Numerical study of large amplitude,nonsinusoidal motion and camber effects on pitching airfoil propulsion

The effects of large amplitude and nonsinusoidal motion on pitching airfoil aerodynamics for thrust generation were numerically studied with a 2-D NACA0012 airfoil used, and various 2-D NACA asymmetric airfoils were applied for camber effect study. The large amplitude effect study has been undertaken over a wide range of reduced frequency k (from 6 to 18) and pitching amplitude θ (from 5° to 30°) at Re=1.35×10⁴ with sinusoidal pitching profile used. It is shown that the large pitching amplitude results in much more thrust generated than that at low pitching amplitude and the increase of thrust with amplitude becomes slow when the amplitude reaches some degree. However, the propulsive efficiency noticeably decreases with the increase of θ at a fixed k.An adjustable parameter K was employed to realize various nonsinusoidal motions and the effect of nonsinusoidal motion was investigated with various unsteady parameters (θ, k) applied. The results reveal that nonsinusoidal motion has a noticeable effect on the aerodynamic performance, as it affects the instantaneous force coefficients, maximum thrust coefficients and flow structures. An increase in K results in a better thrust generation performance at fixed θ and k, especially for K>0. It is also shown that the larger K noticeably influences the wake pattern and induces a stronger reverse von Karman vortex street in the wake, which in turn leads to the increased thrust. The camber study was performed on various 2-D NACA airfoils with different cambers and camber locations undergoing sinusoidal pitching motion at θ=5° and Re=1.35×10⁴. It is found that varying camber offers little improvement in thrust generation performance.     

Computational aeroelastic simulations of self-sustained pitch oscillations of a NACA0012 at transitional Reynolds numbers

The phenomenon of low amplitude self-sustained pitch oscillations in the transitional Reynolds number regime is studied numerically through unsteady, two-dimensional aeroelastic simulations. Based on the experimental data, simulations have been limited in the Reynolds number range 5.0×10⁴<Re_c<1.5×10⁵. Both laminar and URANS calculations (using the SST k–ω model with a low-Reynolds-number correction) have been performed and found to produce reasonably accurate limit cycle pitching oscillations (LCO). This investigation confirms that the laminar separation of the boundary layer near the trailing edge plays a critical role in initiating and sustaining the pitching oscillations. For this reason, the phenomenon is being labelled as laminar separation flutter. As a corollary, it is also shown that turbulence tends to inhibit their existence. Furthermore, two regimes of LCO are observed, one where the flow is laminar and separated without re-attachment, and the second for which transition has occurred followed by turbulent re-attachment. Finally, it is established that the high-frequency, shear instabilities present in the flow which lead to von Kármán vortex shedding are not crucial, nor necessary, to the maintaining mechanism of the self-sustained oscillations.     

Self-sustained aeroelastic oscillations of a NACA0012 airfoil at low-to-moderate Reynolds numbers

A wind tunnel experimental investigation of self-sustained oscillations of an aeroelastic NACA0012 airfoil occurring in the transitional Re regime is presented. To the authors’ knowledge this is the first time that aeroelastic limit cycle oscillations (LCOs) associated with low Re effects have been systematically studied and reported in the public literature. While the aeroelastic apparatus is capable of two-degree-of-freedom pitch-plunge motion, the present work concerns only the motion of the airfoil when it is constrained to rotate in pure pitch. The structural stiffness is varied as well as the position of the elastic axis; other parameters such as surface roughness, turbulence intensity and initial conditions are also briefly discussed. In conjunction with the pitch measurements, the flow is also recorded using hot-wire anemometry located in the wake at a distance of one chord aft of the trailing edge. It is observed that for a limited range of chord-based Reynolds numbers, 4.5×10⁴Re_c1.3×10⁵, steady state self-sustained oscillations are observed. Below and above that range, these oscillations do not appear. They are characterized by a well-behaved harmonic motion, whose frequency can be related to the aeroelastic natural frequency, low amplitude (θ_max<5.5°) and some sensitivity to flow perturbations and initial conditions. Furthermore, hot-wire measurements for the wing held fixed show that no periodicity in the undisturbed free-stream nor in the wake account for the oscillations. Overall, these observations suggest that laminar separation plays a role in the oscillations, either in the form of trailing edge separation or due to the presence of a laminar separation bubble.     

High-fidelity simulations of moving and flexible airfoils at low Reynolds numbers

The present paper highlights results derived from the application of a high-fidelity simulation technique to the analysis of low-Reynolds-number transitional flows over moving and flexible canonical configurations motivated by small natural and man-made flyers. This effort addresses three separate fluid dynamic phenomena relevant to small fliers, including: laminar separation and transition over a stationary airfoil, transition effects on the dynamic stall vortex generated by a plunging airfoil, and the effect of flexibility on the flow structure above a membrane airfoil. The specific cases were also selected to permit comparison with available experimental measurements. First, the process of transition on a stationary SD7003 airfoil section over a range of Reynolds numbers and angles of attack is considered. Prior to stall, the flow exhibits a separated shear layer which rolls up into spanwise vortices. These vortices subsequently undergo spanwise instabilities, and ultimately breakdown into fine-scale turbulent structures as the boundary layer reattaches to the airfoil surface. In a time-averaged sense, the flow displays a closed laminar separation bubble which moves upstream and contracts in size with increasing angle of attack for a fixed Reynolds number. For a fixed angle of attack, as the Reynolds number decreases, the laminar separation bubble grows in vertical extent producing a significant increase in drag. For the lowest Reynolds number considered (Re _c  = 10⁴), transition does not occur over the airfoil at moderate angles of attack prior to stall. Next, the impact of a prescribed high-frequency small-amplitude plunging motion on the transitional flow over the SD7003 airfoil is investigated. The motion-induced high angle of attack results in unsteady separation in the leading edge and in the formation of dynamic-stall-like vortices which convect downstream close to the airfoil. At the lowest value of Reynolds number (Re _c  = 10⁴), transition effects are observed to be minor and the dynamic stall vortex system remains fairly coherent. For Re _c  = 4 × 10⁴, the dynamic-stall vortex system is laminar at is inception, however shortly afterwards, it experiences an abrupt breakdown associated with the onset of spanwise instability effects. The computed phased-averaged structures for both values of Reynolds number are found to be in good agreement with the experimental data. Finally, the effect of structural compliance on the unsteady flow past a membrane airfoil is investigated. The membrane deformation results in mean camber and large fluctuations which improve aerodynamic performance. Larger values of lift and a delay in stall are achieved relative to a rigid airfoil configuration. For Re _c = 4.85 × 10⁴, it is shown that correct prediction of the transitional process is critical to capturing the proper membrane structural response.     

A parametric study of LES on laminar-turbulent transitional flows past an airfoil

Low-Reynolds-number aerodynamic performance of small-sized air vehicles is an area of increasing interest. In this study, low-Reynolds-number flows past an SD7003 airfoil are investigated to understand important viscous features of laminar separation and transitional flow followed by the complicated behavior of the flow reattachment process. In order to satisfy the three-dimensional (3D) requirement of the code, a simple “3D wing” is constructed from a two-dimensional (2D) airfoil. A parametric study of large eddy simulation (LES) on the airfoil flows at Re = 60,000 is performed. Effects of grid resolution and sub-grid scale (SGS) models are investigated. Although 3D effects cannot be accurately captured owing to the limitation of the grid resolution in the spanwise direction, the preliminary LES calculations do reveal some important flow characteristics such as leading-edge laminar separation and vortex shedding from the primary laminar separation bubble on the low-Reynolds-number airfoil.     

Reynolds number, thickness and camber effects on flapping airfoil propulsion

The effect of varying airfoil thickness and camber on plunging and combined pitching and plunging airfoil propulsion at Reynolds number Re=200, 2000, 20 000 and 2×10⁶ was studied by numerical simulations for fully laminar and fully turbulent flow regimes. The thickness study was performed on 2-D NACA symmetric airfoils with 6-50% thick sections undergoing pure plunging motion at reduced frequency k=2 and amplitudes h=0.25 and 0.5, and for combined pitching and plunging motion at k=2, h=0.5, phase ?=90°, pitch angle θ_o=15° and 30° and the pitch axis was located at 1/3 of chord from leading edge. At Re=200 for motions where positive thrust is generated, thin airfoils outperform thick airfoils. At higher Re significant gains could be achieved both in thrust generation and propulsive efficiency by using a thicker airfoil section for plunging and combined motion with low pitch amplitude. The camber study was performed on 2-D NACA airfoils with varying camber locations undergoing pure plunging motion at k=2, h=0.5 and Re=20 000. Little variation in thrust performance was found with camber. The underlying physics behind the alteration in propulsive performance between low and high Reynolds numbers has been explored by comparing viscous Navier-Stokes and inviscid panel method results. The role of leading edge vortices was found to be key to the observed performance variation.     

Validating the URANS shear stress transport γ −Reθ model for low‐Reynolds‐number external aerodynamics

A numerical investigation on low‐Reynolds‐number external aerodynamics was conducted using the transitional unsteady Reynolds‐averaged Navier–Stokes shear stress transport γ ?Re_θ model and the ANSYS‐CFX computational fluid dynamics suite. The NACA 0012 airfoil was exposed to chord‐based Reynolds numbers of 5.0 ×10⁴, 1.0 ×10⁵ and 2.5 ×10⁵ at 0°, 4°and 8°angles of attack. Time‐averaged and instantaneous flow features were extracted and compared with fully turbulent shear stress transport results, XFLR5 panel e ^N method results, and published higher order numerical and experimental studies. The current model was shown to reproduce the complex flow phenomena, including the laminar separation bubble dynamics and aerodynamic performance, with a very good degree of accuracy. The sensitivity of the model to domain size, grid resolution and quality, timestepping scheme, and free‐stream turbulence intensity was also presented. In view of the results obtained, the proposed model is deemed appropriate for modelling low‐Reynolds‐number external aerodynamics and provides a framework for future studies for the better understanding of this complex flow regime. Copyright © 2011 John Wiley & Sons, Ltd.     

Effect of flow regime change from subsonic to transonic on the air loads of an oscillating airfoil

In this research, the effect of flow regime change from subsonic to transonic on the air loads of a pitching NACA0012 airfoil is investigated. To do this, the effect of change in flow regime on the lift and pitching moment coefficients hysteresis cycles is studied. The harmonic balance approach is utilized for numerical calculation due to its low computational time. Verifications are also made with previous works and good agreements are observed. The assessment of flow regime change on the aforementioned hysteresis cycles is accomplished in the Mach number range of M=0.65–0.755. The reduced frequency and pitch amplitude also vary from k=0.03 to 0.1 and α₀=1–2.51°, respectively. Results show that the effect of increase in Mach number is to increase and decrease the lift coefficient during downstroke and upstroke, respectively, whereas at low reduced frequencies, the effect of increase in Mach number may lead to a reverse manner when airfoil moves toward its extremum angle of attack. Results also reveal that as the pitch amplitude varies, the shape of lift coefficient hysteresis cycle depends more on the pitch amplitude than on the appearance of shock. It is shown that as the Mach number increases, the incidence angles correspond to the extremum pitching moment, and depending on the reduced frequency, lie between zero and extremum angle of attack. These incidence angles shift toward the extremum angle of attack as the reduced frequency decreases. Results also show that the increase in pitch amplitude at low Mach number, in such a way that leads to the formation of shock around the extremum angle of attack, causes the extremum pitching moment to appear around these angles and at high Mach number, depending on the reduced frequency, the extremum pitching moment incidence angles would be between zero and extremum incidence angle.     

Influence of pitching angle of incidence on the dynamic stall behavior of a symmetric airfoil

This study presents the influence of pitch angle of an airfoil on its near-field vortex structure as well as the aerodynamic loads during a dynamic stall process. Dynamic stall behavior in a sinusoidally pitching airfoil is usually analyzed at low to medium reduced frequencies and with the maximum angle of attack of the airfoil not exceeding 25°. In this work, we study dynamic stall of a symmetric airfoil at medium to high reduced frequencies even as the maximum angle of attack goes from 25° to 45°. The evolution and growth of the laminar separation bubble, also known as a dynamic stall vortex, at the leading edge and the trailing edge are studied as the pitch cycle goes from the minimum to the maximum angle of attack. The effect of reduced frequencies on the vortex structure as well as the aerodynamic load coefficients is investigated. The reduced frequency is shown to be a bifurcation parameter triggering period doubling behavior. However, the bifurcation pattern is dependent on the variation of the pitch angle of incidence of the airfoil.     

Experimental study of pitching and plunging airfoils at low Reynolds numbers

Measurements of the unsteady flow structure and force time history of pitching and plunging SD7003 and flat plate airfoils at low Reynolds numbers are presented. The airfoils were pitched and plunged in the effective angle of attack range of 2.4°–13.6° (shallow-stall kinematics) and ?6° to 22° (deep-stall kinematics). The shallow-stall kinematics results for the SD7003 airfoil show attached flow and laminar-to-turbulent transition at low effective angle of attack during the down stroke motion, while the flat plate model exhibits leading edge separation. Strong Re-number effects were found for the SD7003 airfoil which produced approximately 25 % increase in the peak lift coefficient at Re = 10,000 compared to higher Re flows. The flat plate airfoil showed reduced Re effects due to leading edge separation at the sharper leading edge, and the measured peak lift coefficient was higher than that predicted by unsteady potential flow theory. The deep-stall kinematics resulted in leading edge separation that led to formation of a large leading edge vortex (LEV) and a small trailing edge vortex (TEV) for both airfoils. The measured peak lift coefficient was significantly higher (~50 %) than that for the shallow-stall kinematics. The effect of airfoil shape on lift force was greater than the Re effect. Turbulence statistics were measured as a function of phase using ensemble averages. The results show anisotropic turbulence for the LEV and isotropic turbulence for the TEV. Comparison of unsteady potential flow theory with the experimental data showed better agreement by using the quasi-steady approximation, or setting C(k) = 1 in Theodorsen theory, for leading edge–separated flows.     

Aeroelastic response of an airfoil to gusts: Prediction and control strategies from computed energy maps

A method to predict the aeroelastic pitch response of an airfoil to gusts is presented. The prediction is based on energy maps generated by high-fidelity fluid dynamic simulations of the airfoil with prescribed pitch oscillations. The energy maps quantify the exchange of energy between the pitching airfoil and the flow, and serve as manifolds over which the dynamical states of aeroelastic airfoil system grow, decay and attain stationary states. This method allows us to study the full nonlinear response of the system to large gusts, and predict the growth and saturation of aeroelastic pitch instabilities. We also show that the manifold topology in these maps can be used to make informed modifications to the system parameters in order to control the response to gusts.     

Direct numerical simulation of a NACA0012 in full stall

This work aims at investigating the mechanisms of separation and the transition to turbulence in the separated shear-layer of aerodynamic profiles, while at the same time to gain insight into coherent structures formed in the separated zone at low-to-moderate Reynolds numbers. To do this, direct numerical simulations of the flow past a NACA0012 airfoil at Reynolds numbers Re = 50,000 (based on the free-stream velocity and the airfoil chord) and angles of attack AOA = 9.25° and AOA = 12° have been carried out. At low-to-moderate Reynolds numbers, NACA0012 exhibits a combination of leading-edge/trailing-edge stall which causes the massive separation of the flow on the suction side of the airfoil. The initially laminar shear layer undergoes transition to turbulence and vortices formed are shed forming a von Kármán like vortex street in the airfoil wake. The main characteristics of this flow together with its main features, including power spectra of a set of selected monitoring probes at different positions on the suction side and in the wake of the airfoil are provided and discussed in detail.     

Comparative Analysis of the Characteristics of the Vortex Wake behind a Flapping Wing Performing Oscillations of Different Types

The wake characteristics of a custom-designed airfoil performing pitching oscillations, heaving oscillations, and a combination of pitch and heave oscillations are compared in this study. The influence of flapping parameters are investigated at a constant Reynolds number Re\(_{c} = 2640\) and is presented for the Strouhal numbers based on the oscillation amplitude, St_A, varying in the \(0.1 \leqslant {\text{S}}{{{\text{t}}}_{A}} \leqslant 0.4\) range. The generation of vorticity above and below the airfoil depends on the airfoil’s initial direction of motion and remains the same for all types of flapping oscillations investigated. The evolution of the leading-edge and trailing-edge vortices is presented. The heaving oscillations of the airfoil are found to have a greater influence on the characteristics of the leading edge vortex. The wake behind the combined pitch-heave oscillations appears to be governed by pitching oscillations below \({\text{S}}{{{\text{t}}}_{A}} = 0.24\), whereas it is driven by heaving oscillations above \({\text{S}}{{{\text{t}}}_{A}} = 0.24\). The force computations indicate that the mere existence of the reverse von Kármán street is not sufficient to develop the thrust on the airfoil. The periodic component of velocity fluctuations significantly influences the wake characteristics. The anisotropic stress field developed around the airfoil due to the periodic fluctuations of the velocity is presented. The coherent structures developed in the wake are identified using the proper orthogonal decomposition and a qualitative comparison of the structures for different flapping oscillations is presented. The energy transfer from the flapping airfoil to the fluid for different flapping oscillations is highest for heaving oscillations followed by combined pitch-heave oscillations and pitching oscillations.

     

The ultra-low Reynolds number airfoil wake

Lift force and the near wake of an NACA 0012 airfoil were measured over the angle (α) of attack of 0°–90° and the chord Reynolds number (Re _c ), 5.3 × 10³–5.1 × 10⁴, with a view to understand thoroughly the near wake of the airfoil at low- to ultra-low Re _c . While the lift force is measured using a load cell, the detailed flow structure is captured using laser-Doppler anemometry, particle image velocimetry, and laser-induced fluorescence flow visualization. It has been found that the stall of an airfoil, characterized by a drop in the lift force, occurs at Re _c  ≥ 1.05 × 10⁴ but is absent at Re _c  = 5.3 × 10³. The observation is connected to the presence of the separation bubble at high Re _c but absence of the bubble at ultra-low Re _c , as evidenced in our wake measurements. The near-wake characteristics are examined and discussed in detail, including the vortex formation length, wake width, spanwise vorticity, wake bubble size, wavelength of K–H vortices, Strouhal numbers, and their dependence on α and Re _c .     

Spectrographic analysis for the modal testing of nonlinear aeroelastic systems

The spectrograph is a signal-processing tool often used for the frequency domain analysis of time-varying signals. When the signal to be analyzed is a function of time, the spectrograph represents the frequency content of the signal as a sequence of power spectra that change with time. In this paper, the usefulness of the technique is demonstrated in its application to the analysis of the time history response of a nonlinear aeroelastic system. The aeroelastic system is modelled analytically as a two-dimensional, rigid airfoil section free to move in both the bending and pitching directions and possessing a rigid flap. The airfoil is mounted by torsional and translational springs attached at the elastic axis, and the flap is used to provide the forcing input to the system. The nonlinear system is obtained by introducing a freeplay type of nonlinearity in the pitch degree-of-freedom restoring moment. The airfoil is immersed in an aerodynamic flow environment, modelled using incompressible thin airfoil theory for unsteady oscillatory motion. The equations of motion are solved using a fourth-order Runge–Kutta numerical integration technique to provide time-history solutions of the response of the airfoil in the pitch and plunge directions. Time-histories are obtained for the nonlinear responses of the linear and nonlinear aeroelastic systems to a sine-sweep input. The time-histories are analyzed using the spectrographic technique, and the frequency content of the response is plotted directly as a function of the input frequency. Results show that the combination of the sine-sweep input with the spectrographic analysis permits a unique insight into the behavior of the nonlinear system with a minimum of testing. It is shown that the frequency of the nonlinear system response is a function of the input frequency and one other characteristic frequency that can be associated with the limit cycle oscillations of the same nonlinear system subject to a transient input.     

Lift enhancement and flow structure of airfoil with joint trailing-edge flap and Gurney flap

The impact of Gurney flaps (GF), of different heights and perforations, on the aerodynamic and wake characteristics of a NACA 0015 airfoil equipped with a trailing-edge flap (TEF) was investigated experimentally at Re = 2.54 × 10⁵. The addition of the Gurney flap to the TEF produced a further increase in the downward turning of the mean flow (increased aft camber), leading to a significant increase in the lift, drag, and pitching moment compared to that produced by independently deployed TEF or GF. The maximum lift increased with flap height, with the maximum lift-enhancement effectiveness exhibited at the smallest flap height. The near wake behind the joint TEF and GF became wider and had a larger velocity deficit and fluctuations compared to independent GF and TEF deployment. The Gurney flap perforation had only a minor impact on the wake and aerodynamics characteristics compared to TEF with a solid GF. The rapid rise in lift generation of the joint TEF and GF application, compared to conventional TEF deployment, could provide an improved off-design high-lift device during landing and takeoff.     

A transition phenomenon of ice formation in water flow between two horizontal parallel plates

Experiments have been performed to investigate the icetransition profiles and heat-transfer characteristics for water flows between two horizontal parallel plates. The experiments are carried out under the condition that upper plate is cooled at uniform temperature kept less than freezing temperature of water, while the lower plate is heated at uniform temperature kept higher than the temperature of water flow. The temperatures of the upper and lower plates range from ?8 to ?14°C and from 10 to 60 °C, respectively, with inlet-water temperature varied from 1.5 to 4.5 °C. The cooling and heating temperature ratios, θ_c and θ_h, are ranging from 1.78 to 9.33 and from 1.22 to 39, respectively. By using three kinds of heightH of 16, 30 and 40 mm between the horizontal parallel plates, the Reynolds and Grashof numbers are varied from 3.2 × 10² to 1.5 × 10⁴ and from 3.4 × 10³ to 8.97 × 10⁶, respectively. As a result of this investigation two ice-transition modes are observed. The first ice-transition mode is due to an interruption of upper and lower thermal boundary layers, while the second mode is due to an instability of laminar boundary layer formed on water-ice interface. In order to determine the kind of ice-transition mode, criterion correlation formulas including the Reynolds numberRe _H , Grashof numberGr _H , and heating temperature ratio θ_h are determined and may be written as follows: For thermal icetransition mode (th.I.T.M.)Re _H /(Gr _H ·θ _h )^0.23<1.6×10^?3 and for hydrodynamical ice-transition mode (hy.I.T.M.)Re _H /(Gr _H ·θ _h )^0.23>2.3×10^?3 By introducing the freezing parameterB _f , correlation equations for local and mean Nusselt numbers along the water-ice interface at steady-state condition are determined. From the current experimental results it is found that the local Nusselt number may be described as the following equation:Nu _x =0.835 Re _H ^0.278 · B _f ^0.834 ·x/H)^?0.139     

Scanning PIV investigation of the laminar separation bubble on a SD7003 airfoil

A laminar separation bubble occurs on the suction side of the SD7003 airfoil at an angle of attack α =  4–8° and a low Reynolds number less than 100,000, which brings about a significant adverse aerodynamic effect. The spatial and temporal structure of the laminar separation bubble was studied using the scanning PIV method at α =  4° and Re = 60,000 and 20,000. Of particular interest are the dynamic vortex behavior in transition process and the subsequent vortex evolution in the turbulent boundary layer. The flow was continuously sampled in a stack of parallel illuminated planes from two orthogonal views with a frequency of hundreds Hz, and PIV cross-correlation was performed to obtain the 2D velocity field in each plane. Results of both the single-sliced and the volumetric presentations of the laminar separation bubble reveal vortex shedding in transition near the reattachment region at Re = 60,000. In a relatively long distance vortices characterized by paired wall-normal vorticity packets retain their identities in the reattached turbulent boundary layer, though vortices interact through tearing, stretching and tilting. Compared with the restricted LSB at Re = 60,000, the flow at Re = 20,000 presents an earlier separation and a significantly increased reversed flow region followed by “huge” vortical structures.     

An experimental investigation of the ELAC 1 configuration at supersonic speeds

Supersonic flight of aerospace planes is of marked interest since several flow regimes characterized by different local flow structures have to be flown through. This problem was investigated experimentally for the hypersonic research configuration ELAC 1. The aim of the study was to detect the influence of the rounded leading edge, of the thickness distribution prescribed, and of the Reynolds number, especially on the flow on the leeward side of the configuration. The experiments were carried out in the transonic wind tunnel of Aerodynamisches Institut of RWTH Aachen, at a freestream Mach number Ma _∞=2, a unit Reynolds number of Re _∞=13×10⁶, angles of attack between ?3°?α?10°, and in a wind tunnel of the Institute for Theoretical and Applied Mechanics of the Russian Academy of Sciences in Novosibirsk. The freestream Mach numbers covered in these experiments were varied between 2?Ma _∞?4, freestream Reynolds numbers per unit length between 25×10⁶?Re _∞?56×10⁶ and angles of attack between ?3°?α?10°. Flow visualization studies, measurements of surface pressure distributions and of aerodynamic forces were used to analyze the flow. The results, which will also be compared with numerical data, clearly indicate marked differences in the location of the separation and reattachment lines, and the formation of the primary, secondary and tertiary vortices, for the flow regimes investigated.     

Numerical investigations into the asymmetric effects on the aerodynamic response of a pitching airfoil

The effects of asymmetric sinusoidal motion on pitching airfoil aerodynamics were studied by numerical simulations for 2-D flow around a NACA0012 airfoil at Re=1.35×10⁵. Various unsteady parameters (amplitude of oscillation, d; reduced frequency, k) were applied to investigate the effect of asymmetry parameter S on the instantaneous force coefficients and flow patterns. The results reveal that S has a noticeable effect on the aerodynamic performance, as it affects the instantaneous force coefficient, maximum lift and drag coefficient, hysteresis loops and the flow structures.