Characterization of Branched Poly (vinyl Acetate) by GPC and Low Angle Laser Light Scattering Photometry

Abstract

Poly (vinyl acetate), PVAC, synthesized by bulk polymerization over a range of initiator concentrations ([AIBN] = 10^?5 to 4 × 10^?3 g-mole/1), temperatures (50°C, 60°C, 70°C, and 80°C) and conversion levels (3 to > 90%) were characterized using low angle laser light scattering (LALLS) photometry to measure M_w of the whole polymers. A number of these samples were characterized using GPC with a differential refractive index (DRI) and LALLS detector to measure the molecular weight distribution (weight fraction versus M_w). M_w for PVAC samples synthesized at suitably low initiator levels at various conversions were found to agree with classical light scattering measurements after Graessley.

An electronic device and a technique which optimizes the sensitivity and the signal-to-noise ratio of the LALLS photometer throughout the molecular weight distribution (MWD) of the GPC chromatogram were devised. These considerably simplify the operation of the LALLS for both offline and online operation with GPC.

Most importantly it was unambiguously shown that the commonly used universal calibration parameter (UCP) with GPC, [n]M_w, is incorrect for polymers with molecules having the same hydrodynamic volume but different molecular weights, i. e., those with only chain branching (LCB), copolymers with compositional drift, and polymer blends. The correct UCP was found to     

Star poly(methyl methacrylate) with end‐functionalized arm chains by ruthenium‐catalyzed living radical polymerization

Star polymers with end‐functionalized arm chains (surface‐functionalized star polymers) were synthesized by the in situ linking reaction between ethylene glycol dimethacrylate (linking agent) and an α‐end‐functionalized linear living poly(methyl methacrylate) in RuCl₂(PPh₃)₃‐catalyzed living radical polymerization; the terminal on the surface functionalities included amides, alcohols, amines, and esters. The star polymers were obtained in high yields (75–90%) with initiating systems consisting of a functionalized 2‐chloro‐2‐phenylacetate or ‐acetamide [F? C(O)CHPhCl; F = nPrNH? , HOCH₂CH₂O? , Me₂NCH₂CH₂O? , or EtO? ; initiator] and n‐Bu₃N (additive). The yield was lower with a functionalized 2‐bromoisobutyrate [Me₂NCH₂CH₂OC(O)CMe₂Br] initiator or with Al(Oi‐Pr)₃ as an additive. Multi‐angle laser light scattering analysis showed that the star polymers had arm numbers of 10–100, radii of gyration of 6–23 nm, and weight‐average molecular weights of 1.3 × 10⁵ to 3.0 × 10⁶, which could be controlled by the molar ratio of the linking agent to the linear living polymers. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1972–1982, 2002     

SYNTHESIS AND CHARACTERIZATION OF FOUR-ARMED BLOCK POLY(STYRENE-b-p-NITROPHENYL METHACRYLATE)PREPARED BY THE ATRP METHOD*

A novel tetrafunctional initiator, C [CH_2O (CH_2)_3 OOCCH(Br)CH_3]_4 (1), was synthesized through the reaction oftetraol with α-bromopropionyl chloride, and then was used as initiator of atom transfer radical polymerization (ATRP) in thepreparation of 4-armed polystyrene (PSt) with narrow polydispersity. The structure, molecular weight and molecular weightdistribution (MWD) of each arm were studied by ~1H-NMR and GPC data of hydrolyzed products of the 4-armed PSt. TheATRP of St using 1/CuBr/bpy as initiator system is of "living" character based on the following evidence: narrow MWD,constant concentration of chain radical during the polymerization, control of molecular weight by the molar ratio of monomerconsumed to 1. The 4-armed poly(St-b-p-nitrophenyl methacrylate) [poly(St-b-NPMA)] was prepared by the ATRP ofNPMA using 4-armed PSt with terminal bromine as the initiator, and characterized by FT-IR, ~1H-NMR spectra and GPCcurves. The micelles with PSt as core, and PNPMA as shell were formed by dropping DMSO into a solution of 4-armedpoly(St-b-NPMA) in DMF, as proved by laser light scatter (LLS) method.     

Controlled cationic polymerization of cyclopentadiene with B(C6F5)3 as a coinitiator in the presence of water

The controlled cationic polymerization of cyclopentadiene (CPD) at 20 °C using 1‐(4‐methoxyphenyl)ethanol (1)/B(C₆F₅)₃ initiating system in the presence of fairly large amount of water is reported. The number–average molecular weights of the obtained polymers increased in direct proportion to monomer conversion in agreement with calculated values and were inversely proportional to initiator concentration, while the molecular weight distribution slightly broadened during the polymerization (M_w/M_n ～ 1.15–1.60). ¹H NMR analyses confirmed that the polymerization proceeds via reversible activation of the C? OH bond derived from the initiator to generate the growing cationic species, although some loss of hydroxyl functionality happened in the course of the polymerization. It was also shown that the enchainment in cationic polymerization of CPD was affected by the nature of the solvent(s): for instance, polymers with high regioselectivity ([1,4] up to 70%) were obtained in acetonitrile, whereas lower values (around 60%) were found in CH₂Cl₂/CH₃CN mixtures. Aqueous suspension polymerization of CPD using the same initiating system was successfully performed and allowed to synthesize primarily hydroxyl‐terminated oligomers (F_n = 0.8–0.9) with M_n ≤ 1000 g mol^?1 and broad MWD (M_w/M_n ～ 2.2). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4734–4747, 2008     

Synthesis and Characterization of Organosoluble Poly(imide-ether)s with Bulky 2,3-Diaryl Imidazole Moiety: Study Physical,Thermal and Optical Properties

Two new symmetrical diamines were designed and synthesized having different functional groups such as a pair of phenyl ether linkages, 2,3-diaryl substituted imidazole rings and CF₃ groups as pendant, and characterized by FT-IR, ¹H and ¹³C-NMR spectroscopy and elemental analysis. A series of new fluorescent poly(imide-ether)s (PIEs) was prepared by polymerization of the diamines with commercial tetracarboxylic dianhydrides such as pyromellitic dianhydride and 3,3′,4,4′-benzophenone tetracarboxylic dianhydride. The resulting PIEs were amorphous and had intrinsic viscosity [η] in the range of 0.42–0.51 dL/g. The weight average molecular weights (Mw) of these polymers were measured by GPC and were in the range of 28658–35595 g/mol with molecular weight distribution (MWD) of 2.12–2.27. These polymers were readily soluble in a variety of organic solvents and formed low-colored and flexible thin films with cut-off wavelength (λ₀) in the range of 385–420 nm, and all PIEs films exhibited high optical transparency. They also possessed good thermal stability with 10% weight loss temperatures (T_10%) in the range 486–537°C in N₂. The glass transition temperatures (T_g) of PIEs are in the range 251–324°C. These polymers showed fluorescence emission in film and in solution at 459–476 nm with the quantum yields in the range 4–12%.     

UHMWPE with short‐chain branches synthesized by alkenyl substituted phenoxy–imine catalysts in ethylene polymerization

The alkenyl substituted phenoxy–imine complexes [2‐C₃H₅‐6‐(2, 3, 5, 6‐C₆F₄H‐N?CH)C₆H₃O]₂TiCl₂ (C₃H₅=? CH₂? CH?CH₂ or ? CH?CH? CH₃) are synthesized and characterized by ¹H NMR, ¹³C NMR, and elemental analysis. When activated by MAO, they show high activity for the polymerization of ethylene to UHMWPE under different conditions (temperatures and polymerization time). Most of the resulting polymers have high molecular weights (>1.0 × 10⁶ g·mol^?1) and high melting points as well as crystallinity. To clarify the effect of the alkenyl group on the catalytic performance and the resultant polymer microstructure, the corresponding saturated complexes of type [2‐C₃H₇?6‐(2, 3, 5, 6‐C₆F₄H‐N?CH)C₆H₃O]₂TiCl₂ where C₃H₇ = –CH₂? CH₂? CH₃ or ? CH(CH₃)₂ were synthesized and tested as catalysts in ethylene polymerization under the same reaction conditions. The microstructure and morphologies of these two species of PE samples were fully compared by the analysis of ¹³C NMR, GPC, DSC, and SEM. As a result, the allyl substituted complex show the highest activity to prepare the highest molecular weight polyethylene of all the catalysts. An interesting feature of the UHMWPE produced by these four catalysts is that they contain only a few short‐chain branches (mainly methyl, isobutyl and 2‐methylhexyl branches) in a low amount (<2.7 branches/1000 C). © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3808–3818     

(Diisopropylamido) bis (methylcyclopentadienyl) lanthanides as single-component initiators for polymerization of methyl methacrylate

It was first found that (diisopropylamido)bis(methylcyclopentadienyl)lanthanides (MeC₅H₄)₂LnN(i-Pr)₂(THF) (Ln = Yb ( 1 ), Er ( 2 ), Y ( 3 )) exhibit extremely high catalytic activity in the polymerization of methyl methacrylate. The reactions can be carried out over a quite broad range of polymerization temperatures from -78 to 40°C. The catalytic activity of the complexes increases with an increase of ionic radii of the metal elements, i.e. Y > Er > Yb. The results of GPC (gel permeation chromatography) indicate that the number-average molecular weights (M_n) of polymers obtained exceed 100 × 10³ and the molecular weight distribution (M_w/M_n) becomes broad with the increase of temperature. Furthermore highly syndiotactic PMMA (87.7%) can be obtained by lowering the reaction temperature to −78°C. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1593–1597, 1998     

Solution characterization of the novel organometallic polymer poly(ferrocenyldimethylsilane)

A series of four well‐defined poly(ferrocenyldimethylsilane) (PFS) samples spanning a molecular weight range of approximately 10,000–100,000 g mol⁻¹ was synthesized by the living anionic polymerization of dimethyl[1]silaferrocenophane initiated with n‐BuLi. The polymers possessed narrow polydispersities and were used to characterize the solution behavior of PFS in tetrahydrofuran (THF). The weight‐average molecular weights (M_w ) of the polymers were determined by low‐angle laser light scattering (LALLS), conventional gel permeation chromatography (GPC), and GPC equipped with a triple detector (refractive index, light scattering, and viscosity). The molecular weight calculated by conventional GPC, with polystyrene standards, underestimated the true value in comparison with LALLS and GPC with the triple detection system. The Mark–Houwink parameter a for PFS in THF was 0.62 (k = 2.5 × 10⁻⁴), which is indicative of fairly marginal polymer–solvent interactions. The scaling exponent between the radius of gyration and M_w was 0.54, also consistent with marginal polymer–solvent interactions for PFS in THF. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 3032–3041, 2000     

Metal-complex-bearing star polymers by metal-catalyzed living radical polymerization: Synthesis and characterization of poly(methyl methacrylate) star polymers with Ru(II)-embedded microgel cores

One-pot, spontaneous, and in-situ incorporation of Ru(II) complexes into a microgel (solubilized nanometer-scale network) has been achieved in near quantitative efficiency by a polymer-linking reaction of linear living poly(methyl methacrylate) (PMMA) with a bifunctional methacrylate (ethylene glycol dimethacrylate or bisphenol A dimethacrylate; linking agent) and a phosphine-ligand monomer [diphenyl-4-styryl-phosphine ( 3 ); i.e., CH₂CH C₆H₄ p-PPh₂] in the RuCl₂(PPh₃)₃-catalyzed living radical polymerization. The products were Ru-bearing. PMMA-armed star polymers with a microgel-core that consisted of a copolymer network of the linking agent and 3 . Upon the network formation, the phosphine ligands efficiently encapsulated RuCl₂(PPh₃)₃, thus achieving a polymer catalyst directly from a polymerization catalyst. Colored dark brown-red, the star polymers exhibited UV-vis absorptions originating from the entrapped complex (3.1–7.4 × 10⁻⁵ mol Ru/g of polymer), the incorporation efficiency being close to 100% with respect to the original polymerization-catalyst. Detailed spectroscopic characterization showed the following: an absolute molecular weight of 1.7 × 10⁵ to 1.7 × 10⁶, an arm number of 11–92 arms/polymer, and a radius of gyration of 8–19 nm (in DMF). Direct observation of the individual star molecules in solid state was achieved by transmission electron microscopy (unstained; 2–3 nm dark dots for the core) and atomic force microscopy (semi-circular images). © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4966–4980, 2006     

Addition polymerization of norbornene using bis(β‐ketoamino)nickel(II)/tris(pentafluorophenyl)borane catalytic systems

Norbornene polymerizations proceeded in toluene with bis(β‐ketoamino)nickel(II) {Ni[CH₃C(O)CHC(NR)CH₃]₂ [R = phenyl ( 1 ) or naphthyl ( 2 )]} complexes as the catalyst precursors and the organo‐Lewis compound tris(pentafluorophenyl)borane [B(C₆F₅)₃] as a unique cocatalyst. The polymerization conditions, such as the cocatalyst/catalyst ratio (B/Ni), catalyst concentration, monomer/catalyst ratio (norbornene/Ni), polymerization temperature, and polymerization time, were studied in detail. Both bis(β‐ketoamino)nickel(II)/B(C₆F₅)₃ catalytic systems showed noticeably high conversions and activities. The polymerization activities were up to 3.64 × 10⁷ g of polymer/mol of Ni h for complex 1 /(B(C₆F₅)₃ and 3.80 × 10⁷ g of polymer/mol of Ni h for complex 2 /B(C₆F₅)₃, and very high conversions of 90–95% were maintained; both polymerizations provided high‐molecular‐weight polynorbornenes with molecular weight distributions (weight‐average molecular weight/number‐average molecular weight) of 2.5–3.0. The achieved polynorbornenes were confirmed to be vinyl‐addition and atactic polymers through the analysis of Fourier transform infrared, ¹H NMR, and ¹³C NMR spectra, and the thermogravimetric analysis results showed that the polynorbornenes exhibited good thermal stability (decomposition temperature > 410 °C). © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4733–4743, 2007     

Preparation of ultra high molecular weight amorphous poly(1‐hexene) by a Ziegler–Natta catalyst

High molecular weight polymers such as poly (α‐olefin)s play a key role as drag‐reducing agents which are commonly used in pipeline industry. Heterogeneous Ziegler–Natta catalyst system of MgCl₂.nEtOH/TiCl₄/donor was prepared using a spherical MgCl₂ support and utilized in synthesis of poly(1‐hexene)s with a viscosity average molecular weight (M_v) up to 3.5 × 10³ kDa. The influence of effective parameters including Al/Ti ratio, polymerization temperature, monomer concentration, effect of alkylaluminus type on the productivity, and molecular weight of the products was evaluated. It was suggested that the reactivity of the Al‐R group and the bulkiness of the cocatalyst were correlated to the performance of the Ziegler–Natta catalyst at different polymerization time and temperatures, affecting the catalyst activity and M_v of polymers. Moreover, bulk polymerization method leads to higher viscosity average molecular weights, revealing the remarkable effect of polymerization method on the chain microstructure. Fourier transform infrared, ¹³C Nuclear magnetic resonance spectra, and DSC thermogram of the prepared polymers confirmed the formation of poly(1‐hexene). The properties of the polymers measured by vortex test showed that these polymers could be used as a drag‐reducing agent. Drag‐reducing behaviors of the polymers exhibited a dependence on the M_v of the obtained polymers that was changed by variation in polymerization parameters. Copyright © 2016 John Wiley & Sons, Ltd.     

Synthesis of hyperbranched poly(ether nitrile)s by one‐step polycondensation of an AB2 monomer

Hyperbranched poly(ether nitrile)s were prepared from a novel AB₂ type monomer, 2‐chloro‐4‐(3,5‐dihydroxyphenoxy)benzonitrile, via nucleophilic aromatic substitution. Soluble and low‐viscous hyperbranched polymers with molecular weights upto 233,600 (M_w) were isolated. According to the ¹H NMR and GPC data, the unique polymerization behavior was observed, which implies that the weight average molecular weight increased after the number average molecular weight reached plateau region. Model compounds were prepared to characterize the branching structure. Spectroscopic measurements of the model compounds and the resulting polymers, such as ¹H, DEPT ¹³C NMR, and MS, strongly suggest that the ether exchange reaction and cyclization are involved in the propagation reaction. The side reactions would affect the unique polymerization behavior. The resulting polymers showed a good solubility in organic solvents similar to other hyperbranched aromatic polymers. The hydroxy‐terminated polymer was even soluble in basic water. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5835–5844, 2009     

Stereospecific and molecular weight‐controlled polymerization of 1,3‐butadiene with Co(acac)3‐MAO catalyst

The polymerization of butadiene (Bd) with Co(acac)₃ in combination with methylaluminoxane (MAO) was investigated. The polymerization of Bd with Co(acac)₃‐MAO catalysts proceeded to give cis‐1,4 polymers (94 – 97%) bearing high molecular weights (40 × 10⁴) with relatively narrow molecular weight distributions (M_w's/M_n's). The molecular weight of the polymers increased linearly with the polymer yield, and the line passed through an original point. The polydispersities of the polymers kept almost constant during reaction time. This indicates that the microstructure and molecular weight of the polymers can be controlled in the polymerization of Bd with the Co(acac)₃‐MAO catalyst. The effects of reaction temperature, Bd concentration, and the MAO/Co molar ratio on the cis‐1,4 microstructure and high molecular weight polymer in the polymerization of Bd with Co(acac)₃‐MAO catalyst were observed. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2793–2798, 2001     

Synthesis,light emission,and photovoltaic properties of perylene‐containing polyacetylenes

Perylene (Py)‐containing polyacetylenes with different skeleton structures ? [HC?C(C₆H₄)CO₂? Py]_n? (P 1 ), ? [HC?C(CH₂)₈CO₂? Py]_n? (P 2 ), and ? {[(C₆H₅) C?C(CH₂)₉NH₂]? co? [(C₆H₅)C?C(CH₂)₉? Py]}_n? (P 3 ) are synthesized in satisfactory yields by Rh‐catalyzed polymerization (for P 1 and P 2 ) and polymer reaction (for P 3 ). All the polymers are soluble and possess high molecular weights (M_w up to 2.8 × 10⁵). Their structures and properties are characterized and evaluated by IR, NMR, UV, TGA, PL, and photovoltaic (PV) analyses. The polymers are thermally stable, losing little of their weights when heated to 330 °C. When their solutions are irradiated, their perylene pendants emit intense red fluorescence at 610 nm. PV cells with a configuration of ITO/PEDOT:PSS/polymer/LiF/Al are fabricated, which show maximum current density of 10.3 μA/cm². The external quantum efficiency is sensitive to the polymer structure, with P 3 exhibiting the highest value of 0.23%. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2025–2037, 2008     

Synthesis of end-capped polyester from SmI2-catalyzed Tishchenko-type polyaddition of dialdehydes

SmI₂-catalyzed polyaddition of 1,12-dodecanedial followed by treatment with benzaldehyde gives a polyester (1) containing three structural units, [OCH₂-(CH₂)₁₀-CH₂O], [OCH₂-(CH₂)₁₀-CO], and [CO-(CH₂)₁₀-CO], in the main chain and an OCH₂Ph end-capping group. GPC analysis of 1 shows molecular weights of M_n = 5.5 × 10³ and M_w = 14 × 10³. The ¹H-NMR spectrum reveals the polymer structure with the COOCH₂Ph end group as well as the M_n value (2.6 × 10³) calculated based on an amount of the end-capping group and lower than that estimated from GPC. Mixtures of terephthalaldehyde and 1,12-dodecanedial in several molar ratios undergo similar polyaddition catalyzed by SmI₂ to give the corresponding copolyesters after treatment with benzaldehyde. Increase in the ratio of 1,12-dodecanedial causes increase in yield and molecular weight of the copolymer. Terephthalaldehyde shows a tendency to give alcohol-side —O—R—O— unit in the polyester, whereas 1,12-dodecanedial is mostly incorporated as the acid-side —CO—R′—CO— unit. Terminal aldehyde group derived from dodecanedial is capped effectively by benzaldehyde to give the COOCH₂Ph end group. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 2821–2825, 1997     

Vinyl ethers with a functional group: Living cationic polymerization and synthesis of monodisperse polymers

The living cationic polymerization of vinyl ethers (VEs) having a (polar) functional pendant has been achieved by the hydrogen iodide/iodine (HI/I₂) initiating system to give polymers with a very narrow molecular weight distribution (MWD) (M_w/M_n ≤ 1.2). The functional pendants include benzyl, saturated or unsaturated ester, (poly) oxyethylene, and substituted phenoxyl groups. Although these polar groups often disturb cationic vinyl polymerization by inducing chain transfer and termination, the HI/I₂ initiator cleanly polymerized the “functionalized” VEs without side reactions, mostly in nonpolar media at low temperatures below −15 °C. The HI/I₂-initiated living polymerization also provided facile methods to synthesize new functional polymers, including water-soluble polymers, macromolecular amphiphiles, and macromers, all having a narrow MWD. The simplest example is the living polymerization of VEs carrying an oxyethylene chain [-(CH₂CH₂O)_n-R] as pendant, which directly yields water-soluble polymers. The debenzylation of poly(benzyl VE) prepared with HI/I₂ led to poly(vinyl alcohol). Polymers of the saturated ester-containing monomers (2-acetoxyethyl and 2-benzoyloxyethyl VEs) were readily hydrolyzed into poly (2-hydroxyethyl VE), soluble in water and swellable in methanol. This lead was extended to the synthesis of a new amphiphile, poly(cetyl VE-b-2-hydroxyethyl VE), from a block copolymer of cetyl and 2-acetoxyethyl VEs prepared by their sequential living polymerization initiated with HI/I₂. An adduct between HI and 2-vinyloxyethyl methacrylate [CH₃-CH(I)-OCH₂CH₂OCOC(CH₃) =CH₂] was found to initiate living polymerizations of VEs in the presence of iodine; the products were methacrylate-type macromers carrying a poly(VE) side chain with a narrow chain-length distribution.     

Polymerization of 1-(trimethylsilyl)-1-propyne homologs containing two silicon atoms by tantalum- and niobium-based catalysts

Polymerization of new 1-(trimethylsilyl)-1-propyne homologs containing two silicon atoms [CH₃C?CSi(CH₃)₂CH₂Si(CH₃)₃ and CH₃C?CSi(CH₃)₂CH₂CH₂Si(CH₃)₃] was investigated by use of Ta and Nb catalysts. CH₃C?CSi(CH₃)₂CH₂Si(CH₃)₃ was polymerized quantitatively by TaCl₅ alone to provide a polymer having molecular weight over 10⁶. CH₃C?CSi(CH₃)₂CH₂CH₂Si(CH₃)₃ was polymerized in good yield by an equimolar mixture of TaCl₅ with an appropriate organometallic cocatalyst such as Ph₄Sn to give a polymer with molecular weight of ca. 4 X 10⁵. Nb catalysts were less active toward these monomers than the corresponding Ta catalysts. These two kinds of polymers had alternating double bonds along the main chain according to IR and ¹³C-NMR spectra. Both polymers were white solids completely soluble in low-polarity solvents like toluene, and solution casting afforded uniform, tough films. These polymers were thermally fairly stable, and their softening points were above 350°C. Films of these polymers showed smaller oxygen permeability coefficients [P = 4 × 10^?9 – 8 × 10^?9 cm³(STP) · cm/(cm²·sec·cmHg)] but larger separation factors [(P/P) = 3.4 – 3.6] than a poly[1-(trimethylsilyl)-1-propyne] film.     

Well phase separated segmented copolymers via acyclic diene metathesis (ADMET) polymerization

Segmented oligomers consisting of polyoctenylene hard segments and unsaturated polytetrahydrofuran soft segments were prepared using acyclic diene metathesis (ADMET) copolymerization techniques. These are the first such segmented materials prepared via metathesis chemistry. Two different molecular weight α,ω-poly(tetrahydrofuran)diene soft segment monomers of the structure [CH₂CH(CH₂)₄[O(CH₂)₄]-_nO(CH₂)₄CHCH₂] (1) were synthesized by the cationic living polymerization of tetrahydrofuran (THF). Trifluoromethanesulfonic anhydride, (CF₃SO₂)₂O (triflic anhydride) (2), was employed as the initiator, followed by in situ bis-functionalization with 5-hexen-1-ol, [CH₂=CH(CH₂)₄OH] (3), to yield soft segment dienes with vinyl end groups. The functionality of these soft segment monomers was approximately 1.9. These telechelic monomers possessed sufficient functionality to be homopolymerized or copolymerized with 1,9-decadiene (4) to generate well phase separated, segmented oligomers exhibiting hard segment/soft segment thermal behavior. The segmented copolymers were characterized by ¹H-NMR, ¹³C-NMR, and IR spectroscopy, elemental analysis, and TGA and DSC analysis. Average molecular weights were determined by gel permeation chromatography (GPC) and end-group analysis. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 3441–3449, 1997     

A facile strategy to modify TiO2 nanoparticles via surface‐initiated ATRP of styrene

A core‐shell hybrid nanocomposites, possessing a hard core of nano titanium dioxide (n‐TiO₂) and a soft shell of brushlike polystyrene (PS), were successfully prepared by surface‐initiated atom transfer radical polymerization (ATRP) at 90 °C in anisole solution using CuBr/PMDETA as the catalyst, in the presence of sacrificial initiator. FTIR, ¹H NMR, XPS, TEM, SEM, TGA, and DSC were used to determine the chemical structure, morphology, thermal properties, and the grafted PS quantities of the resulting products. TEM images of the samples provided direct evidence for the formation of a core‐shell structure. The thermal stabilities of the grafted polymers were dramatically elevated relative to that of pristine PS according to TGA results. DSC results demonstrated that the TiO₂‐PS nanocomposites exhibited higher glass transition temperature (T_g) compared with pristine PS. The molecular weights of the free polymers formed by sacrificial initiator, which were similar to that of surface‐attached polymers were measured by GPC instrument which showed that the molecular weights of PS were well controlled with a relatively narrow polydispersity index (PDI < 1.2). © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1782–1790, 2010     

Living cationic polymerization of cis- and trans-ethyl propenyl ethers and synthesis of block copolymers with isobutyl vinyl ether

The cationic polymerization of cis- and trans-ethyl propenyl ethers (EPE, CH₃? CH?CH? O? C₂H₅), initiated by a mixture of hydrogen iodide and iodine (HI/I₂ initiator) at ?40°C in nonpolar media (toluene and n-hexane), led to living polymers of controlled molecular weights and a narrow molecular weight distribution (MWD) (M?_w/M?_n = 1.2–1.3). The geometrical isomerism of the monomer did not affect the living character of the polymerization. ¹³C NMR stereochemical analysis of the polymers showed that the living propagating end is sterically less crowded than nonliving counterparts generated by conventional Lewis acids (e.g., BF₃OEt₂). New block copolymers between EPE (cis or trans) and isobutyl vinyl ether were also prepared by sequential living polymerization of the two monomers.