40 ng mL(-1) and the detection limit was 1 ng mL(-1). The proposed method has been successfully applied to the analysis of samples. Its performance was investigated against certified reference catalyst sample SRM-2557 and by recovery measurements on spiked samples (soil, foods and beverages).     

Evaluation of on-line coupling size exclusion chromatography electrothermal atomic absorption spectrometry for selenium speciation

 Chromatographic effluents were on-line analyzed by Zeeman-ETAAS, using a flow-through cell placed in a graphite furnace autosampler as interface. To obtain high sampling rates, the use of fast graphite furnace programmes was studied. Conventional programmes of 96 s were reduced to 18 s by using hot injection (120 °C) and reducing the charring step to 2 s. The increase of the injection volume from 20 to 60 μl lengthened the programme to 46 s. Nickel had to be added to get a comparable response for both inorganic and organic selenium species (selenite and selenomethionine) and to reduce the interferent effect produced in presence of the chromatographic eluent (TRIS 0.01 mol l^-1, NH₄NO₃ 0.1 mol l^-1, pH 7). The optimized conditions were applied to the speciation of selenium in human erythrocyte lysates by size exclusion LC-ETAAS. Using a high performance size exclusion column selenium could be assigned to proteins of 100 and 35 kDa. Detection limits in the range of 1 ng (2 μg l^-1 for 500 μl injection volume) were obtained for the combined technique. Received: 9 October 1996/Revised: 8 July 1996/Accepted: 14 July 1996     

Analysis of cobalt in plasma by electrothermal atomic absorption spectrometry

Summary A method for the determination of traces of cobalt in plasma is described. The sample is digested in a test tube using a mixture of nitric and perchloric acid. Ammonium-pyrrolidine dithiocarbamate is added as chelating agent, and after pH-adjustment to pH 9±0.1, cobalt is extracted into methyl-isobutyl ketone.Recovery studies using Co-60 showed that losses of cobalt during the procedure, including digestion and extraction are less than 3%. Possible contamination from the steel needle used is tested and discussed. The coefficient of variation for the method is 9.5% at the 0.20 g/l level. A realistic determination limit following this procedure is estimated to be 0.06 g/l. Using this method, the cobalt concentration in plasma from 32 control persons was determined to 0.15 ±0.07 g/l. For 10 refinery workers daily exposed to aerosols of CoCl₂ the determined average was 9.7±7.1 g/l.

---

Analyse von Kobalt in Plasma mit Hilfe der elektrothermischen AAS

Zusammenfassung Bei dem beschriebenen Verfahren wird die Probe mit Hilfe von Salpetersäure/Perchlorsäure aufgeschlossen. Als Komplexierungs-Reagens wird Ammonium-pyrrolidindithiocarbamat zugefügt und nach pH-Einstellung auf 9±0,1 wird Co mit Methylisobutylketon extrahiert.Mit Hilfe von Co-60 wurde festgestellt, daß die durch Aufschluß und Extraktion verursachten Verluste weniger als 3% betragen. Eine mögliche Verunreinigung durch die benutzten Stahlnadeln wurde untersucht und diskutiert. Der Variationskoeffizient beträgt 9,5% bei 0,2 g Co/l. Die Bestimmungsgrenze nach diesem Verfahren liegt bei 0,06 g Co/l. Die Kobaltkonzentration im Plasma von 32 Kontrollpersonen wurde zu 0,15±0,07 g Co/l bestimmt. Für 10 Raffineriearbeiter, die täglich CoCl₂-Aerosolen ausgesetzt waren, wurde ein Durchschnitt von 9,7±7,1 g Co/l gefunden.

     

Tube-probe atomisation in electrothermal atomic absorption spectrometry

A method is described in which liquid samples are deposited by a conventional autosampler on to a tubular graphite probe positioned inside a 7.5 mm i.d. Pye Unicam SP-9 atomiser cuvette. The tube-probe has certain advantages in comparison with the flat probe systems described previously. In particular, the precision of determinations in acid media is improved since the sample solution is better confined within the atomiser and hence the effects of droplet spreading are curtailed. Also, the tube-probe is shown to reduce diffusional loss effects at high atomiser temperatures, in comparison with flat probe operation. The characteristic mass values obtained for volatile and medium volatile elements are similar for tube and flat probes. Since a greater sample volume (up to 40 μl) can be deposited and dried in the tube-probe, improved detection limits are anticipated for these elements. For more involatile elements, the greater mass of the tube-probe results in poorer sensitivity by a factor of × 3 for V and × 4 for Cr.     

Trends and potentials in flow injection on-line separation and preconcentration techniques for electrothermal atomic absorption spectrometry

Recent progress in flow injection on-line separation and preconcentration techniques for electrothermal atomic absorption spectrometry (ETAAS) are reviewed, stressing the advancements made within the past 2 or 3 years. Important trends and potentials for future development are discussed, including the use of air-transport and air-segmentation in on-line separation systems, the use of knotted reactors as a sorption medium, and other designs for on-line coprecipitation and solvent extraction systems to improve the robustness and efficiency of on-line separation systems for ETAAS.     

Trace metal enrichment by automated on-line column preconcentration for flow-injection atomic absorption spectrometry

An on-line column preconcentration technique for flow-injection atomic absorption spectrometry was developed. Diverse metal ions (Cd²⁺, Zn²⁺, Cu²⁺, Mn²⁺, Pb²⁺, Fe³⁺ and Cr³⁺) in solution were concentrated quantitatively by a microcolumn (7-mm × 4-mm i.d.) packed with Muromac A-1, which is an iminodiacetate chelate resin, in a flow-injection system. From the pH dependence of the uptake of the ions, all the divalent metals examined were recovered quantitatively in the pH range 3–5 and the trivalent metals were recovered at a maximum pH of 1. Enrichment factors using 20-ml samples were in the range 90–180-fold for the seven elements and the sampling rate was 13 h^?1. The 3σ detection limits were in the range 0.14–2.1 μg l^?1 and the relative standard deviations for replicate measurements (n=3–4) were in the range 0.7–1.7%. The method was compared with flame and graphite furnace atomic absorption spectrometry. Application to the determination of cadmium and copper in several standard reference materials is described.     

Investigation of phosphorus atomization using high-resolution continuum source electrothermal atomic absorption spectrometry

The atomization of phosphorus in electrothermal atomic absorption spectrometry has been investigated using a high-resolution continuum source atomic absorption spectrometer and atomization from a graphite platform as well as from a tantalum boat inserted in a graphite tube. A two-step atomization mechanism is proposed for phosphorus, where the first step is a thermal dissociation, resulting in a fast atomization signal early in the atomization stage, and the second step is a slow release of phosphorus atoms from the graphite tube surface following the adsorption of molecular phosphorus at active sites of the graphite surface. Depending on experimental conditions only one of the mechanisms or both might be active. In the absence of a modifier and with atomization from a graphite or tantalum platform the second mechanism appears to be dominant, whereas in the presence of sodium fluoride as a modifier both mechanisms are observed. Intercalation of phosphorus into the graphite platform in the condensed phase has also been observed; this phosphorus, however, appears to be permanently trapped in the structure of the graphite and does not contribute to the absorption signal.     

Glassy carbon tubes for electrothermal atomic absorption spectrometry

Summary The use of glassy carbon as a tube material in electrothermal atomic absorption spectrometry requires modifications to the power supply if temperatures and heating rates comparable to those for graphite tubes are to be obtained. Glassy carbon tubes frequently have a longer lifetime than pyrolytic graphite coated tubes made of polycrystalline electrographite. Peak height sensitivity for glassy carbon is better by a factor of two for some volatile elements, but up to a factor of five inferior for less volatile elements than that for pyrolytic graphite coated tubes. Peak area sensitivity is generally inferior by about a factor of two. Sample volume is limited to 5–10 l because of the smooth surface.From the signal shape it can be deduced that adsorption of analyte atoms at the tube wall plays an important role in glassy carbon, and is responsible at least in part for the lower sensitivity. Non-spectral interferences can be less pronounced in glassy carbon tubes for those interferents which interact with graphite tube surfaces. Glassy carbon is, however, no alternative to pyrolytic graphite coated tubes.

---

Glasartiger Kohlenstoff als Rohrmaterial für elektrothermische Atomabsorptionsspektrometrie

     

Plasma afterglow atomization in electrothermal atomic absorption spectrometry

Potentialities of an Ar/H₂ microwave induced plasma afterglow at 8.2 mbar as an atomization source in electrothermal atomic absorption spectrometry have been examined. More specifically the atomization efficiency, as shown from appearance temperatures, and the reaction mechanisms of the atomization of the oxides and chlorides of alkaline earth and transition metals have been investigated and compared with conventional electrothermal atomization. For all the investigated metal chlorides and alkaline earth oxides, a considerable decrease in appearance temperature (some 500 K), is observed in the plasma afterglow. Such enhanced atomization is believed to be linked to reactions with H atoms. No plasma enhancement, however, is measured for the atomization of the transition metal oxides. All metal oxides are effectively reduced to free metal in the solid state by the Ar/H₂ afterglow, and as a consequence the supply rate is governed by the metal sublimation for these compounds. For metal chlorides, however, strong evidence is found for the atomization process to proceed via gas phase reactions.