N‐(3,4‐Dihydroxyphenethyl)‐3,5‐dinitrobenzamide‐Modified Multiwall Carbon Nanotubes Paste Electrode as a Novel Sensor for Simultaneous Determination of Penicillamine,Uric acid,and Tryptophan

N‐(3,4‐dihydroxyphenethyl)‐3,5‐dinitrobenzamide modified multiwall carbon nanotubes paste electrode was used as a voltammetric sensor for oxidation of penicillamine (PA), uric acid (UA) and tryptophan (TP). In a mixture of PA, UA and TP, those voltammograms were well separated from each other with potential differences of 300, 610, and 310 mV, respectively. The peak currents were linearly dependent on PA, UA and TP concentrations in the range of 0.05–300, 5–420, and 1.0–400 µmol L^?1, with detection limits of 0.021, 2.0, and 0.82 µmol L^?1, respectively. The modified electrode was used for the determination of those compounds in real samples.     

Fabrication and Characterization of Carbon Nanotube‐Hydroxyapatite Nanocomposite: Application to Anodic Stripping Voltammetric Determination of Cadmium

A novel chemically modified electrode for stripping determination of cadmium is presented in this paper, based on carbon nanotube‐hydroxyapatite (CNT‐HAP) nanocomposite, which can be prepared by an easy and effective one‐step sonication. The newly synthesized nanocomposite was characterized with FTIR, TEM, and electrochemical methods. Due to the combination of the strong absorption ability of HAP and excellent electroanalytical properties of CNTs, the GC/CNT‐HAP electrode has been successfully used for determination of Cd²⁺ by anodic stripping voltammetry with a linear range of 20 nM–3 μM. The sensitivity and detection limit are 25.6 μA/μM and 4 nM, respectively. The practical application of the proposed electrode has been carried out for the determination of trace levels of Cd²⁺ in real water samples.     

Determination of Uric Acid and Norepinephrine by Chitosan‐Multiwall Carbon Nanotube Modified Electrode

A novel chemically modified electrode based on the chitosan‐multiwall carbon nanotube (MWNT) coated glassy carbon electrode (GCE) is described, which exhibited an attractive ability to determine uric acid (UA) and norepinephrine (NE) simultaneously. The responses of UA and NE merged into a large peak at a bare GCE, but yielded two well‐defined oxidation peaks at the chitosan‐MWNT modified GCE (MC/GCE). The experimental parameters were optimized, and a direct electrochemical method for the simultaneous determine for UA and NE is proposed. The MC/GCE showed good sensitivity, selectivity and stability.     

An Electrochemical Sensor Based on Carbon Nanotube Bimetallic Au‐Pt Inorganic‐Organic Nanofiber Hybrid Nanocomposite Electrode Applied for Detection of Guaifenesin

A glassy carbon electrode modified with carbon nanotube and bimetallic inorganic‐organic nanofiber hybrid nanocomposite was prepared and used for determination of trace levels of guaifenesin. A modified glassy carbon electrode was developed for the rapid, selective, sensitive and low cost monitoring of guaifenesin. Oxidation of guaifenesin on the surface of the modified electrode was investigated with differential pulse voltammetry and the results showed that the modified electrode remarkably improved sensitivity and selectivity for the electrochemical assay of guaifenesin. Detection limit and quantitation limit were found to be 0.0175 µM and 0.0583 µM, respectively.     

FTIR Spectroscopic Study of Crystallization of Uniaxial Drawn Syndiotactic Polystyrene/Carbon Nanotube Nanocomposite Films

The crystallization of uniaxial hot drawn syndiotactic polystyrene/multi-walled carbon nanotube (sPS/MWCNT) nanocomposite films was studied by FTIR spectroscopy. The effects of MWCNT content, draw ratio and drawing temperature on the sPS crystallinity were investigated. The sPS/MWCMT nanocomposite films show reduced crystallinities with the increase of MWCNT content. In addition, with the increase of draw ratio, both the pure sPS and the sPS/MWCNT nanocomposite drawn films exhibit increased crystallinity. The effect of drawing temperature on the sPS crystallization is complex. In a temperature range of 100―135 ℃, the crystallinity decreases with drawing temperature, whereas it increases at 140 ℃ for both pure sPS and its nanocomposite films.     

Selective and Simultaneous Voltammetric Determination of Glutathione,Uric Acid and Penicillamine by a Modified Carbon Nanotube Paste Electrode

In this paper, the use of a carbon paste electrode (CPE) modified by (E)‐3‐((2‐(2,4‐dinitrophenyl)hydrazono)methyl)benzene‐1,2‐diol (DHB) and carbon nanotubes (CNTs) for the determination of glutathione (GSH), uric acid (UA) and penicillamine (PA) is described. Initially, cyclic voltammetry was used to investigate the redox properties of the modified electrode in phosphate buffer. Next, the electrocatalytic oxidation of GSH via EC′ mechanism at the modified electrode was described. At the optimum pH of 7.0, the oxidation of GSH occurs at a potential that is 530 mV less positive than that of an unmodified carbon paste electrode. The values of the diffusion coefficient (D=2.5×10^?6 cm² s^?1) and the catalytic rate constant (k=1.7×10³ M^?1 s^?1) were calculated for GSH, using chronoamperometry. Based on differential pulse voltammetry, the oxidation of GSH exhibited a dynamic range between 0.4 and 700.0 µM and a detection limit (3σ) of 70.0 nM. Also, simultaneous determination of GSH, UA and PA was described at the modified electrode. Finally, this method was used for the determination of these substances in synthetic solutions and blood serum samples.     

Electrochemical Analysis of D‐Penicillamine Using a Carbon Paste Electrode Modified with Ferrocene Carboxylic Acid

The electrochemical behavior of D ‐penicillamine (D ‐PA) studied at the surface of ferrocene carboxylic acid modified carbon paste electrode (FCAMCPE) in aqueous media using cyclic voltammetry and double step potential chronoamperometry. It has been found that under optimum condition (pH 7.00), the oxidation of D ‐PA at surface of such an electrode is occurred about 420 mV less positive than that an unmodified carbon paste electrode (CPE). The catalytic oxidation peak current was linearly dependent on the D ‐PA concentration and a linear calibration curve was obtained in the ranges 7.5×10^?5 M – 1.0×10^?3 M and 6.5×10^?6 M?1.0×10^?4 M of D ‐PA with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods respectively. The detection limits (3σ) were determined as 6.04×10^?5 M and 6.15×10^?6 M. This method was also used for the determination of D ‐PA in pharmaceutical preparation (capsules) by standard addition method.     

A Voltammetric Sensor Based on Modified Multiwall Carbon Nanotubes for Cysteamine Determination in the Presence of Tryptophan Using p‐Aminophenol as a Mediator

Determination of cysteamine and tryptophan is described by electrochemical methods using p‐aminophenol‐multiwall carbon nanotubes paste electrode. Cysteamine and tryptophan in mixture can each be measured independently from each other with a potential difference of 600 mV. The results showed that the electrocatalytic currents increased linearly with cysteamine and tryptophan concentrations over the ranges 0.5–300 µmol L^?1 and 10.0–650 µmol L^?1, respectively. The detection limits for cysteamine and tryptophan are found to be 0.14 and 5.9 µmol L^?1, respectively. The proposed method is successfully employed for the determination of cysteamine in both capsule and urine samples.     

Evaluation of Meldola Blue‐Carbon Nanotube‐Sol‐Gel Composite for Electrochemical NADH Sensors and Their Application for Lactate Dehydrogenase‐Based Biosensors

A novel MB‐SWNT‐sol‐gel nanocomposite material was prepared by the sol‐gel process incorporating a redox mediator and carbon nanotubes. The electrocatalytic properties of the nanomaterial based sensor toward NADH oxidation were studied by electrochemical measurements. Significant enhancement of oxidation current is obtained at electrodes modified by MB‐SWNT‐sol‐gel in comparison with the analogous carbon black and/or graphite composite modified electrode. The usefulness of the nanocomposite material as a matrix for immobilizing enzymes is also demonstrated. Analytical parameters of D ‐lactate biosensors with and without SWNT in the hybrid film were compared demonstrating that performance of the biosensor was significantly improved when introducing SWNT.     

Multiwall Carbon Nanotube (MWCNT) Based Electrochemical Biosensors for Mediatorless Detection of Putrescine

γ‐Aminopropyltriethoxysilane (APTES)‐induced solubilization of multi‐wall carbon nanotube CNTs allowed for the modification of electrode surfaces. APTES also served as an immobilization matrix for putrescine oxidase (POx) to construct an amperometric biosensor. Although CNTs modified by APTES acted as semiconductors to reduce the exposed sensing surface, we reasoned that nanoscale “dendrites” of CNTS modified by APTES formed a network and projected outwards from the electrode surface and acted like bundled ultra‐microelectrodes that allowed access to the active site and facilitated direct electron transfer to the immobilized enzyme. Our biosensor was able to efficiently monitor direct electroactivity of POx at the electrode surface. The putrescine biosensor prepared using the modified glassy carbon electrode exhibited current response within 10 s with a detection limit of 500 nM.     

三维碳微米管/碳纳米管复合结构的制备及在超级电容器中的应用

利用天然生物质杨絮特殊的管状结构通过简单的高温碳化法制备出碳微米管(CMTs). 将所得到的碳微米管作为基底, 采用化学气相沉积法制备出三维结构的碳微米管/碳纳米管(CNTs)复合材料. 利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线衍射(XRD)光谱仪、拉曼光谱仪对其进行了详细分析. 通过两电极测试体系对其超级电容性能进行测试, 碳微米管/碳纳米管复合电极在1 mol·L^-1Li₂SO₄电解液中的比电容值可达77 F·g^-1, 远大于碳微米管的比电容值(23 F·g^-1).     

Preparation,Characterization and Electrochemical Application of ZnO‐CuO Nanoplates for Voltammetric Determination of Captopril and Tryptophan Using Modified Carbon Paste Electrode

2‐chlorobenzoyl ferrocene, was synthesized and used to construct a modified ZnO‐CuO nanoplates modified carbon paste electrode. The electrooxidation of captopril at the surface of the modified electrode was studied. Under the optimized conditions, the square wave voltammetric (SWV) peak current of captopril increased linearly with captopril concentration in the range of 5.0×10^?7 to 9.0×10^?4 M and detection limit of 90.0 nM was obtained for captopril. The diffusion coefficient and kinetic parameters (such as electron transfer coefficient and the heterogeneous rate constant) for captopril oxidation were also determined. The prepared modified electrode exhibits a very good resolution between the voltammetric peaks of captopril and tryptophan which makes it suitable for the detection of captopril in the presence of tryptophan in real samples.     

Simultaneous Detection of Heavy Metals by Anodic Stripping Voltammetry Using Carbon Nanotube Thread

Carbon nanotube (CNT) threads are a type of CNT arrays that consist of super long CNTs. CNT threads inherit the advantages of CNTs, while avoiding the potential toxicity caused by individual CNTs. Electrodes based on CNT threads were fabricated and used for simultaneous detection of trace levels of Cu²⁺, Pb²⁺ Cd²⁺ and Zn²⁺ by anodic stripping voltammetry (ASV). The detection limits are 0.27 nM, 1.5 nM, 1.9 nM and 1.4 nM for Cu^2+, Pb²⁺, Cd²⁺ and Zn²⁺, respectively, in 0.1 M acetate buffer pH 4.5. The CNT thread electrode gives well‐defined, reproducible and sharp stripping signals for individual and simultaneous detection of heavy metals.     

A Glassy Carbon Electrode Modified with Multiwalled Carbon Nanotube/Chitosan Composite as a New Sensor for Simultaneous Determination of Acetaminophen and Mefenamic Acid in Pharmaceutical Preparations and Biological Samples

A new chemically modified electrode is constructed based on multiwalled carbon nanotube/chitosan modified glassy carbon electrode (MWCNTs‐CHT/GCE) for simultaneous determination of acetaminophen (ACT) and mefenamic acid (MEF) in aqueous buffered media. The measurements were carried out by application of differential pulse voltammetry (DPV), cyclic voltammetry (CV) and chronoamperometry (CA) methods. Application of DPV method showed that the linear relationship between oxidation peak current and concentration of ACT and MEF were 1 μM to 145 μM, and 4 μM to 200 μM, respectively. The analytical performance of this sensor has been evaluated for detection of ACT and MEF in human serum, human urine and a pharmaceutical preparation with satisfactory results.     

Functionalization of Multi Carbon Nanotubes with 1,2‐Naphthoquinone‐4‐sulfonic Acid Sodium: A Novel Sulphydryl Compounds Sensor Based on Functionalized Carbon Nanotube Film Using Michael Addition

The functionalized multi‐wall carbon nanotube with 1,2‐naphthoquinone‐4‐sulfonic acid sodium (Nq‐MWNT) was fabricated by a simple and low‐cost method. Techniques of scanning electron microscope (SEM) with energy dispersive X‐ray (EDX) analysis, fourier transform infrared spectroscopy (FT‐IR), ultraviolet visible spectroscopy (UV‐vis) and cyclic voltammetry (CV) were used to characterize the property of the Nq‐MWNT. The results showed that the MWNT with high functionalization of Nq can be obtained using this simple method. The Nq‐MWNT modified carbon paste electrode (Nq‐MWNT/CPE) was fabricated by drop‐casting technique. The resulted modified electrode was tested successfully to detection D‐penicillamine (D‐PA) and captopril (CAP) in an aqueous solution. It is found that D‐PA and CAP participate in Michael addition reaction with Nq on MWNT to form the corresponding thioquinone derivative. The reoxidation of adducts at a potential of less positive than D‐PA and CAP at the surface of the bare CPE leads to an increase in the oxidative current, which is proportional to the concentration of D‐PA and CAP. The catalytic response showed a wide linear range (3‐200 μM and 1‐130 μM for D‐PA and CAP, respectively) as well as its experimental limit of detection can be achieved 0.8 μM, and 0.4 μM for D‐PA and CAP, respectively. The modified electrode for D‐PA and CAP determination is of the property of simple preparation, good stability and high sensitivity. Furthermore, the fabricated electrode was used to determine the content of D‐PA and CAP in the tablet, suggesting the good accuracy of the method.     

One‐Step Electrochemically Deposited Nanocomposite Film of CS‐Fc/MWNTs/GOD for Glucose Biosensor Application

A simple and controllable electrodeposition approach was proposed for one‐step construction of glucose biosensors by in situ co‐deposition of ferrocene‐branched chitosan derivatives (CS‐Fc), multiwalled carbon nanotubes (MWNTs), and glucose oxidase (GOD) onto electrode surface. The formation of CS‐Fc could not only effectively prevent the leakage of Fc and retain its electrochemical activity, but also provide a biocompatible microenvironment for retaining the native activity of the immobilized biomolecules. Further entrapment of MWNTs into the CS matrix improved electronic conductivity of the biocomposite significantly. The facile procedure of immobilizing GOD and the promising feature of biocomposite will offer a versatile platform to fabricate biosensors and bioelectronic devices.     

Fabrication of Photoelectrochemical Glucose Biosensor in Flow Injection Analysis System Using ZnS/CdS‐Carbon Nanotube Nanocomposite Electrode

In this work, a photoamperometric glucose biosensor based on glucose oxidase (GODx) was developed in flow injection analysis (FIA) system using ZnS‐CdS quantum dot (QD) modified multiwalled carbon nanotube/glassy carbon electrode (ZnS‐CdS/MWCNT/GCE). Cyclic voltammograms of the proposed electrode (GODx/ZnS‐CdS/MWCNT/GCE) showed a pair of well‐defined reversible redox peak attributing that direct electron transfer between the protein and electrode. The current of the reduction peak became more cathodic in the presence of O₂ due to the electrocatalytic activity of the electrode towards the reduction of dissolved O₂, but reduction current shifted to a less negative value upon addition of glucose in the solution. The obtained CV currents were affected by the irradiation of the electrode surface. Thus, the photoelectrochemical biosensing of glucose in the FIA system was studied by monitoring of the changes in the electrocatalyzed reduction peak current of dissolved O₂ at the proposed electrode dependent on glucose concentration. The proposed photoelectrochemical FIA method has a linear response to glucose ranging from of 0.01 to 1.0 mM with detection limit of 3.0 μM under optimized conditions. Photoelectrochemical biosensor was successfully fabricated in FIA system for selective, sensitive and repeatable detection of glucose and has been satisfactorily applied to determination of glucose in real sample.     

Preparation,Characterization and Electrochemical Application of ZnS/ZnAl2S4 Nanocomposite for Voltammetric Determination of Methionine and Tryptophan Using Modified Carbon Paste Electrode

ZnS/ZnAl₂S₄ nanocomposite and 2‐chlorobenzoyl ferrocene, were synthesized and used to construct a modified carbon paste electrode. The electrooxidation of methionine at the surface of the modified electrode was studied. Under the optimized conditions, the square wave voltammetric (SWV) peak current of methionine increased linearly with methionine concentration in the range of 5.0×10^?8 to 8.0×10^?4 M and detection limit of 10.0 nM was obtained for methionine. The prepared modified electrode exhibits a very good resolution between the voltammetric peaks of methionine and tryptophan which makes it suitable for the detection of methionine in the presence of tryptophan in real samples.     

WC/CNT纳米复合材料制备及其对甲醇氧化的电催化性能

采用表面修饰技术将碳纳米管(CNT)表面羧基化, 通过羧基将钨离子基团修饰到碳纳米管的外表面, 再通过原位还原碳化技术, 将钨离子基团还原成碳化钨(WC)纳米微粒, 制备出WC/CNT纳米复合材料. 采用FTIR、XRD、SEM、HRTEM和N2吸附等分析测试手段对样品的形貌、晶相组成和微观结构特征进行了表征. FTIR和N2吸附结果表明, 硝化后, 在碳纳米管表面羧基化的同时比表面积增加; XRD结果表明, WC/CNT样品由碳纳米管、WC以及非化学计量比的氧化钨组成; SEM和HRTEM结果表明, WC纳米颗粒均匀地分散于碳纳米管的外表面,并与碳纳米管构成了复合材料. 采用循环伏安法测试了样品在碱性条件下对甲醇氧化的电催化性能, 结果表明, 复合材料对甲醇氧化的电催性能明显强于WC 和碳纳米管, 并在实验结果的基础上探讨了复合材料催化性能提高的原因.     

Direct Electrochemistry and Bioelectrocatalysis of Microperoxidase‐11 Immobilized on Chitosan‐Graphene Nanocomposite

A bioelectrochemical platform has been constructed for the direct electron transfer and biosensing purposes of microperoxidase‐11 (MP‐11) immobilized on the chitosan dispersed multilayer graphene nanocomposite. The immobilized MP‐11 at the modified gold electrode displays a well‐defined and quasireversible redox peaks, with a formal potential of ?0.38 V/SCE in a buffer solution (pH 7.0). MP‐11 absorbed on the electrode surface exhibits high electrocatalytic activity toward the reduction of both oxygen and hydrogen peroxide and also shows good analytical performance for the amperometric detection of H₂O₂ with a linear range from 2.5 to 135 μM. These results indicate the graphene modified electrode might be used as a third generation biosensor for H₂O₂ detection.