聚乙二醇、聚丙二醇和环氧乙烷-环氧丙烷嵌段共聚物在固-液界面上的吸附 III:硅烷化活性炭/水和甲基化硅胶/水界面

测定了25℃时硅烷化不同时间(1至30天)的活性炭及甲基化硅胶自水溶液中吸附四种聚乙二醇(PEG)、三种聚丙二醇(PPG)和环氧乙烷(EO)-环氧丙烷(PO)嵌段共聚物pluronic-L64的等温线。结果表明, 在各活性炭样品上的等温线均为Langmuir型的; 同一炭样对不同PEG的极限吸附量(g·g^-^1)与分子量无关; 极限吸附时每个PEG分子所占面积(A)与分子中所含EO数(nEO)间有直线关系, 直线的斜率与硅烷化时间有关, 这一结果可用硅烷化时间延长时吸附分子的EO基可能以其氧原子向水, 碳氢链节靠近固体表面取向的模型解释。根据PPG的极限吸附量与分子量有关和极限吸附时的分子面积推断PPG分子不是以平躺方式吸附。甲基化硅胶对PEG的吸附量极小, 对PPG的吸附量随分子量减小急剧降低, 而对L64的吸附量明显大于在亲水硅胶上的。文中对所得结果给出了初步的解释。     

Properties of gold electrode modified with dimercaptosuccinic acid and electrochemical behavior of copper histidine complex

A self-assembled monolayer of meso-2,3-dimercaptosuccinic acid was prepared on the surface of gold disc electrode. The modified electrode was characterized using cyclic voltammetry in copper(II) solution and cyclic voltammetry and electrochemical impedance spectroscopy in the presence of potassium hexacyanoferrate( II)/(III) and hexaammineruthenium (II)/(III) chloride. Binding of copper(II) histidine complex (Cu–His) onto the electrode was successfully achieved for a wide range of tested concentrations, as shown with adsorption transfer stripping voltammetry. Electrode response (logΔI_p) was linearly proportional to logc(Cu–His) with correlation coefficient R³² = 0.9839.     

Amperometric hydrogen peroxide biosensor based on a glassy carbon electrode modified with polythionine and gold nanoparticles

We report on a novel hydrogen peroxide biosensor that was fabricated by the layer-by-layer deposition method. Thionine was first deposited on a glassy carbon electrode by two-step electropolymerization to form a positively charged surface. The negatively charged gold nanoparticles and positively charged horseradish peroxidase were then immobilized onto the electrode via electrostatic adsorption. The sequential deposition process was characterized using electrochemical impedance spectroscopy by monitoring the impedance change of the electrode surface during the construction process. The electrochemical behaviour of the modified electrode and its response to hydrogen peroxide were studied by cyclic voltammetry. The effects of the experimental variables on the amperometric determination of H₂O₂ such as solution pH and applied potential were investigated for optimum analytical performance. Under the optimized conditions, the biosensor exhibited linear response to H₂O₂ in the concentration ranges from 0.20 to 1.6?mM and 1.6 to 4.0?mM, with a detection limit of 0.067?mM (at an S/N of 3). In addition, the stability and reproducibility of this biosensor was also evaluated and gave satisfactory results.

A novel label-free electrochemical aptasensor for thrombin based on the {nano-Au/thionine}n multilayer films as redox probes

Herein, a novel label-free electrochemical aptasensor based on direct immobilization of the redox probes on an electrode surface was reported. Gold electrode coated Nafion was firstly modified with redox probe-thionine (Thi) through ion exchange adsorption. Then, with the help of chemisorption and electrostatic adsorption, negatively charged nano-Au and positively charged Thi were layer-by-layer (LBL) self-assembled onto the modified electrode surface, which formed {nano-Au/Thi⁺}_n multilayer films for improving the amount of redox probes and immobilizing thiolated thrombin aptamers (TBA). In the presence of target thrombin (TB), the TBA on the multilayer film could catch the TB onto the electrode surface, which resulted in a barrier for electro-transfer, leading to decrease of the current. The proposed method avoided the cubsome redox probe labeling process, increased the amount of redox probe and reduced the distance between the redox probe and electrode surface. Thus, the approach showed a high sensitivity and a wider linearity to TB in the range from 0.12 nM to 46 nM with a detection limit of 40 pM.     

Cathodic stripping determination of iron at a platinum electrode modified by adsorption of adenosine-5'-monophosphate

Irreversible adsorption of adenosine-5'-monophosphate onto platinum yields an electrode surface which is readily plated by formation of a non-labile complex with iron(III) present initially in solution or formed by oxidation of iron(II). A negative potential scan subsequent to a 60-s deposition step produces a cathodic stripping peak, the height of which is proportional to the sum of the Pe(III) and Fe(II) concentrations in solution. Oxalate can be used to mask the response to Fe(III). The method is shown to be applicable to determinations of Fe(III) and Fe(II) in the concentration range lO^-8–lO^-6 mol l^-1.     

Adsorption behavior of acidic and basic proteins onto citrate-coated Au surfaces correlated to their native fold, stability, and pI

The adsorption of eight different proteins (alpha-lactalbumin (types I and III), bovine serum albumin, hemoglobin, myoglobin, cytochrome c, alpha-casein, and lysozyme) onto a model anionic surface was performed at equivalent bulk (solvent, ionic strength, pH) and surface conditions. Adsorption was monitored on a quartz crystal microbalance with dissipation monitoring (QCM-D) with citrate-coated gold surfaces as adsorbents and has been correlated to native fold stability determined from near- and far-UV circular dichroism (CD) measurements. The proteins studied here were chosen based on their pI and documented knowledge about their structural stability and flexibility. Protein adsorption was found to be independent of global protein charge. Rather, binding occurs through oppositely charged patches on protein and surface. Moreover, data indicate that there is a correlation between secondary and tertiary structure stability and the adsorption characteristics at interfaces. Also, protein surface coverage, layer thickness, and flexibility can be tuned as a function of deposition method. This is discussed in terms of adsorption/spreading kinetics and intermolecular (protein-surface and protein-protein) interactions. Adsorption to surfaces can induce formation of supramolecular structures such as micelles (in the case of alpha-Cas) and multilayers (as for Hb). In the case of alpha-casein, this phenomenon depends on the deposition method and protein concentration. When ranking the surface coverage for proteins added in excess, the order is Lyz < Cyt c < Mb < BSA < alpha-La I < alpha-Cas < alpha-La III < Hb, which can be correlated to the proteins ability to form supramolecular structures (alpha-Cas, Hb), overall conformational flexibilities, and ability to form stable intermediates.     

Adsorption of insoluble surfactants at the Au(111)/solution interface

The adsorption of surfactants, which form insoluble monolayers on an aqueous substrate, onto a single crystal gold electrode have been described. Adsorption of this class of surfactants have been characterized using a combination of electrochemistry and Langmuir-Blodgett techniques. We have developed a technique to simultaneously measure the film pressure at the gas-solution (GS) interface and the film pressure of the surfactants that spread to the metal-solution (MS) interface. We have shown that surfactants such as octadecanol and stearic acid, which interact weakly with the metal surface, adsorb at an uncharged MS interface (at the potential of zero charge) and progressively desorb when the electrode surface is charged negatively. The electrode potential (charge density at the metal surface) influences the transfer of the surfactant from the GS interface to the MS interface. The transfer ratio is 1:1 at an uncharged MS interface, and is progressively reduced to zero when the MS interface is charged. We have employed 12-(9-anthroloxy) stearic acid, a surfactant dye molecule, to study the mechanism of potential induced desorption and adsorption of the film of insoluble molecules. With the help of electroreflectance spectroscopy and light scattering measurements, we have shown that if desorbed, the surfactant molecules form micelles (flakes or vesicles) that are trapped under the electrode surface. The micelles spontaneously spread back onto the electrode surface when the charge density at the metal approaches zero. The repeatable desorption and readsorption involve micellisation of the film at negative potentials and spontaneous spreading of the micelles to reform the monolayer at potentials close to pzc.     

A novel strategy for immobilization of thionine based on calcium carbonate-gold nanoparticles inorganic hybrid composite and its application in hydrogen peroxide sensor

A novel strategy for efficient immobilization of electroactive Thionine(Th)on the gold(Au)electrode surface based on calcium carbonate-gold nanoparticles(CaCO3-AuNPs)inorganic hybrid composite was proposed and conducted by the strong electrostatic interaction between positively charged Th and negatively charged CaCO3-AuNPs composite.The hybrid composite was obtained by the adsorption of AuNPs onto the surface of CaCO3 microspheres through electrostatic interaction.Due to the microporous architecture,large s...     

Voltammetry of copper species in estuarine waters induced adsorption of copper on the hanging mercury drop electrode in complexing ligand/surfactant/chloride media

The adsorption of copper species on a positively charged hanging mercury drop electrode in complexing ligand/surfactant/chloride solution is discussed. Techniques used were differential pulse voltammetry of the copper in the adsorbed film, and potential-step reduction of adsorbed copper followed by different pulse anodic stripping voltammetry of Cu(Hg). The CuCl^?₂ species is shown to be the most important copper moiety adsorbed on the electrode and the adsorption is enhanced by organic films. This can be a critical pathway in the reduction of copper(II) in estuarine waters. The induced adsorption of copper in organic layers has biogeochemical implications associated with the nature of organic films and their influence on the Cu(II)/Cu(I) redox couple. There are also analytical applications, e.g., the compositional assay of organic monolayers by utilising Cu(II) and Cu(I) adsorption as electoractive probes and the determination of solution copper-organic binding.     

The electrochemistry of chromium in molten LiCl+KCl

Chronopotentiometric and steady-state voltammetric techniques have been employed to study the electroreduction processes:Cr(III)+eCr(II) andCr(II)+2eCr(0) separately, using the LiCl+KCl eutectic as solvent at 500°C.The adsorption of the ions on the electrode surfaces appears to play a role in the overall electrode processes; the degree of adsorption was correlated with the variation of exchange current density with concentration in the case of the Cr(II) ions. Fluoride ions had no effect on the electrode processes. The chronopotentiometric behaviour of Cr(III) ions was rather complex but adsorption appeared to play a part in this case also.     

Adsorption and viscoelastic properties of cationic xylan on cellulose film using QCM-D

The adsorption and viscoelastic properties of cationic xylan layers adsorbed from an aqueous electrolyte solution (NaCl 0, 1, 10, 100 mM) on a cellulose model surface were studied using quartz crystal microbalance with dissipation (QCM-D). Three cationic xylans with different charge densities were used (molecular weight, 9,600 g/mol with degrees of substitution, DS = 0.150, 0.191, and 0.259). The influences of the electrolyte concentration and charge density of cationic xylan on its adsorption onto a cellulose surface were investigated. Low charged cationic xylan was substantially more efficient in surface adsorption on cellulose compared to high charged cationic xylan at a low concentration of electrolytes. Adsorption of low charged cationic xylan decreased with increases in electrolyte concentration. However, adsorption of high cationic xylan increased with electrolyte concentration. The conformation and viscoelastic properties of the layers were interpreted by modeling the data under the assumption that the layers can be explained by the a Voigt model. Low charged cationic xylan adsorbed relatively weakly onto the cellulose surface, and formed a thicker, softer layer than high charged cationic xylan. On the other hand, high charged cationic xylan formed a thinner adsorption layer onto the cellulose surface.     

Determination of nickel and cobalt in natural waters and biological material by reductive chronopotentiometric stripping analysis in a flow system without sample deoxygenation

The instrumental set-up consists of a thin-layer cell with a glassy carbon working electrode and an inlet valve by means of which six different solutions can be sucked through the cell. The system is controlled by a microprocessor and suction is provided by means of a peristaltic pump. In the first step of the analytical cycle, a mercury film is plated onto the glassy carbon electrode and then the sample solution is allowed into the cell and nickel(II) and cobalt(II) are potentiostatically adsorbed onto the mercury film as their dimethylglyoxime complexes. Nickel(II) and cobalt(II) are then reduced in a medium of 5 M calcium chloride by means of constant current and simultaneously the microprocessor records the potential vs. time behaviour of the working electrode. Finally the mercury film is removed by mild oxidation in an iodine/iodide solution and the glassy carbon surface is cleaned with ethanol and sodium hydroxide prior to the next analytical cycle. The cobalt(II) and nickel(II) concentrations are evaluated by means of a standard addition procedure. The technique was applied to drinking, estuarine and sea water samples. The detection limits on the one sigma level after one minute of potentiostatic adsorption were 9 and 11 ng l^?1 for nickel(II) and cobalt(II), respectively. Nickel(II) and cobalt(II) were determined in reference samples of bovine liver and sea-water sediments after acid digestion. In order to obtain correct cobalt values, it was necessary to reduce cobalt(III) species formed during the acid digestion with sodium tetrahydroborate.     

基于纳米金和硫堇固定酶的过氧化氢生物传感器

在铂电极上自组装一层纳米金(GNs), 构建负电荷的界面, 然后通过金-硫、金-氮共价键合作用和静电吸附作用自组装一层阳离子电子媒介体硫堇(Thio). 再以同样的作用自组装一层GNs和辣根过氧化酶(HRP)的混合物, 最后在电极最外层滴加一层疏水性聚合物壳聚糖(Chit), 由此制备了一种新型的过氧化氢生物传感器. 研究了工作电位、检测底液pH、温度对响应电流的影响, 以及GNs和HRP之间的相互作用, 探讨了传感器的表面形态、交流阻抗、重现性和稳定性. 该传感器的酶催化反应活化能为12.4 kJ/mol, 表观米氏常数为6.5×10^－4 mo/L, 在优化的实验条件下, 所研制的传感器对H₂O₂的线性范围为5.6×10^－5～2.6×10^－3 mol/L, 检出限为1.5×10^－5 mol/L. 应用此方法制备了HRP和葡萄糖氧化酶(GOD)双酶体系葡萄糖生物传感器, 并应用于实验样品葡萄糖含量的测定.     

Collapse of Four-Arm Stars Polyelectrolyte Brushes Under An Electric Field in the Presence of Trivalent Salt Coions

Langevin dynamics simulations were conducted to study the collapse of grafted partially charged 4-arm star chains onto the oppositely charged grafting electrode in the presence of trivalent salt coions. Simulation results reveal that the average charge fraction of the grafted star chains and the salt concentration play critical roles in the competitive adsorption of charged monomers and trivalent salt coions onto the oppositely charged electrode. For grafted star chains with relatively high charge fraction, charged monomers are the dominant species collapsing on the oppositely charged electrode with the emergence of charge reversal on the grafting electrode. At a low charge fraction such that the total amount of charges on a grafted star molecule is comparable to that of a trivalent salt coion, trivalent salt coions absorb more strongly onto the electrode than grafted stars even at very low salt concentration. It is found that at relatively low charge fraction of star chains, the addition of trivalent salt coions does not lead to charge overcompensation of the surface charges on the grafting electrode. The stretching of star brushes under an electric field in the presence of trivalent salt coions was also briefly investigated.     

Inhibition of oxygen reduction on iron phthalocyanine layers by glutathione in buffered neutral media: Investigation by potentiometry,cyclic voltammetry and operational impedance techniques

The inhibition of oxygen reduction on iron—phthalocyanine layers, vacuum sublimed onto a gold surface, has been investigated as a function of various glutathione concentrations. Transient measurements, performed using the operational impedance technique, have shown that specific adsorption of glutathione occurs on the Fe(III) sites. The interpretation of the data by a model of charge carrier injection emphasizes the role of regulation of the electrode activity by glutathione concentrations >0.1 mM.     

Copper Adsorption on Chitosan-Derived Schiff Bases

The adsorption of Cu(II) ions onto the chitosan derived Schiff bases obtained from the condensation of chitosan with salicyaldehyde (polymer I), 2,4-dihydroxybenzaldehyde (polymer II) and with 4-(diethylamino) salicyaldehyde (polymer III) in aqueous solutions was investigated. Batch adsorption experiments were carried out as a function of contact time, pH, and polymer mass. The amount of metal-ion uptake of the polymers was determined by using atomic absorption spectrometry (AAS) and the highest Cu(II) ions uptake was achieved at pH 7.0 and by using sodium perchlorate as an ionic strength adjuster for polymers I, II, and III. The isothermal behavior and the kinetics of adsorption of Cu(II) ions on these polymers with respect to the initial mass of the polymer and temperature were also investigated; adsorption isothermal equilibrium data could be clearly explained by the Langmuir equation. The experimental data of the adsorption equilibrium from Cu(II) solution correlates well with the Langmuir isotherm equation.     

Adsorptive removal of Cr(III) from aqueous solution using tripolyphosphate cross-linked chitosan beads

Chitosan tripolyphosphate (CTPP) beads were prepared at two different cross-linking densities and adsorption of Cr(III) onto it were studied as a function of different operational parameters such as solution pH, equilibration time and initial Cr(III) ion concentration. Higher cross-linked beads were found to have more adsorption capacity at all the experimental pH employed (pH = 3–5), whereas adsorption capacity is found to increase with increase in pH. Adsorption data were analyzed using Langmuir and Freundlich isotherm models. Langmuir model is found be more suitable to explain the experimental results with a monolayer adsorption capacity of 469.5 mg/g. Among the kinetic models used, pseudo-second order kinetic model could best describe the adsorption process. Competition experiments done in presence of Na(I), Mg(II), Ca(II), Al(III) and Fe(III) revealed that, except in the case of Al(III), adsorption of Cr(III) is not significantly affected by the presence of foreign cations. NaCl is found to be a suitable leaching agent for the desorption of adsorbed Cr(III) from CTPP beads. FTIR spectroscopic investigations confirmed that phosphate groups are the principal binding site responsible for the sorption of Cr(III) onto CTPP beads.     

Biocompatible and label-free amperometric immunosensor for hepatitis B surface antigen using a sensing film composed of poly(allylamine)-branched ferrocene and gold nanoparticles

An amperometric immunosensor has been developed for sensitive determination of hepatitis B surface antigen as a model protein. A glassy carbon electrode was modified with an assembly of positively charged poly(allylamine)-branched ferrocene (PAA-Fc) and negatively charged gold nanoparticles (Au NPs). The formation of PAA-Fc effectively avoids the leakage of Fc, retains its electrochemical activity, and enhances the conductivity of the composite. The adsorption of Au NPs onto the PAA-Fc matrix provides sites for the immobilization of the antigen and a favorable micro-environment to maintain its activity. The morphologies and electrochemistry of the sensing film were investigated via scanning electron microscopy, electrochemical impedance spectroscopy, and cyclic voltammetry. Factors influencing the performance of the immunosensor were studied in detail. The concentration of the antigen can be quantitated (by measuring the decrease of the amperometric response resulting from the specific binding between antigen and antibody) in the range between 0.1 and 150?ng?mL^?C1, with a detection limit of 40?pg?mL^?C1 (S/N = 3). The method is economical, efficient, and potentially attractive for clinical immunoassays.

Fast recovery of Au (III) and Ag(I) via amine-modified zeolitic imidazolate framework-8

In this paper, zeolitic imidazolate framework-8 modified by the ethanediamine (NH₂-ZIF-8) was employed for adsorbing Au (III) and Ag(I) from aqueous solutions. The adsorption capacities of NH₂-ZIF-8 towards Au (III) and Ag(I) were found to be significantly affected by the pH values of the solution. The adsorption kinetics studies show that NH₂-ZIF-8 presents a fast adsorption property towards metals, attaining 93% of adsorption equilibrium uptake for Au (III) within the first 30 min. This phenomenon can be ascribed to the coordination interaction between the amino group and Au (III). The thermodynamic data suggest that the adsorption of NH₂-ZIF-8 towards Au (III) is endothermic process, while that for Ag(I) is exothermic. The maximum adsorption capacities of NH₂-ZIF-8 toward Au (III) and Ag(I) can be achieved to 357 mg·g⁻¹ and 222.25 mg·g⁻¹, respectively. The metal ions interference results show that Cu (II) and Ni (II) hardly have no interference on Au (III) adsorption in e-waste containing 1500 mg·l⁻¹ Cu (II),100 mg·l⁻¹ Ni (II) and 10 mg·l⁻¹ Au (III); while for Ag(I), Cd (II) and Zn (II) have little interference on Ag(I) adsorption in the hybrid solutions containing Ag(I), Ni (II), Cd (II) and Zn (II) with equal concentration (50 mg·l⁻¹), but Ni (II) interference most. The XPS study shows that partial Au (III) was reduced to Au(I), and that Ag(I) was completely reduced to Ag(0) during the adsorption process. The abundant of active sites of NH₂-ZIF-8 containing C=N, N-H, and Zn-OH groups play a key role in the adsorption of Au (III) and Ag(I). In addition, electrostatic interaction can be responsible for the adsorption of Au (III) by NH₂-ZIF-8. The regeneration experiments results show that the adsorption capacities of NH₂-ZIF-8 towards Au (III) and Ag(I) can maintain after three cycles. This work provides a reliable method to improve the adsorption kinetics for metal ions.     

Spectroelectrochemical examination of the interaction between bacterial cells and gold electrodes

The interaction between bacterial cells of Pseudomonas fluorescens (ATCC 17552) and gold electrodes was analyzed by cyclic voltammetry (CV) and attenuated total reflection-surface-enhanced infrared absorption spectroscopy (ATR-SEIRAS). The voltammetric evaluation of cell adsorption showed a decrease in the double-layer capacitance of polyoriented single-crystal gold electrodes with cell adhesion. As followed by IR spectroscopy in the ATR configuration, the adsorption of bacterial cells onto thin-film gold electrodes was mainly indicated by the increase in intensity with time of amide I and amide II protein-related bands at 1664 and 1549 cm(-1), respectively. Bands at 1448 and 2900 cm(-1) corresponding to the scissoring and the stretching bands of CH2 were also detected, together with a minor peak at 1407 cm(-1) due to the vs COO- stretching. Weak signals at 1237 cm(-1) were due to amide III, and a broad band between 1100 and 1200 cm(-1) indicated the presence of alcohol groups. Bacteria were found to displace water molecules and anions coadsorbed on the surface in order to interact with the electrode intimately. This fact was evidenced in the SEIRAS spectra by the negative features appearing at 3450 and 3575 cm-1, corresponding to interfacial water directly interacting with the electrode and water associated with chloride ions adsorbed on the electrode, respectively. Experiments in deuterated water confirmed these assignments and allowed a better estimation of amide absorption bands. In CV experiments, an oxidation process was observed at potentials higher than 0.4 V that was dependent on the exposure time of electrodes in concentrated bacterial suspensions. Adsorbed bacterial cells were found to get closer to the gold surface during oxidation, as indicated by the concomitant increment in the main IR bacterial signals including amide I, a sharp band at 1240 cm(-1), and a broad one at 1120 cm(-1) related to phosphate groups in the bacterial membranes. It is proposed to be due to the oxidation of lipopolysaccharides on the outermost bacterial surface.