由硅酸酯合成单分散二氧化硅中碳的化学形态

单分散二氧化硅是指尺寸分布十分狭窄的二氧化硅颗粒．单分散颗粒在科学研究及工业应用中得到了广泛的应用［1］．单分散二氧化硅由正硅酸有机酯在氨催化下于醇溶液中水解缩合得到．硅酸酯的水解和缩合反应可用如下反应描述．总的反应式为：nSi（OR）4＋2nH20→nSiO2＋4nROH1956年Kolbe［2］发现正硅酸乙酯（TEOS）在碱催化下于乙醇溶剂中水解反应有时会形成均一颗粒二氧化硅以来，许多学者对这一反应体系进行了较为广泛的研究，提出了双分子缩合成核机理、单分子叠加生长机理、表面反应控制生长机理、扩散控制生长机理和微晶核团聚生…     

Effect of solvent type on polycondensation of TEOS catalyzed by DBTL as used for stone consolidation

We have investigated the effect of solvent in the sol–gel process of tetraethylorthosilicate (TEOS) when di-n-butyltin dilaurate (DBTL) is used as polycondensation catalyst. Two sets of materials similar to those employed in the field of stone consolidation were prepared in the laboratory by using either protic or aprotic solvents: (1) xerogels from TEOS/DBTL, and (2) composites from TEOS/colloidal silica particles/DBTL. The results have shown that the solvent directly influences the aggregation pathway of the condensates. For a mixture of methyl ethyl ketone/acetone (aprotic solvents), gels with a higher degree of condensation were obtained. In the case of TEOS xerogels, the materials are essentially non-porous. Additionally, the incorporation of colloidal silica particles induces an important increase in porosity, which is even more dramatic when ethanol is used as solvent, through the formation of micro and mesoporous materials as the concentration of particles is increased. A TEOS polymerization pathway is suggested depending on which system of solvents is used. Various analytical techniques were used to characterize the materials obtained.     

Preparation and Properties of Aramid-Silica Hybrids with Inter-Phase Bonding Through (3-glycidoxypropyl)-trimethoxysilane

Nano-composites from aramid-silica system have been prepared via sol-gel process. Poly (phenyleneterephthalamide) copolymer chains were prepared by reacting a mixture of p- and m-phenylenediamines with terephthaloyl chloride in dimethylacetamide used as solvent. The sol-gel process in the polymer matrix was carried out through hydrolysis and condensation of a mixture of tetraethoxysilane and (3-glycidoxypropyl) trimethoxysilane. The latter was used to develop linkage, on one hand with silica network structure using alkoxy groups and on the other hand with aramid chains at its secondary amine groups through glycidal groups of silane. Mutual interaction between the two disparate phases aramid and silica network was thus created. Thin films of the composites containing different proportions of silica ranging from 5.0 to 25.0-wt% were cast by the solvent elution technique. The α-relaxation temperature associated with the glass transition was measured by the dynamic mechanical thermal analysis. The results showed an increase in the glass transition temperature from 328°C for the pure aramid to 352°C for the hybrid materials containing 25-wt% silica, an indicative of the increased interfacial interaction between the two phases. Films having relatively low silica content were flexible and transparent, but those with high silica content were opaque and brittle. These films were tested for their tensile strength, modulus and toughness. The mechanical strength of the composites as compared to the pure aramid increased initially but with further addition of silica the strength decreased. The initial increase can be explained due to increased interfacial interaction between the two phases, however agglomeration of silica particles was responsible for decreasing strength at higher silica contents.     

Fractal Characterization of Silica Sol Prepared by the Sol-Gel Method: From the Sol Formation to the Flocculation Process

The fractal characterization of silica particles prepared by the sol-gel method was obtained; from the beginning of the sol-gel synthesis to the aggregation process of these particles by adding metal ions in solution, the fractal dimension was determined. At the beginning of the sol-gel process, unstable structures were formed due, essentially, to the auto-catalytic nature of the sol-gel condensation reactions; these particles are fractal structures with a fractal exponent corresponding to a reaction limited aggregation regime. As the time proceeds, the reactants are consumed approaching the system to equilibrium, stabilizing the size of the silica particles. The silica sol can be flocculated by adding metal ions in solution. The fractal exponent for the aggregation process was determined, obtaining a value corresponding to a diffusion limited aggregation regime.     

Parts per quadrillion level ultra-trace determination of polar and nonpolar compounds via solvent-free capillary microextraction on surface-bonded sol-gel polytetrahydrofuran coating and gas chromatography-flame ionization detection

Sol-gel polytetrahydrofuran (poly-THF) coating was developed for high-sensitivity sample preconcentration by capillary microextraction (CME). Parts per quadrillion (ppq) level detection limits were achieved for both polar and nonpolar analytes through sample preconcentration on sol-gel poly-THF coated microextraction capillaries followed by gas chromatography (GC) analysis of the extracted compounds using a flame ionization detector (FID). The sol-gel coating was in situ created on the inner walls of a fused silica capillary using a sol solution containing poly-THF as an organic component, methyltrimethoxysilane (MTMOS) as a sol-gel precursor, trifluoroacetic acid (TFA, 5% water) as a sol-gel catalyst, and hexamethyldisilazane (HMDS) as a deactivating reagent. The sol solution was introduced into a hydrothermally-treated fused silica capillary and the sol-gel reactions were allowed to take place inside the capillary for 60 min. A wall-bonded coating was formed due to the condensation of silanol groups residing on the capillary inner surface with those on the sol-gel network fragments evolving in close vicinity of the capillary walls. Poly-THF is a medium polarity polymer, and was found to be effective in carrying out simultaneous extraction of both polar and nonpolar analytes. Efficient extraction of a wide range of trace analytes from aqueous samples was accomplished using sol-gel poly-THF coated fused silica capillaries for further analysis by GC. The test analytes included polycyclic aromatic hydrocarbons (PAHs), aldehydes, ketones, chlorophenols, and alcohols. To our knowledge, this is the first report on the use of a poly-THF based sol-gel material in analytical microextraction. Sol-gel poly-THF coated CME capillaries showed excellent solvent and thermal stability (>320 degrees C).     

Composite of SiO2 and Hydrogel Having Microphase Separated Structure: Physical Properties Dependence on pH

Abstract

Organic-inorganic composite gel was prepared by using PEG-modified urethane acrylate (PMUA) gel and tetraethoxysilane (TEOS). PMUA gel was prepared by the phase-inversion emulsion polymerization of PMUA emulsion. The gelation of PMUA emulsion using this method enables PMUA gel to swell with H₂O, TEOS, and ethanol. Hydrolysis and condensation reaction rates of the sol-gel process are strongly influenced by the pH controlled by catalysts such as HCl and NH₄OH. Additionally, the morphology on the cross section of composite and the amount of silica ingredient incorporated into the composite gel were dependent on solvent, the molar ratio of H₂O to TEOS, as well as the pH value.

As the silica content increased, due to hydrogen bonds interacting between PMUA gel and SiO₂, particles, the tensile strength of composites considerably increased, whereas the elongation at break decreased. The incorporation of silica ingredient in PMUA gel/silica composites was verified with FTIR/ATR and SEM. The amount of the silica component in the composite was indirectly investigated by using TGA thermal analysis.     

Synthesis of acrylic-modified sol–gel silica

Silica was obtained by sol–gel process through hydrolysis and condensation of tetraethyl orthosilicate (TEOS) using molar fraction of H₂O/TEOS=9 under alkaline catalysis, at different reaction times (5 min to 24 h). At the end of each time, the reaction medium appeared as a suspended microparticle system. After solvent evaporation, the yield was calculated to be around 100% and practically independent of the time of reaction. The silica had its surface modified through the condensation reaction with acryloyl chloride forming organically modified silica. The unmodified and modified silica were characterized by thermogravimetry and derivative thermogravimetry (TG/DTG), infrared spectrometry (FT-IR), size particle and optical microscopy (OM). The acrylic content was independent of the reaction time. The methodology represents an alternative route to obtain silica with an unsaturated organic group, able to polymerize and stabilize up to 300–400°C. The modified material has a potential application as compatibilizing filler in dental composite.     

三甲基氯硅烷对纳米多孔二氧化硅薄膜的修饰

以正硅酸乙酯为先驱体,采用溶胶-凝胶法,结合旋转涂胶、超临界干燥工艺在硅片上制备了纳米多孔SiO2薄膜.用三甲基氯硅烷(TMCS)对该SiO2薄膜进行了表面修饰,采用FTIR、TG-DTA、AFM和椭偏仪等方法研究了TMCS修饰前后薄膜的结构、形貌、厚度与介电常数等性能.超临界干燥后的SiO2薄膜含有Si－O－Si与Si－OR结构,呈疏水性.在空气中250 ℃以上热处理后SiO2薄膜因含有Si－OH而呈吸水性. TMCS修饰后的SiO2薄膜在温度不高于450 ℃时可保持其疏水性和多孔结构. SiO2薄膜经TMCS修饰后基本粒子和孔隙尺寸增大,孔隙率提高,介电常数可降低至2.5以下.     

Synthesis of Silica Aerogels: Influence of the Supercritical CO2 on the Sol-Gel Process

The synthesis of silica aerogels was modified by addition of supercritical CO₂ during the sol-gel process. It was shown, that CO₂ acts as a catalyst and accelerates the gelation significantly. This effect was studied under a multitude of experimental conditions. The influence of the precursor concentration, temperature and the nature of the catalysts and solvent on the gel formation in presence of CO₂ was studied. Several gels obtained by this method were dried and transparent silica aerogels were produced.     

Fractal dimensions of silica gels generated using reactive molecular dynamics simulations

We have used molecular dynamics simulations based on a three-body potential with charge transfer to generate nanoporous silica aerogels. Care was taken to reproduce the sol-gel condensation reaction that forms the gel backbone as realistically as possible and to thereby produce credible gel structures. The self-similarity of aerogel structures was investigated by evaluating their fractal dimension from geometric correlations. For comparison, we have also generated porous silica glasses by rupturing dense silica and computed their fractal dimension. The fractal dimension of the porous silica structures was found to be process dependent. Finally, we have determined that the effect of supercritical drying on the fractal nature of condensed silica gels is not appreciable.     

Transport of liquids using superhydrophobic aerogels

The experimental results of the studies on the transportation of water droplets on a superhydrophobic silica aerogel-powder-coated surface are reported. The superhydrophobic silica aerogels were prepared using sol-gel processing of methyltrimethoxysilane (MTMS) precursor, methanol (MeOH) solvent, and base (NH4OH)-catalyzed water followed by supercritical drying using methanol solvent. The molar ratio of NH4OH/MTMS, H2O/MTMS, and MeOH/MTMS were varied from 1.7x10(-1) to 3.5x10(-1), 2 to 8, and 1.7 to 14, respectively, to find out the best-quality aerogels in terms of higher hydrophobicity and high droplet velocity. A specially built device was used for the measurement of velocity of water droplet of size 2.8 mm (+/-0.2 mm) on an inclined surface coated with superhydrophobic aerogel powder. Liquid marbles were prepared by rolling water droplets on aerogel powder and the marble(s) velocities on a noncoated inclined surface were compared with that of the water droplets. It was observed that the microstructure of the aerogel affects the droplet as well as marble velocities considerably. For an aerogel with uniform and smaller particles, the water droplet and marble velocities were observed to be maximum, i.e., 144 and 123 cm/s, respectively, whereas for the aerogels with bigger and nonuniform particles, the water droplet and marble velocities were observed to be minimum, i.e., 92 and 82 cm/s, respectively. The results have been discussed by taking into account the contact angles and microstructural observations.     

A two-step supercritical fluid extraction of polycyclic aromatic hydrocarbons from roadside soil samples

A two-step procedure for the supercritical fluid extraction (SFE) of polycyclic aromatic hydrocarbons from soil samples was developed. The procedure consists of a static supercritical fluid treatment in a closed extraction cell at a high temperature (T=250 or 340degreesC for 20 min) and an SFE with a solvent trapping. During the static phase, the sample is exposed to a supercritical organic solvent (methanol, toluene, dichloromethane, ACN, acetone, and hexane). The solvent penetrates particles of the matrix to substitute strongly bonded molecules and dissolves the analytes in the supercritical phase. At ambient temperature, supercritical fluids became liquid and lost their solvation abilities. Most of the analytes condense on the surface of the particles or on the extraction cell walls without forming strong bonds or penetrating deep into the matrix. Thus, the pretreatment liberates the analytes and they behave similar to those in freshly spiked samples. The common SFE with toluene-modified CO2 as an extraction fluid follows the static phase. With the use of the most suitable extraction phases (toluene, ACN), the extraction efficiency of the combined procedure is much higher (approximately100%). The results of the combined procedure are compared to the SFE procedure of the same untreated sample (difference less than 5%) and to the Soxhlet extraction. The extracts were analyzed using a GC with the flame ionization detection.     

聚乙二醇双丙烯酸酯在超临界二氧化碳中的光聚合研究

探索了聚乙二醇双丙烯酸酯在超临界二氧化碳中发生光聚合反应制备聚合物颗粒的过程.方法为向充满超临界二氧化碳的高压反应釜中,同时喷射二氧化碳与聚乙二醇双丙烯酸酯及光引发剂的溶液,溶液与二氧化碳形成均匀的喷雾并进一步通过反溶剂作用与超临界二氧化碳形成分散体系,当同步进行紫外光照射时,单体可以在超临界二氧化碳中发生光聚合.结果证明此方法是可行的,得到了聚合物微颗粒.研究了不同溶剂及反应原料用量对产物粒径分布的影响.采用不同溶剂,将改变反应原料及产物在超临界二氧化碳中的溶解度,进而改变产物的粒径分布;反应原料用量增加,其在超临界二氧化碳中的溶解度减小,导致产物粒径分布较宽。     

Synthesis of Submicron-Sized Titania-Coated Silica Particles with a Sol-Gel Method and Their Application to Colloidal Photonic Crystals

A previously proposed method for preparing monodispersed titania particles was extended to preparation of titania-coated silica spherical particles. The core silica particles with an average size of 264 nm were prepared with Stöber method. The titania-coating was performed in ethanol/acetonitrile solvent in the presence of silica particles by a sol-gel method with the use of titanium tetraisopropoxide (TTIP) and methylamine (MA) catalyst. Average size of the silica-titania particles decreased from 457 to 292 nm with an increase in concentration of silica particles. Coefficient of variation for the particle size was less than 5%. Colloidal crystals could be fabricated with a dip-coating technique and a sedimentation process, respectively. Measurements of reflectance revealed peaks based on the Bragg diffraction. Those peaks red-shifted with an increase in titania shell thickness because of a high refractive index of titania. Annealing at high temperature transformed crystal structure of titania shell from amorphous to anatase (500°C) and rutile (1000°C), which led to red-shift of reflection peak because of an increase in refractive index of titania due to the crystallization.     

Preparation of a mercaptopropyl bonded silica intermediate in supercritical carbon dioxide: synthesis, characterisation and chromatography of a quinine based chiral stationary phase

This research examines the preparation of a mercaptopropyl bonded silica intermediate in supercritical carbon dioxide (sc-CO(2)) and the subsequent conversion in sc-CO(2) to a quinine derived chiral stationary phase (CSP). The effects of reaction temperature, pressure and time on the surface coverage of the silica intermediate were investigated when porous silica particles (Exsil-Avanti, 3microm) were reacted with 3-trimethoxymercaptopropylsilane in sc-CO(2). We present results which demonstrate that a stable mercaptopropyl bonded silica intermediate can be successfully prepared under supercritical conditions of 40 degrees C, 483bar, in a substantially reduced reaction time of 1h with superior surface coverages compared to organic solvent based methods. The further utility of this supercritical fluid technology was demonstrated by the free radical addition of a quinine derived chiral selector onto a mercaptopropyl bonded silica intermediate in sc-CO(2). This supercritical fluid generated chiral stationary phase (CSP) was utilised for the direct LC enantioseparation of a series of 3,5-dinitrobenzoyl (DNB) amino acids. Bonded silica samples were characterised using elemental analysis, diffuse reflectance infrared fourier transform (DRIFT) spectroscopy, solid state (13)C and (29)Si CP-MAS NMR spectroscopy, and thermogravimetric analysis (TGA). This supercritical fluid functionalisation approach offers an efficient and cleaner alternative to existing organic solvent based approaches for the preparation of bonded silica phases.     

Hybrid Silica Gel-Polytetrahydrofuran Thin Films

The sol-gel process has been used to prepare hybrid silica gel-polytetrahydrofuran (PTHF) thin films, using tetraethylorthosilicate (TEOS) as the precursor. The films were prepared by spin-coating, and characterized by profilometry, transmission FTIR and SEM. Film properties were conditioned by the preparation procedure as well as by the initial recipe, namely the solvent, polymer content and molecular weight. Evidence was obtained of the participation of the polymer in the condensation step of the process, interacting by hydrogen bonds with hydroxyl groups of the silicate network.     

Direct synthesis of zirconia aerogel nanoarchitecture in supercritical CO2

The objective of the present study was to synthesize porous ZrO2 aerogels with a nanostructure via a direct sol-gel route in the green solvent supercritical carbon dioxide (scCO2). The synthesis involved the coordination and polycondensation of a zirconium alkoxide using acetic acid in CO2, followed by scCO2 drying and calcination. Either a translucent or opaque monolith was obtained, which was subsequently characterized by electron microscopy, X-ray diffraction, thermal analysis, N2 physisorption, and infrared spectroscopy analysis. The electron microscopy results showed that the translucent monolithic ZrO2 exhibited a well-defined mesoporous structure, while the opaque monolith, formed using added alcohol as a cosolvent, was composed of loosely compacted nanospherical particles with a diameter of ca. 20 nm. After calcination at 400 and 500 degrees C, X-ray diffraction results indicated that the ZrO2 exhibited tetragonal and/or monoclinic phases. In situ infrared spectroscopy results showed the formation of a Zr-acetate coordinate complex at the initial stage of the polycondensation, followed by further condensation of the complex into macromolecules.     

Physical Properties of Silica Aerogels Prepared with Polyethoxydisiloxanes

Silica aerogels were made by sol-gel techniques using industrial silicon derivatives (polyethoxydisiloxanes, E-40), followed by supercritical drying with ethanol. The morphology and microstructure of the silica aerogels were investigated by using specific surface area, S_BET, SEM, TEM and the pore size distribution techniques. The thermal conductivity was also measured as a function of air pressure. The results show that the diameter of the silica particles is about 13 nm and the pore size of the silica aerogels is 20–80 nm. The specific surface area of the silica aerogel is about 470 m²/g and the thermal conductivity of the silica aerogel prepared with E-40 is 0.014 w m^–1 K^–1 at room temperature and 1 atm.     

氧化硅组装纳米Nafion酸催化合成α-生育酚

以自制的Nafion溶液、正硅酸乙酯为原料，通过溶胶-凝胶方法，将Nafion纳 米颗粒分散组装到多孔性SiO_2中，制得高比表面积纳米复合物Nafion/SiO_2固体 酸催化剂大大提高了Nafion所含酸性中心的暴露率和可接近程度。在非极性溶剂正 庚烷和甲苯中，13% Nafion/SiO_2固体酸对α-生育酚的合成具有很好的选择催化 作用。相对于致密性Nafion树脂而言，13% Nafion/SiO_2纳米复合物单位酸中惊扰 催化活性增加了10倍。     

Silica reinforcement of epoxidized natural rubber by the sol-gel method

The sol-gel technique was employed to prepare silica-reinforced vulcanizates using tetraethylorthosilicate (TEOS) and epoxidized natural rubber (ENR). The rubber was first precured with 3-aminopropyltriethoxysilane (APS) by heat pressing at 180°C for a range of cure time. The resultant rubber sheets or vulcanizates were swelled in TEOS, and subsequently subjected to a sol-gel reaction in butylamine aqueous solution. Hydrolysis and condensation of the TEOS resulted in the formation of silica particles in the rubber network yielding silica-contained vulcanizates. Silica content as high as 28% and TEOS-to-silica conversion of over 60% were observed. When prepared under certain reaction conditions, the sol-gel vulcanizates obtained were more rigid and stronger than a typical sulfur-cured ENR vulcanizate that contained comparable amount of silica. Comparative stress-strain and dynamic mechanical property analysis suggest that chemicals bond are formed between the silica particles and the rubber network in the ENR-APS-sol-gel vulcanizate. Thus, the in situ silica reinforcement of ENR was successfully established.On leave from School of Industrial Technology, University Sains Malaysia, Minden, 11800, Penang, Malaysia.