A sensitive spectrophotometric method for determination of carbon tetrachloride with the aid of ultrasonic decolorization of methyl orange

A sensitive method for carbon tetrachloride (CCl₄) determination has been developed with the aid of ultrasonic oxidation decolorization of methyl orange (MO). It is found that the ultrasonic oxidation decolorization rate of MO can be significantly promoted by adding a little amount of CCl₄. The increased ultrasonic decolorization rate of MO is strongly dependent on the concentration of CCl₄ added, and a linear correlation is observed between the amount of CCl₄ and the decolorization rate of MO in the ultrasonic oxidation process. Thus, the CCl₄ determination is transformed to a simple and direct determination of the decoloration extent of MO solution at a given concentration. As an indirect spectrophotometric determination of CCl₄, the new method is sensitive and easy of operation with a maximum wavelength of 508 nm, molar absorptivity of 3.83 × 10⁴ L mol⁻¹ cm⁻¹, and a Sandell sensitivity of 7.96 × 10⁻³ μg cm⁻². Under optimized conditions, Beer's law is obeyed in the range of 0.4-20 mg L⁻¹ of CCl₄ (DL = 0.19 mg L⁻¹, r = 0.9996). The concentrations of CCl₄ in several practical samples have been determined satisfactorily by using this method.     

New tridentate cyclometalated platinum(II) and palladium(II) complexes of N,2-diphenyl-8-quinolinamine: syntheses, crystal structures, and photophysical properties

A new tridentate cyclometalated platinum(II) complex derived from N,2-diphenyl-8-quinolinamine, which consists of two crystallographic independent molecules with two intermolecular N-H-Cl-Pt hydrogen bonds forming a dimer, exhibited a low-energy luminescence at ca. 740 nm in a 1 × 10⁻³ M dichloromethane solution and a strong emission centered at 670 nm in a solid state, but the analogous palladium(II) complex was nonemissive at room temperature.     

Experimental and quantum chemical study of pyrrole self-association through N-H?π hydrogen bonding

An FT-IR study of pyrrole self-association in CCl₄ solutions was carried out. According to the IR measurements, pyrrole forms self-associated dimeric species via N-H?π hydrogen bonding. This was also confirmed by quantum chemical calculations for pyrrole monomer and dimer at B3LYP/6-31++G(d,p) level of theory. A T-shaped minimum was located on B3LYP/6-31++G(d,p) PES of pyrrole dimer characterized with a hydrogen bond of an N-H?π type, with centers-of-mass separation of monomeric units of 4.520 Å, H?π distance of 2.475 Å, the interplanar angle between the two monomeric units being 72.9°. The anharmonic vibrational frequency shift upon dimer formation calculated on the basis of 1D DFT vibrational potentials is in excellent agreement with the experimental data (84 vs. 87 cm⁻¹). Harmonic vibrational analysis predicts somewhat smaller shift (68 cm⁻¹). On the basis of NIR spectroscopic data, anharmonicity constants for the 2ν(N-H) and 2ν(N-H?π) vibrational transitions were calculated. The orientational dynamics of monomeric and self-associated pyrrole species was studied within the framework of the transition dipole moment time correlation function formalism. The period of essentially free rotation in the condensed phase reduces from 0.05 ps for the monomeric pyrrole to 0.02 ps for the proton-donor molecule within the dimer.     

Spectrophotometric determination of carbon tetrachloride via ultrasonic oxidation of iodide accelerated by dissolved carbon tetrachloride

Ultrasonic oxidation of iodide was investigated in the presence of carbon tetrachloride (CCl₄). The ultrasonic oxidation of potassium iodide led to formation of iodine and then I₃⁻ in the presence of excess iodide, and the generated I₃⁻ shows strong UV absorption with a molar absorptivity of 2.31 × 10⁴ L mol⁻¹ cm⁻¹ at the maximum absorption wavelength of 351 nm. The ultrasonic oxidation of iodide was found to be significantly promoted by a small addition of CCl₄, and it was further found that the generation rate was increased with the amount of CCl₄ added. This can be used to analyze the level of CCl₄ dissolved in aqueous solutions. Under optimum conditions, the concentration of generated iodine (or its absorption at 351 nm) was found to correlated linearly with the concentration of CCl₄ in the range of 0.2-50 mg L⁻¹ (detection limit = 0.09 mg L⁻¹, R² = 0.999). As an alternative indirect spectrophotometric method of CCl₄ determination, the proposed method was successfully applied to determine the concentrations of CCl₄ in several practical samples, showing merits of being sensitive and simple of operation.     

Resonance Raman spectroscopy and DFT calculations of the protonation of 4-(2-pyridylazo)-N,N-dimethylaniline in solution and adsorbed on oxide surfaces

The protonation of 4-(2-pyridylazo)-N,N-dimethylaniline (PYAD) in aqueous solution and its adsorption on oxide surfaces has been studied by resonance Raman (RR) spectroscopy. The gas phase structures of neutral, protonated and diprotonated forms of PYAD were modelled by SCF-DFT calculations at the B3-LYP/DZ level, enabling determination of the simulated vibrational spectra of these species, together with vibrational assignments, and providing confirmation that protonation occurs initially at the pyridyl nitrogen atom. Electronic absorption spectra were interpreted using time-dependent DFT calculations. Adsorption of PYAD on SiO₂ or Al₂O₃ surfaces is mainly via the neutral species, hydrogen bonded to surface OH groups, although a small proportion of adsorbed molecules are protonated. By contrast, adsorption on SiO₂–Al₂O₃ results in complete protonation, indicating the presence of Brønsted acidic sites with pK_a values ? 4.5, whereas adsorption on H-mordenite results in diprotonation, indicating the presence of Brønsted acidic sites with pK_a values ? 2.     

Overcoming interference from the alumina matrix on the determination of arsenic at 189 nanometers using electrothermal atomic absorption spectrometry

A method is described enabling to eliminate the spectral interference from alumina matrix onto As determination at the wavelength 189 nm by electrothermal atomic absorption spectrometry with deuterium background correction. Matrix modification was performed by the addition of ammonium fluoride to protect the formation of aluminium oxide implicated in causing spectral interference and to increase volatility of alumina matrix via the formation of AlF₃. Pre-treating of the pyrolytic graphite platform with a solution of rhodium and citric acid has enabled to stabilize the analyte up to temperature of 1300 °C at which most of AlF₃ could be removed from the graphite furnace. The application of 2 μg of Rh + 20 μg of citric acid + 200 μg of NH₄F has enabled an accurate and interference-free determination of As up to 40 μg of Al in the form of AlCl₃ as verified by analytical recoveries study and resulted in characteristic mass and LOD value in the original sample 15 pg and 50 ng g⁻¹, respectively (10-μL aliquots of sample).     

Structural information from OH stretching frequencies—conformations of cyclohexanol and cyclohexandiols

Infrared spectra of cyclohexanol and the trans and cis forms of cyclohexandiols with 1,4-, 1,3- and 1,2-OH groups in solution in CCl₄, CDCl₃ and in low temperature matrices in argon are reported for the OH stretching region. Band splittings are observed in the matrix state and the components are assigned to equatorial and axial OH groups. These are not split in spectra of solutions because of the greater band width in this state. Bands from hydrogen bonded forms are observed for favourable spatial arrangements.     

Supramolecular interaction of ethylenediamine linked beta-cyclodextrin dimer and berberine hydrochloride by spectrofluorimetry and its analytical application

The supramolecular interaction of β-cyclodextrin dimer with berberine hydrochloride was studied in aqueous KH₂PO₄-H₃PO₄ buffer solution of pH 2.00 at room temperature by spectrofluorimetry. The apparent association constant of the complex was 1.53 × 10⁴ L mol⁻¹. Based on the significant enhancement of fluorescence intensity of supramolecular sandwich complexes, a spectrofluorimetric method with high sensitivity and selectivity was developed for the determination of berberine hydrochloride in aqueous solution in presence of ethylenediamine linked β-CD dimer. The linear range of the method was 12.8-1.00 × 10⁴ ng mL⁻¹ with the detection limit 3.6 ng mL⁻¹. There was no interference from the normally used in tablets and serum constituents. The proposed method was successfully applied to the determination of berberine hydrochloride in tablets and serum. And then it has a promising potential in therapeutic drug monitoring, pharmokinetis and clinical application.     

Aqua cadmium cyanide coordination polymer with nitronyl nitroxide radical

A new three-dimensional diamagnetic metal nitronyl nitroxide radical coordination polymer with an aqua cadmium cyanide framework Cd(NIT4py)(H₂O)Cd(CN)₄·H₂O 1, was synthesized. X-ray crystallography reveals that the structure consists of 3D aqua cadmium cyanide built up by octahedral Cd^II coordinating to NIT4py and tetrahedral Cd^II (CN)₄ units. Magnetic measurements show that the χ_mT values are nearly constant at higher temperature. The lower χ_mT values at lower temperature are related to intermolecular antiferromagnetic interactions of the radicals, which arise due to the hydrogen bonded network (T_N = 21 K).     

Synthesis and decarboxylation of N-acyl-α-triphenylphosphonio-α-amino acids: a new synthesis of α-(N-acylamino)alkyltriphenylphosphonium salts

4-Phosphoranylidene-5(4H)-oxazolones 1 undergo hydrolysis in THF in the presence of HBF₄ at room temperature to give N-acyl-α-triphenylphosphonioglycines 3 (R² = H) in very good yields. 4-Alkyl-4-triphenylphosphonio-5(4H)-oxazolones 2 react with water in CH₂Cl₂/THF solution without any acidic catalyst at 0-5 °C in a few days yielding N-acyl-α-triphenylphosphonio-α-amino acids 3 (R² = Me) or α-(N-acylamino)alkyltriphenylphosphonium salt 4 (R² = CH₂OMe). α-Triphenylphosphonio-α-amino acids 3, on heating up to 105-115 °C under reduced pressure (5 mmHg) or on treatment with diisopropylethylamine in CH₂Cl₂ at 20 °C undergo decarboxylation to give the corresponding α-(N-acylamino)alkyltriphenylphosphonium salts 4, usually in very good yields.     

Cobalt-doped silica membranes for gas separation

Cobalt-doped silica membranes were synthesized using tetraethyl orthosilicate-derived sol mixed with cobalt nitrate hexahydrate. The cobalt-doped silica structural characterization showed the formation of crystalline Co₃O₄ and silanol groups upon calcination. The metal oxide phase was sequentially reduced at high temperature in rich hydrogen atmosphere resulting in the production of high quality membranes. The cobalt concentration was almost constant throughout the film depth, though the silica to cobalt ratio changed from 33:1 at the surface to 7:1 at the interface with the alumina layer. It is possible that cobalt has more affinity to alumina, thus forming CoOAl₂O₃. The He/N₂ selectivities reached 350 and 570 at 160 °C for dry and 100 °C wet gas testing, respectively. Subsequent exposure to water vapour, the membranes was regenerated under dry gas condition and He/N₂ selectivities significantly improved to 1100. The permeation of gases generally followed a temperature dependency flux or activated transport, with best helium permeation and activation energy results of 9.5 × 10⁻⁸ mol m⁻² s⁻¹ Pa⁻¹ and 15 kJ mol⁻¹. Exposure of the membranes to water vapour led to a reduction in the permeation of nitrogen, attributed to water adsorption and structural changes of the silica matrix. However, the overall integrity of the cobalt-doped silica membrane was retained, given an indication that cobalt was able to counteract to some extent the effect of water on the silica matrix. These results show the potential for metal doping to create membranes suited for industrial gas separation.     

Gas-phase electron diffraction study of cyclic dimer of dimethylphosphinic acid (Me2P(O)OH)2 using quantum chemical data and a priori force field

The molecular structure of the hydrogen bonded cyclic dimer of dimethylphosphinic acid (Me₂P(O)OH)₂ was determined by gas-phase electron diffraction (GED) at 433 K. The presence of monomer cannot be determined at this temperature within the error limits for the GED method. Structural analysis was performed with consideration of non-linear kinematic effects at the first-order level of perturbation theory (h1). The vibrational characteristics of internuclear distances were calculated from a priori scaled quantum chemical (RHF/6-311G**) force field. The analysis aided by a constraint based on the RHF/6-311G** calculations yielded the following r_h1-parameters of the C₂-symmetry dimer configuration: PO 1.497(3); P-O 1.573(4); P-C 1.806(1) and 1.811(1) Å; (C-H)_av. 1.109(3) Å; ∠O-PO 120(1)°. Unlike PO and P-O bonds, whose lengths in the gas phase and in the solid state differ insignificantly, the -O?O distance in the gas phase (r_h1 2.81(4) Å) is considerably longer than in the solid state (r_α 2.48(2) Å). The latter is in accordance with the conclusion based on the IR spectra that transition from gas to a solid sample leads to strengthening of the H-bonds. Due to its small contribution to the diffraction pattern, the donor O-H bond length (r_h1 0.99(1) Å) was forcedly bound up with the parameters of C-H bonds. With this assumption, the other geometrical parameters characterizing the H-bond fragment have the following r_h1 values: O?H 1.84(4) Å, ∠-OHO164(6)°, and ∠P-O-H 117(4)°. Conformational flexibility of the non-planar eight-atom ring of the dimer is experimentally verified by absence of any apparent peaks of the f(r) curve at the r-region of more than 4.2 Å.     

The phonon-assisted proton transfer between hydrazinium cations in (N2H5)2HMF6·2H2O (M∈{Ga, Al, Fe}) type compounds. FT IR and quantum theoretical study

FT IR spectra of a series of compounds with a general formula (N₂H₅)₂HMF₆·2H₂O (where M∈{Ga, Al, Fe}) were recorded at variable temperatures (from ∼100 to 300 K, at 10 K intervals). The appearance of the spectral region of ν(N-N) modes due to hydrazinium cations further supports the conclusions regarding the N₂H₅⁺?H⁺?N₂H₅⁺ hydrogen bond potential well based on Raman spectroscopic data [J. Raman Spectrosc. 28 (1997) 315]. The appearance of two bands corresponding to the ν(N-N) modes in the low temperature FT IR spectra that merge into one upon heating is a clear evidence of a symmetric potential well through which a phonon-assisted proton transfer (PAPT) occurs at higher temperatures. Ab initio MP2/6-311++G(2d,p) quantum chemical study of the proton transfer potential within the N₂H₅⁺?H⁺?N₂H₅⁺ cluster confirmed its double-minimum character. The first-order saddle point found on the MP2/6-311++G(2d,p) potential energy hypersurface corresponds to a centrosymmetric structure (C_2h symmetry), with the proton placed at the inversion center. The potential energy curve along the tunnelling coordinate was calculated by the intrinsic reaction coordinate (IRC) methodology, leading to an adiabatic PT barrier height of 3.94 kcal mol⁻¹ and a tunneling rate of 1.98 s⁻¹. The corresponding MP4(SDTQ)/6-311++G(2d,p)//MP2/6-311++G(2d,p) value of the adiabatic PT barrier height is 4.26 kcal mol⁻¹.     

Kinetics of tetrachloromethane fluorination by hydrogen fluoride in the presence of antimony pentachloride

Contradictory information concerning the kinetics of tetrachloromethane fluorination by anhydrous hydrogen fluoride in the presence of antimony pentachloride has been explained. The present studies were performed using a stainless steel autoclave. The exchange of the first chlorine atom was carried out in the temperature range of 35-95 °C, with the molar ratio of HF/CCl₄ varied within the range of 1.2-1.7 and at a constant molar ratio of SbCl₅/Cl₂ equal to 1.9. The degree of conversion of CCl₄ to CCl₃F and the reaction rate constant as a function of temperature fit to an Arrhenius straight line. The Arrhenius constants (pre-exponential factor) and the activation energy were determined. Studies concerning the exchange of the second chlorine atom, i.e. the conversion of CCl₃F to CCl₂F₂ have been performed. The results of kinetic investigations were created in the same way. Based on these results it was found that the Arrhenius equation is fulfilled also in the second stage of the fluorination. The same slope of the straight lines confirms that the fluorination stages proceed according to the same mechanism with the same activation energy but with different pre-exponential factors.Several kinetic problems associated with the performance of the reactor can be solved on the basis of the equations derived. However, knowledge of CCl₄ conversion as a function of time, temperature, catalyst concentration and the type of the reaction is required for this purpose. Such calculations enable the selection of the optimal process parameters.     

Synthesis and characterization of polyamides containing pendant pentadecyl chains

A new aromatic diacid monomer viz., 4-(4′-carboxyphenoxy)-2-pentadecylbenzoic acid was synthesized starting from cardanol and was characterized by FTIR, ¹H- and ¹³C NMR spectroscopy. A series of new aromatic polyamides containing ether linkages and pendant pentadecyl chains was prepared by phosphorylation polycondensation of 4-(4′-carboxyphenoxy)-2-pentadecylbenzoic acid with five commercially available aromatic diamines viz., 1,4-phenylenediamine, 4,4′-oxydianiline, 4,4′-methylenedianiline, 1,3-phenylenediamine, and 4,4′-(hexafluoroisopropylidene)dianiline. Inherent viscosities of the polyamides were in the range 0.45-0.66 dL/g in N,N-dimethylacetamide at 30 ± 0.1 °C. The introduction of ether linkages and pendant pentadecyl chains into polyamides led to an enhanced solubility in N,N-dimethylacetamide and 1-methyl-2-pyrrolidinone at room temperature or upon heating. The polyamides could be solution-cast into tough, flexible and transparent films from their N,N-dimethylacetamide solution. Wide angle X-ray diffraction patterns exhibited broad halo indicating that the polymers were essentially amorphous in nature. X-Ray diffractograms also displayed a diffuse to sharp reflection in the small-angle region (2θ = ∼2-5°) for the polyamides characteristics of formation of loosely to well-developed layered structure arising from packing of flexible pentadecyl chains. The glass transition temperature observed for the polyamides was in range 139-189 °C. The temperature at 10% weight loss (T₁₀), determined by TGA in nitrogen atmosphere, of the polyamides was in the range 425-453 °C indicating their good thermal stability.     

Advantages and effects of nitrogen doping into the central channel of plasma in axially viewed-inductively coupled plasma optical emission spectrometry

The effects and benefits of N₂ addition to the central channel of the ICP through the nebulizer gas used in ICP OES with axial view configuration were investigated in the present study. The N₂ flow rate, nebulizer gas flow rate, RF power and sample uptake rate were evaluated and compared for two sample introduction systems (pneumatic nebulization/aerosol desolvation and conventional pneumatic nebulization). It was observed that N₂ did not affect solution nebulization and aerosol transport but affects the ICP characteristics. The higher thermal conductivity of N₂ (in comparison with Ar) changes energy distribution in the ICP, observed by monitoring the signals of Ar emission lines and sodium emission. The ratio Mg(II)-280.270 nm/Mg(I)-285.213 nm was utilized as a diagnostic tool for plasma robustness. The addition of N₂ (20 mL min⁻¹) increased plasma robustness significantly and mitigated effects caused by Na, K and Ca. For 40 spectral lines evaluated, it was observed that the emission signals of ionic spectral lines were in general more affected by N₂ than those of atomic spectral lines. Detection limits, precision, sensitivity and linearity of calibration curves obtained using N₂-Ar-ICP were almost similar to those obtained using Ar-ICP. The analysis of 5 different reference materials revealed that accuracy was not degraded by adding N₂ to the Ar-ICP.     

Selective syntheses of benzoxazoles and N-(2-hydroxyaryl)pyrrolidin-2-ones from the corresponding cyclopropyl amides with PPh3/CX4

Benzoxazoles 2 can be smoothly synthesized by treatment of starting materials of N-(2-hydroxyaryl) cyclopropyl amides 1 with PPh₃/CCl₄ in acetonitrile in good yields. When PPh₃/CBr₄/MS 4 Å was used in the reaction system, the corresponding ring-expanding products 3 were obtained in moderate to good yields in acetonitrile at 80 °C. Using DCE as a solvent in this reaction, the corresponding 2-(3-chloropropyl)benzoxazoles 5 were obtained as major products.     

Preparation, structure and photoluminescence properties of Eu and Ce-doped SrYSi4N7

Undoped and Eu²⁺ or Ce³⁺-doped SrYSi₄N₇ were synthesized by solid-state reaction method at 1400-1660 °C under nitrogen/hydrogen atmosphere. The crystal structure was refined from the X-ray powder diffraction data by the Rietveld method. SrYSi₄N₇ and EuYSi₄N₇, being isotypic with the family of compounds MYbSi₄N₇ (M=Sr, Eu, Ba) and BaYSi₄N_7, crystallize with the hexagonal symmetry: space group P6₃mc (No. 186), Z=2, a=6.0160 (1) Å, c=9.7894 (1) Å, V=306.83(3) Å³; and a=6.0123 (1) Å, c=9.7869 (1) Å, V=306.37(1) Å³, respectively. Photoluminescence properties have been studied for Sr_1−xEu_xYSi₄N₇ (x=0-1) and SrY_1−xCe_xSi₄N₇ (x=0-0.03) at room temperature. Eu²⁺-doped SrYSi₄N₇ shows a broad yellow emission band peaking around 548-570 nm, while Ce³⁺-doped SrYSi₄N₇ exhibits a blue emission band with a maximum at about 450 nm. SrYSi₄N₇:Eu²⁺ can be very well excited by 390 nm radiation, which makes this material attractive as conversion phosphor for LED lighting applications.     

Application of copper sulfate pentahydrate as an ammonia removal reagent for the determination of trace impurities in ammonia by gas chromatography

Rapid analysis of trace permanent gas impurities in high purity ammonia gas for the microelectronics industry is described, using a gas chromatograph equipped with a phtoionization detector. Our system incorporates a reactive precolumn in combination with the analytical column to remove the ammonia matrix peak that otherwise would complicate the measurements due to baseline fluctuations and loss of analytes. The performance of 21 precolumn candidate materials was evaluated. Copper sulfate pentahydrate (CuSO₄·5H₂O) was shown to selectively react with ammonia at room temperature and atmospheric column pressures, without affecting the hydrogen, oxygen, nitrogen, methane or carbon monoxide peak areas. To prevent loss of trace carbon dioxide, an additional boron trioxide reactant layer was inserted above the copper sulfate pentahydrate bed in the reactive precolumn. Using the combined materials, calibration curves for carbon dioxide proved to be equivalent in both ammonia and helium matrix gases. These curves were equivalent in both matrix gases. The quantitative performance of the system was also evaluated. Peak repeatabilities, based on eight injections, were in the range of 4.1–8.2% relative standard deviation; and detection limits were 6.9 ppb for H₂, 1.8 ppb for O₂, 1.6 ppb for N₂, 6.4 ppb for CH₄, 13 ppb for CO, and 5.4 ppb for CO₂.     

Improved and facile addition reactions of pentafluorosulfanyl bromide

A solution of SF₅Br in CCl₃F (0.5-1 M) was utilized to effect the addition of pentafluorosulfanyl bromide (SF₅Br) to olefins. The reaction of the SF₅Br solution in the presence of triethylborane (0.1 equiv) with an olefin over 20 min at 0 °C gave pentafluorosulfanylated compound 2(a-f) in high yield (Table 2). An efficient route for the preparation of synthetically useful SF5-containing esters is also described.