Analysis of non-symmetrical flapping airfoils

Simulations have been done to assess the lift, thrust and propulsive efficiency of different types of non-symmetrical airfoils under different flapping configurations. The variables involved are reduced frequency, Strouhal number, pitch amplitude and phase angle. In order to analyze the variables more efficiently, the design of experiments using the response surface methodology is applied. Results show that both the variables and shape of the airfoil have a profound effect on the lift, thrust, and efficiency. By using non- symmetrical airfoils, average lift coefficient as high as 2.23 can be obtained. The average thrust coefficient and efficiency also reach high values of 2.53 and 0.61, respectively. The lift production is highly dependent on the airfoil＇s shape while thrust production is influenced more heavily by the variables. Efficiency falls somewhere in between. Two-factor interac- tions are found to exist among the variables. This shows that it is not sufficient to analyze each variable individually. Vorticity diagrams are analyzed to explain the results obtained. Overall, the S1020 airfoil is able to provide relatively good efficiency and at the same time generate high thrust and lift force. These results aid in the design of a better ornithopter＇s wing.     

Effects of mass and chordwise flexibility on 2D self-propelled flapping wings

A self-propelled flexible flapping wing 2D numerical model undergoing a combined pitching and heaving motion is presented. Since such freely moving foil experiences zero net thrust, a definition of efficiency for this kind of problem is proposed and discussed against other formulations found in the literature. It is also shown that the deviation motion of wings such as that found in natural flyers is likely a consequence of the fluid–structure dynamics of the wings. The passive deviation motion observed in numerical simulations is either a consequence of a feathering mechanism referred to as rigid feathering or of the inertial displacement caused by the wing deformation. The effects of flexibility on the performance of the wing are also presented. It is found that flexibility may significantly enhance the efficiency in pressure-driven deformation cases. The rigid feathering mechanism is found to have an effect similar to that of the feathering caused by wing flexibility on the performances of pressure-driven deformation cases.     

Numerical analysis of the s1020 airfoils in tandem under different flapping configurations

The objective of this project is to improve the performance of the efficiency, thrust and lift of flapping wings in tandem arrangement. This research investigates the effect of the arrangement of the airfoils in tandem on the performance of the airfoils by varying the phase difference and distance between the airfoils. Three flapping configurations from an earlier phase of a research which gives high efficiency, thrust and lift are used in the tandem simulation. It is found all the different flapping configurations show improvement in the efficiency, thrust or lift when the distance between the two airfoils and the phase angle between the heaving positions of the two airfoils are optimal. The average thrust coefficient of the tandem arrangement managed to attain more than twice that of the single one （4.84 vs. 2.05）. On the other hand, the average lift coefficient of the tandem arrangement also increased to 4.59, as compared to the original single airfoil value of 3.04. All these results obtained will aid in the design of a better ornithopter with tandem wing arrangement.     

Experimental investigation of the effect of chordwise flexibility on the aerodynamics of flapping wings in hovering flight

Ornithopters or mechanical birds produce aerodynamic lift and thrust through the flapping motion of their wings. Here, we use an experimental apparatus to investigate the effects of a wing's twisting stiffness on the generated thrust force and the power required at different flapping frequencies. A flapping wing system and an experimental set-up were designed to measure the unsteady aerodynamic and inertial forces, power usage and angular speed of the flapping wing motion. A data acquisition system was set-up to record important data with the appropriate sampling frequency. The aerodynamic performance of the vehicle under hovering (i.e., no wind) conditions was investigated. The lift and thrust that were produced were measured for different flapping frequencies and for various wings with different chordwise flexibilities. The results show the manner in which the elastic deformation and inertial flapping forces affect the dynamical behavior of the wing. It is shown that the generalization of the actuator disk theory is, at most, only valid for rigid wings, and for flexible wings, the power P varies by a power of about 1.0  of the thrust T. This aerodynamic information can also be used as benchmark data for unsteady flow solvers.     

Influence of wing flexibility on the aerodynamic performance of a tethered flapping bumblebee

The sophisticated structures of flapping insect wings make it challenging to study the role of wing flexibility in insect flight. In this study, a mass-spring system is used to model wing structural dynamics as a thin, flexible membrane supported by a network of veins. The vein mechanical properties can be estimated based on their diameters and the Young's modulus of cuticle. In order to analyze the effect of wing flexibility, the Young's modulus is varied to make a comparison between two different wing models that we refer to as flexible and highly flexible. The wing models are coupled with a pseudo-spectral code solving the incompressible Navier–Stokes equations, allowing us to investigate the influence of wing deformation on the aerodynamic efficiency of a tethered flapping bumblebee. Compared to the bumblebee model with rigid wings, the one with flexible wings flies more efficiently, characterized by a larger lift-to-power ratio.     

Numerical investigation on aerodynamic performance of a bionic flapping wing

This paper numerically studies the aerodynamic performance of a bird-like bionic flapping wing. The geometry and kinematics are designed based on a seagull wing,in which flapping, folding, swaying, and twisting are considered. An in-house unsteady flow solver based on hybrid moving grids is adopted for unsteady flow simulations. We focus on two main issues in this study, i.e., the influence of the proportion of down-stroke and the effect of span-wise twisting. Numerical results show that the proportion of downstroke is closely related to the efficiency of the flapping process. The preferable proportion is about 0.7 by using the present geometry and kinematic model, which is very close to the observed data. Another finding is that the drag and the power consumption can be greatly reduced by the proper span-wise twisting. Two cases with different reduced frequencies are simulated and compared with each other. The numerical results show that the power consumption reduces by more than 20%, and the drag coefficient reduces by more than 60% through a proper twisting motion for both cases. The flow mechanism is mainly due to controlling of unsteady flow separation by adjusting the local effective angle of attack. These conclusions will be helpful for the high-performance micro air vehicle(MAV) design.     

Effect of spanwise flexibility on flapping wing propulsion

A water tunnel study of the effect of spanwise flexibility on the thrust, lift and propulsive efficiency of a rectangular wing oscillating in pure heave has been performed. The thrust and lift forces were measured with a force balance, and the flow field was measured with a Particle Image Velocimetry system. Introducing a degree of spanwise flexibility was found to be beneficial. For Strouhal numbers greater than 0.2, a degree of spanwise flexibility was found to yield a small increase in thrust coefficient, and a small decrease in power-input requirement, resulting in higher efficiency. In this case, a moderately stronger trailing-edge vortex system was observed. Introducing a far greater degree of spanwise flexibility, however, was found to be detrimental. A large phase delay of the wing tip displacement was observed, leading to the root and tip moving in opposite directions for a significant portion of the flapping stroke. Vorticity of opposing sign was observed to be shed from the root and tip, resulting in a weak and fragmented vorticity pattern. The thrust coefficient was observed to be significantly reduced, and the efficiency diminished. It is noted that the range of Strouhal numbers for which spanwise flexibility was found to offer benefits overlaps the range found in nature, of 0.2<Sr<0.4. From a design aspect, flexibility may benefit flapping-wing Micro Air Vehicles both aerodynamically and in the inherent lightness of flexible structures.     

Effect of skin flexibility on aerodynamic performance of flexible skin flapping wings for micro air vehicles

Experimental Techniques - As part of the ongoing research on micro air vehicles, the present work focuses on the effect of membrane flexibility on the aerodynamic performance of flexible latex...     

Aerodynamic force and flow structures of two airfoils in flapping motions

Aerodynamic force and flow structures of two airfoils in a tandem configuration in flapping motions are studied, by solving the Navier-Stokes equations in moving overset grids. Three typical phase differences between the fore- and aftairfoil flapping cycles are considered. It is shown that: (1) in the case of no interaction (single airfoil), the time average of the vertical force coefficient over the downstroke is 2.74, which is about 3 times as large as the maximum steady-state lift coefficient of a dragonfly wing; the time average of the horizontal force coefficient is 1.97, which is also large. The reasons for the large force coefficients are the acceleration at the beginning of a stroke, the delayed stall and the “pitching-up” motion near the end of the stroke. (2) In the cases of two-airfoils, the time-variations of the force and moment coefficients on each airfoil are broadly similar to that of the single airfoil in that the vertical force is mainly produced in downstroke and the horizontal force in upstroke, but very large differences exist due to the interaction. (3) For in-phase stroking, the major differences caused by the interaction are that the vertical force on FA in downstroke is increased and the horizontal force on FA in upstroke decreased. As a result, the magnitude of the resultant force is almost unchanged but it inclines less forward. (4) For counter stroking, the major differences are that the vertical force on AA in downstroke and the horizontal force on FA in upstroke are decreased. As a result, the magnitude of the resultant force is decreased by about 20 percent but its direction is almost unchanged. (5) For 90°-phase-difference stroking, the major differences are that the vertical force on AA in downstroke and the horizontal force on FA in upstroke are decreased greatly and the horizontal force on AA in upstroke increased. As a result, the magnitude of the resultant force is decreased by about 28% and it inclines more forward. (6) Among the three cases of phase angles, inphase flapping produces the largest vertical force (also the largest resultant force); the 90°-phase-difference flapping results in the largest horizontal force, but the smallest resultant force.     

Numerical analysis on transitions and symmetry-breaking in the wake of a flapping foil

Flying and marine animals often use flapping wings or tails to generate thrust. In this paper, we will use the simplest flapping model with a sinusoidal pitching motion over a range of frequency and amplitude to investigate the mechanism of thrust generation. Previous work focuses on the Karman vortex street and the reversed Karman vortex street but the transition between two states remains unknown. The present numerical simulation provides a complete scenario of flow patterns from the Karman vortex street to reversed Karman vortex street via aligned vortices and the ultimate state is the deflected Karman vortex street, as the parameters of flapping motions change. The results are in agreement with the previous experiment. We make further discussion on the relationship of the observed states with drag and thrust coefficients and explore the mechanism of enhanced thrust generation using flapping motions.     

前后双扑翼水平距离及相位差对其气动性能的影响

通过在动态网格上求解Navier-Stokes方程,对前后双扑翼的非定常粘性流场进行了数值模拟和气动干扰分析,考察了前后翼不同水平距离和不同相位差对其气动力和气动效率的影响。结果表明,扑动前翼和静止后翼间的气动干扰在各种不同水平距离下都有利于气动特性的改善,但气动干扰的作用随着前后翼水平距离的增大而减弱;前后双翼扑动的相位差是影响气动性能的重要参数,两翼间的气动干扰是否有利则与相位差和水平距离有直接联系。     

Thrust augmentation of flapping airfoils in low Reynolds number flow using a flexible membrane

The unsteady aerodynamic thrust and aeroelastic response of a two-dimensional membrane airfoil under prescribed harmonic motion are investigated computationally with a high-order Navier–Stokes solver coupled to a nonlinear membrane structural model. The effects of membrane prestress and elasticity are examined parametrically for selected plunge and pitch–plunge motions at a chord-based Reynolds number of 2500. The importance of inertial membrane loads resulting from the prescribed flapping is also assessed for pure plunging motions. This study compares the period-averaged aerodynamic loads of flexible versus rigid membrane airfoils and highlights the vortex structures and salient fluid–membrane interactions that enable more efficient flapping thrust production in low Reynolds number flows.     

Numerical experiments on the transient motions of a flapping foil

The flow field generated by a foil during transient motions is investigated by means of numerical experiments. The numerical simulations have some advantages with respect to laboratory experiments. Indeed, having access to the velocity and pressure fields both in space and in time, it is possible to 'measure' quantities like vorticity, forces and torques which are quite difficult to obtain in laboratory. Moreover, data can be easily gained for different foil kinematics. The obtained results show that the time history of the propulsive force strongly depends on the details of the kinematics of the foil. Moreover, the numerical simulations have allowed to understand the main mechanisms employed by fish to propel themselves during fast starts and to identify the values of the parameters providing optimal propulsive performances.     

Numerical simulation of a flapping four-wing micro-aerial vehicle

A three-dimensional numerical simulation of a four-wing (two wings on each side, one on top of another) flapping micro-aerial vehicle (FMAV), known as the Delfly micro, is performed using an immersed boundary method Navier–Stokes finite volume solver at Reynolds numbers of 5500 (forward flight condition). The objective of the present investigation is to gain an insight to the aerodynamics of flapping wing biplane configuration, by making an analysis on a geometry that is simplified, yet captures the major aspects of the wing behavior. The fractional step method is used to solve the Navier–Stokes equations. Results show that in comparison to the Delfly II flapping kinematics (a similar FMAV configuration but smaller flapping stroke angles), the Delfly-Micro flapping kinematics provides more thrust while maintaining the same efficiency. The Delfly-Micro biplane configuration generates more lift than expected when the inclination angle increases, due to the formation of a uniform leading edge vortex. Estimates of the lift produced in the forward flight conditions confirm that in the current design, the MAV is able to sustain forward flight. The potential effect of wing flexibility on the aerodynamic performance in the biplane configuration context is investigated through prescribed flexibility in the simulations. Increasing the wing׳ spanwise flexibility increases thrust but increasing chordwise flexibility causes thrust to first increase and then decrease. Moreover, combining both spanwise and chordwise flexibility outperforms cases with only either spanwise or chordwise flexibility.     

Experimental study of wings undergoing active root flapping and pitching

This paper presents the results of experiments carried out on mechanical wings undergoing active root flapping and pitching in the wind tunnel. The objective of the work is to investigate the effect of the pitch angle oscillations and wing profile on the aerodynamic forces generated by the wings. The experiments were repeated for a different reduced frequency, airspeed, flapping and pitching kinematics, geometric angle of attack and wing sections (one symmetric and two cambered airfoils). A specially designed mechanical flapper was used, modelled on large migrating birds. It is shown that, under pitch leading conditions, good thrust generation can be obtained at a wide range of Strouhal numbers if the pitch angle oscillation is adjusted accordingly. Consequently, high thrust was measured at both the lowest and highest tested Strouhal numbers. Furthermore, the work demonstrates that the aerodynamic forces can be sensitive to the Reynolds number, depending on the camber of the wings. Under pitch lagging conditions, where the effective angle of attack amplitude is highest, the symmetric wing was affected by the Reynolds number, generating less thrust at the lowest tested Reynolds value. In contrast, under pure flapping conditions, where the effective angle of attack amplitude was lower but still significant, it was the cambered wings that demonstrated Reynolds sensitivity.     

翼型、机翼非定常运动模式下动态数值模拟

基于RANS方程,通过刚性动网格技术实现对翼型和机翼典型运动模式的描述,采用双时间推进方法和Roe空间离散格式对流场求解,构建了一个非定常气动计算平台;以NACA0012翼型为算倒进行了动态数值模拟可信度验证。数值模拟结果与试验数据吻合较好,升力和俯仰力矩的最大计算误差分别为3％和10％,表明了该平台的可靠性。另外,还数值模拟了M6机翼的动态非定常流场,并分析了两种湍流模型对非定常流场激波的捕捉能力。结果表明非定常流动中S-A湍流模型对激波的捕捉较B-L模型更敏感。文中开发的非定常计算平台对进一步解决三维复杂流场的流动问题有很高的工程应用价值。     

Numerical study of flapping filaments in a uniform fluid flow

The coupled dynamics of multiple flexible filaments (also called monodimensional flags) flapping in a uniform fluid flow is studied numerically for the cases of a side-by-side arrangement, and an in-line configuration. The modal behaviour and hydrodynamical properties of the sets of filaments are studied using a Lattice Boltzmann–Immersed Boundary method. The fluid momentum equations are solved on a Cartesian uniform lattice while the beating filaments are tracked through a series of markers, whose dynamics are functions of the forces exerted by the fluid, the filaments flexural rigidity and the tension. The instantaneous wall conditions on the filaments are imposed via a system of singular body forces, consistently discretised on the lattice of the Boltzmann equation. The results exhibit several flapping modes for two and three filaments placed side-by-side and are compared with experimental and theoretical studies. The hydrodynamical drafting, observed so far only experimentally on configurations of in-line flexible bodies, is also revisited numerically in this work, and the associated physical mechanism is identified. In certain geometrical and structural configuration, it is found that the upstream body experiences a reduced drag compared to the downstream body, which is the contrary of what is encountered on rigid bodies (cars, bicycles).     

冠脉支架纵向柔顺性数值模拟

柔顺性是冠脉支架重要的力学性能之一。本文针对一种具有非对称结构的冠脉支架,利用有限元方法深入研究与弯曲方向有关的支架柔顺性,在柔顺性数值模拟中使该支架获得较大的弯曲曲率并且考虑了接触因素。在一个周期结构内的多个弯曲方向上分别进行模拟,详细研究了支架抗弯刚度的各向异性。计算结果显示：在支架自接触现象发生前,支架的柔顺性表...