Valence band XPS and FT-IR evaluation of thermal degradation of HVAF thermally sprayed PEEK coatings

Coatings of PEEK (poly-ether-ether-ketone) have been produced on stainless steel 304 using the High Velocity Air Fuel (HVAF) thermal spray technique. These coatings were produced using 50 and 100 mm nozzle lengths with 200, 300 and 400 mm gun to substrate distances. The thermal degradation of the PEEK during the production of the coatings was assessed with valence band X-ray Photoelectron Spectroscopy (XPS) and attenuated total reflectance Fourier Transform Infrared Spectroscopy (ATR FT-IR). Valence band XPS shows that in general there is minimal degradation of the PEEK during the HVAF thermal spraying process. The FT-IR results show that at the 200 mm gun to substrate (standoff) distance for both nozzle lengths there is more surface degradation of the PEEK coating than at the longer gun to substrate distances. Specifically absorption bands appeared at 2918 and 2850 cm⁻¹, which correspond to alkane -CH₂- asymmetric stretching modes. The reduction of the 1250 cm⁻¹ band as compared with the 1220 cm⁻¹ band, both representing the stretching modes of the ether bonds in PEEK suggests that the degradation occurs at only one of the ether bonds. The phenyl C-H vibration at 673 cm⁻¹ was split for coatings produced at gun-substrate distance of 200 and 300 mm. This indicates a structural change in the phenyl ring possibly indicating a change in the extent of crystallinity of the PEEK polymer.     

FTIR study of water clusters in water–triethylamine solutions

The FTIR study presented in this work, on water dissolved in triethylamine (TEA), reveals the formation of water clusters in the TEA liquid phase at tenths of water molar concentrations. In the OH stretching region, the FTIR spectra of water in TEA show, at high frequencies, a narrow band at 3682 cm⁻¹ and, at low frequencies, a wide band that can be resolved into four peaks with maxima at 3249 cm⁻¹, 3348 cm⁻¹, 3440 cm⁻¹ and 3545 cm⁻¹. The results have been rationalised assuming the formation of clusters containing tens of three- and four-coordinated water molecules. TEA molecules surrounding the clusters are hydrogen bonded to one OH of the water molecules at the surface, leaving dangling protons. Further, the analyses of the spectra suggest that, in the used range, the water cluster mean size does not depend strongly on the water concentration.     

FT-IR microscopic imaging of calcified deposit of rotator cuff tendonitis: A pilot study and a randomised identification of the compositional components after extrusion from tendon to muscle

Fourier transform infrared (FT-IR) microspectroscopy with mapping system was applied to identify and evaluate what difference in the distribution and compositional components of the calcified deposit of rotator cuff tendonitis after dislocation from tendon to muscle. A 49 year-old female patient suffered from severe shoulder pain was enrolled in this study. Diagnostic high-resolution ultrasonography (HRUS) was initially carried out to verify the calcific tendonitis. The calcified deposits were then examined by histopathologic assessment and FT-IR microspectroscopy. Diagnostic HRUS reveals that the calcified deposits were observed in the subscapularis tendon and infraspinatus muscle of the shoulder for this patient. FT-IR microspectroscopic imaging results clearly indicate that both IR spectra of the calcified deposits in tendon and muscle were almost the same as that of the IR spectrum of hydroxyapatite except the peak at 873 cm⁻¹. It is also found that the peak intensity at 1030 cm⁻¹ for tendon sample was somewhat more intense than that of the peak at 1031 cm⁻¹ for muscle sample, implying that the calcified sample in the tendon seems to be mature than that in the muscle. The second-derivative IR spectra of two calcified samples exhibit two specific sharp peaks at 880 and 872 cm⁻¹, indicating that the type A and type B carbonated apatites were markedly co-existed in both calcified deposits of tendon and muscle even the calcified deposit was dislocated from tendon to muscle. These carbonated apatites presented in the calcified deposits of either tendon or muscle of the shoulder were also consistent with the nodular or nodular nodular-cystic morphology of calcified plaque of the shoulder after HRUS examination.     

Vibrational spectra and reinvestigation of the crystal structure of a polymeric copper(II)-orotate complex, [Cu(μ-HOr)(H2O)2]n: The performance of new DFT methods, M06 and M05-2X, in theoretical studies

The crystal and molecular structure of a polymeric Cu(II)-orotate complex, [Cu(μ-HOr)(H₂O)₂]_n, has been reinvestigated by single crystal X-ray diffraction. It is shown that several synergistic interactions: two axial Cu-O interactions; intramolecular and intermolecular hydrogen bonds; and π-π stacking between the uracil rings contribute to the stability of the crystal structure. The Raman and FT-IR spectra of the title complex are reported for the first time. Comprehensive theoretical studies have been performed by using three unrestricted DFT methods: B3LYP; and the recently developed M06, and M05-2X density functionals. Clear-cut assignments of all the bands in the vibrational spectra have been made on the basis of the calculated potential energy distribution, PED. The very strong Raman band at 1219 cm⁻¹ is diagnostic for the N1-deprotonation of the uracil ring and formation of the copper-nitrogen bond, in this complex. The Cu-O (carboxylate) stretching vibration is observed at 287 cm⁻¹ in the IR spectrum, while the Cu-N (U ring) stretching vibration is assigned to the strong Raman band at 263 cm⁻¹. The molecular structure and vibrational spectra (frequencies and intensities) calculated by the M06 functional method are very similar to the results obtained by the B3LYP method, but M06 performs better than B3LYP in calculations of the geometrical parameters and vibrational frequencies of the interligand O-H?O hydrogen bonding. Unfortunately, the M05-2X method seriously overestimates the strength of interligand hydrogen bond.     

Thermal properties and stability of cassava starch films cross-linked with tetraethylene glycol diacrylate

The thermal stability of starch cross-linked with tetraethylene glycol diacrylate was studied under nitrogen atmosphere by thermogravimetry (TG) and infrared spectroscopy (FTIR). The cross-linking reaction was confirmed by the increase in intensity of the absorption band at ca. 3330 cm⁻¹ indicating the reinforcement of hydrogen bonds and the appearance of a new band at 1726 cm⁻¹ associated with the carbonyl group of the cross-linking agent. After cross-linking the solubility of starch in water decreased to the range 9%-16%. The thermogravimetric curves of pure and cross-linked starches showed an initial stage of degradation (up to ca. 150 °C) associated with the loss of water. The main stage of degradation occurred in the range 250-400 °C corresponding to ca. 60%-70% mass loss. The activation energy (E) for the degradation process increased from 145 kJ mol⁻¹ (pure starch) to 195 kJ mol⁻¹ and 198 kJ mol⁻¹ for starch treated for 60 min by UV (30 °C) and at 90 °C, suggesting high stability after cross-linking. A higher value (240 kJ mol⁻¹) was obtained for starch treated by UV for 120 min. The main volatile products determined by FTIR which correspond to hydrocarbons and carbonyl groups are apparently associated with the scission of weak bonds in the chain (probably branched groups) and the scission of stronger bonds (glycosidic linkages), respectively.     

Vibrational and scanning electron microscopy study of the mordenite modified by Mn, Co, Ni, Cu, Zn and Cd

The mordenite samples loaded with divalent nitrates of Mn, Co, Ni, Cu, Zn and Cd were investigated using FTIR and scanning electron microscopy (SEM) methods. It was found from FTIR spectra that in 3000-4000 cm⁻¹ region of mordenite samples with similar water concentration ions, Mn²⁺, Co²⁺, Cu²⁺, and Zn²⁺ tend to break hydrogen bonds formed between water molecules and zeolite framework, whereas Ni²⁺ and Cd²⁺ accommodate to hydrogen bonds. From SEM results it was concluded, that ions Mn²⁺, Co²⁺, Zn²⁺ form innersphere complexes with oxygens from Brönsted acid sites, whereas Ni²⁺ and Cd²⁺ associate with Brönsted acid sites without exchange of protons.     

Shape of the proton potential in an intramolecular hydrogen-bonded system. Part II

The crystals of 5,5′-dibromo-3-diethylaminomethyl-2,2′-biphenol N-oxide were studied by X-ray and FT-IR spectroscopy. Within this molecule two short OHO intramolecular hydrogen bonds are formed. The NO?H⁺?O⁻ bond between the OH and the N-oxide groups is very strong, of 2.419(7) Å between the oxygen atoms. The proton potential of this hydrogen bond is flat, broad and has probably no barrier—consequently it could not be located from X-ray diffraction data. The other hydrogen bond formed between two hydroxyl groups appears asymmetrical from FT-IR spectra, and shows also relatively limited proton polarizability. The molecular conformation is non-planar, due to strong overcrowding effect between the oxygen atoms involved in the hydrogen bonds.     

Vibrational analysis of 4-amino pyrazolo (3,4-d) pyrimidine A joint FTIR, Laser Raman and scaled quantum mechanical studies

The FTIR and Laser Raman spectra of 4-amino pyrazolo (3,4-d) pyrimidine have been measured in the regions 4000–400 cm⁻¹ and 3500–100 cm⁻¹, respectively. Utilizing the observed FTIR and Laser Raman data, a complete vibrational assignment and analysis of the fundamental modes of the title compound were carried out. The vibrational frequency which were determined experimentally are compared with those theoretically from force field calculation based on ab initio HF/6−311+G**(d,p) and standard B3LYP/6−311+G**(d,p) methods and basis set combinations for optimized geometries. The observed FTIR and Laser Raman vibrational frequencies were analysed and compared with the theoretically predicted vibrational frequencies. The assignments of bands to various normal modes of the molecules were also carried out. A detailed interpretation of the infrared and Raman spectra of 4-amino pyrazolo (3,4-d) pyrimidine [4AP(3,4-D)P] is also reported based on total energy distribution (TED). The calculated HOMO and LUMO energies shows that charge transfer occur within the molecule. The theoretical FT-IR and FT-Raman spectra for the title molecule have also been constructed.     

Synthesis and characterization of polyaniline nanoparticles in the presence of magnetic field and samarium chloride

A new and economical method of preparing polyaniline (PANI) nanoparticles will be introduced in this article. Compared with conventional methods, this method is much more simple and convenient. Scanning electron microscope (SEM) shows that the diameter of particles are between 30 and 50 nm, which is in good agreement with the results of a transmission electron microscope (TEM). Polyaniline/SmCl₃/Bp, polyaniline/SmCl₃ and polyaniline/HCl were prepared in a solution containing 1.0 mol dm⁻³ aniline, 1.0 mol dm⁻³ HCl with and without 0.5 mol dm⁻³ SmCl₃, in the presence and in the absence of a magnetic field, respectively. Their conductivity, UV-vis spectra, FTIR spectra, X-ray diffraction (XRD) and thermogravimetric analysis (TGA) were investigated. Changes in UV-vis and FTIR spectra indicate a strong interaction between Samarium ions (SmCl₃) and polyaniline chains. The conductivity of PANI depends on magnetization and concentration of Sm³⁺. Polyaniline/SmCl₃/Bp has the higher degree of crystallinity than that of polyaniline/HCl.     

Effect of sodium hydroxide pre-treatment on the optical and structural properties of lyocell

Lyocell is a type of regenerated cellulose. Fibres spun from cellulose solution in N-methylmorpholine-N-oxide hydrate consist of crystalline cellulose II and amorphous cellulose. Lyocell fabrics were treated with aqueous sodium hydroxide solution (NaOH) to study the influence of alkali on optical and structural properties. It was observed that sodium hydroxide treatment causes the density, orientation and crystallinity of lyocell fibre to decrease with increasing sodium hydroxide concentration, a corresponding decrease in tensile strength is also observed. The greatest change in fibre properties occurs between 3.0 and 5.0 mol dm⁻³ NaOH. This is attributed to the onset of formation of Na-cellulose II at 3.0 mol dm⁻³ NaOH; a fully formed Na-cellulose II structure is expected above 6.8 mol dm⁻³ NaOH. Formation of Na-cellulose II causes plasticization of the lyocell fibres as both inter- and intra-molecular hydrogen bonds are broken by these higher sodium hydroxide concentrations.     

Electrospinning nanosuspensions loaded with passivated Au nanoparticles

Aqueous polyethylene oxide (PEO) solutions (2 MDa, 2-5 wt %) with or without citrate passivated Au nanoparticles (5.7×10⁻⁷ wt %) have been electrospun, producing fibres with diameters from 290 μm to 55 nm. The incorporation of nanoparticles suppresses the diameter of the fibres and increases the degree of crystallinity. Such nanocomposite fibres are of interest as self-assembled templates for bottom-up fabrication methodologies.     

FTIR and fluorescence studies on the ground and excited state hydrogen-bonding interactions between 1-methylindole and water in water–triethylamine mixtures

The ground and excited state π-hydrogen-bonding interactions between 1-methylindole, MI, and water have been investigated in water–triethylamine, water–TEA, mixtures. FTIR measurements performed on the OH stretching bands of the water–TEA clusters show that, upon MI addition, the typical bands of the water–TEA system at 3348 cm⁻¹, 3440 cm⁻¹, 3545 cm⁻¹ and 3682 cm⁻¹ diminish, whereas two new absorption bands at 3316 cm⁻¹ and 3654 cm⁻¹ grow up. These spectral changes have been rationalised assuming the formation of only one 1:1 water–MI complex, in which the dangling protons in the water–TEA clusters are hydrogen bonded to the π-cloud of the MI aromatic ring. Steady state and time resolved fluorescence measurements provide additional proofs on the ground state formation of a fluorescent OH ? π hydrogen bonded complex. The relevance that the present and the previously reported results could have on the indole ring photophysics is discussed.     

Fabrication of Pt/polypyrrole hybrid hollow microspheres and their application in electrochemical biosensing towards hydrogen peroxide

Pt/polypyrrole (PPy) hybrid hollow microspheres were successfully prepared by wet chemical method via Fe₃O₄ template and evaluated as electrocatalysts for the reduction of hydrogen peroxide. The as-synthesized products were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectra (XPS), X-ray diffraction (XRD), inductive coupled plasma emission spectrum (ICP) and Fourier-transform infrared spectra (FTIR) measurements. The results exhibited that ultra-high-density Pt nanoparticles (NPs) were well deposited on the PPy shell with the mean diameters of around 4.1 nm. Cyclic voltammetry (CV) results demonstrated that Pt/PPy hybrid hollow microspheres, as enzyme-less catalysts, exhibited good electrocatalytic activity towards the reduction of hydrogen peroxide in 0.1 M phosphate buffer solution (pH = 7.0). The composite had a fast response of less than 2 s with linear range of 1.0-8.0 mM and a relatively low detection limit of 1.2 μM (S/N = 3). The sensitivity of the sensor for H₂O₂ was 80.4 mA M⁻¹ cm⁻².     

Detection and quantitative determination of the crystalline phase in poly(vinyl alcohol) cryogels by ATR FTIR spectroscopy

The molecular structure of poly(vinyl alcohol) in its cryogels obtained via a single freeze-thaw cycle of aqueous solutions of the polymer is investigated by ATR FTIR spectroscopy. By means of Fourier deconvolution and spectral subtraction, methods, it is found that the spectra of cryogels contain a hidden crystallinity band at 1144 cm^?1 due to poly(vinyl alcohol). For poly(vinyl alcohol) films crystallized at different temperatures, a quantitative relationship is established between the relative intensity of absorption at a frequency of 1144 cm^?1 in the spectra of the polymer and its degree of crystallinity estimated via wide-angle X-ray diffraction. In terms of this relationship, the degree of crystallinity of poly(vinyl alcohol) in the cryogels is determined from their ATR FTIR spectra. This parameter is found to be 6, 10, and 14% for the cryogels with PVA concentrations of 9, 17, and 29%, respectively. The obtained data suggest that the formation of the cryogels is accompanied not only by the appearance of polymer crystallites but also by a change in the system of hydrogen bonds between the polymer and water.     

Vibrational assignment of the spectral data and thermodynamic properties of 2-chloro-4-fluorobenzophenone using DFT quantum chemical calculations

The FT-Raman (3500-100 cm⁻¹) and FT-IR (4000-450 cm⁻¹) spectra of 2-chloro-4-fluorobenzophenone were recorded in the solid phase. Density functional theory calculations with B3LYP/6-31G (d, p) basis set was used to determine the ground state molecular geometries (bond lengths and bond angles), harmonic vibrational frequencies, infrared intensities and Raman activities of this compound. Potential energy distributions (PEDs) and normal modes, for the spectral data computed at B3LYP/6-31G (d, p) level, have also been obtained from force-field calculations. The wavenumbers found after scaling of the force field showed very good agreement with the experimentally determined values. A comparison of the theoretical spectra and experimental FT-IR and FT-Raman spectra of the title molecule has been made and full vibrational assignments of the observed spectra have been proposed. On the basis of vibrational analyses, the thermodynamic properties of title compound at different temperatures have been calculated.     

Structural changes in thermal-induced polyacrylonitrile gel under uniaxial drawing

The influences of uniaxial drawing on the different structural scales in thermal-induced polyacrylonitrile (PAN) gel were studied. The results of atomic force microscopy (AFM) and swelling tests indicated that the drawn PAN gels had more compact structure with less solvent contained. Besides, some microphase separations occurred in the highly drawn gel and caused the gel to become more porous, as verified by the results from differential scanning calorimetry (DSC). The wide-angle X-ray diffraction (WAXD) results confirmed that drawing induces chain orientation and partial crystallization in the thermal-induced PAN gels, and higher draw ratio generated greater structural changes in the gels. It was also found from the tensile stress relaxation of the gels that the crosslinks in the gel increased with the draw ratio. In Fourier transform infrared (FTIR) spectra, the blue shift in wave numbers of two absorption peaks (3200-3700 cm⁻¹ and around 2244 cm⁻¹), and a gradually disappearing peak at 1036 cm⁻¹ all indicated the weakening hydrogen bonding between the PAN molecular chains and dimethyl sulfoxide (DMSO) molecules during the drawing process.     

1064 nm dispersive multichannel Raman spectroscopy for the analysis of plant lignin

The mixed phenylpropanoid polymer lignin is one of the most abundant biopolymers on the planet and is used in the paper, pulp and biorenewable industries. For many downstream applications, the lignin monomeric composition is required, but traditional methods for performing this analysis do not necessarily represent the lignin composition as it existed in the plant. Herein, it is shown that Raman spectroscopy can be used to measure the lignin monomer composition. The use of 1064 nm excitation is needed for lignin analyses since high fluorescence backgrounds are measured at wavelengths as long as 785 nm. The instrument used for these measurements is a 1064 nm dispersive multichannel Raman spectrometer that is suitable for applications outside of the laboratory, for example in-field or in-line analyses and using remote sensing fiber optics. This spectrometer has the capability of acquiring toluene/acetonitrile spectra with 800 cm⁻¹ spectral coverage, 6.5 cm⁻¹ spectral resolution and 54 S/N ratio in 10 s using 280 mW incident laser powers. The 1135–1350 cm⁻¹ and 1560–1650 cm⁻¹ regions of the lignin spectrum can be used to distinguish among the three primary model lignin monomers: coumaric, ferulic and sinapic acids. Mixtures of the three model monomers and first derivative spectra or partial least squares analysis of the phenyl ring breathing modes around 1600 cm⁻¹ are used to determine sugarcane lignin monomer composition. Lignin extracted from sugarcane is shown to have a predominant dimethoxylated and monomethoxylated phenylpropanoid content with a lesser amount of non-methoxylated phenol, which is consistent with sugarcane's classification as a non-woody angiosperm. The location of the phenyl ring breathing mode peaks do not shift in ethanol, methanol, isopropanol, 1,4 dioxane or acetone.     

Solid sampling Fourier transform infrared determination of Mancozeb in pesticide formulations

A series of approaches have been assayed for FTIR determination of Mancozeb in several solid commercial fungicides using different calibration strategies. The simplest procedure was based on the use of the ratio between the absorbance of a characteristic band of Mancozeb and that of a KSCN internal standard measured in the FTIR spectra obtained from KBr pellets. It was employed the quotient between peak height absorbance values at 1525 cm⁻¹ for Mancozeb and 2070 cm⁻¹ for KSCN. In these conditions a precision as relative standard deviation (RSD) of 0.6% and a relative accuracy error of 0.8% (w/w) were found. For complex formulations, containing other compounds with characteristic absorption bands at different wavenumbers than Mancozeb, one of them was used as internal reference being employed the standard addition approach. In this case, the Mancozeb bands at 1525 cm⁻¹ or at 1289 cm⁻¹ were employed, being used the ferrocyanide band at 2075 cm⁻¹ as internal reference. RSD values between 0.7-1.4% and a relative accuracy error of 3% (w/w) were found. A third strategy was based on the use of partial least squares (PLS) calibration. A reference set was prepared mixing Mancozeb, Kaolin, Cymoxanil and KBr, being predicted the Mancozeb concentration in pesticide formulations by using the quotient between absorbance bands of Mancozeb and those of Cymoxanil. In these conditions a relative accuracy error of 0.6% (w/w) and a relative standard deviation of 1.3% were found.     

Polyaniline and polypyrrole: A comparative study of the preparation

Aniline and pyrrole have been oxidized with ammonium peroxydisulfate in aqueous solutions, in the presence of equimolar quantities of hydrochloric acid. The oxidation of pyrrole was faster; the induction period typical of aniline oxidation was absent in the case of pyrrole. As the proportion of oxidant-to-monomer molar concentration increased up to 1.5, the yield increased in both cases. Similarities between the two oxidations are illustrated and discussed. The oxidant-to-monomer molar ratio 1.25 is proposed to be the optimum stoichiometry, in the accordance with the data published in the literature. The conductivities of the polymers prepared were only slightly dependent on the oxidant-to-monomer ratio in the range 0.3-1.5, and were of the order of 10⁰ S cm⁻¹ for polyaniline and ∼10⁻²-10⁻¹ S cm⁻¹ for polypyrrole. Outside this interval, the conductivity of both polymers was reduced. Polyaniline having conductivity ∼10 S cm⁻¹ was produced in solutions of phosphoric acid of various concentrations. On the contrary, the conductivity of polypyrrole was reduced as the concentration of phosphoric acid became higher. The type of protonation is discussed with the help of FTIR spectra by analyzing the ammonium salts obtained after deprotonation. Sulfate or hydrogen sulfate anions produced from peroxydisulfate always constitute a part of the counter-ions.     

Selective determination of penicillamine by on-line vapor-phase generation combined with Fourier transform infrared spectrometry

In this work, an on-line system with vapor-phase generation (VPG) and Fourier transform infrared (FTIR) spectrometric detection has been developed as a direct and highly selective analytical technique for the assay of penicillamine (PA). Potassium iodate solution was injected into a reactor, heated at 75 °C, containing PA. The CO generated under these conditions was transported by means of N₂ gas carrier stream to an infrared gas cell and corresponding FTIR spectra were acquired in a continuous mode. The maximum absorbance of CO band at 2170 cm⁻¹, corrected by a baseline established between 2240 and 2000 cm⁻¹ at a nominal resolution of 2 cm⁻¹, was selected as a measurement criterion. Initially, the effect of different chemical, physical and spectroscopic parameters, such as concentration and volume of oxidant, pH, equilibrium time, reactor temperature, reactor volume, N₂ carrier flow rate and number of scans on the analytical signals were evaluated by using a short path length (10 cm) IR gas cell. At optimum experimental conditions, the method provided a relatively broad linear dynamic range of 4-380 mg L⁻¹, a limit of detection of 0.5 mg L⁻¹, a sampling frequency of 15 h⁻¹ and a relative standard deviation (R.S.D.) of 1.6%. Further, the method was successfully applied to the determination of PA in pharmaceutical formulations and results compared well with those obtained by a reference colorimetric method.