Mathematical modeling of dispersion in single interface flow analysis

This work describes the optimization of the recently proposed fluid management methodology single interface flow analysis (SIFA) using chemometrics modelling. The influence of the most important physical and hydrodynamic flow parameters of SIFA systems on the axial dispersion coefficients estimated with the axially dispersed plug-flow model, was evaluated with chemometrics linear (multivariate linear regression) and non-linear (simple multiplicative and feed-forward neural networks) models. A D-optimal experimental design built with three reaction coil properties (length, configuration and internal diameter), flow-cell volume and flow rate, was adopted to generate the experimental data. Bromocresol green was used as the dye solution and the analytical signals were monitored by spectrophotometric detection at 614 nm. Results demonstrate that, independent of the model type, the statistically relevant parameters were the reactor coil length and internal diameter and the flow rate. The linear and non-linear multiplicative models were able to estimate the axial dispersion coefficient with validation r² = 0.86. Artificial neural networks estimated the same parameter with an increased accuracy (r² = 0.93), demonstrating that relations between the physical parameters and the dispersion phenomena are highly non-linear. The analysis of the response surface control charts simulated with the developed models allowed the interpretation of the relationships between the physical parameters and the dispersion processes.     

On-line coupling of sorption preconcentration to liquid-chromatographic methods of analysis

Methods of analysis combining the on-line sorption preconcentration of analytes with their subsequent separation and determination by high-performance liquid chromatography are considered. Approaches to the selection of sorbents, the sizes of preconcentration columns, and the sorption and desorption conditions are discussed along with the corresponding instrumentation. Many examples of the determination of organic compounds of different polarity and organic and inorganic ions are presented.     

Mathematical modeling of solution deionization by sorption on aerogel electrodes

The mathematical modeling is used to study the dynamics of solution deionization by sorption on aerogel electrodes. The matter transport by solution flow, diffusion, and sorption in pores are simulated. Several models are proposed to describe the phenomenon with different degree of approximation. Problems arising in numerical computing and ways to solve them are described. It is shown that at low solution concentrations and a small pore size the effect of electro-sorption is not reduced to the formation of a double electric layer on the pore surface, which uptakes ions from the solution. In addition to the formation of this layer distributed ionic charge is accumulated all over the pore space. The dependence of the effective diffusion coefficient inside the porous electrode on the ion concentration is found. Examples of calculating the deionization process at one-cycle and multi-cycle sorption are given.     

On-line coupling of flow injection displacement sorption preconcentration to high-performance liquid chromatography for speciation analysis of mercury in seafood

A simple and cost-effective method for speciation analysis of trace mercury in seafood was developed by on-line coupling flow injection microcolumn displacement sorption preconcentration to high-performance liquid chromatography (HPLC) with UV detection. The methodology involved the presorption of the Cu-PDC (pyrrolidine dithiocarbamate) chelate onto a microcolumn packed with a cigarette filter sorbent, simultaneous preconcentration of Hg(II), methylmercury (MeHg), ethylmercury (EtHg), and phenylmercury (PhHg) onto the microcolumn through a displacement reaction with the presorbed Cu-PDC, and their subsequent elution from the microcolumn for on-line HPLC separation. Interferences from heavy metal ions with lower stability of their PDC chelates relative to Cu-PDC were minimized without the need of any masking agents. With the consumption of 4.0 ml of sample solution, the enrichment factors were about 80. The detection limits were 10-25 ng g(-1) (as Hg) in fresh tissue. Precision (R.S.D. (%), n = 5) ranged from 2 to 3% at the 500 microg l(-1) (as Hg) level. The developed technique was validated by analyzing a certified reference material (DORM-2, dogfish-muscle), and was shown to be useful for mercury speciation in real seafood samples.     

On-line separation and preconcentration in flow injection analysis

Various improvements in flow-injection systems involving on-line separation and preconcentration by gas diffusion, ion-exchange and liquid—liquid extraction are reviewed and their merits are discussed. On-line preconcentration systems based on gas diffusion are described for the spectrophotometric determination of cyanide, fluoride and ammonia. Different gas/liquid separation devices for hydride-generation and cold-vapour atomic absorption spectrometry (a.a.s.) are compared. Systems are outlined for on-line column preconcentration of cobalt, nickel, vanadium, beryllium and cerium for inductively-coupled plasma/atomic emission spectrometry, and for combinations of column preconcentration with hydride-generation and cold-vapour a.a.s for the determination of ultratrace selenium and mercury. An on-line liquid—liquid extraction/flame a.a.s. system capable of achieving 60-fold enhancement for lead is reported; the limit of detection is 0.02 μg ml^?.     

Trends in sorption preconcentration combined with noble metal determination.

Nowadays much attention is being paid to the determination of trace amounts of noble metals in geological, industrial, biological and environmental samples. The most promising techniques, such as inductively coupled plasma atomic emission spectrometry (ICP-AES), inductively coupled plasma mass spectrometry (ICP-MS) and electrothermal atomic absorption spectrometry (ETAAS) are characterized by high sensitivity. However, the accurate determination of trace noble metals has been limited by numerous interferences generated from the presence of matrix elements. To decrease, or eliminate, these interferences, the sorption preconcentration of noble metals is often used prior to their instrumental detection. A great number of hyphenated methods of noble metal determination using sorption preconcentration have been developed. This review describes the basic types of available sorbents, preconcentration procedures and preparations of the sorbent to the subsequent determination of noble metals. The specific features of instrumental techniques and examples of ETAAS, FAAS, ICP-AES, ICP-MS determinations after the sorption preconcentration of noble metals are considered. The references cited here were selected mostly from the period 1996 - 2006.     

Sample preconcentration by continuous flow extraction with a flow injection atomic absorption detection system

The flow manifold described allows automatic extraction of metal ions in aqueous samples into 4-methyl-2-penthanone with ammonium pyrrolidinedithiocarbamate as an extracting agent. The organic extract is led into the loop of an injector situated in an integrated feed system of an atomic absorption spectrometer. No dispersion of the injected organic extract plug, 110 μl, occurs in the aqueous feed stream and the resulting signal from the spectrometer is a peak. An increase in sensitivity of 15–20 is achieved for copper, nickel, lead and zinc in comparison with direct aspiration of the aqueous samples. The sampling frequency is 40 h^?1 and the consumption of 4-methyl-2-pentanone is typically 0.3 ml min^?1. The detection limit for copper is about 1 μ l^?1.     

Specificity of noble metals dynamic sorption preconcentration on reversed-phase sorbents

The reversible sorption preconcentration of noble metals (NMs) using different schemes “sorbent–reagent–eluent” was investigated. The extraction of Au, Pd, Pt, Ir, Rh and Ru chlorocomplexes from hydrochloric acid solutions on hyper-crosslinked polysterene MN-200 in the form of ion associates with tributylamine (TBA) and 4-(n-octyl)diethylenetriamine (ODETA) was investigated. It was found that Pd, Pt and Au were quantitatively and reversibly extracted using TBA on hyper-crosslinked polysterene; the appropriate eluent for desorption was 1 M solution of HCl in ethanol. Ir, Rh and Ru under these conditions were not sorbed quantitatively. It was found that sorbent hydrophobicity is not the main characteristic that defines the efficiency of sorption of a particular NM ion associate. Different efficiencies of hyper-crosslinked polysterene MN-200 for sorption of square-planar chlorcomplexes of Pt, Pd and Au and octahedral complexes of Ir, Rh and Ru were found. For the first time, the sorbents with their own N-atoms – StrataX and StrataX-AW – were used for the sorption of Ir, Rh and Ru. Using these sorbents, the sorption of Ir was increased up to 95%, and the sorption of Ru and Rh was increased to about 40%. We can explain these results by nonspecific interaction of chlorcomplexes of Ir, Rh and Ru with ethylenediamine groups of the sorbent. Weak bases with large anions may be applied for desorption of Ir, Rh and Ru. Two schemes of dynamic sorption preconcentration of NMs from hydrochloric acid solutions were proposed – hyper-crosslinked polysterene MN-200 for the determination of Au, Pd, Pt, and StrataX-AW for Ir, Rh and Ru.     

Mathematical modeling of controlled-relase kinetics of herbicides in a dynamic-water-bath system

Applied Biochemistry and Biotechnology - Release of herbicides from lignin-based formulations follows a diffusion-controlled mechanism. For mathematical modeling of diffusive transport, the...     

Voltammetric determination of doxorubicin in urine by adsorptive preconcentration and flow injection analysis

Preconcentration and quantitation of the cancer chemotherapy drug, doxorubicin, are achieved via a flow-injection approach utilizing adsorption of the drug onto a carbon paste electrode, medium exchange, and differential pulse voltammetry on the adsorbing surface. The oxidation peak at +0.57 V vs. Ag/AgCl is used for quantitation. Linear response was obtained for concentrations from 10^?6 M to the detection limit of 10^?9 M, and it was possible to determine the drug in urine by direct injection of the sample with no preliminary steps required. The sensitivity, linearity, and selectivity of the flow injection approach were markedly improved relative to the earlier batch method in which the adsorption step was done in a stationary sample solution.     

A comparison of preconcentration reagents for flow injection analysis flame atomic spectrometry

A small range of new commercially available chelating resins are compared with a resin prepared in-house in terms of their applicability for on-line preconcentration and matrix separation. The flow injection manifold was designed for rapid matrix separation and the resins were tested for the determination of Cull, ZnII, CdII, MnII and NiII. The resin based on controlled pore glass was found to be better for this rapid procedure because it did not require conditioning, although the polymer based resins had better capacities. The commercially available controlled pore glass based iminodiacetate (IDA) resin had a comparable performance to the in-house controlled pore glass 8-hydroxyquinoline (CPG-8-HQ) resin. The IDA resin had a much higher capacity than the 8-HQ, however as with all IDA based resins, some retention of Call was observed. The sample throughput was 12 h⁻¹.     

Electrolytic preconcentration in instrumental analysis

The use of electrolytic deposition as a separation and preconcentration step in trace metal analysis is reviewed. Both the principles and applications of the technique are dealt with in some detail. Electrolytic preconcentration can be combined with a variety of instrumental techniques. Special attention is given to stripping voltammetry, potentiometric stripping analysis, different combinations with atomic-absorption spectrometry, and the use of flow-through porous electrodes. It is pointed out that the electrolytic preconcentration technique deserves more extensive use as well as fundamental investigation.     

Determination of europium(III) in environmental samples using a flow injection analysis system with on-line preconcentration and spectrophotometric detection

A simple and accurate flow injection analysis system coupled with spectrophotometric detector was developed for preconcentration and determination of europium(III) in aqueous samples. The developed flow system includes a europium preconcentration step in a column packed with Amberlite XAD-4 resin impregnated with nalidixic acid at pH 7.0. The europium complex was desorbed from the resin by 0.1 mol L^?1 HCl and mixed with arsenazo-III solution (0.05 % solution in 0.1 mol L^?1 HCl) and taken to the flow through cell of spectrophotometer where its absorbance was measured at 661 nm. The optimum preconcentration system, chemical and FIA variables were investigated. The preconcentration factors obtained were 115 and 500, detection limits of 0.43 and 0.1 μg L^?1, sample throughputs of 40 and 10 were obtained for preconcentration time of 60 and 300 s respectively. The proposed system showed good precision and accuracy with relative standard deviation of 1.5 %. The method has been applied to the determination of europium(III) in real water samples and certified reference material IAEA-SL-1 (Lake sediment).     

Extraction and sorption preconcentration of rhenium with the use of 2-phosphorylphenoxyacetamides

Interfacial distribution of micro amount of ReO₄ ^- between aqueous solutions of mineral acids and solutions of 2-phosphorylphenoxyacetamides in dichloroethane has been studied. Stoichiometry of extracted complexes has been determined; the effect of HNO₃, HCl, and H₂SO₄ concentration in aqueous phase, extractant structure, and organic solvent nature on the efficiency of ReO₄ ^- ions transfer into organic phase has been considered. It has been shown that Re(VII) can be selectively recovered and concentrated with complexing sorbent obtained by the noncovalent binding of 2-[2-(diphenylphosphoryl)-4-ethylphenoxy]-N,N-dioctylacetamide on the surface of macroporous polymer Amberlite XAD7HP.     

Further study on a flow injection on-line multiplexed sorption preconcentration coupled with flame atomic absorption spectrometry for trace element determination

A further study on a newly developed flow injection (FI) on-line multiplexed sorption preconcentration (MSP) using a knotted reactor coupled with flame atomic absorption spectrometry (FAAS) was carried out to demonstrate its applicability and limitation for trace element determination. For this purpose, Cr(VI), Cu(II), Ni(II) and Co(II) were selected as the analytes, and detailed comparison was made between the MSP-FAAS and conventional FI on-line sorption preconcentration FAAS in respect to retention efficiency and linear ranges of absorbance versus sample loading flow rate and total preconcentration time. Introduction of an air-flow for removal of the residual solution in the KR after each sub-injection in the MSP procedure played a decisive role in the improvement of retention efficiency. The linearity of absorbance versus sample loading flow rate or total preconcentration time was extended to a more degree for the metal ions with less stability of their PDC (pyrrolidine dithiocarbamate) complexes than those with more stable PDC complexes. It seems that the MSP procedure behaves advantages beyond the inflection points in the diagrams of absorbance versus total preconcentration time and sample loading flow rate obtained by conventional (a single continuous) preconcentration procedure. With a sample loading flow rate of 6.0 ml min⁻¹ and a total preconcentration time of 180 s, the retention efficiencies were increased from 25, 46, 41 and 63% with a single continuous sorption preconcentration to 44, 78, 65 and 75% with a six sub-injection preconcentration procedure for Cr(VI), Co(II), Ni(II), and Cu(II), respectively. The detection limits were 0.40, 0.33, 0.31 and 0.26 μg l⁻¹ for Cr(VI), Co(II), Ni(II), and Cu(II), respectively. The precision (R.S.D.) for eleven replicate determination of 2 μg l⁻¹ Cr(VI), Co(II) and Ni(II), and 1 μg l⁻¹ Cu(II), was 2.1, 4.1, 2.6 and 1.7%, respectively.     

Mathematical modeling of flow and kinetics in a reactor for dilute-acid hydrolysis of cellulose particles

Amathematical model to simulate the dilute-acid hydrolysis process of cellulose particles is presented. In this model, the mass is treated as a mixture of different components. A test case is considered for which transport equations for components are developed and solved together with the momentum equation for the fluid flow. To solve the model equations, a commercially available flow solver was used. All input data were taken from previously published works. For the small static mixer considered as test geometry, the result, in terms of the conversion of the cellulose particles, was reasonable. With input parameters that are relevant to a plant-size reactor, the model can be used to predict the conversion of both cellulose and hemicellulose particles.     

Integrated continuous flow polymerase chain reaction and micro-capillary electrophoresis system with bioaffinity preconcentration

An integrated and modular DNA analysis system is reported that consists of two modules: (i) A continuous flow polymerase chain reaction (CFPCR) module fabricated in a high T(g) (150°C) polycarbonate substrate in which selected gene fragments were amplified using biotin and fluorescently labeled primers accomplished by continuously shuttling small packets of PCR reagents and template through isothermal zones as opposed to heating and cooling large thermal masses typically performed in batch-type thermal reactors. (ii) μCE (micro-capillary electrophoresis) module fabricated in poly(methylmethacrylate) (PMMA), which utilized a bioaffinity selection and purification bed (2.9 μL) to preconcentrate and purify the PCR products generated from the CFPCR module prior to electrophoretic sorting. Biotin-labeled CFPCR products were hydrostatically pumped through the streptavidin-modified bed, where they were extracted onto the surface of micropillars. The affinity bed was also fabricated in PMMA and was populated with an array of microposts (50 μm width; 100 μm height) yielding a total surface area of ～117 mm(2). This solid-phase extraction (SPE) process demonstrated high selectivity for biotinylated amplicons and utilized the strong streptavidin/biotin interaction (K(d) = 10(-15) M) to generate high recoveries. The SPE selected CFPCR products were thermally denatured and single-stranded DNA released for injection into a 7-cm-long μCE channel for size-based separations and fluorescence detection. The utility of the system was demonstrated using Alu DNA typing for gender and ethnicity determinations as a model. Compared with the traditional cross-T injection procedure typically used for μCE, the affinity pre-concentration and injection procedure generated signal enhancements of 17- to 40-fold, critical for CFPCR thermal cyclers due to Taylor dispersion associated with their operation.     

Automatic flow system for evaluation of polystyrene-divinylbenzene sorbents applied to preconcentration of phenolic pollutants

In this work, an evaluation of commercially available polystyrene-divinylbenzene sorbents for solid-phase extraction (SPE) of eleven phenolic compounds is intended. Considering the particle size and cross-linking degree, Amberlite XAD-4 (commercial or grounded), Macronet MN-200 and Lichrolut EN were tested. The SPE protocol was performed by an automatic system, providing repeatable experimental conditions for assessment of sorbent capacity, breakthrough volume and enrichment factor (EF). A positive correlation between EF and log?K _ow was found for Amberlite XAD-4 while a negative correlation was observed between EF and molecular weight of analyte for Macronet MN-200 and for Lichrolut EN. This indicates a prevalence of hydrophobic interactions or molecular exclusion depending upon the polymer cross-linking degree. Despite the similar repeatability (RSD?<?4.7%, n?>?6) and recovery values attained (97.6–102.7%, using 50?mL of sample) for all sorbents, Lichrolut EN is the best choice for analytical application as higher EF and lower LOD values (between 18 and 207?ng) were attained for this sorbent.