Preparation and gas chromatographic characterization of dibenzyl crown ether stationary phases

Summary Two crown ethers, di(tert-butylbenzo)-propyl-15-crown-5 polysiloxane (PSO-DTB-15C5) and dibenzo-propyl-15-crown-5 polysiloxane (PSO-DB-15C5) have been synthesized and coated onto fused-silica capillary columns. The chromatographic characteristics, including column efficiency, polarity, phase transition temperature, operating temperature range and selectivity, were studied.Excellent selectivity was obtained for the separation of polar position isomers, especially phenol and dinitrotoluene isomers. The separation mechanism is discussed.     

Method for determination of methyl tert-butyl ether in gasoline by gas chromatography

A simple method for the determination of methyl tert-butyl ether (MTBE) in gasoline has been developed. The separation of MTBE from other analytes was controlled by the use of gas chromatography–mass spectrometry in the full scan mode using the characteristic primary, secondary and tertiary ions m/z 73, 57 and 43. The sample mass spectrum did not show any superimposition of other analytes. The separation from the common gasoline component 2-methylpentane was sufficient for reliable quantitation. An application of the developed conditions using gas chromatography with flame ionization detection was performed by the analysis of regular, euro super, super premium unleaded and ‘Optimax’ gasoline from petrol stations in the area of Frankfurt/Main, Germany. Regular unleaded gasoline shows an average MTBE content of 0.4% (w/w), whereas the MTBE content in euro super gasoline varies between 0.4 and 4.2% (w/w). The blending of MTBE to super premium has increased from 8.2% (w/w) in 1998 to 9.8% (w/w) on average in 1999. The recently introduced gasoline ‘Optimax’ shows an average MTBE content of 11.9% (w/w). The presented method might also be used for the analysis of other ethers, such as ethyl tert-butyl ether, which requires the use of another internal standard.     

气相色谱法同时测定树脂中氯化苄、苄醇和苯酚

对于通用型酚醛树脂和专用型酚醛树脂,其游离酚的分析方法通常采用容量法。但对碳素材料专用酚醛树脂,由于在生产时添加氯化苄对酚醛树脂进行改性,使树脂能浸润碳素材料的中心。这种树脂的生产过程控制和产品质量检验时,涉及游离酚、氯化苄和苄醇的分析测定,如果采用分别测定,其操作相当繁琐,准确性也不高。在常规方法蒸馏苯酚的过程中,氯化苄和苄醇也会被蒸馏出来,蒸馏出来的氯化苄和苄醇对苯酚的容量分析有干扰。在此基础之上,对氯化苄、苄醇和苯酚的蒸馏进行回收率测定,结果表明回收率满足要求。因此,本文建立了气相色谱法同时测定碳素材料专用树脂中的氯化苄、苄醇和苯酚的分析方法。即采用与容量分析方法一样的样品前期处理（酒精溶解样品、水浴蒸馏）,使游离酚、氯化苄和苄醇同时与树脂分离后,采用气相色谱法测定。本方法使测定步骤简化,可用于氯化苄改性的专用酚醛树脂的科研和生产控制。     

Method for determination of methyl tert-butyl ether in gasoline by gas chromatography

A simple method for the determination of methyl tert-butyl ether (MTBE) in gasoline has been developed. The separation of MTBE from other analytes was controlled by the use of gas chromatography–mass spectrometry in the full scan mode using the characteristic primary, secondary and tertiary ions m/z 73, 57 and 43. The sample mass spectrum did not show any superimposition of other analytes. The separation from the common gasoline component 2-methylpentane was sufficient for reliable quantitation. An application of the developed conditions using gas chromatography with flame ionization detection was performed by the analysis of regular, euro super, super premium unleaded and ‘Optimax’ gasoline from petrol stations in the area of Frankfurt/Main, Germany. Regular unleaded gasoline shows an average MTBE content of 0.4% (w/w), whereas the MTBE content in euro super gasoline varies between 0.4 and 4.2% (w/w). The blending of MTBE to super premium has increased from 8.2% (w/w) in 1998 to 9.8% (w/w) on average in 1999. The recently introduced gasoline ‘Optimax’ shows an average MTBE content of 11.9% (w/w). The presented method might also be used for the analysis of other ethers, such as ethyl tert-butyl ether, which requires the use of another internal standard.     

气相色谱法测定酚醛树脂中的氯化苄

氯化苄在有机工业中得到广泛应用,是生产碳素材料专用酚醛树脂的原料之一,酚醛树脂产品中氯化苄的含量必须通过测定加以控制。通常氯化苄的测定方法主要有重量法和气相色谱法等。由于树脂大分子和氯化苄分子较难分离,直接采用气相色谱法测定其中的氯化苄困难较大。本文用酒精溶解碳素材料专用酚醛树脂,加一定量的水作为混溶剂,然后用氯仿萃取其中的氯化苄,萃取分离后的氯化苄等物质,再用气相色谱法分离,测定结果满意。     

Spectrophotometric determination of germaniun with phenylflurorone after benzyl alcohol extraction

A procedure has been developed for the determination of traces of germanium with phenylflourone using benzyl alcohol extraction. The procedure is very sensitive, the molar extinction having a value of 144.700. The concentration of germanium in the organic phase should be between 0.05 and 0.5μ ml.     

Degradation products generated by sonication of benzyl alcohol, a sample preparation solvent for the determination of residual solvents in pharmaceutical bulks, on capillary gas chromatography

Benzyl alcohol used as the sample preparation solvent in the determination of residual solvents in pharmaceutical bulks yielded benzene, toluene, and benzaldehyde on capillary gas chromatography (GC) by sonication. The factors responsible for compounds generated are discussed. The quality of benzyl alcohol and the type of sonicator were not involved in the generation of benzene, toluene, and benzaldehyde, whereas matrix contributions were observed. The degradation profiles of benzyl alcohol and its analogous compounds obtained by pyrolysis-GC/mass spectrometric analysis were similar to those obtained by sonication, suggesting that benzyl alcohol is degraded by the high local heat generated by sonication. Consequently, no matter how long it may take to dissolve bulk substances in benzyl alcohol completely, we do not recommend the use of a sonicator in sample preparation for the determination of residual solvents in pharmaceutical bulks.     

Skeletal rearrangements on chemical ionization of dibenzyl ether and derivatives

Protonated molecular ions of dibenzyl ether, formed by chemical ionization using hydrogen and isobutane as reagent gases, undergo skeletal rearrangements to lose water and formaldehyde, both in the ion source and the flight path. The rearrangements have been elucidated by deuterium labelling and chemical substitution. The water lost contains the reagent proton and an aromatic hydrogen atom, and the aromatic hydrogen atoms have been shown to be mobile prior to the reaction. It is proposed that the skeletal rearrangement for water loss is initiated by protonation on the ether oxygen atom, followed by benzyl migration. The formaldehyde lost contains benzylic hydrogen atoms exclusively, and it is proposed that the skeletal rearrangement is preceded by hydrogen rearrangement of an oxygen protonated molecular ion to a ring protonated molecular ion. Daughter ion structures are supported by comparisons of their collision induced dissociation spectra with those of isomeric ions prepared by alternative routes.     

Rapid chiral separation and impurity determination of levofloxacin by ligand-exchange chromatography

A sensitive, simple, and accurate method for determination of levofloxacin and its (R)-enantiomer was developed to determine the chiral impurity of levofloxacin in Cravit Tablets material by ligand-exchange high performance liquid chromatography. The effects of different kinds of ligands, concentration of ligands in mobile phase, organic modifier, pH of mobile phase, and temperature on enantioseparation were investigated and evaluated. Chiral separation was performed on a conventional C₁₈ column, where the mobile phase consisted of a methanol-water solution (containing10 mmol L⁻¹l-leucine and 5 mmol L⁻¹ copper sulfate) (88:12, v/v) and its flow-rate was set at 1.0 mL min⁻¹. The conventional C₁₈ column offers baseline separation of two enantiomers with a resolution of 2.4 in less than 20 min. Thermodynamic data (ΔΔH and ΔΔS) obtained by Van’t Hoff plots revealed the chiral separation is an enthalpy-controlled process. The standard curves showed excellent linearity over the concentration range from 0.5 to 400 mg L⁻¹ for levofloxacin and its (R)-enantiomer. The linear correlation equations are: y = 1.33 × 10⁵x + 6297 (r = 0.9991) and y = 1.34 × 10⁵x + 3565 (r = 0.9997), respectively. The relative standard deviation (RSD) of the method was below 2.3% (n = 3).     

Analysis of volatile fatty acids by gas chromatography separation of benzyl esters

Volatile fatty acids in aqueous media were esterfied in situ with phenyldiazomethane (PDM). Complete esterification was achieved in 3 h at 40°C under continuous stirring of an ether/water system. The process involved immediate transfer of benzyl esters into the organic phase. The separation of benzyl esters mixtures was carried out in glass capillary GC columns. The retention data and FID molar responses were determined for C1 to C6 acid benzyl esters, including 2-methylpropionic, 3-methylbutyric, 2-methylvaleric, and 2-ethylbutyric acid. An unusual relationship was observed between benzyl ester relative molar responses and carbon atom number.     

Determination of benzyl alcohol and its metabolite in plasma by reversed-phase high-performance liquid chromatography.

A study undertaken following recent reports of deaths in neonatal children associated with the use of benzyl alcohol resulted in the development of a stability-indicating high-performance liquid chromatographic assay of benzyl alcohol in plasma using benzocaine as internal standard. Thawed plasma samples were diluted and subjected to solid-phase extraction using Extrelut and eluted with ethyl acetate. The evaporated eluate was reconstituted with mobile phase and chromatographed on a C18 column with water-acetonitrile-glacial acetic acid as mobile phase and detection at 254 nm. Baseline separation was achieved within 12 min for benzyl alcohol, benzaldehyde, benzoic acid, hippuric acid and benzocaine. Peak-height ratios were linear over 80-640 ng of benzyl alcohol injected (r = 0.998) and over 10-80 ng of benzoic acid injected (r = 0.999). Benzaldehyde and hippuric acid were not quantitated because these compounds were not detectable in actual dog plasma. Validation studies by spiking dog plasma with benzyl alcohol and benzoic acid gave overall percent recoveries (+/- relative standard deviation, n = 4) of 98.3 +/- 3.0 and 101.4 +/- 7.6%, respectively. The method was applied to the assay of actual plasma samples. Since benzyl alcohol is very susceptible to oxidation to benzaldehyde and benzoic acid, its purity in bulk liquid samples can be determined by this method.     

Indirect determination of isocyanates by gas chromatography

A gas chromatographic method was developed to determine the purity of synthesized isocyanate monomers, specifically isocyanatoacrylates, and to determine the isocyanate content of synthesized polymers and prepolymers. The method is a modification of an ASTM procedure in which an isocyanate is allowed to react with excess di-n-butylamine. In the ASTM method, the amount of isocyanate present is calculated indirectly from the amount of unreacted di-n-butylamine, determined by back titration with standard hydrochloric acid. Determination of the excess di-n-butylamine by the gas chromatographic method developed has the advantages of providing better precision and requiring less sample than the titrimetric method. The two methods were compared using phenyl isocyanate as a model test compound. A synthesized monomer, methyl alpha-isocyanatoacrylate, was also analyzed, for comparison by both methods.     

Development and features of hydro-membrane gas chromatography.

Hydro-membrane gas chromatography (HMGC) is achieved by the annular condensation of water in a capillary column at less than 70 degrees C. The annular membrane of water is formed as a result of the wettability of the stationary phase, which is induced at a water contact angle ranging from 75 degrees to 79 degrees, as derived from a solubility parameter (delta) range of 15.7 +/- 0.3 MPa(1/2) of the coated resin. The range of the liquid to gas volume ratio (beta) required to support the annular membrane should be kept between 0.00005 and 0.0003. In the case of a 0.25-mm i.d. column, the ratio can be set by the combination of a 0.1 to 0.2 microl min(-1) water supply rate and helium gas flow rate. Separation by HMGC develops not only a gas-solid partition but also a focusing effect on the water membrane. One feature of HMGC is that it gives a non-adsorption chromatogram based on the blocking effect of pre-adsorbed water; furthermore, despite the presence of a relatively large quantity of water, the electron impact ionization efficiency is kept the same as in the usual GC/MS condition. The detection limit with the injection of 1 microl of aquatic solution was estimated to be less than 0.1 ppb of low-molecular-weight fatty acids with s/n = 5 on a mass chromatogram at m/z 45. The HMGC/EI-MS system can be applied to the trace analysis of C1 to C3 volatile acids, volatile inorganic acids, and halogenated organic acids in water.     

Electronic spectra of paramethoxy benzyl alcohol and parachloro benzyl cyanide

The electronic absorption spectra of paramethoxy benzyl alcohol (pmba) and parachloro benzyl cyanide (pcbc) are described. The broad features of the spectra of the molecules are consistent with allowed transition forC _2v symmetry. However, the solid state and glass matrix spectra of pmba at 77K indicate possible deviation from planarity in the structure of the molecule. In pcbc, it is pointed out that intensity borrowing may be responsible for the large intensity of the vibrationally-induced part of the spectra, in which non-totally symmetric vibrations are excited.     

Determination of melissyl alcohol by capillary column gas chromatography

Summary For accurate determination of polar, high-boiling melissyl alcohol in mixtures containing also low-boiling components by capillary column gas chromatography with hot split injection, all experimental paramenters, such as the injection procedure, insert size and design, injector temperature, sample size, solvent and carrier gas nature, etc. must be optimized. Of the factors affecting the quantitation the nature of the insert packing material is of the greatest importance. With the commonly used packing material, quartz wool, in the insert, a much lower than true melissyl alcohol concentration was obtained. Accurate quantitation was only possible when stop-flow injection, together with an insert packed with glass beads was used.