Flow injection spectrophotometric determination of iron(III) using diphenylamine-4-sulfonic acid sodium salt

A highly sensitive and very simple spectrophotometric flow-injection analysis (FIA) method for the determination of iron(III) at low concentration levels is presented. The method is based on the measurement of absorbance intensity of the red complex at 410 nm formed by iron(III) and diphenylamine-4-sulfonic acid sodium salt (DPA-4-SA). It is a simple, highly sensitive, fast, and low cost alternative method using the color developing reagent DPA-4-SA in acetate buffer at pH 5.50 and the flow-rate of 1 mL min⁻¹ with the sample throughput of 60 h⁻¹. The method provided a linear determination range between 5 μg L⁻¹ and 200 μg L⁻¹ with the detection limit (3S) of 1 μg L⁻¹ of iron(III) using the injection volume of 20 μL. FIA variables influencing the system performance were optimized. The amount of iron(III) and total iron in river and seawater samples was successfully determined. Repeatability of the measurements was satisfactory at the relative standard deviation of 3.5 % for 5 determinations of 10 μg L⁻¹ iron(III). The accuracy of the method was evaluated using the standard addition method and checked by the analysis of the certified material Std Zn/Al/Cu 43 XZ3F.     

流动注射化学发光法测定肉桂酸

碱性条件下,肉桂酸对Luminol-H2O2-纳米银化学发光体系有较强的增敏作用,据此,结合流动注射技术,建立了测定肉桂酸的新方法。该法线性范围为2.5×10-8～2.5×10-6mol/L,检出限为6.0×10-9mol/L,对1.0×10-7 mol/L的肉桂酸平行测定9次,相对标准偏差为2.5%。该法可用于尿液中肉桂酸的测定。     

Reverse flow injection spectrophotometric determination of iron(III) using norfloxacin

A reversed flow injection colorimetric procedure for determining iron(III) at the μg level was proposed. It is based on the reaction between iron(III) with norfloxacin (NRF) in 0.07 mol l⁻¹ ammonium sulfate solution, resulting in an intense yellow complex with a suitable absorption at 435 nm. Optimum conditions for determining iron(III) were investigated by univariate method. The method involved injection of a 150 μl of 0.04% w/v colorimetric reagent solution into a merged streams of sample and/or standard solution containing iron(III) and 0.07 mol l⁻¹ ammonium sulfate in sulfuric acid (pH 3.5) solution which was then passed through a single bead string reactor. Subsequently the absorbance as peak height was monitored at 435 nm. Beer's law obeyed over the range of 0.2–1.4 μg ml⁻¹ iron(III). The method has been applied to the determination of total iron in water samples digested with HNO₃–H₂O₂ (1:9 v/v). Detection limit (3σ) was 0.01 μg ml⁻¹ the sample through of 86 h⁻¹ and the coefficient of variation of 1.77% (n=12) for 1 μg ml⁻¹ Fe(III) were achieved with the recovery of the spiked Fe(III) of 92.6–99.8%.     

Reverse flow injection spectrophotometric determination of iron(III) using chlortetracycline reagent

A simple reversed flow injection colourimetric procedure for determining iron(III) was proposed. It is based on the reaction between iron(III) with chlortetracycline, resulting in an intense yellow complex with a suitable absorption at 435 nm. A 200 μl chlortetracycline reagent solution was injected into the phosphate buffer stream (flow rate 2.0 ml min⁻¹) which was then merged with iron(III) standard or sample in dilute nitric acid stream (flow rate 1.5 ml min⁻¹). Optimum conditions for determining iron(III) were investigated by univariate method. Under the optimum conditions, a linear calibration graph was obtained over the range 0.5–20.0 μg ml⁻¹. The detection limit (3σ) and the quantification limit (10σ) were 0.10 and 0.82 μg ml⁻¹, respectively. The relatives standard deviation of the proposed method calculated from 12 replicate injections of 2.0 and 10.0 μg ml⁻¹ iron(III) were 0.43 and 0.59%, respectively. The sample throughput was 60 h⁻¹. The proposed method has been satisfactorily applied to the determination of iron(III) in natural waters.     

Flow injection spectrofluorimetric determination of carvedilol mediated by micelles

We propose a novel evanescent wave scattering imaging method using an objective-type total internal reflection system to image and track single gold nanoparticles (GNPs) in solution. In this imaging system, only a millimeter-scale hole is employed to efficiently separate GNPs scattering light from the background reflected beam. The detailed experimental realization of the imaging system was discussed, and the effect of the hole size on imaging was investigated. We observed that the hole diameters from 2.5 to 4 mm are suitable to perform the scattering imaging by adjusting the incidence angle. The technology was successfully applied to track single gold nanoparticles in solution and on live cell membrane via the anti-epidermal growth factor receptor antibody. Compared to total internal fluorescence microscopy, the resonance light scattering detection has no photobleaching or blinking inherent to fluorescent dyes and quantum dots. Compared to conventional dark-field microscopy, the evanescent wave illumination can be conveniently applied to study membrane dynamics in living cells. Additionally, the objective-based configuration provides a free space above the coverslip, and allows imaging and concomitant manipulation of live cells in culture by microinjection, patch-clamping, AFM and other techniques.     

Simultaneous spectrofluorimetric determination of cerium(III) and cerium(IV) by flow injection analysis

Cerium(III) (1–100 μg l^?1) is determined by injection into a carrier stream of hydrochloric, perchloric or sulphuric acid, and monitoring its native fluorescence. Cerium(IV) can be determined similarly by incorporating a zinc reductor minicolumn into the system. Splitting the injection sample so that only part passes through the reductor, and the remainder by-passes it, allows total cerium and cerium(III) to be detected from the two sequential fluorescence peaks obtained.     

流动注射光度法测定痕量铁

水 乙醇混溶介质中Fe(Ⅲ)与2 (5 溴 2 吡啶偶氮) 5 二乙氨基苯酚(5 Br PADAP)的显色反应已有用于流动注射的报道[1 2],本文利用稀盐酸的增敏作用,在较低的显色剂浓度和乙醇用量条件下,无需加入乳化剂增溶,采用显色剂与缓冲溶液预先混合,以去离子水为推动液,用正交设计法优化各实验参数,优选出了最佳的组合方案。该方法的线性范围为20μg/L-1200μg/L,相对标准偏差为0 5%。将该方法用于水样实际测定,效果满意。方法的检测限优于已有的报道。1　实验部分1 1　主要仪器与试剂ZJ 2低压过渡金属离子色谱仪(将分离柱用聚四氟乙烯管代替,…     

Repetitive determination of ascorbic acid using iron(III)-1.10-phenanthroline-peroxodisulfate system in a circulatory flow injection method

Ascorbic acid (AA) could be determined in large quantities of a co-existing oxidant. The incorporation of an on-line reagent regeneration step based on redox reaction eliminates the baseline drift in the procedure. This makes it possible to adopt a circulatory flow injection method (cyclic FIA) and to determine AA repetitively. The method is based on the reduction of iron(III) to iron(II) by the analyte, the reaction of the produced iron(II) with 1,10-phenanthroline (phen) in a weak acidic medium to form a colored complex, and the subsequent oxidation reaction of iron(II) to iron(III) by the co-existing peroxodisulfate. A solution (50 ml) of 3.0×10⁻⁴ mol l⁻¹ ferric chloride, 9.0×10⁻⁴ mol l⁻¹ phen and 5.0×10⁻² mol l⁻¹ ammonium peroxodisulfate in acetate buffer (0.2 mol l⁻¹, pH 4.5) is continuously circulated at a constant flow rate of 1.0 ml min⁻¹. Into this stream, an aliquot (20 μl) of the sample solution containing AA is quickly injected by means of a six-way valve. The complex formed is monitored spectrophotometrically (at 510 nm) in the flow system. The stream then returns to the reservoir after passing through a time-delay coil (50 m). The iron(II)–(phen)₃ complex is oxidized to iron(III)–(phen)₃ complex by peroxodisulfate which exists excessively in the circulating reagent solution. The proposed method allows as many as 300 repetitive determinations of 15 mg l⁻¹ AA with only 50 ml reservoir solution. The contents of AA in commercial pharmaceutical products were analyzed to demonstrate the capability of the developed system.     

Flow injection kinetic spectrofluorimetric determination of trace amounts of osmium

A flow injection (FI) kinetic spectrofluorimetric method is described for the determination of osmium(IV) and the possible mechanism of catalytic reaction is discussed. The method is based on the fluorescence enhancing reaction of o-vanillin furfuralhydrazone (OVFH) with potassium bromate, which is catalyzed by Os(IV) in water medium at pH 6.10 and 45 degrees C. OVFH is newly synthesized and its ionization, IR and elemental analysis are established. Under these experimental conditions, the oxidized product of OVFH has excitation and emission maxima at 337 and 490 nm, respectively. The linear range of this method is 0-600 ng ml(-1) with the R.S.D. of 1.2%. The detection limit is 1.0 ng ml(-1) of Os(IV). A high analysis rate of 24 samples h(-1) is obtained by the FI method. The proposed method is applied successfully to determine Os(IV) in synthetic mixture and mineral samples, and the results are well consistent with the standard values.     

Use of acetohydroxamic acid in the direct spectrophotometric determination of iron(III) and iron(II) by flow injection analysis

The direct spectrophotometric determination of iron(III) and iron(II) by flow injection analysis with acetohydroxamic acid and 1,10-phenanthroline as reagents is reported. The working ranges are 0.5–10 and 10–60 mg l^?1, respectively. Results obtained for synthetic mixtures of Fe(III) and Fe(II) and for acid extracts of haematite samples were accurate. Interference studies indicate that the method is highly selective.     

Flow injection determination of chromium(III) by pyrogallol chemiluminescence

A flow injection method is proposed for the determination of nanogram amounts of chromium(III) using a pyrogallol chemiluminescence system. It is based on its catalytic effect on the oxidation of pyrogallol with periodate at a neutral medium. The addition of 3-(N-morpholino)propanesulphonic acid to the reaction system increased the chemiluminescence signal for chromium(III). The present method allows the determination of 5-100ng/ml of chromium(III). The relative standard deviation of 2.2% (n = 10) was obtained at 20 ng/ml of chromium(III) and the detection limit (signal-to-noise ratio = 2) was 1 ng/ml with the sampling frequency of 25/hr.     

Determination of iron(III) with salicylic acid by the fluorescence quenching method

The spectrofluorimetric determination of Fe³⁺ using salicylic acid as an emission reagent has been investigated by measuring the decrease of fluorescence intensity of salicylic acid due to the complexation of Fe³⁺–salicylic acid. An emission peak of salicylic acid, which is decreased linearly by addition of Fe³⁺, occurs at 409 nm in aqueous solution with excitation at 299 nm. The determination of the ferric ion is in the range 1×10⁻⁶–10×10⁻⁶ M Fe³⁺ (0.0558–0.558 μg/ml) and the detection limit is 5×10⁻⁸ M. The quenching effect of Fe³⁺ on the fluorescence intensity of salicylic acid may be considered on the basis of complexation between salicylic acid and Fe³⁺. The effects of foreign ions were investigated.     

Spectrophotometric method for determination of sulfide with iron(III) and nitrilotriacetic acid by flow injection

A manual colorimetric method for determination of sulfide has been adapted to flow injection, systematically optimized, and more fully characterized. Its intended application is for measurement of sodium sulfide reagent strength in pulp process streams, and sulfide contamination in effluent from Kraft pulp mills. In the flow-injection method developed, a sample solution containing sulfide is reacted with a mixture of iron(III) and nitrilotriacetic acid under ammoniacal conditions. The absorbance of the intensely-colored green product of this reaction is measured at 636 nm. Excess sulfite is present as a color stabilizer. A linear dynamic range of 20-100 ppm sulfide is readily achieved; the relative standard deviation is less than 1.2% (n = 10) throughout this range, and 0.37% (n = 10) midrange at 60 ppm. The usable dynamic range is 8-250 ppm sulfide. Long-term stability of the method is ensured by periodically performing an automatic cleaning cycle using a hydrochloric acid wash solution. This prevents tube discoloration and removes any precipitates which are formed under strongly alkaline conditions. The sample throuhput rate is at least 30/hr, given alternate acid wash cycles.     

Spectrophotometric determination of iron(III) and total iron by sequential injection analysis technique

A procedure for determination of concentrations of iron(III) and total iron by sequential injection analysis is described. The method is based on the strong blue-colored complexes formed between iron(III) and tiron. The absorbance of the complexes is measured spectrophotometrically at 635 nm. Oxidation of iron(II) and masking of interfering fluoride is simultaneously done by injecting one zone of hydrogen peroxide and one of thorium(IV) between the sample and reagent zones. Concentration of iron(III) and total iron, in the range 0.002–0.026 M, in diluted samples from a pickle bath were determined. The relative standard deviation was 0.4% (n=7). The method was also used in a pilot plant of a zinc process for determination of iron(III) in the range 0.2–3.0 g l⁻¹. The sample throughput is approximately 17 samples per hour, including three repetitive determinations of each sample.     

A simple flow injection spectrophotometric determination method for iron(III) based on O-acetylsalicylhydroxamic acid complexation

A simple and rapid flow-injection spectrophotometric method for the determination of iron(III) and total iron is proposed. The method is based on the reaction between iron(III) and O-acetylsalicylhydroxamic acid (AcSHA) in a 2 % methanol solution resulting in an intense violet complex with strong absorption at 475 nm. Optimum conditions for the determination of iron(III) and the interfering ions were tested. The relative standard deviation for the determination of 5 μg L⁻¹ iron(III) was 0.85 % (n = 10), and the limit of detection (blank signal plus three times the standard deviation of the blank) was 0.5 μg L⁻¹, both based on the injection volumes of 20 μL. The method was successfully applied in the determination of iron(III) and total iron in water and ore samples. The method was verified by analysing a certified reference material Zn/Al/Cu 43XZ3F and also by the AAS method.     

Catalytic-fluorimetric determination of EDTA and iron(III) by flow injection analysis

Summary In this paper the authors report on several methods for the direct determination of EDTA and indirect determination of iron(III), based on the inhibition effect of EDTA on the catalytic action of copper (II) on the oxidation of 2,2-dipyridyl ketone hydrazone by hydrogen peroxide and on the decrease of this inhibition effect in the presence of Fe(III), respectively. These methods allow the determination of EDTA in the ranges of 0.4–2.0 g · ml^–1 and 0.2–1.0 g · ml^–1 for the normal and reversed FIA modes, respectively, and of 40–240 ng · ml^–1 for Fe(III) by reversed FIA.

---

Katalytisch-fluorimetrische Bestimmung von EDTA und Eisen(III) durch FließinjektionsanalyseInhibitionsmethoden

Zusammenfassung Verfahren zur direkten Bestimmung von EDTA sowie zur indirekten Bestimmung von Eisen(III) werden beschrieben. Sie beruhen auf der Inhibitorwirkung von EDTA auf den katalytischen Effekt von Kupfer(II) bei der Oxidation von 2,2-Dipyridylketonhydrazon mit Wasserstoffperoxid bzw. auf der Schwächung dieser Inhibitorwirkung in Gegenwart von Eisen(III). Es ist mit diesen Methoden möglich, EDTA im Bereich von 0,4–2,0 g/ml (normale FIA) bzw. 0,2–1,0 g/ml (umgekehrte FIA) und Eisen im Bereich von 40–240 ng/ml (umgekehrte FIA) zu bestimmen.

     

Sensitive spectrofluorimetric determination of aluminium(III) with Eriochrome Red B

A spectrofluorimetric method is reported for the determination of Al(III), based on the formation of a fluorescent Al(III)-Eriochrome Red B complex in the presence of hexamethylenetetramine at 60°C. Fluorescence measurements were made at 2°C and all variables that affect the development of the complex are reported. The method is very selective and the detection limit is 0.1 ng ml^?1. It was applied to the determination of Al(III) in tap water.