一维六方压电准晶中唇形匀速移动裂纹问题的解析解

运用复变函数方法,通过构造保角映射,研究了在电非渗透型边界条件下一维六方压电准晶中唇形快速传播裂纹问题的反平面剪切问题,获得了III型裂纹动态的应力强度因子和电位移强度因子的解析解．研究结果表示,当裂纹传播速度趋于零时,动力学问题就还原为了静力学问题的解．当唇形裂纹的高度趋于零时,所得结果可以退化为Griffth裂纹问题．     

压电效应下一维六方准晶双材料孔边裂纹的反平面问题研究

利用复变函数方法和保角变换技术研究了压电效应下一维六方准晶双材料中圆孔边单裂纹的反平面问题．考虑电不可渗透型边界条件,运用保角变换和Stroh公式得到了弹性体受远场剪切力和面内电载荷作用下裂纹尖端应力强度因子和能量释放率的解析解. 数值算例分析了几何参数、远场受力、电位移载荷对能量释放率的影响．结果表明：裂纹长度、耦合系数和远场剪切力的减小可以抑制裂纹的扩展．不考虑电场时,声子场应力对能量释放率的影响较小．本文的研究结果可作为研究一维六方压电准晶双材料孔边裂纹问题的理论基础,同时为压电准晶及其复合材料的设计、制备、优化和性能评估提供理论依据．     

一维正方准晶椭圆孔口平面弹性问题的解析解

利用复变方法,引入广义保角映射,研究了一维正方准晶中具有椭圆孔口的平面弹性问题,给出了各应力分量的复变表示,并在特殊情况下转化为Griffith裂纹,得到该裂纹尖端处的应力强度因子的解析解.当准晶体的对称性增加时,正方准晶椭圆孔口平面弹性问题退化为一维四方准晶中具有椭圆孔口的平面弹性问题,同样在特殊情况下转化为Griffith裂纹,得到裂纹尖端处的应力强度因子的解析解.     

含直对称裂纹的一维六方压电准晶对SH波的散射Scattering of SH wave by a linear symmetric crack at one-dimensional piezoelectric hexagonal quasicrystals

利用积分变换技术,结合Copson方法,研究了含直线型对称裂纹的一维六方压电准晶对SH波的散射问题。通过求解对偶积分方程,得到声子场、相位子场应力、位移及电场电位移分量的解析解。定义了裂纹尖端应力强度因子及电位移强度因子,给出了电非渗透性条件下应力强度因子及电位移强度因子的解析解。此研究结果对压电准晶材料的工程应用有一定的理论价值。     

含直对称裂纹的一维六方压电准晶对SH波的散射

利用积分变换技术,结合Copson方法,研究了含直线型对称裂纹的一维六方压电准晶对SH波的散射问题。通过求解对偶积分方程,得到声子场、相位子场应力、位移及电场电位移分量的解析解。定义了裂纹尖端应力强度因子及电位移强度因子,给出了电非渗透性条件下应力强度因子及电位移强度因子的解析解。此研究结果对压电准晶材料的工程应用有一定的理论价值。     

热电材料孔边周期裂纹问题的热电弹分析

论文研究了均匀电流密度和能量流作用下,热电材料中带4k个周期径向裂纹的圆形孔口问题.考虑非渗透型电和热边界条件,运用复变函数理论和保形映射方法,得到了热电材料中电流密度、能量密度和应力场的精确解.依据断裂力学理论,运用Cauchy积分公式得到了周期裂纹的电流、能量和应力强度因子.数值结果分析了场强度因子随各个参数的变化...     

功能梯度压电带中裂纹对SH波的散射

研究功能梯度压电带中裂纹对SH波的散射问题,为了便于分析,材料性质假定为指数模型,并假设裂纹面上的边界条件为电渗透型的.根据压电理论得到压电体的状态方程,利用Fourier积分变换,问题转化为对偶积分方程的求解.用Copson方法求解积分方程.求得了裂纹尖端动应力强度因子、电位移强度因子的解析表达式,最后数值结果显示了标准动应力强度因子与入射波数、材料参数、带宽、波数以及入射角之间的关系.     

一维六方准晶压电材料中唇形裂纹反平面问题的解析解

本文在准晶压电材料基本方程的基础上,根据点群的对称性和一维六方准晶的线性压电效应,导出了一维六方准晶压电材料反平面问题的控制方程.利用复变函数的方法,通过引入适当的保角映射,研究了准晶压电材料中唇形裂纹的反平面问题,并利用Cauchy积分理论,得到在电不可通边界条件下的裂纹尖端场强度因子与机械应变能释放率的解析表达式.     

压电体中考虑表面效应时开裂孔洞的断裂特征

研究了反平面机械载荷和面内电载荷作用下压电体中考虑表面效应时孔边双裂纹问题的断裂特征.基于Gurtin-Murdoch表面理论模型,通过构造映射函数,利用复势电弹理论获得了应力场和电位移场的闭合解答.给出了裂纹尖端应力强度因子、电位移场强因子和能量释放率的解析解.讨论了开裂孔洞几何参数和施加力电载荷对电弹场强因子和能量释放率的影响.     

一维六方准晶压电材料中多缺陷的相互作用

基于准晶压电材料的基本方程,利用解析函数理论和复变方法,研究了一维六方准晶压电材料中多缺陷的相互作用问题,建立了多条平行位错以及它们与半无限裂纹相互作用的断裂力学模型,给出了一维六方准晶压电材料中n条平行位错相互作用的Peach Koehler公式和n条平行位错的等效作用点,得到了n条平行位错与半无限裂纹相互作用下电弹性场的解析解,数值算例给出了位错位置对裂纹面上应力的影响和位错Burgers矢量的大小对裂纹面上应力的影响,为讨论裂纹尖端的位错发射、位错屏蔽和裂纹钝化奠定了理论基础.这些结果均为本文首次给出,丰富和发展了经典弹性理论中的相应结果.     

一维六方准晶中星形静态裂纹和运动裂纹的解析解

利用复变函数方法研究了一维六方准晶中星形静态裂纹和运动裂纹的反平面剪切问题,得到了星形裂纹尖端处应力强度因子和动应力强度因子的解析解.当裂纹条数给定时,由此可得到直线裂纹,Griffith裂纹,共点均匀分布三裂纹,对称十字形裂纹,米字型裂纹(对称八裂纹)静力学和动力学问题的解析解.当k=4时,用数值算例讨论了声子场-相位子场耦合系数和裂纹运动速度对动应力强度因子的影响.当速度趋于0时,运动裂纹的解可以退化为静态裂纹的解.     

Anti-plane analysis of semi-infinite crack in piezoelectric strip

Using the complex variable function method and the technique of the conformal mapping, the fracture problem of a semi-infinite crack in a piezoelectric strip is studied under the anti-plane shear stress and the in-plane electric load. The analytic solutions of the field intensity factors and the mechanical strain energy release rate are presented under the assumption that the surface of the crack is electrically impermeable. When the height of the strip tends to infinity, the analytic solutions of an infinitely large piezoelectric solid with a semi-infinite crack are obtained. Moreover, the present results can be reduced to the well-known solutions for a purely elastic material in the absence of the electric loading. In addition, numerical examples are given to show the influences of the loaded crack length, the height of the strip, and the applied mechanical/electric loads on the mechanical strain energy release rate.     

A half plane crack under three-dimensional combined mode impact loading

The dynamic stress intensity factor history for a half plane crack in an otherwise unbounded elastic body, with the crack faces subjected to a traction distribution consisting of two pairs of suddenly-applied shear line loads is considered. The analytic expression for the combined mode stress intensity factors as a function of time is obtained. The method of solution is based on the application of integral transforms and the Wiener-Hopf technique. Some features of the solutions are discussed and graphical numerical results are presented. The project supported by the National Natural Science Foundation of China     

Exact Analytical Solutions of Three-Dimensional Static Thermoelastic Problems for a Transversally Isotropic Body in Curvilinear Coordinate Systems

An approach to the solution of three-dimensional static thermoelastic problems for a transversally isotropic (the case of rectangular anisotropy) body is proposed. The results of construction of the general analytic solutions to thermoelastic problems for canonical bodies are systematized. The exact analytic solutions of three-dimensional problems are obtained. It is assumed that the bodies under consideration are thermoelastic and their boundary surface corresponds to the coordinate surfaces in coordinate systems that allow separating the variables in the three-dimensional Laplace equation. The stress concentration near cavities and inclusions is studied. The stress intensity factors near elliptic and hyperbolic cracks are determined. Formulas are presented for the stress intensity factors on the surface of a rigid elliptic inclusion and inside the body near a homogeneity under various thermal effects     

Exact solutions of two semi-infinite collinear cracks in piezoelectric strip

Using the complex variable function method and the conformal mapping technique,the fracture problem of two semi-infinite collinear cracks in a piezoelectric strip is studied under the anti-plane shear stress and the in-plane electric load on the partial crack surface.Analytic solutions of the field intensity factors and the mechanical strain energy release rate are derived under the assumption that the surfaces of the crack are electrically impermeable.The results can be reduced to the well-known solutio...     

Transient thermal shock fracture analysis of functionally graded piezoelectric materials by the extended finite element method

Transient thermal dynamic analysis of stationary cracks in functionally graded piezoelectric materials (FGPMs) based on the extended finite element method (X-FEM) is presented. Both heating and cooling shocks are considered. The material properties are supposed to vary exponentially along specific direction while the crack-faces are assumed to be adiabatic and electrically impermeable. A dynamic X-FEM model is developed in which both Crank–Nicolson and Newmark time integration methods are used for calculating transient responses of thermal and electromechanical fields respectively. The generalized dynamic intensity factors for the thermal stresses and electrical displacements are extracted by using the interaction integral. The accuracy of the developed approach is verified numerically by comparing the calculated results with reference solutions. Numerical examples with mixed-mode crack problems are analyzed. The effects of the crack-length, poling direction, material gradation, etc. on the dynamic intensity factors are investigated. It shows that the transient dynamic crack behaviors under the cooling shock differ from those under the heating shock. The influence of the thermal shock loading on the dynamic intensity factors is significant.     

ELASTIC INTERACTION BETWEEN WEDGE DISCLINATION DIPOLE AND INTERNAL CRACK

The system of a wedge disclination dipole interacting with an internal crack was investigated. By using the complex variable method, the closed form solutions of complex potentials to this problem were presented. The analytic formulae of the physics variables, such as stress intensity factors at the tips of the crack produced by the wedge disclination dipole and the image force acting on disclination dipole center were obtained. The influence of the orientation, the dipole arm and the location of the disclination dipole on the stress intensity factors was discussed in detail. Furthermore, the equilibrium position of the wedge disclination dipole was also examined. It is shown that the shielding or antishielding effect of the wedge disclination to the stress intensity factors is significant when the disclination dipole moves to the crack tips.     

Antiplane crack at the interface of two bonded dissimilar graded piezoelectric materials

The problem of an antiplane crack situated in the interface of two bonded dissimilar graded piezoelectric half-spaces is considered under the permeable crack assumption. The mechanical and electrical properties of the half-spaces are considered for a class of functional forms for which the equilibrium equation has analytic solutions. By using an integral transform technique, the problem is reduced to dual integral equations which are transformed into a Fredholm integral equation by introducing an auxiliary function. The stress intensity factors are obtained in explicit form in terms of auxiliary functions. By solving the Fredholm integral equation numerically, the numerical results for stress intensity factors are obtained which have been displayed graphically to show the influence of the graded piezoelectric materials.