多孔PMP聚合物薄膜微结构控制

将二氧化硅(SiO2)微球为模板材料分散在聚-4-甲基-1-戊烯(PMP)溶液中,通过对流自组装方法将其涂覆于基片上,经过热致相分离(TIPS)过程形成含SiO2微球模板的PMP薄膜,然后通过氢氟酸(HF)溶液腐蚀除去SiO2微球,获得了具有规则多孔结构的PMP聚合物薄膜。采用扫描电子显微镜(SEM)对含SiO2微球的PMP薄膜以及除去SiO2微球后的PMP多孔薄膜的微结构进行了表征。研究结果表明:SiO2微球在聚合物中呈有序排列,腐蚀除去SiO2微球后PMP薄膜有效复制了SiO2微球形成的有序结构,形成了有序多孔PMP薄膜。     

聚甲基丙烯酸甲酯光子晶体的生长和结构分析

金属/半导体基光子晶体有重大的国防应用价值,其生长技术的核心是设计合适的方法将聚甲基丙烯酯甲酯(PMMA)微球组装成光子晶体。在目前垂直沉积法的基础上,通过控制甲基丙烯酸甲酯(MMA)和偶氮引发剂的反应,使用等温蒸发工艺开发了光子晶体的可控垂直沉积(CVD)技术。实验合成了高度单分散的PMMA微球,并将PMMA微球组装成了光子晶体;对试样进行扫描电镜研究发现,晶体内部排列有序度很高,表面层很完美平整,在3μm×5μm的有序区内仅有两个点缺陷;使用直径分别为294nm和345nm的PMMA微球,沉积出具有规则的周期性密堆积结构的光子晶体,试样的完美有序区范围在20μm以上。实验发现,在可控垂直沉积法的晶体生长过程中,光子晶体的生长方式为连续生长,生长界面为粗造界面。     

氧化钨二维微米球腔阵列对聚苯胺电致变色的影响

采用气/液界面自组装方法制备规整排列的聚苯乙烯微球二维单层结构,以此为模板,采用电化学沉积法在电极表面构筑了有序的氧化钨微球腔阵列,进一步在氧化钨球腔内电化学沉积聚苯胺,采用吸收光谱研究了电极表面球腔阵列结构对聚苯胺电致变色行为的影响.     

光纤圆柱曲面基底胶体微球的自组装

以标准单模光纤包层的外表面作为基底,通过改进的恒温蒸发对流引导合理控制溶剂蒸发温度和液体表面下降的速度,使用垂直沉积法在其曲面圆柱型基底涂覆三维二氧化硅胶体晶体。单模光纤垂直插入二氧化硅胶体溶液中,处于圆形容器的中心,在毛细力的驱动下胶体微球在光纤外表面形成三维的胶体晶体薄膜。实验所用二氧化硅微球平均粒径为390 nm,晶体生长时间仅为12 h。用扫描电子显微镜(SEM)分析了样品的表明形貌:确定了样品表面面心立方结构的[111]和[100]两种晶向排列,同时发现了[100]晶向之间有规律的[111]晶向排列的交叉图案。对胶体微球不同的晶向排列以及交叉图案进行了定性的分析和讨论。     

毛细微模塑法制作聚合物微球的有序结构

用毛细微模塑法在玻璃基片上组装了聚苯乙烯微球紧密的有序阵列 .扫描电镜观察了组装后的微球排列 .结果表明 ,在毛细通道的出口端 ,聚苯乙烯的微球堆积得紧密有序 .毛细通道的尺寸 ,环境温度和聚合物微球乳液的浓度是毛细微模塑法的主要影响因素 .     

纳米Pt/MgO催化剂的表征和催化性能

"用浸渍法制备了Pt/MgO催化剂,采用X射线衍射、X射线光电子能谱、透射电子显微镜和程序升温表面反应等技术对反应前后的催化剂进行了表征．甲烷部分氧化制备合成气的反应被用来考察催化剂的催化活性和稳定性．TEM结果显示活性组分Pt粒子的尺寸小于10 nm,而载体MgO的晶粒大小在50~200 nm．在固定床微反应器上进行．在800 ℃时,Pt/MgO催化剂表现了非常高的POM催化活性和稳定性,甲烷转化率和合成气的选择性在120 h内保持稳定．活性组分Pt以金属状态存在于载体的表面上,其存在状态和分散状态都很     

三维有序二氧化锰大孔材料的模板技术合成及表征

以单分散SiO2 胶态晶体球形成的三维有序结构为模板 ,利用胶体晶模板技术合成了三维长程有序的二氧化锰大孔材料 .通过X射线粉末衍射 (XRD)和扫描电子显微镜 (SEM)对产物进行了表征 .其中XRD数据显示所得产物为纯四方相二氧化锰 .SEM结果表明 ,所合成的二氧化锰大孔材料孔大小均匀 ,空间排列高度有序 ,很好地复制了SiO2 胶态晶体球的自组装方式 .此外 ,对三维有序二氧化锰大孔材料的合成过程进行了分析 ,研究了前体填充次数对产物孔结构的完整性和有序性的影响 ,还发现产物孔径的收缩存在异常现象 .     

旋涂法快速制备双层二元胶体微球有序薄膜

以较大粒径的聚苯乙烯或SiO₂胶体微球的单层有序薄膜作基膜,较小粒径的SiO₂微球作第二层,用分步旋涂法快速制备了二元双层胶体微球复合有序薄膜.膜中小粒径微球与大粒径微球的粒径比γ=020—056,大粒径与小粒径微球的排列方式可表示为LS_x（x=1,2,…,13）.旋涂速度、旋涂时间、微球悬浮介质的黏度、悬浮液中微球的数密度、旋涂衬底的可润湿性等因素均会影响旋涂组装胶粒薄膜的质量.在旋涂衬底能够被胶体微球悬浮介质完全润湿的前提下,适宜的胶体微球数密度、旋涂速度、旋涂时间是旋涂组装有序薄膜的必要条件. 关键词： 复合有序薄膜 分步旋涂 胶体微球模板     

基于电泳法和磁控溅射技术制备金纳米阵列

采用纳米球刻蚀技术中的电泳法设计了3组对照实验,通过控制电压、悬浮液的体积分数和基板正负极性,得到电泳法制备纳米球掩膜板的最佳条件,制备出排布均匀的纳米球单层密堆积结构的掩膜板.采用磁控溅射技术在掩膜板上沉积金薄膜,去除纳米球掩模板,通过扫描电子显微镜观察到周期排列的三角形棱台状金纳米颗粒阵列.测量其吸收光谱,可观察到表面等离子体共振吸收峰.     

毛细管内嵌微球谐振腔的温度传感特性研究

对基于毛细管的微球谐振腔耦合器件的耦合机理与温度传感特性进行了研究。微球支持较多的高阶模式,易与石英毛细管模式满足相位匹配条件,因此微球回音壁模式会被激发。使用钛酸钡微球进行了温度传感实验,为进一步提升传感的灵敏度,采用聚甲基丙烯酸甲酯（polymethyl methacrylate,PMMA）微球进行了温度传感实验。实验结果表明,PMMA微球温度传感灵敏度可达83.9 pm/℃,约为钛酸钡微球温度传感灵敏度的8倍,在提升温度传感灵敏度方面具有重要作用。     

Synthesis of nanoporous silicon carbide ceramics by thermal evaporation process

New nanoporous β-SiC ceramics were synthesized by a simple thermal evaporation method with commercial silicon powder and activated carbon fragments. The results of scanning electron microscopy, transmission electron microscopy, energy dispersive spectroscopy and X-ray diffraction indicated that the microstructure of the β-SiC nanoporous ceramics was uniform and consistent with the pore size of 50-100 nm. The β-SiC nanocrystal grains of 50-200 nm were accumulated together to form a nanopore network. The formation mechanism was attributed to a template synthesis process, in which activated carbon fragments were employed as the template and they reacted with vaporized silicon through a vapor-solid way.     

Magnesium oxide nanocrystals via thermal decomposition of magnesium oxalate

The present work reports the synthesis of magnesium oxide (MgO) nanocrystals via a thermal decomposition route and the study of physicochemical properties of products. The MgO nanocrystals were prepared from magnesium oxalate powders as precursor. Transmission electron microscopy (TEM) analysis demonstrated MgO nanocrystals with an average diameter of about 20−25 nm. The products were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), selected area electronic diffraction (SAED), and Fourier transform infrared (FT-IR) spectroscopy. Optical absorption and photoluminescence emission properties of MgO nanocrystals were investigated.     

Template synthesis of nanostructured silica with hollow core and mesoporous shell structures

Silica capsules with hollow macroporous core–mesoporous shell (HCMS) were synthesized through template-assisted replication of submicrometer-size polystyrene spheres as templates. The silica mesoporous shell exhibited highly ordered hexagonal structure as confirmed by X-ray diffraction pattern and TEM image. The pore diameter and BET surface area of this sample were found to be 2.1 nm and 1387 m²/g, respectively.     

Nanoporous AlN particles production from a solid-state metathesis reaction

This paper reports that nanoporous AlN particles are synthesized from solid-state metathesis reactions using AlCl₃ and Mg₃N₂ as reactants. The samples are characterized by x-ray diffraction (XRD), transmission electron microscopy (TEM), selected area electron diffraction, high-resolution transmission electron microscopy (HRTEM), ultraviolet--visible (UV--vis) absorption spectroscopy and Raman spectroscopy. The results show that samples with walls 10 nm in thickness and pores between 10 nm and 100 nm in diameter were produced successfully from these reactions, and their band gap and vibration modes agree with those of AlN bulk crystal.     

Influence of colloidal templates on the impedance spectroscopic behaviour of Pr0.7Sr0.3Fe0.8Ni0.2O3 for solid oxide fuel cell applications

The creation of porous materials with three-dimensional periodicity has been identified as being of potential interest for increasing the overall performance of solid oxide fuel cells (SOFC). In this work, we have investigated the formation of pore systems in the nanometer scale by replicating colloidal templates. Templating methods have been used to prepare iron-nickel-based perovskite Pr_0.7Sr_0.3Fe_0.8Ni_0.2O₃ material with nanoporous microstructure. Polymethyl methacrylate (PMMA), polystyrene (PS) and polycarboxylate (PC) microspheres with different diameters were used as pore formers. These samples were synthesized and characterized by thermogravimetric analysis, inductively coupled plasma atomic emission spectroscopy (ICP-AES), X-ray diffraction, transmission electron microscopy and field emission scanning electron microscopy. The polarization resistance of the materials was studied by Electrochemical Impedance Spectroscopy. The study demonstrated that templated porosity is maintained and highly influences on the impedance spectroscopic behaviour, being the material synthesized with policarboxylate microspheres the most interesting of the three used templates for SOFC applications.     

沉积法自组装三维有序的Eu(DBM)3Phen/SiO2胶体球

采用修饰的St ber法合成了300 nm的Eu(DBM)3Phen/SiO2胶体杂化球,并通过沉积法将这种胶体杂化球组装成厚度为5 mm,面积为12 cm2的三维有序结构。通过扫描电子显微镜观察发现这些胶体球在垂直于烧杯底面的所有层面中都显示了立方密堆积的结构。元素分析进一步证实了荧光分子被包埋在SiO2胶体球中。在355 nm的激发下,这种三维有序结构具有铕离子的特征发射。     

Co3O4纳米花的合成及其磁性

通过水热和热处理的方法，制备了产物Co3O4纳米花. 用X射线粉末衍射、场发射扫锚电镜、透射电镜和红外光谱等手段对产物进行了表征. 结果表明，产物纳米花是由大量的Co3O4纳米须组成，纳 米须的直径为20?40 nm，长度为100?500 nm，具有纳米孔结构，比表面积约为34.61 m2/g. 磁性测量表明，在零场冷却条件下，产物主要表现为反铁磁性；在加场冷却条件下，闭锁温度约为34K时，产物主要表现为铁磁性．     

ZnO spheres and nanorods formation: their dependence on agitation in solution synthesis

ZnO nanostructures including nanorods, dense, and partially hollow spheres were synthesized via a solution synthesis method with temperature ranging from 65 to 95 °C. Scanning electron microscopy (SEM) revealed that the diameter of the spheres is in the range of 200–500 nm. Transmission electron microscopy (TEM) showed that some of the spheres are hollow or partially hollow. Powder X-ray Diffraction (XRD) and TEM-Selected area electron diffraction (SAED) analysis showed that the spheres consist of polycrystalline nanoparticles. It was found for the first time that the agitation during the synthesis plays a critical role on morphology of the ZnO nanostructures formed in solution. The oriented attachment of nanocrystals without agitation during the synthesis could guide the nanocrystals to form an ordered nanorod structure. However, the disordered aggregation of the nanocrystals under shear force resulted in a spherical morphology. It was also found that the composition of spheres is different from that of nanorods: the spheres consist of both ZnO and Zn(OH)₂, but nanorods consist of single-crystal ZnO only. Zn(OH)₂ presented in the spheres could decompose to ZnO by calcination, resulting in the formation of hollow spheres.     

Synthesis of nanostructured polymer materials with different morphologies: Nanoporous ordered networks and hollow capsules

Nanostructured polymer materials with interesting morphological variation, which include three dimensionally interconnected uniform nanoporous network arrays (volume- and surface-templated ordered arrays) and hollow core spheres were synthesized by inducing different polymerization process of phenol and formaldehyde as a precursor over silica templates (ordered silica colloidal crystals or individual silica particles). The pore sizes of the resulting nanostructured polymer materials can be easily controlled by monitoring the sizes of silica spheres, while their morphologies were modulated by controlling the initiation sites of the acid-catalyzed condensation reaction of the same polymer precursor and by modifying silica templates.     

Coating zinc oxide submicron crystals on poly(methyl methacrylate) chips and spheres via ultrasound irradiation

Ultrasound irradiation is used for anchoring zinc oxide submicron crystals with a main diameter and length of 280 nm and 470 nm, respectively, onto the surface of poly(methyl methacrylate) PMMA chips (2 mm diameter), and zinc oxide crystals with a mean diameter and length of 150 nm and 230 nm, respectively, onto the surface of the PMMA spheres (1–10 μm). The zinc oxide crystals were obtained by sonochemical irradiation of a mixture containing the PMMA, zinc (II) acetate dihydrate, ethanol, water, and 24 wt.% aqueous ammonia for 2 h, yielding a PMMA–zinc oxide composite. By controlling the atmosphere and reaction conditions, we could achieve well-adhered zinc oxide crystals on the surface of poly(methyl methacrylate). The resulting zinc oxide–PMMA composite was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), energy-dispersive X-ray analysis (EDX), high-resolution scanning electron microscopy (HRSEM), and photoluminescence (PL) spectroscopy. The zinc oxide-deposited PMMA chips (loaded with 0.03–1.0 wt.% ZnO) were successfully homogenized in melt by extrusion and then injection molded into small, disc-shaped samples. These samples were analyzed with respect to their directional spectral optical properties in UV, Vis and IR spectroscopy.