锐钛矿相纳米TiO2晶体生长动力学及生长过程控制

研究了采用溶胶-凝胶法经由前驱物钛酸四异丙酯水解制备纳米TiO₂结构相变及锐钛矿晶体生长动力学过程. 研究结果表明,在酸性条件下水解,由于高压热处理温度的变化导致锐钛矿向金红石相的结构相变,锐钛矿相纳米TiO₂生长活化能在250℃以下和以上分别为(15.8±4.5)kJ/mol和(80.2±1.0)kJ/mol;而在碱性条件下水解的活化能值为(3.5±0.4)kJ/mol. 在不发生结构相变的条件下,酸性水解条件下锐钛矿相纳米TiO₂生长速 关键词： 2')" href="#">纳米TiO₂ 锐钛矿 生长动力学 溶胶-凝胶法     

锐钛矿相纳米TiO2晶体生长动力学及生长过程控制

研究了采用溶胶-凝胶法经由前驱物钛酸四异丙酯水解制备纳米TiO2结构相变及锐钛矿晶体生长动力学过程. 研究结果表明,在酸性条件下水解,由于高压热处理温度的变化导致锐钛矿向金红石相的结构相变,锐钛矿相纳米TiO2生长活化能在250℃以下和以上分别为(15.8±4.5) kJ/mol和(80.2±1.0) kJ/mol;而在碱性条件下水解的活化能值为(3.5±0.4 kJ/mol. 在不发生结构相变的条件下,酸性水解条件下锐钛矿相纳米TiO2生长速率相比没有碱性条件下快,即表明在酸性条件下提高锐钛矿生长速率主要依靠提高温度来实现,而在碱性条件下,可以通过延长高压热处理时间使得晶体生长速率加快,该研究成果对实现锐钛矿相纳米TiO2晶体尺寸控制和将来批量化制备提供了理论和实验指导.     

用SAXS和XRD方法研究TiO2纳米颗粒微观结构

用溶胶-凝胶方法制备了TiO₂纳米样品,并对该样品在300℃到800℃温度区域进行了退火处理.应用同步辐射X射线粉末衍射(XRD)方法研究了经不同热处理温度的TiO₂纳米颗粒的结构相变.应用同步辐射小角X射线散射(SAXS)方法研究了TiO₂纳米颗粒的表面分形与界面特性.得到纳米颗粒粒度与退火温度的变化规律,讨论了表面界面特征与相变的关系. 关键词： X射线小角散射 X射线衍射 2纳米颗粒')" href="#">TiO₂纳米颗粒     

水热法合成FeS2粉晶及其生长热动力学的研究

采用溶胶_凝胶水热法合成了单相黄铁矿结构的FeS2₂粉晶. 用x射线衍射、傅 氏变换红外光谱等分析手段对FeS2₂粉晶进行了表征，以简化的数学模型及相 变理论讨论了晶体 生长过程. 结果表明：FeS2₂晶粒的生长过程属于相变与扩散的混合机制，符 合经时间 指数修正的二次方动力学方程，是一个生长速率随时间变化的过程；水热晶化温度高于453 K、反应时间超过18 h且有适量的硫参与反应时，可得到单相的黄铁矿型的FeS2₂关键词： 溶胶_凝胶水热法 2粉晶')" href="#">FeS2₂粉晶 晶粒生长 热动力学     

电场热处理条件下TiO2薄膜的晶化行为研究

利用溶胶-凝胶法和电场热处理工艺在玻璃表面制备出一层TiO₂薄膜，采用DTA ，Raman光 谱，XRD和AFM等测试手段分析了TiO₂薄膜在电场热处理过程中的晶化行为.然后 在理论上 分析了外电场对TiO₂薄膜热处理过程的影响，提出了通过引入外电场促进TiO2薄膜从无 定形到锐钛矿的相转变的方法.通过甲基橙水溶液的光催化降解实验表明：在520℃电场热处 理条件下的TiO₂薄膜的光催化效率高于未引入电场热处理的TiO₂薄 膜. 关键词： 薄膜 晶化 电场 2')" href="#">TiO₂     

Grain Growth Kinetics of BaTiO3 Nanocrystals During Calcining Process

以醋酸钡和钛酸四丁酯为原料,采用溶胶-凝胶法合成了纳米BaTiO3粉体;运用差示/热重、X射线衍射及透射电镜对前驱体凝胶和产物进行了表征,并根据XRD结果,研究了纳米BaTiO3的晶格常数、晶格畸变度和晶粒尺寸随焙烧温度及时间的变化。结果表明,焙烧温度与时间对纳米BaTiO3晶格常数的影响不明显;随焙烧温度或时间的延长,纳米BaTiO3的晶格畸变度减小,晶粒尺寸增大,但晶格畸变度和晶粒尺寸更敏感于焙烧温度. 基于扩散控制机理的传统模型探讨了焙烧过程纳米BaTiO3晶粒生长动力学,得出其晶粒生长指数为7,晶粒生长活化能为75.49 kJ/mol. 将基于扩散与反应共同控制机理的新型等温模型应用于本研究中,结果表明,新型等温模型更能真实地反映纳米BaTiO3焙烧过程中的晶粒生长行为,说明纳米BaTiO3晶粒生长过程同时受溶质扩散和表面反应控制,其藕合晶粒生长活化能为27.23 kJ/mol.     

稀土钇、镧掺杂TiO2薄膜的拉曼谱分析

采用溶胶-凝胶法在石英玻璃衬底上用旋涂法制备了未掺杂、掺杂钇和掺杂镧的TiO₂薄膜样品,对样品在700—1100 ℃范围内进行退火处理,并对样品的拉曼光谱进行了分析.分析表明:随着退火温度的升高,未掺杂TiO₂薄膜发生了从锐钛矿相经混相最终向金红石相的转换,掺杂钇和掺杂镧对TiO₂薄膜的晶相转换起阻碍作用,掺杂镧的阻碍作用更强;稀土掺杂能使TiO₂薄膜晶粒细化,并使晶粒内部应力增大从而阻碍晶格振动,掺杂镧比掺杂钇的效果 关键词： 2薄膜')" href="#">TiO₂薄膜 稀土掺杂 拉曼光谱 溶胶-凝胶     

金红石→萤石TiO2相变的第一性原理计算

利用第一性原理平面波密度泛函理论并结合准谐德拜模型,对TiO₂从金红石结构到萤石结构的相变进行理论研究.依据焓相等原理,得到TiO₂从金红石结构到萤石结构的相变压强为45.32 GPa,并通过吉布斯能的计算发现相变压强随温度的增加而增加,运用拟合的方法估计实验条件下的相变压强(温度为1900-2100K时,P_t=47.604~47.756 GPa).运用等吉布斯能原理,得到零压下从金红石到萤石结构TiO₂的相变温度为2029 K.计算结果与实验及其他理论值相符,并通过准谐德拜模型成功获得相变前后的结构和热力学性质,如相对体积、热膨胀系数、热容和德拜温度等.     

二氧化钛微晶结构相变与光致发光

以钛酸四丁脂为前驱体制备了二氧化钛(TiO₂)胶体,将其粉末在不同温度下作热处理,采用差热分析、X射线衍射、荧光光谱等手段对样品进行测试。结果表明,随着热处理温度升高,TiO₂由板钛矿相经锐钛矿相向金红石相转变,在808℃左右出现一级相变。原始粉末样品以及在600℃以下热处理的样品,在400nm处可观察到TiO₂纳米晶的带边发光,在470nm处可观察到表面态发光;当热处理温度达到850℃时,主晶相转变为金红石相,400nm处的带边发光峰消失,位于470nm处发光峰成为最强峰,但强度减弱,并且样品发光的波长范围明显变窄。其原因是,随着热处理温度升高,晶粒不断长大,量子限域效应减弱乃至消失,晶粒的表面状况发生变化,导致样品的荧光发射行为发生变化。     

CoFe2O4纳米颗粒的结构、磁性以及离子迁移

聚乙烯醇(PVA)溶胶凝胶法制备出CoFe₂O₄纳米微粉，用X射线衍射研究了铁氧体纳米颗粒的结构.测量了CoFe₂O₄纳米颗粒80—873 K的变温穆斯堡尔谱，发现纳米颗粒的磁转变温度范围为793—813 K，比块体材料的磁性转变温度要低.CoFe₂O₄纳米颗粒的德拜温度θ_A=674 K，θ_B=243 K，比块体材料要小.CoFe₂O₄纳米颗粒超精细场H_f随温度的变化符合T^3/2+T^5/2定理.当温度较高时，平均同质异能移IS随温度的升高而减小，并呈线性关系. 关键词： 纳米颗粒 磁性 穆斯堡尔谱     

The Effect of Hydrolysis Temperature on Synthesis of Bimodally Nanostructured Porous Titania

Bimodally porous (2–4 and 20–100 nm) titania powders were prepared by hydrolysis of titanium tetraisopropoxide (TTIP), and the effect of hydrolysis temperature on the phase transformation and pore structure was investigated. The phase transformation was slightly retarded with increasing hydrolysis temperature, when the initial water concentration was small. The evolution of particle phase composition from amorphous to crystalline anatase and rutile was largely proportional to the calcination temperature and the initial water concentration. The pore size distribution was bimodal with fine intra-particle pores (2–4 nm in diameter) and larger inter-particle pores (20–100 nm). The intra-particle pores decreased in diameter at the hydrolysis temperature of 20°C. The specific surface area (SSA) of the dried powders ranged from 253 to 587 m²/g and the highest SSA was obtained at the hydrolysis temperature of 20°C.     

Synthesis of photocatalytic active fibrous titania by the solvothermal reactions

Abstract

Fibrous titania was synthesized by the solvothermal reactions of H₁Ti₄O₉ nH₂in different media. H₂Ti₄O₉·nH₂O transformed in steps to H₂Ti₈O₁₇, monoclinic TiO_z, anatase and rutile. The phase transformation temperature and microstructure of the products changed significantly depending on the heating environment. The critical temperature at which anatase appeared in liquid media was much lower than that in air. The titania fibers consisted of nanocrystals of TiO₂. The crystallite size and crystallinity of titania decreased with decreasing the dielectric constant of the reaction medium. Consequently, the photocatalytic activity of titania changed with heat treatment media in the following sequence: ethanol, methanol > water > air, i.e., fibrous titania possessing excellent photocatalytic activity could be obtained by the solvothermal reactions using alcohol such as methanol and ethanol. Titania powders crystallized by the solvothermal reaction in methanol also possessed excellent thermal stability.     

Effect of calcination temperature on porous titania prepared from industrial titanyl sulfate solution

Porous titania with anatase phase was prepared via thermal hydrolysis of industrial titanyl sulfate solution, and subsequent calcination at different temperature. The as-prepared powders were characterized by TG, DSC, XRD, particle size distribution test, N₂ adsorption-desorption isotherm and SEM. Raising calcination temperature could accelerate the crystal growth, enlarge its specific surface area, pore diameter, and improve its photocatalytic activity. While too high temperature could destroy the pore structure even collapse. The optimal calcination temperature is 550 °C, and the obtained sample showed good thermal stability and high photocatalytic activity, with specific surface area of 189.3 m²/g and higher degree of crystallinity, and its photocatalytic degradation rate of methylene blue was of 95.76%.     

High temperature stability of nanocrystalline anatase powders prepared by chemical vapour synthesis under varying process parameters

Systematic variation in the high temperature stability of nanocrystalline anatase powders prepared by chemical vapour synthesis (CVS) using titanium (IV) isopropoxide under varying flow rates of oxygen and helium was obtained by progressively shifting the decomposition product from C₃H₆ to CO₂. The as-synthesised powders were characterised by high temperature X-ray diffraction (HTXRD), simultaneous thermo-gravimetric analyses (STA), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) and transmission electron microscopy (TEM). It was observed that the anatase to rutile transformation temperature progressively increased for samples synthesised at higher O₂/He flow rate ratios. The improved anatase stability was attributed to the presence of incorporated carbon within the titania structure and confirmed by a high temperature carbon desorption peak.     

Titanium Dioxide Nanoparticles Produced in Water-in-oil Emulsion

Titanium dioxide (titania) particles were prepared by a water-in-oil emulsion system, and studied for the photodecomposition property of methylene blue. Microemulsion (ME) consisted of water, cyclohexane or octane, and surfactant, such as polyoxyethylene (10) octylphenyl ether (TX-100), polyoxyethylene lauryl ether, or bis (2-ethylhexyl) sodium sulfosuccinate. Titanium tetraisopropoxide (TTIP) was dropped into the ME solution and then titania particles were formed by the hydrolysis reaction between TTIP in the organic solvent and the water in the core of ME. It was found that ME could be classified to the reversed micelle (RM) region and the swelling reversed micelle (SM) region according to the water content. The water droplets in RM were almost monodispersed, where the water content was small. On the other hand, the water droplets in SM had a size distribution, although most of the water molecules associated with surfactant molecules. The size of the particles prepared in the RM region was smaller than the ME size. In contrast, the size of the particles formed in the SM region was larger than the ME size, and coagulation of the particles was observed within a few hours. The smallest diameter of the particles was 2 nm in the system of cyclohexane with TX-100 surfactant when the molar ratio of water to surfactant was 2. Titania particles prepared in this condition were collected as amorphous powder, and converted to anatase phase at less than 500 K, which is lower than the ordinal phase transition temperature. These anatase phase titania particles only showed a significant photodecomposition of methylene blue by illumination with a Xenon lamp.     

Thermostable photocatalytically active TiO<Subscript>2</Subscript> anatase nanoparticles

Anatase is the low-temperature (300–550 °C) crystalline polymorph of TiO₂ and it transforms to rutile upon heating. For applications utilizing the photocatalytic properties of nanoscale anatase at elevated temperatures (over 600 °C) the issue of phase stabilisation is of major interest. In this study, binary TiO₂/SiO₂ particles were synthesized by a flame aerosol process with TiCl₄ and SiCl₄ as precursors. The theoretical Si/Ti ratio was varied in the range of 0.7–1.3 mol/mol. The synthesized TiO₂/SiO₂ samples were heat treated at 900 and 1,000 °C for 3 h to determine the thermostability of anatase. Pyrogenic TiO₂ P25 (from Evonik/Degussa, Germany) widely applied as photocatalyst was used as non-thermostabilized reference material for comparison of photocatalytic activity of powders. Both the non-calcinated and calcinated powders were characterized by means of XRD, TEM and BET. Photocatalytic activity was examined with dichloroacetic acid (DCA) chosen as a model compound. It was found that SiO₂ stabilized the material retarding the collapse of catalyst surface area during calcination. The weighted anatase content of 85% remains completely unchanged even after calcination at 1,000 °C. The presence of SiO₂ layer/bridge as spacer between TiO₂ particles freezes the grain growth: the average crystallite size increased negligibly from 17 to 18 nm even during the calcination at 1,000 °C. Due to the stabilizing effect of SiO₂ the titania nanoparticles calcinated at 900 and 1,000 °C show significant photocatalytic activity. Furthermore, the increase in photocatalytic activity with calcination temperature indicates that the titania surface becomes more accessible either due to intensified cracking of the SiO₂ layer or due to enhanced transport of SiO₂ into the necks thus releasing additional titania surface.     

An investigation of phase transformation of titania slag using microwave heating

The influences of microwave heating on the phase transformation of titania slag were systematically investigated. The thermal stability, surface chemical functional groups and microstructure of the titania slag before and after microwave heating, at a temperature of 950?°C for 60 min, were also analyzed using thermogravimetry and differential thermal analysis (TG-DSC), Fourier transform infrared spectroscopy (FT-IR) spectrum and scanning electron microscope (SEM), respectively. The TG-DSC analysis revealed that the phase transformation of the titania slag from anatase TiO₂ to rutile TiO₂ occurred between 750 and 1000 °C. The FT-IR rustles demonstrate that the banding form of Ti⁴⁺, Ti³⁺ and Ti²⁺ ions and the methyl groups on the surface of the titania slag has changed and a new chemical bond Ti–OH was formed. The results of SEM showed that a large number of regulation rutile TiO₂ crystals were found on the surface of the microwave-treated samples and the synthetic rutile has been synthesized successfully using microwave heating.     

TiO_2晶型及其相变的高温拉曼光谱研究

本文测量了锐钛矿型和金红石型TiO2常温至1923K的高温拉曼光谱,观察了锐钛矿型TiO2在1373K～1473K间发生相变,不可逆转化为金红石型TiO2,分析了特征峰随温度变化的规律以及两种结构相的温度依赖性。并为不同晶型TiO2的研究、生产和应用提供重要的实验依据。     

Preparation of F-doped titania nanoparticles with a highly thermally stable anatase phase by alcoholysis of TiCl4

Pure anatase is a metastable phase and inclined to (transform) be transformed into rutile structure under heating over than 500 °C, which limits its suitability for high-temperature applications. Hitherto much research efforts have been made to increase the stability temperature of anatase structure. However, metallic doping usually introduced metallic oxides into titania at high temperature, and many nonmetallic doping are not competent for increasing the stability temperature of anatase structure up to 900 °C. In this study, F-doped anatase TiO₂ nanoparticles were conveniently prepared via the alcoholysis of TiCl₄ and the as-prepared product shows very high stability temperature up to 1000 °C before being transformed into rutile structure phase. On the basis of XPS results of F-doped titania annealed at different temperature, it is learned that the F atoms were anchored on the crystal planes of anatase in favor of decreasing the energy faces of anatase and stabilizing the anatase structure till annealed at 1300 °C all the anatase were transformed into rutile phase.